Technical Specifications FREQUENCY Frequency Range: Vernier Range: OPERATING MODES 0.005Hz to 5MHz in 7 overlapping decade ranges with fine adjustment by verniers. 1000:1 on each range. FREQUENCY LOCKING Operating Range: Locking Accuracy: 0.5Hz to 5MHz with vernier setting within 10% to 100% of range maximum. Better than 0.01% of displayed value. DISPLAY LCD, 8 digits (11mm high) plus 14 annunciators METER FUNCTIONS (generator mode) Frequency: Amplitude: DC Offset: Auto-ranging reciprocal measurement giving 4 digit resolution for frequencies down to 1Hz; maximum resolution is 0.001Hz. Accuracy 1 digit 0.2Hz to 5MHz; accuracy 1% of range full scale below 0.2Hz Display shows peak-to-peak amplitude or rms value. Display corrected for attenuator setting. 3-digit resolution, accuracy typically 5% of range 3-digit resolution; accuracy typically 2% of setting 1 digit. Display corrected for attenuator setting OUTPUTS MAIN - 50 Ohm Amplitide 2mV to 20V peak-peak open circuit (1mV to 10V peak-peak into 50W) in four switch-selectable ranges with 20dB vernier control within each range Attenuator Ranges: 0dB, -20dB, -40dB, -60dB DC Offset Range: 10V from 50W. DC offset plus signal peak limited to 10V (5V into 50W). DC offset plus waveform attenuated proportionally by the attenuator. MAIN - 600 Ohm Alternative output socket offering the same facilities as the 50W socket. AUX OUT 0 to 5V TTL/CMOS logic levels capable of driving 2 standard TTL loads. Frequency, symmetry and phase as main outputs SWEEP OUT 3V ramp from 600W EXTERNAL COUNTER Frequency Range: Input Sensitivity: Input Impedance: Measurement Time: Resolution: Accuracy: Timebase Accuracy: 5Hz to 20MHz, fully autoranging 50mV rms (sinewave) 1MW/25pF Selectable 0.5s or 5s 6 digits in 0.5s; 7 digits in 5s 1 digit timebase accuracy 10ppm initial error; 5ppm/year ageing rate; o typically less then 0.5ppm/ C. Adjustment point for closed-case recalibration Specifications apply for the top decade of each frequency range and maximum output into 50W termination. SINE Distortion: <0.5% on 500, 5k and 50k ranges; <1% on 5, 50 and 500k ranges; all harmonics >25dB below fundamental on 5M range. Amplitude Flatness: 0.2dB to 200kHz; 2dB to 5MHz. TRIANGLE Linearity: Better than 99% to 200kHz SQUARE WAVE Rise/Fall Times: <45ns Mark - Space Ratio: 1:1 1% to 100kHz DC Range: 10V unterminated SYMMETRY Symmetry Range: Variable typically 1:9 to 9:1 (on top decade of each range), frequency divided by 10. AIM & TH UR L BY TH AND AR I N S T RU M E N T S TG550 SWEEP MODES INTERNAL Sweep Range: Sweep Rate: Sweep Mode: EXTERNAL Input Impedance: Input Sensitivity: Max. Input Voltage: Sweep Linearity: Max. Voltage Rate: >1000:1 within each range. Adjustable, typically 20ms to 20 secs. Linear or logarithmic. Sweep start and stop frequencies displayed by button press. 10kW 0 to 3V for 1000:1 sweep 10V Better than 1% 0.1V/us AMPLITUDE MODULATION Depth: Variable 0 to 100% Frequency: 400Hz (internal). DC to 20kHz (external). External Sensitivity: Approx. 2V peak-to-peak for 50% modulation. GENERAL POWER REQUIREMENTS AC Input: 220 to 240 volts 10% or 110 to 120 volts 10% 50/60Hz, Installation Category II. Consumption: 25VA max. ENVIRONMENTAL & MECHANICAL o o Operating Range: +5 C to +40 C, 20% to 80% RH. o o Storage Range: -10 C to +65 C Environmental: Indoor use at <2000m, Pollution degree 2 Safety: Complies with EN601010-1 EMC: Complies with EN61326 Size: 260(W) x 88(H) x 235(D)mm , excluding handle and feet. Weight: 1.9kg approx. Thurlby Thandar Instruments Ltd. operates a policy of continuous development and reserves the right to alter specifications without prior notice. 5MHz function generator with sweep simultaneous display of frequency & amplitude crystal controlled digital frequency locking Designed and built in Europe by: seven digit external frequency counter Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon. Cambs. PE29 7DX United Kingdom (UK) Tel: +44 (0)1480 412451 Fax: +44 (0)1480 450409 Email: info@aimtti.com Web: www.aimtti.com 82100-0077 Iss. 2A TG550 5MHz function generator with sweep digital frequency locking for exceptional accuracy and stability A state-of-the-art instrument The function generator is one of the most versatile pieces of test & measurement instrumentation available. It can generate a