Digital Attenuator
31.0 dB, 5-Bit, TTL Driver, DC-3.0 GHz
Rev. V4
MAAD-007078-000100
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
• India Tel: +91.80.4155721 • China Tel: +86.21.2407.1588
Visit www.macomtech.com for additional data sheets and product information.
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
Electrical Specifications: TA = 25°C, Z0 = 50 Ω
Parameter Frequency Units Min Typ Max
Insertion Loss DC - 3.0 GHz dB — 3.5 3.8
Attenuation Accuracy DC - 3.0 GHz
DC - 3.0 GHz
dB
dB
—
—
—
—
±(.3 +5% of atten setting)
±(.5 +7% of atten setting)
VSWR DC - 3.0 GHz Ratio — 2.0:1 2.2:1
Switching Speed —
—
ns
ns
—
—
75
20
150
50
1 dB Compression 50 MHz
0.5 - 3.0 GHz
dBm
dBm
—
—
+21
+24
—
—
Input IP3 50 MHz
0.5-3.0 GHz
dB
dB
—
—
+35
+48
—
—
Vcc — V 4.75 5.0 5.25
VIL
VIH
—
—
V
V
0.0
2.0
—
—
0.8
5.0
lin (Input Leakage Current) — uA -1.0 — 1.0
Test Conditions
—
Individual Bits 1-2-4-8-16 dB
Any Combination of Bits 1 to 31 dB
Full Range
50% Cntl to 90%/10% RF
10% to 90% or 90% to 10%
—
—
Two-tone inputs up to +5 dBm
—
LOW-level input voltage
HIGH-level input voltage
Vin = VCC or GND
Icc4 Vcc min to max,
Logic “0” or “1”
— mA — 6 10
Turn-on Current5 For guaranteed start-up — mA — — 125
Switching Noise Generated from
DC-DC Converter with
recommended capacitors
3.5 MHz dBm — -93 —
Thermal Resistance θjc — — °C/W — 35 —
ΔIcc
(Additional Supply Current
Per TTL Input Pin)
VCC = Max, Vcntrl = VCC - 2.1 V — mA — — 1.0
4. During turn-on, the device requires an initial start up current (Icc)
specified as “Turn-on Current”. Once operational, Icc will drop to the
specified levels.
5. The DC-DC converter is guaranteed to start in 100 µs as long as the
power supplies have the maximum turn-on current available for start
up.
Absolute Maximum Ratings 6,7
Parameter Absolute Maximum
Max. Input Power
0.05 GHz
0.5 - 3.0 GHz
+27 dBm
+34 dBm
VCC -0.5V ≤ VCC ≤ +6.0V
Vin8 -0.5V ≤ Vin ≤ VCC + 0.5V
Operating Temperature -40ºC to +85ºC
Storage Temperature -65ºC to +125ºC
6. Exceeding any one or combination of these limits may cause
permanent damage to this device.
7. M/A-COM does not recommend sustained operation near
these survivability limits.
8. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.
Recommended PCB Configuration 9
9. Application Note S2083 is available on line at www.macom.com