www.fairchildsemi.com KA258/KA258A, KA358/KA358A, KA2904 Dual Operational Amplifier Features Description * Internally Frequency Compensated for Unity Gain * Large DC Voltage Gain: 100dB * Wide Power Supply Range: KA258/KA258A, KA358/KA358A: 3V ~ 32V (or 1.5V~ 16V) KA2904 : 3V~26V (or 1.5V ~ 13V) * Input Common Mode Voltage Range Includes Ground * Large Output Voltage Swing: 0V DC to Vcc - 1.5V DC * Power Drain Suitable for Battery Operation. The KA258 series consist of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltage. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifier, DC gain blocks and all the conventional OP-AMP circuits which now can be easily implemented in single power supply systems. 8-DIP 1 8-SOIC 1 Internal Block Diagram OUT1 1 IN1 (-) 2 IN1 (+) 3 GND 4 8 7 OUT2 + VCC - 6 IN2 (-) + 5 IN2 (+) Rev. 1.0.4 (c)2011 Fairchild Semiconductor Corporation KA258/KA258A, KA358/KA358A, KA2904 Schematic Diagram (One section only) VCC Q5 Q12 Q6 Q17 Q19 Q20 Q2 Q3 R1 C1 Q4 IN(-) Q18 Q1 R2 IN(+) Q11 OUTPUT Q21 Q15 Q10 Q7 Q13 Q8 Q14 Q9 Q16 GND Absolute Maximum Ratings Parameter Symbol KA258/KA258A KA358/KA358A KA2904 Unit VCC 16 or 32 16 or 32 13 or 26 V VI(DIFF) 32 32 26 V Input Voltage VI -0.3 to +32 -0.3 to +32 -0.3 to +26 V Output Short Circuit to GND VCC15V, TA = 25C(One Amp) - Continuous Continuous Continuous - TOPR -25 ~ +85 0 ~ +70 -40 ~ +85 C +150 +150 +150 C -65 ~ +150 -65 ~ +150 -65 ~ +150 C Supply Voltage Differential Input Voltage Operating Temperature Range Maximum Junction Temperature TJ(MAX) Storage Temperature Range 2 TSTG KA258/KA258A, KA358/KA358A, KA2904 Electrical Characteristics (VCC = 5.0V, VEE = GND, TA = 25C, unless otherwise specified) KA258 KA358 KA2904 Parameter Symbol Conditions Input Offset Voltage VIO VCM = 0V to VCC -1.5V VO(P) = 1.4V, RS = 0 - 2.9 5.0 - 2.9 7.0 - 2.9 7.0 mV Input Offset Current IIO - - 3 30 - 5 50 - 5 50 nA Input Bias Current IBIAS - - 45 150 - 45 250 - 45 250 nA Input Voltage Range VI(R) VCC = 30V (KA2904, VCC = 26V) 0 - VCC -1.5 0 - VCC -1.5 0 - VCC -1.5 V RL = , VCC = 30V (KA2904, VCC = 26V) - 0.8 2.0 - 0.8 2.0 - 0.8 2.0 mA RL = , VCC = 5V - 0.5 1.2 - 0.5 1.2 - 0.5 1.2 mA 50 100 - 25 100 - 25 100 - V/mV 26 - - 26 - - 22 - - V 27 28 - 27 28 - 23 24 - V - 5 20 - 5 20 5 20 mV Supply Current ICC Large Signal Voltage Gain GV Output Voltage Swing VO(H) VO(L) VCC = 15V, RL = 2k VO(P) = 1V to 11V VCC = 30V RL = 2k (VCC = 26V for KA2904) RL = 10k VCC = 5V, RL = 10k Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit CommonMode Rejection Ratio CMRR - 70 85 - 65 80 - 50 80 - dB Power Supply Rejection Ratio PSRR - 65 100 - 65 100 - 50 100 - dB - 120 - - 120 - - 120 - dB Channel Separation CS Short Circuit to GND ISC - - 40 60 - 40 60 - 40 60 mA ISOURCE VI(+) = 1V, VI(-) = 0V VCC = 15V, VO(P) = 2V 20 30 - 20 30 - 20 30 - mA VI(+) = 0V, VI(-) = 1V VCC = 15V, VO(P) = 2V 10 15 - 10 15 - 10 15 - mA VI(+) = 0V, VI(-) = 1V VCC = 15V, VO(P) = 200mV 12 100 - 12 100 - - - - A - - VCC - - VCC - - VCC V Output Current Differential Input Voltage ISINK VI(DIFF) f = 1kHz to 20kHz (Note1) - Note: 1. This parameter, although guaranteed, is not 100% tested in production. 