DT Family
17
Contents
DT Family Overview 18 DTV Series 28
Part Numbering System 18 DTMH Series 29
Dimensions 19 DTMN Series 30
Confi gurations 20 How To Instructions 31
Required Components 21-22
Special Modifi cations 22-23
Accessories 24-27
A STEP AHEAD
18
DT Family
DT Family Overview
Deutsch DT, DTM, and DTP Series environmentally sealed connectors are designed specifi cally for cable to cable
applications. The DT connectors are used in harsh environment applications where even a small degradation in connection
may be critical. Thermoplastic housings offer a wide operating temperature range and silicone rear wire and interface seals
allow the connectors to withstand conditions of extreme temperature and moisture.
The connector may be populated with either solid or stamped & formed style contacts. Contact insertion and removal does
not require any special tools. Contacts are retained in locked position by dielectric fi ngers which are molded as an integral
part of the housing. Secondary wedgelocks are assembled at the mating interfaces to ensure contact positioning.
The Deutsch DT Series general purpose connectors will provide reliability and performance on the engine or transmission,
under the hood, on the chassis, or in the cab.
DT* 06 - 2 S * - XXXX
Series
Blank = DT Series
M = DTM Series
P = DTP Series
Style
04 = Receptacle
06 = Plug
Special Modifi cations
Key (if applicable)
Contacts
P = Pin
S = Socket
Confi guration
DT Family Part Numbering System
DT Series Overview
Deutsch’s DT Series connectors offer fi eld proven reliability
and rugged quality. The DT design strengths include
optional fl ange mounting, multi-pin arrangements,
lower cost, and design fl exibility. The DT Series offers the
designer the ability to use multiple size 16 contacts, each
with 13 amp continuous capacity, within a single shell.
DTM Series Overview
Deutsch’s DTM Series connectors are the answer to all
of your smaller wire gauge applications. Building on
the DT design strengths, the DTM connector line was
developed to fi ll the need for lower amperage, multi-
pin, inexpensive connectors. The DTM Series offers the
designer the ability to use multiple size 20 contacts, each
with 7.5 amp continuous capacity, within a single shell.
DTP Series Overview
Deutsch’s DTP Series connectors are the solution for your
power application requirements. Building on both the DT
and DTM design strengths, the DTP connector line was
developed to fi ll the need for higher amperage, multi-pin,
inexpensive connectors.
The DTP Series offers the designer the ability to use
multiple size 12 contacts, each with a 25 amp continuous
capacity, within a single shell. The DTP connectors are
currently available in two and four pin confi gurations.
A STEP AHEAD
19
DT Family
Cavity
DT Plug DT Receptacle
Overall Length
A
Overall Height
B
Overall Width
C
Overall Length
D
Overall Height
E
Overall Width
F
2 1.118 (28.4) .628 (15.95) .591 (15.01) 1.708 (43.38) .670 (17.02) .675 (17.15)
3 1.118 (28.4) .934 (23.72) .718 (18.23) 1.698 (43.13) .973 (24.71) .832 (21.13)
4 1.218 (30.94) .724 (18.39) .716 (18.19) 1.808 (45.92) .776 (19.71) .820 (20.83)
6 1.218 (30.94) .891 (22.63) .716 (18.19) 1.808 (45.92) .951 (24.16) .820 (20.83)
8 1.217 (30.91) .776 (19.71) 1.465 (37.21) 1.798 (45.67) 1.000 (25.40) 1.435 (36.45)
12 1.218 (30.94) .716 (18.19) 1.597 (40.56) 1.808 (45.92) .876 (22.25) 1.597 (40.56)
Dimensions are for reference only.
DT Series Dimensions
F
D
E
F
D
A
C
B
A
C
Cavity
DTP Plug DTP Receptacle
Overall Length
A
Overall Height
B
Overall Width
C
Overall Length
D
Overall Height
E
Overall Width
F
2 1.364 (34.65) .711 (18.06) .732 (18.59) 1.861 (47.27) .869 (22.07) .732 (18.59)
4 1.364 (34.65) .960 (24.38) .868 (22.05) 1.861 (47.27) 1.069 (27.15) .868 (22.05)
Dimensions are for reference only.