variety of precision waveshapes over a range of frequencies from mHz to MHz. It can provide a wide range of controlled amplitudes from a low-impedance source, and maintain constant amplitude as the frequency is varied. Voltage control of frequency enables a source of swept frequency to be generated for frequency response testing. AM and FM modulation can also be added. The TG550 represent the state-of-the-art in 5MHz analogue function generators. Exceptional waveform quality Wide range level control The TG550 provides very high waveform quality under all conditions. That means low sinewave distortion, low aberration triangle waves and fast-edged square waves with low overshoot. Unlike many competitive products good waveform quality is maintained throughout the frequency range and at low output levels. The TG550 series provides a main output with a maximum emf of 20V pk-pk from a 50 or 600 source. An amplitude vernier with a range of 20dB is combined with two switched attenuators of -20dB and -40dB to provide levels down to 2mV pk-pk unterminated. Variable DC offset of 10V is available via a center detent control. An auxiliary output provides a fixed 0V to +5V level suitable for driving both TTL and CMOS loads. Variable symmetry for pulse and ramp waveforms The TG550 series provides bi-directional variable symmetry from 1:9 to 9:1. Unlike some products, frequency is independent of symmetry setting. Wide sweep range Each range can be swept by at least 1000:1 either manually, via the external input, or using the built-in sweep generator. simultaneous display of frequency and level external frequency counter with seven digit resolution Dual digital displays for precision & convenience The TG550 incorporates a large dual section digital display. Unlike competitive products the display provides a readout not just of frequency, but of amplitude or offset simultaneously. Fast and accurate frequency measurement Auto-ranging reciprocal measurement gives 4-digit resolution with rapid update right down to Hz levels. Accuracy is within 1 digit (0.02% at full scale). To maintain a fast update at sub-Hz frequencies, the measurement mode is changed resulting in 3-digit resolution and reduced accuracy. However, when compared to the normal fixed gate-time meters used in other products the TG550 provides both higher accuracy and faster display update across the whole frequency range. Advanced internal sweep The TG550 incorporates a versatile internal sweep generator capable of providing linear or logarithmic frequency sweeps. Start and stop frequencies can be set with precision using the digital display. Sweep ranges of over 1000:1 are possible. The sweep rate is adjustable over a wide range with good setability between limits of 20ms and 20s. A sweep output socket is provided for use with an oscilloscope or an X-Y recorder. Unlike many other sweep generators, the sweep ramp is triangular which gives a superior display when using an oscilloscope to display swept frequencies. External counter with seven digit resolution The TG550 has an external counter mode which utilises the full width of the display to provide up to seven digits of resolution. The frequency range is from 5Hz up to 20MHz and the input sensitivity is better than 50mV rms. A measurement period of 0.5 or 5 seconds can be selected. A reciprocal counting measurement system is used which ensures high resolution regardless of input frequency. Thus, for example, mains frequency can be measured to a resolution of better than 1mHz. Accuracy is better than 10ppm (0.001%) and an external adjustment point allows for closed case re-calibration. Part of an extensive range RMS or peak to peak amplitude display The output level display can be selected to show any of three values: 1. The peak to peak amplitude 2. The RMS amplitude 3. The DC offset RMS values are calculated correctly for each waveform shape Frequency locking for exceptional stability The TG550 includes a digital frequency locking system that gives it a level of frequency stability that cannot be matched by conventional analogue function generators. Once the frequency has been set, pressing the Lock key engages a measure-andcorrect circuit which compensates for the small thermal and mechanical drifts that inevitably occur in an analogue generator. The frequency is compared to a crystal controlled reference and is maintained to within 0.01% of the set frequency. 