POWER
LPS200-M Series
250 Watts
Total Power: 125 - 250 Watts
Input Voltage: 90 - 264 Vac
# of Outputs: Single
SPECIAL FEATURES
Medical and ITE safeties
Active power factor correction
3” x 5” footprint
Less than 1U high
EN61000-3-2 compliant
Remote sense
Power fail
Adjustable main output
Built-in Class B EMI lter
Overvoltage protection
Overload protection
Thermal overload protection
Isolated 12 V Fan output
LPX200 enclosure kit available
RoHS compliant
SAFETY
TUV 60950, 60601-1
UL 60950, 60601-1
cULus 60950, 60601-1
CB Certicate & report
CE Mark (LVD)
Electrical Specications
Input
Input ra nge 90 - 264 Vac; 120 - 300 Vdc
Frequency 47 - 63 Hz
Inrush current 50 A max., cold start @ 25 °C
Efciency 86% typical at full load
EMI/RFI FCC Class B conducted; CISPR22 Class B conducted;
EN55022 Class B conducted; VDE0878PT3 Class B conducted
Power factor 0.99 typical
Safety ground
leakage current
275 µA @ 50/60 Hz, 264 Vac input
Output
Maximum power 125 W for convection (100 W for LPS202-M); 250 W (200 W for
LPS202-M) with 30CFM forced air
Adjustment range ± 10% minimum on the main outputs
Fan output 12 V @ 0.5 A convection, @ 1 A forced air isolated, ± 10%
Hold-up time 16 ms @ 250 W load, 120 Vac input
Overload protection Short circuit protection on all outputs. Case overload protected @
110 - 160% above rating
Overvoltage protection 15 - 50% above nominal output
Logical Control
Power failure Open collector logic signal goes high 100 - 500 msec after main
output; it goes low at least 6 msec before loss of regulation
Remote sense Compensates for 0.5 V lead drop min. Will operate without remote
sense connected. Reverse connection protected.
Data Sheet
LPS200-M Series Data Sheet
Environmental Specications
Operating temperature 0 °C to 50 °C ambient derate each output as 2.5% per degree from 50° to 70 °C. -20 °C start up
Storage temperature -40 °C to +85 °C
Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity Operating; non-condensing 10% to 95% RH
Vibration IEC68-2-6 to the levels of IEC721-3-2
MTBF calculated 1 million hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore
Pin Assignments
Connector LPS200-M
SK1 Pin 1 Neutral
Pin 3 Line
SK2 TB-1 Common
TB-2 Main output
SK3 Pin 1 +V1 Remote sense
Pin 2 -V1 Remote sense
Pin 3 N/C
Pin 4 N/C
Pin 5 +Power fail
Pin 6 Common
Pin 7 N/C
Pin 8 Common
Pin 9 +12 V Fan
Pin 10 +12 Fan Return (isolated)
Mating Connectors
AC Input
(SK1)
Molex 09-50-8031 (connector)
PINS: 08-52-0072
AC Ground Molex 01-90020001
DC Output (SK2) Molex 19141-0058 or 19099-0044
Spade lug based on Cable Ampacity/AWG
Control Sense
(SK3)
Molex 90142-1110 (USA)
PINS: 90119-2110 or
Amp: 87977-3
PINS: 87309-8 or
Landwin: 2580S1003
PINS: 2583T021V
Artesyn Embedded Technologies Connector Kit #70-841-020,
includes all of the above.
1. Specications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm)
3. Mounting holes MH1 and MH2 should be grounded for EMI purposes.
4. Mounting hole MH1 is safety ground connection.
5. Specications are for convection rating at factory settings at 115 VAC input, 25 °C
unless otherwise stated.
6. This power supply requires mounting on metal standoffs 0.20” (5m) in height.
7. Warranty: 2 years
8. Weight: 0.75 lb/0.34 kg
Ordering Information
Model Number Output Voltage Minimum
Load
Maximum Load with
Convection Cooling
Maximum Load with
30CFM Forced Air
Peak Load Regulation2Ripple
P/P (PARD)3
LPS202-M 5 V 0 A 20 A 40 A 44 A ± 2% 50 mV
LPS203-M 12 V 0 A 10.3 A 20.8 A 22 A ± 2% 120 mV
LPS204-M 15 V 0 A 8.3 A 16.6 A 18 A ± 2% 150 mV
LPS205-M 24 V 0 A 5.2 A 10.4 A 11.5 A ± 2% 240 mV
LPS208-M 48 V 0 A 2.6 A 5.2 A 5.8 A ± 2% 480 mV
1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3 . Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4.
This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC
compliance to appropriate standards must be veried at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is
not intended for sale to End Users.
LPS200-M Series Data Sheet
WORLDWIDE OFFICES
Americas
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and
service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. Specifications are subject to change without
notice. © 2018 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions,
please visit www.artesyn.com/legal.
www.artesyn.com
LPS200-M DS 04Jan2018
(2.5) Max
Component
Lead Protrusion
Mechanical Drawing