DTP Series Dimensions
F
D
E
F
D
A
C
B
A
C
Cavity
DTM Plug DTM Receptacle
Overall Length
A
Overall Height
B
Overall Width
C
Overall Length
D
Overall Height
E
Overall Width
F
2 1.620 (41.15) .638 (16.21) .475 (12.07) 1.085 (27.56) .508 (12.90) .651 (16.54)
3 1.620 (41.15) .638 (16.21 .640 (16.26) 1.085 (27.56) .551 (14.00) .861 (20.73)
4 1.720 (43.69) .772 (19.61) .600 (15.24) 1.185 (30.10) .695 (17.65) .756 (19.20)
6 1.720 (43.69) .937 (23.80) .600 (15.24) 1.185 (30.10) .817 (20.75) .756 (19.20)
8 1.720 (43.69) .796 (20.22) 1.245 (31.62) 1.185 (30.10) .600 (15.24) 1.245 (31.62)
12 1.720 (43.69) .796 (20.22) 1.575 (40.01) 1.185 (30.10) .600 (15.24) 1.575 (40.01)
Dimensions are for reference only.
DTM Series Dimensions
F
E
D
F
D
A
C
B
A
C
A STEP AHEAD
20
DT Family
DTP0*-2*
2 size 12
DTP0*-4*
4 size 12
DT04-4P
4 size 16
X, X, X
Keying Options
A = A key
B = B key
C = C key
D = D key
Insert Arrangement
Insert Layout
Number and Size of Cavities
DT Family Connector Confi gurations
DTM0*-08**
8 size 20
A, B, C, D
DTM0*-12**
12 size 20
A, B, C, D
DTM0*-2*
2 size 20
DTM0*-3*
3 size 20
DTM0*-4*
4 size 20
DTM0*-6*
6 size 20
DTM Series Confi gurations
DT0*-08**
8 size 16
A, B, C, D
DT0*-12**
12 size 16
A, B, C, D
DT0*-6*
6 size 16
DT0*-2*
2 size 16
DT0*-3*
3 size 16
DT0*-4*
4 size 16
DT Series Confi gurations
DTP Series Confi gurations
A STEP AHEAD
21
DT Family
DTP Series Wedgelocks
Receptacle Plug
WP-2P Wedgelock for 2 way receptacle WP-2S Wedgelock for 2 way plug
WP-4P Wedgelock for 4 way receptacle WP-4S Wedgelock for 4 way plug
W
W
DT Series Wedgelocks
Receptacle Plug
W2P* Wedgelock for 2 way receptacle
*A, B, C, D keying available W2S* Wedgelock for 2 way plug
*A, B, C, D keying available
W3P* Wedgelock for 3 way receptacle
*J1939 keying available W3S* Wedgelock for 3 way plug
*J1939 keying available
W4P* Wedgelock for 4 way receptacle
*A, B, C, D keying available W4S* Wedgelock for 4 way plug
*A, B, C, D keying available
W6P Wedgelock for 6 way receptacle W6S Wedgelock for 6 way plug
W8P Wedgelock for 8 way receptacle W8S Wedgelock for 8 way plug
W12P Wedgelock for 12 way recep-
tacle W12S Wedgelock for 12 way plug
W
W
W
W
W
W
Required Components
Secondary Wedgelocks
Deutsch DT style electrical connectors require secondary wedgelocks which are sold separately. The wedgelocks ensure
proper contact alignment within each connector. Secondary wedgelocks are assembled at the mating interface and click
into place. If by chance the secondary wedgelocks are not properly seated during assembly, they will be pressed into locked
position during the mating of the connector.
Adding to the design fl exibility of the DT Series, several wedgelocks offer keying options. Wedgelocks for enhanced seal
retention plugs (P012) are also available.
Jiffy Splices
accept one
pin and one
socket.
Note
J
iffy Splices
a
ccep
t
one
pin and one
socket.
No
t
eNo
t
e
Wedgelocks for
enhanced plugs
(P012) are
available.
Notice
Notice
A STEP AHEAD
22
DT Family
Special Modifi cations
The DT Series connectors offer several modifi cations to enhance the design fl exibility and meet application specifi c needs.
Options include enhanced seal retention, fl anges, and connector body color just to mention a few. By combining the DT
Series connectors with the available modifi cations and accessories, the design possibilities are immense.