0.005Hz to 5MHz frequency range Simultaneous display of frequency & amplitude Frequency locking for crystal controlled stability Precision internal linear or logarithmic sweep External frequency counter with 7 digit resolution Very high waveform quality at all frequencies & levels 20V pk-pk from 50 or 600 plus TTL/CMOS output 1000:1 frequency change by vernier or sweep voltage lnternal or external amplitude modulation up to 100% The decimal point and units are changed automatically resulting in a display of the true amplitude regardless of the attenuator setting. An display indicator warns against illegal combinations of offset and amplitude setting that would create clipping in the output stage. The display of a filter response using an oscilloscope in XY mode and a TG550 in swept frequency mode. Amplitude modulation for extra versatility The TG550 also incorporates comprehensive AM facilities. The modulation can be external or internal (via a 400Hz internal generator) with modulation levels fully variable between 0% and 100%. TTi offers a wide choice of function generators both analogue and digital, from a simple 2MHz model up to a highly sophisticated 40MHz unit. Contact TTi or visit the website for details of the full range. TG550 5MHz function generator with sweep digital frequency locking for exceptional accuracy and stability A state-of-the-art instrument The function generator is one of the most versatile pieces of test & measurement instrumentation available. It can generate a variety of precision waveshapes over a range of frequencies from mHz to MHz. It can provide a wide range of controlled amplitudes from a low-impedance source, and maintain constant amplitude as the frequency is varied. Voltage control of frequency enables a source of swept frequency to be generated for frequency response testing. AM and FM modulation can also be added. The TG550 represent the state-of-the-art in 5MHz analogue function generators. Exceptional waveform quality Wide range level control The TG550 provides very high waveform quality under all conditions. That means low sinewave distortion, low aberration triangle waves and fast-edged square waves with low overshoot. Unlike many competitive products good waveform quality is maintained throughout the frequency range and at low output levels. The TG550 series provides a main output with a maximum emf of 20V pk-pk from a 50 or 600 source. An amplitude vernier with a range of 20dB is combined with two switched attenuators of -20dB and -40dB to provide levels down to 2mV pk-pk unterminated. Variable DC offset of 10V is available via a center detent control. An auxiliary output provides a fixed 0V to +5V level suitable for driving both TTL and CMOS loads. Variable symmetry for pulse and ramp waveforms The TG550 series provides bi-directional variable symmetry from 1:9 to 9:1. Unlike some products, frequency is independent of symmetry setting. Wide sweep range Each range can be swept by at least 1000:1 either manually, via the external input, or using the built-in sweep generator. simultaneous display of frequency and level external frequency counter with seven digit resolution Dual digital displays for precision & convenience The TG550 incorporates a large dual section digital display. Unlike competitive products the display provides a readout not just of frequency, but of amplitude or offset simultaneously. Fast and accurate frequency measurement Auto-ranging reciprocal measurement gives 4-digit resolution with rapid update right down to Hz levels. Accuracy is within 1 digit (0.02% at full scale). To maintain a fast update at sub-Hz frequencies, the measurement mode is changed resulting in 3-digit resolution and reduced accuracy. However, when compared to the normal fixed gate-time meters used in other products the TG550 provides both higher accuracy and faster display update across the whole frequency range. Advanced internal sweep The TG550 incorporates a versatile internal sweep generator capable of providing linear or logarithmic frequency sweeps. Start and stop frequencies can be set with precision using the digital display. Sweep ranges of over 1000:1 are possible. The