3 KA258/KA258A, KA358/KA358A, KA2904 Electrical Characteristics (Continued) (VCC = 5.0V, VEE = GND, unless otherwise specified) The following specification apply over the range of -25C TA +85C for the KA258; and the 0 C TA +70C for the KA358; and the -40C TA +85C for the KA2904 Parameter Symbol Input Offset Voltage VIO Input Offset Voltage Drift VIO/T KA258 KA358 KA2904 Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit VCM = 0V to VCC -1.5V VO(P) = 1.4V, RS = 0 - - 7.0 - - 9.0 - - 10.0 mV RS = 0 - 7.0 - - 7.0 - - 7.0 - V/C - - - 100 - - 150 - 45 200 nA IIO/T - - 10 - - 10 - - 10 - pA/C Input Bias Current IBIAS - - 40 300 - 40 500 - 40 500 nA Input Voltage Range VI(R) VCC = 30V (KA2904,VCC = 26V) 0 - VCC -2.0 0 - VCC -2.0 0 - VCC -2.0 V Large Signal Voltage Gain GV VCC = 15V, RL=2.0k VO(P) = 1V to 11V 25 - - 15 - - 15 - - V/mV 26 - - 26 - - 22 - - V 28 - 27 28 - 23 24 - V - 5 20 - 5 20 - 5 20 mV Input Offset Current Input Offset Current Drift Output Voltage Swing Output Current Differential Input Voltage 4 Conditions IIO VO(H) VCC = 30V (VCC = 26V for KA2904) RL = 2k VO(L) VCC = 5V, RL=10k RL = 10k 27 ISOURCE VI(+) = 1V, VI(-) = 0V VCC = 15V, VO(P) = 2V 10 30 - 10 30 - 10 30 - mA ISINK VI(+) = 0V, VI(-) = 1V VCC = 15V, VO(P) = 2V 5 8 - 5 9 - 5 9 - mA - - VCC - - VCC - - VCC V VI(DIFF) - KA258/KA258A, KA358/KA358A, KA2904 Electrical Characteristics (Continued) (VCC = 5.0V, VEE = GND, TA = 25C, unless otherwise specified) Parameter Symbol Input Offset Voltage VIO Input Offset Current IIO Input Bias Current IBIAS Input Voltage Range VI(R) Supply Current ICC Large Signal Voltage Gain GV Output Voltage Swing Conditions VCM = 0V to VCC -1.5V VO(P) = 1.4V, RS = 0 KA258A KA358A Min. Typ. Max. MIn. Typ. Max. Unit - 1.0 3.0 - 2.0 3.0 mV - - 2 15 - 5 30 nA - - 40 80 - 45 100 nA VCC = 30V 0 - VCC -1.5 0 - VCC -1.5 V RL = ,VCC = 30V - 0.8 2.0 - 0.8 2.0 mA RL = , VCC = 5V - 0.5 1.2 - 0.5 1.2 mA 50 100 - 25 100 - V/mV RL = 2k 26 - - 26 - V RL = 10k 27 28 - 27 28 - V - 5 20 - 5 20 mV VCC = 15V, RL=2k VO = 1V to 11V VOH VCC = 30V VO(L) VCC = 5V, RL=10k Common-Mode Rejection Ratio CMRR - 70 85 - 65 85 - dB Power Supply Rejection Ratio PSRR - 65 100 - 65 100 - dB - 120 - - 120 - dB - 40 60 - 40 60 mA VI(+) = 1V, VI(-) = 0V VCC = 15V, VO(P) = 2V 20 30 - 20 30 - mA VI(+) = 1V, VI(-) = 0V VCC = 15V, VO(P) = 2V 10 15 - 10 15 - mA Vin(+) = 0V, Vin (-) = 1V VO(P) = 200mV 12 100 - 12 100 - A - - VCC - - VCC V Channel Separation CS Short Circuit to GND ISC ISOURCE Output Current ISINK Differential Input Voltage VI(DIFF) f = 1kHz to 20kHz (Note1) - - Note: 1. This parameter, although guaranteed, is not 100% tested in production. 