DTM Series Wedgelocks
Receptacle Plug
WM-2P* Wedgelock for 2 way receptacle
*A, B, C, D keying available WM-2S* Wedgelock for 2 way plug
*A, B, C, D keying available
WM-3P Wedgelock for 3 way receptacle WM-3S Wedgelock for 3 way plug
WM-4P Wedgelock for 4 way receptacle WM-4S Wedgelock for 4 way plug
WM-6P Wedgelock for 6 way receptacle WM-6S Wedgelock for 6 way plug
WM-8P Wedgelock for 8 way receptacle WM-8S Wedgelock for 8 way plug
WM-12P Wedgelock for 12 way recep-
tacle WM-12S Wedgelock for 12 way plug
W
W
W
W
W
W
W
W
W
W
W
B016 Modifi cation
The B016 receptacle modifi cation provides safety against
mis-mating. The B016 is available for the DT 12 way
connectors, DT13/15, and DTF13/15 PCB Series connec-
tors. In addition to the four keying positions (A, B, C, or
D) and color coding, the B016 enhancement gives the
user both visual and tactile proof of correct mating, thus
eliminating mis-mating opportunities during assembly.
Please note the P012 plug is the required mate for the
B016 receptacle to make the enhancement effective.
P012 Modifi cation
The DT P012 plugs provide enhanced front seal reten-
tion providing an ultra tight environmental seal. The
enhanced seal retention keeps the seal in place during
mating and unmating. The P012 modifi cation requires an
enhanced P012 wedgelock. Deutsch’s P012 modifi cation
is available in 2, 3, 4, 6, 8, and 12 cavity arrangements.
P012 plugs have a black connector body except for the 8
and 12 cavity arrangements, where the color is based on
the key.
A STEP AHEAD
23
DT Family
E007 & E008 Modifi cation
To meet the application requirements where wires
need added protection, the DT (E008) and DTM (E007)
Series may be supplied with shrink boot adapters. These
adapters accept shrink tubing.
C015 Modifi cation
The C015 modifi cation offers a reduced diameter insert
cavity allowing for a proper seal with smaller wire insula-
tion. The C015 modifi cation is also referred to as an “ E”
seal.
E004 Modifi cation
The E004 modifi cation changes the connector body
color to black.
Flange Modifi cations
Designed to simplify wire routing and assembly, DT Series
receptacles are available in many mounting confi gura-
tions and styles.
Welded fl ange
• Welded flange - BL04, BL08, CL03, L012, LE14
• Welded flange, end cap - LE07, LE11
• Welded flange, shrink boot adapter - LE08, LE12
Sealed fl ange
• Sealed flange, end cap - CL09, LE01, LE05, LE06,
LE09, LE10, LE17, LE21
• Sealed flange, shrink boot adapter - BL10, CL07
E003 Modifi cation
The E003 modifi cation offers a protective end cap
attached to the rear of the connector. There are holes in
the cap to allow the contacts to be inserted.
E005 Modifi cation
The E005 modifi cation offers a protective end cap
attached to the rear of the connector and has a black
connector body.
Jiffy Splices
accept one
pin and one
socket.
Note
Jiffy Splice
s
accept one
p
in and one
socket
.
NoteNote
For additional
modifi cations,
please consult
the factory.
Notice
Notice
A STEP AHEAD
24
DT Family
L
A
D
D
I
n
d
u
s
t
r
i
e
s
A
v
a
i
l
a
b
l
e
t
h
r
o
u
g
h
L
A
D
D
I
n
d
u
s
t
r
i
e
s
A
v
a
i
l
a
b
l
e
t
h
r
o
u
g
h
Accessories
Deutsch Industrial offers several accessory items that can be used to complement the connectors. The DT family accessories
include items such as boots, backshells, gaskets, dust caps, and mounting clips. They are designed to assist in completing the
design requirements of specifi c applications. Accessory items cover a wide array of design requirements such as assisting with
mounting, providing additional protection, and offering increased aesthetics.
Gasket P/N Connector P/N
DT3P-L012-GKT DT04-3P-L012
DT4P-L012-GKT DT04-4P-L012
DTP4P-L012-GKT DTP04-4P-L012
DT8P-L012-GKT DT04-08P*-L012
DT12-L012-GKT DT04-12P*-L012
DTM04-12P*-L012
Gaskets
Moisture, dirt, salt, sand, and road debris can all work their way into electrical panels through unsealed
mounting fl anges. Rated to operate in environments from -70°F to +225°F, these rugged high quality
neoprene gaskets form a tight seal between the panel face and connector fl ange to help keep out
destructive elements. The gaskets have a thickness of .125” and meet the UL-94-HBF, Mil-R-6130C, and
FMVSS-302 fl ammability specifi cations.