sweep rate is adjustable over a wide range with good setability between limits of 20ms and 20s. A sweep output socket is provided for use with an oscilloscope or an X-Y recorder. Unlike many other sweep generators, the sweep ramp is triangular which gives a superior display when using an oscilloscope to display swept frequencies. External counter with seven digit resolution The TG550 has an external counter mode which utilises the full width of the display to provide up to seven digits of resolution. The frequency range is from 5Hz up to 20MHz and the input sensitivity is better than 50mV rms. A measurement period of 0.5 or 5 seconds can be selected. A reciprocal counting measurement system is used which ensures high resolution regardless of input frequency. Thus, for example, mains frequency can be measured to a resolution of better than 1mHz. Accuracy is better than 10ppm (0.001%) and an external adjustment point allows for closed case re-calibration. Part of an extensive range RMS or peak to peak amplitude display The output level display can be selected to show any of three values: 1. The peak to peak amplitude 2. The RMS amplitude 3. The DC offset RMS values are calculated correctly for each waveform shape Frequency locking for exceptional stability The TG550 includes a digital frequency locking system that gives it a level of frequency stability that cannot be matched by conventional analogue function generators. Once the frequency has been set, pressing the Lock key engages a measure-andcorrect circuit which compensates for the small thermal and mechanical drifts that inevitably occur in an analogue generator. The frequency is compared to a crystal controlled reference and is maintained to within 0.01% of the set frequency. 0.005Hz to 5MHz frequency range Simultaneous display of frequency & amplitude Frequency locking for crystal controlled stability Precision internal linear or logarithmic sweep External frequency counter with 7 digit resolution Very high waveform quality at all frequencies & levels 20V pk-pk from 50 or 600 plus TTL/CMOS output 1000:1 frequency change by vernier or sweep voltage lnternal or external amplitude modulation up to 100% The decimal point and units are changed automatically resulting in a display of the true amplitude regardless of the attenuator setting. An display indicator warns against illegal combinations of offset and amplitude setting that would create clipping in the output stage. The display of a filter response using an oscilloscope in XY mode and a TG550 in swept frequency mode. Amplitude modulation for extra versatility The TG550 also incorporates comprehensive AM facilities. The modulation can be external or internal (via a 400Hz internal generator) with modulation levels fully variable between 0% and 100%. TTi offers a wide choice of function generators both analogue and digital, from a simple 2MHz model up to a highly sophisticated 40MHz unit. Contact TTi or visit the website for details of the full range. Technical Specifications FREQUENCY Frequency Range: Vernier Range: OPERATING MODES 0.005Hz to 5MHz in 7 overlapping decade ranges with fine adjustment by verniers. 1000:1 on each range. FREQUENCY LOCKING Operating Range: Locking Accuracy: 0.5Hz to 5MHz with vernier setting within 10% to 100% of range maximum. Better than 0.01% of displayed value. DISPLAY LCD, 8 digits (11mm high) plus 14 annunciators METER FUNCTIONS (generator mode) Frequency: Amplitude: DC Offset: Auto-ranging reciprocal measurement giving 4 digit resolution for frequencies down to 1Hz; maximum resolution is 0.001Hz. Accuracy 1 digit 0.2Hz to 5MHz; accuracy 1% of range full scale below 0.2Hz Display shows peak-to-peak amplitude or rms value. Display corrected for attenuator setting. 