5 KA258/KA258A, KA358/KA358A, KA2904 Electrical Characteristics (Continued) (VCC = 5.0V, VEE = GND, unless otherwise specified) The following specification apply over the range of -25C TA +85C for the KA258A; and the 0C TA +70C for the KA358A Parameter Input Offset Voltage Symbol VIO VCM = 0V to VCC -1.5V VO(P) = 1.4V, RS = 0 KA258A KA358A Min. Typ. Max. Min. Typ. Max. Unit - - 4.0 - - 5.0 mV VIO/T - - 7.0 15 - 7.0 20 V/C IIO - - - 30 - - 75 nA IIO/T - - 10 200 - 10 300 pA/C Input Bias Current IBIAS - - 40 100 - 40 200 nA Input Common-Mode Voltage Range VI(R) VCC = 30V 0 - VCC -2.0 0 - VCC -2.0 V VO(H) VCC = 30V RL = 2k 26 - - 26 - - V RL = 10k 27 28 - 27 28 - V VO(L) VCC = 5V, RL=10k - 5 20 - 5 20 mV Input Offset Voltage Drift Input Offset Current Input Offset Current Drift Output Voltage Swing Large Signal Voltage Gain GV VCC = 15V, RL=2.0k VO(P) = 1V to 11V 25 - - 15 - - V/mV ISOURCE VI(+) = 1V, VI(-) = 0V VCC = 15V, VO(P) = 2V 10 30 - 10 30 - mA ISINK VI(+) = 1V, VI(-) = 0V VCC = 15V, VO(P) = 2V 5 9 - 5 9 - mA - - VCC - - VCC V Output Current Differential Input Voltage 6 Conditions VI(DIFF) - KA258/KA258A, KA358/KA358A, KA2904 Typical Performance Characteristics Figure 1. Supply Current vs Supply Voltage Figure 2. Voltage Gain vs Supply Voltage Figure 3. Open Loop Frequency Response Figure 4. Large Signal Output Swing vs Frequency Figure 5. Output Characteristics vs Current Sourcing Figure 6. Output Characteristics vs Current Sinking 7 KA258/KA258A, KA358/KA358A, KA2904 Typical Performance Characteristics (Continued) Figure 7. Input Voltage Range vs Supply Voltage Figure 8. Common-Mode Rejection Ratio Figure 9. Output Current vs Temperature (Current Limiting) Figure 10. Input Current vs Temperature Figure 11. Voltage Follower Pulse Response Figure 12. Voltage Follower Pulse Response (Small Signal) 8 KA258/KA258A, KA358/KA358A, KA2904 Mechanical Dimensions Package Dimensions in millimeters #5 1.524 0.10 0.060 0.004 #4 0.018 0.004 #8 2.54 0.100 9.60 MAX 0.378 #1 9.20 0.20 0.362 0.008 ( 6.40 0.20 0.252 0.008 0.46 0.10 0.79 ) 0.031 8-DIP 5.08 MAX 0.200 7.62 0.300 3.40 0.20 0.134 0.008 3.30 0.30 0.130 0.012 0.33 0.013 MIN +0.10 0.25 -0.05 +0.004 0~15 0.010 -0.002 9 KA258/KA258A, KA358/KA358A, KA2904 Mechanical Dimensions (Continued) Package Dimensions in millimeters 8-SOIC MIN #5 10 0~ 8 +0.10 0.15 -0.05 +0.004 0.006 -0.002 3.95 0.20 0.156 0.008 5.72 0.225 0.50 0.20 0.020 0.008 1.80 MAX 0.071 MAX0.10 MAX0.004 6.00 0.30 0.236 0.012 0.41 0.10 0.016 0.004 #4 1.27 0.050 #8 5.13 MAX 0.202 #1 4.92 0.20 0.194 0.008 ( 0.56 ) 0.022 1.55 0.20 0.061 0.008 0.1~0.25 0.004~0.001 KA258/KA258A, KA358/KA358A, KA2904 Ordering Information Product Number KA358 KA358A KA358D KA358AD KA258D KA258AD Package Operating Temperature 8-DIP 0 ~ +70C 8-SOIC 8-SOIC KA2904 8-DIP KA2904D 8-SOIC -25 ~ +85C -40 ~ +85C DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 10/14/11 0.0m 001 Stock#DS400082 (c) 2011 Fairchild Semiconductor Corporation