Dust Caps
The DT Series dust caps are made of either thermoplastic or durable plastisol and are designed to provide
protection for the connector interface when the two halves are not mated. The plastisol caps, available for
plugs and receptacles, are ideal for providing temporary protection from dirt, dust, and paint overspray. The
thermoplastic caps provide an environmental seal for an unmated plug.
Plastisol Dust Cap P/N Connector P/N
DTM3S-DC DTM06-3S
DT3P-DC DT04-3P
DT4P-DC DT04-4P
DT6P-DC DT04-6P
DTM12P-DC DTM04-12P*
DT12P-DC, DT12P-DC-BK DT04-12P*
DT12S-DC DT06-12S*
Thermoplastic Dust Cap P/N Connector P/N
1011-344-0205 DT06-2S
1011-345-0305 DT06-3S
1011-346-0405 DT06-4S
1011-347-0605 DT06-6S
1011-348-0805 DT06-08S*
1011-349-1205 DT06-12S*
A STEP AHEAD
25
DT Family
L
A
D
D
I
n
d
u
s
t
r
i
e
s
A
v
a
i
l
a
b
l
e
t
h
r
o
u
g
h
Receptacle Boot Description Boot Part Number
DT Series DTM Series DTP Series
2 way receptacle boot, gray DT2P-BT DTM2P-BT DTP2P-BT
2 way receptacle boot, black DT2P-BT-BK DTM2P-BT-BK DTP2P-BT-BK
3 way receptacle boot, gray DT3P-BT DTM3P-BT -
3 way receptacle boot, black DT3P-BT-BK - -
4 way receptacle boot, gray DT4P-BT DTM4P-BT DTP4P-BT
4 way receptacle boot, gray, enhanced length - - DTP4P-BT-EN
6 way receptacle boot, gray DT6P-BT DTM6P-BT -
6 way receptacle boot, black DT6P-BT-BK - -
8 way receptacle boot, gray DT8P-BT DTM8P-BT -
8 way receptacle boot, black DT8P-BT-BK - -
12 way receptacle boot, gray DT12P-BT DTM12P-BT -
12 way receptacle boot, black DT12P-BT-BK DTM12P-BT-BK -
12 way receptacle boot, gray, enhanced length DT12P-BT-EN - -
Plug Boot Description Boot Part Number
DT Series DTM Series DTP Series
2 way plug boot, gray DT2S-BT DTM2S-BT DTP2S-BT
2 way plug boot, black DT2S-BT-BK DTM2S-BT-BK -
3 way plug boot, gray DT3S-BT DTM3S-BT -
3 way plug boot, black DT3S-BT-BK DTM3S-BT-BK -
4 way plug boot, gray DT4S-BT DTM4S-BT DTP4S-BT
4 way plug boot, gray, enhanced length - - DTP4S-BT-EN
6 way plug boot, gray DT6S-BT DTM6S-BT -
6 way plug boot, black DT6S-BT-BK - -
8 way plug boot, gray DT8S-BT DTM8S-BT -
8 way plug boot, black DT8S-BT-BK DTM8S-BT-BK -
12 way plug boot, gray DT12S-BT DTM12S-BT -
12 way plug boot, black DT12S-BT-BK DTM12S-BT-BK -
12 way plug boot, gray, enhanced length DT12S-BT-EN - -
48 way plug boot, gray DT48S-BT - -
Boots
Boots provide a professional looking fi nishing touch for your Deutsch DT family connectors. Made of du-
rable plastisol, these slip-on boots are not only aesthetically appealing, but also provide increased protection
from dirt, paint overspray, and pressure washing. The plastisol boots are rated from -20° F to +212° F and
offer a slip-on design making installation quick and easy.
