Poke-home Connector MCPCB with thermistor for LZP emitter family LZP-H0xxT1 4x6 configuration Key Features Poke-home connectors already mounted on the MCPCB for easy connections 1-channel configuration allows for easy driver control for LZP emitters Very low Thermal Resistance for MCPCB adds only 0.1C/W Zener Diodes for ESD protection On-board thermistor for common constant current source with thermal feedback option LuxiGen LZP Lens family (15 / 23 / 32) holders align with the MCPCB cutouts Optional center die control for custom emitters Description The LZP-HxxxT1, MCPCB with three 2-pin poke-home connectors provides a convenient method to connect LED Engin's LZP emitters. One 2 pin poke-home connector supports 4 parallel strings of 6 die in series; a second one is for connecting to the thermistor, and a third one is available for an optional center die for custom emitters. Four recessed features allow the use of M3 or #4-40 screws to mount the MCPCB to a heat sink. There are additional mounting holes for the complementary TIR lenses and Zener diodes for enhanced ESD protection. Standard Product Part Numbers additional parts based on emitter nomenclature LZP-H0WWT1 LZP-H0NWT1 LZP-H0CWT1 LZP-series, Warm White 24 die emitter mounted on connector board in 4x6 configuration with 1000k thermistor LZP-series, Nuetral White 24 die emitter mounted on connector board in 4x6 configuration with 1000k thermistor LZP-series, Cool White 24 die emitter mounted on connector board in 4x6 configuration with 1000k thermistor Thermistor Options Part Designator Thermistor type Resistance @ 25 -T1 Murata, PN: NCP15WF104F03RC 100k LED Engin, Inc. | 651 River Oaks Parkway | San Jose, CA 95134 USA ph +1 408 922 7200 | fax +1 408 922 0158 | em sales@LED Engin.com | www.LED Engin.com Page | 1 Rev. 1/12 RJ-B Lookup Table Product LZP-HMCPCB * Emitter J-C 0.6C/W + MCPCB RC-B 0.1C/W Emitter + MCPCB RJ-B 0.7C/W = RJ-B is the combined thermal resistance from the LED die junction to the copper core on MCPCB (RJ-C + RC-B = RJ-B). Operating Temperatures: Maximum Operation Temperature measured at Tc or thermistor: 90C Emitter on 2-channel MCPCB Dimensions (mm) Ch. 1 2 T Pad LED1+ LED1LED2+ LED2NTC NTC Emitter pin 14, 15, 17, 18 8, 5, 3, 24 2 23 na na Function Anode Cathode Anode Cathode Terminal Terminal Note for Figure 1: * Unless otherwise noted, the tolerance = 0.2 mm. angle = 1 * Slots in MCPCB are for M3 or #4-40 mounting screws. Maximum torque should not exceed 1N-m ( 8.9 lbf-in) * LED Engin recommends plastic washers to electrically insulate screws from solder pads and electrical traces. * LED Engin recommends using thermally conductive interface material when attaching the MCPCB to a heatsink * Use solid or stranded wires with gauge size, 18, 20, 22 or 24AWG. See section on Wire Insertion and Extraction for further instructions. Components used MCPCB: ESD chips: SuperMCPCB (copper) BZX585-C30 BZX585-C9 Thermistor: NCP15WF104F03RC Connectors: 00-9276-002-0-21-1-06 (Bridge Semiconductor) (NXP, for 6 LED dies in series) (NXP, for optional center die) (Murata, 100kOhm) (AVX, poke-home) LED Engin, Inc. | 651 River Oaks Parkway | San Jose, CA 95134 USA ph +1 408 922 7200 | fax +1 408 922 0158 | em sales@LED Engin.com | www.LED Engin.com Page | 2 Rev. 1/12 Wire Insertion and Extraction Instructions For the connectors it is recommended to use solid or stranded wires with gauge size, 18, 20 , 22 or 24AWG. Push in and then give slight tug on the wire to confirm that it is properly engaged. Extraction Tool References: Thin Blade Wire Extraction Tool: AVX P/N - 0692-7670-0101-000 Miniature Precision Screw Driver, 0.047" Tip Width Wire Insertion Solid conductor * Strip insulation length 4-5mm * Insert into appropriate hole to a stop * Inserted wire will be retained by contact Stranded wire conductor * Twist strands together * Insert tool into contact operation slot * Insert wire * Remove tool Wire extraction * Insert tool into contact * Extract wire * Remove tool LED Engin, Inc. | 651 River Oaks Parkway | San Jose, CA 95134 USA ph +1 408 922 7200 | fax +1 408 922 0158 | em sales@LED Engin.com | www.LED Engin.com Page | 3 Rev. 1/12 Company Information LED Engin, based in California's Silicon Valley, specializes in ultra-bright, ultra compact solid state lighting solutions allowing lighting designers & engineers the freedom to create uncompromised yet energy efficient lighting experiences. Our LuxiGenTM Platform-- an emitter and lens combination or integrated module solution, delivers superior flexibility in light output, ranging from 3w to 90w, a wide spectrum of available colors, including whites, multi-color and UV, and the ability to deliver upwards of 5,000 high quality lumens to a target. The small size, yet remarkably powerful output, allows for a previously unobtainable freedom of design wherever high-flux density, directional light is required. www.LED Engin.com Please contact Sales@LED Engin.com or (408) 492-0620 for more information. LED Engin, Inc. | 651 River Oaks Parkway | San Jose, CA 95134 USA ph +1 408 922 7200 | fax +1 408 922 0158 | em sales@LED Engin.com | www.LED Engin.com Page | 4 Rev. 1/12