3-digit resolution, accuracy typically 5% of range 3-digit resolution; accuracy typically 2% of setting 1 digit. Display corrected for attenuator setting OUTPUTS MAIN - 50 Ohm Amplitide 2mV to 20V peak-peak open circuit (1mV to 10V peak-peak into 50W) in four switch-selectable ranges with 20dB vernier control within each range Attenuator Ranges: 0dB, -20dB, -40dB, -60dB DC Offset Range: 10V from 50W. DC offset plus signal peak limited to 10V (5V into 50W). DC offset plus waveform attenuated proportionally by the attenuator. MAIN - 600 Ohm Alternative output socket offering the same facilities as the 50W socket. AUX OUT 0 to 5V TTL/CMOS logic levels capable of driving 2 standard TTL loads. Frequency, symmetry and phase as main outputs SWEEP OUT 3V ramp from 600W EXTERNAL COUNTER Frequency Range: Input Sensitivity: Input Impedance: Measurement Time: Resolution: Accuracy: Timebase Accuracy: 5Hz to 20MHz, fully autoranging 50mV rms (sinewave) 1MW/25pF Selectable 0.5s or 5s 6 digits in 0.5s; 7 digits in 5s 1 digit timebase accuracy 10ppm initial error; 5ppm/year ageing rate; o typically less then 0.5ppm/ C. Adjustment point for closed-case recalibration Specifications apply for the top decade of each frequency range and maximum output into 50W termination. SINE Distortion: <0.5% on 500, 5k and 50k ranges; <1% on 5, 50 and 500k ranges; all harmonics >25dB below fundamental on 5M range. Amplitude Flatness: 0.2dB to 200kHz; 2dB to 5MHz. TRIANGLE Linearity: Better than 99% to 200kHz SQUARE WAVE Rise/Fall Times: <45ns Mark - Space Ratio: 1:1 1% to 100kHz DC Range: 10V unterminated SYMMETRY Symmetry Range: Variable typically 1:9 to 9:1 (on top decade of each range), frequency divided by 10. AIM & TH UR L BY TH AND AR I N S T RU M E N T S TG550 SWEEP MODES INTERNAL Sweep Range: Sweep Rate: Sweep Mode: EXTERNAL Input Impedance: Input Sensitivity: Max. Input Voltage: Sweep Linearity: Max. Voltage Rate: >1000:1 within each range. Adjustable, typically 20ms to 20 secs. Linear or logarithmic. Sweep start and stop frequencies displayed by button press. 10kW 0 to 3V for 1000:1 sweep 10V Better than 1% 0.1V/us AMPLITUDE MODULATION Depth: Variable 0 to 100% Frequency: 400Hz (internal). DC to 20kHz (external). External Sensitivity: Approx. 2V peak-to-peak for 50% modulation. GENERAL POWER REQUIREMENTS AC Input: 220 to 240 volts 10% or 110 to 120 volts 10% 50/60Hz, Installation Category II. Consumption: 25VA max. ENVIRONMENTAL & MECHANICAL o o Operating Range: +5 C to +40 C, 20% to 80% RH. o o Storage Range: -10 C to +65 C Environmental: Indoor use at <2000m, Pollution degree 2 Safety: Complies with EN601010-1 EMC: Complies with EN61326 Size: 260(W) x 88(H) x 235(D)mm , excluding handle and feet. Weight: 1.9kg approx. Thurlby Thandar Instruments Ltd. operates a policy of continuous development and reserves the right to alter specifications without prior notice. 5MHz function generator with sweep simultaneous display of frequency & amplitude crystal controlled digital frequency locking Designed and built in Europe by: seven digit external frequency counter Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon. Cambs. PE29 7DX United Kingdom (UK) Tel: +44 (0)1480 412451 Fax: +44 (0)1480 450409 Email: info@aimtti.com Web: www.aimtti.com 82100-0077 Iss. 2A Product Summary Company name and product brands Laboratory Power Supplies Bench and system power supplies from 30 watts up to 1200 watts using linear, mixed-mode and PowerFlex regulation technologies. Thurlby Thandar Instruments Ltd. (TTi) is one of Europe's leading manufacturers of test and measurement instruments. Waveform Generators Analog and digital (DDS) function generators, true arbitrary generators, arbitrary/function generators and pulse generators. In the future, however, the full product range will be branded Aim-TTi. Products have been sold under two brand names: TTi and Aim. This changeover will be gradual and many products will continue to carry the TTi or Aim brands for some time to come. Web Addresses (URLs) Precision Measurement Instruments Benchtop DMMs, frequency counters, component measurement instruments (LCR), electronic dc loads, current probes. The preferred URL for obtaining information concerning Aim-TTi products is: www.aimtti.com (international customers) Customers in the UK should use the URL: www.aimtti.co.uk RF and EMC Test Equipment Spectrum analyzers, signal generators, frequency counters, power meters, emc measurement instruments. Customers in the USA should use the URL: www.aimtti.us Note that previous URLs such as www.tti-test.com will continue to operate for the time being. Designed and built in Europe by: Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon, Cambridgeshire PE29 7DR England (United Kingdom) Tel: +44 (0)1480 412451 Fax: +44 (0)1480 450409 Email: info@aimtti.com Web: www.aimtti.com