A STEP AHEAD
26
DT Family
Receptacle Backshells
Connector Style Strain
Relief
Tubing Size
(mm) P/N
DT04-2P 180° 6, 7.5, 8.5, and 10 1011-229-0205
180° X 6, 7.5, 8.5, and 10 1011-257-0205
90° 6, 7.5, 8.5, and 10 1011-230-0205
90° X 6, 7.5, 8.5, and 10 1011-258-0205
DT04-3P 180° 6, 7.5, 8.5, and 10 1011-233-0305
180° X 6, 7.5, 8.5, and 10 1011-261-0305
90° 6, 7.5, 8.5, and 10 1011-234-0305
90° X 6, 7.5, 8.5, and 10 1011-262-0305
DT04-4P 180° 6, 7.5, 8.5, and 10 1011-237-0405
180° X 6, 7.5, 8.5, and 10 1011-265-0405
90° 6, 7.5, 8.5, and 10 1011-238-0405
90° X 6, 7.5, 8.5, and 10 1011-266-0405
DT04-6P 180° 8.5, 10, and 13 1011-241-0605
180° X 8.5, 10, and 13 1011-269-0605
90° 8.5, 10, and 13 1011-242-0605
90° X 8.5, 10, and 13 1011-270-0605
DT04-08P* 180° 8.5, 10, and 13 1011-245-0805
90° 8.5, 10, and 13 1011-246-0805
DT04-12P* 180° 10, 13, and 17 1011-249-1205
90° 10, 13, and 17 1011-250-1205
Plug Backshells
Connector Style Strain
Relief
Tubing Size
(mm) P/N
DT06-2S 180° 6, 7.5, 8.5, and 10 1011-227-0205
180° X 6, 7.5, 8.5, and 10 1011-255-0205
90° 6, 7.5, 8.5, and 10 1011-228-0205
90° X 6, 7.5, 8.5, and 10 1011-256-0205
DT06-3S 180° 6, 7.5, 8.5, and 10 1011-231-0305
180° X 6, 7.5, 8.5, and 10 1011-259-0305
90° 6, 7.5, 8.5, and 10 1011-232-0305
90° X 6, 7.5, 8.5, and 10 1011-260-0305
DT06-4S 180° 6, 7.5, 8.5, and 10 1011-235-0405
180° X 6, 7.5, 8.5, and 10 1011-263-0405
90° 6, 7.5, 8.5, and 10 1011-236-0405
90° X 6, 7.5, 8.5, and 10 1011-264-0405
DT06-6S 180° 8.5, 10, and 13 1011-239-0605
180° X 8.5, 10, and 13 1011-267-0605
90° 8.5, 10, and 13 1011-240-0605
90° X 8.5, 10, and 13 1011-268-0605
DT06-08S* 180° 8.5, 10, and 13 1011-243-0805
90° 8.5, 10, and 13 1011-244-0805
DT06-12S* 180° 10, 13, and 17 1011-247-1205
90° 10, 13, and 17 1011-248-1205
Connector FP [N] FT [N]
DT04-2P / DT06-2S 50 / 50 50 / 10
DT04-3P / DT06-3S 50 / 50 50 / 50
DT04-4P / DT06-4S 50 / 50 50 / 25
DT04-6P / DT06-6S 50 / 50 50 / 30
DT04-08P* / DT06-08S* 50 / 50 50 / 35
DT04-12P* / DT06-12S* 50 / 50 50 / 40
90° 90°
FT
FP
FP
FT
Backshells
The Deutsch DT Series backshells are designed to
snap onto and mate with all standard (basic plug and
receptacles without modifi cations) DT Series connectors.
The rigid, durable backshells offer a high level of
protection and allow convoluted tubing to nest within
the rear of the backshell. Straight (180°) and right
angle (90°) versions and backshells with strain relief for
jacketed cable are also available.
The backshells are available for both standard plugs
and standard receptacles. Since they are designed to
work with the standard DT connectors, tests should be
conducted for fi t and function of a backshell being used
on any part with a modifi cation.
Pull Off Strength
A STEP AHEAD
27
DT Family
Mounting Clip Part Number Used On
(Receptacles)
Mounting
Direction Color/Material Hole O.D.
inches (mm)
1027-003-1200 DT 2, 3, 4, 6, 12
DTM, DTP (all) Straight Stainless steel .433 (11.0)
1027-005-1200 DT 2, 3, 4, 6, 12
DTM, DTP (all) Straight Stainless steel .512 (13.0)
1027-004-1200 DT 2, 3, 4, 6, 12
DTM, DTP (all) Straight Steel w/
zinc plating .512 (13.0)
1027-008-1200 DT 2, 3, 4, 6, 12
DTM, DTP (all) Side Steel w/
zinc plating .433 (11.0)
1027-013-1200 DT 2, 3, 4, 6, 12
DTM, DTP (all) Side Steel w/
zinc plating .323 (8.2)
1027-001-0800 DT 8 cavity only Straight Stainless steel .433 (11.0)
1027-006-0800 DT 8 cavity only Straight Stainless steel .512 (13.0)
1027-002-0800 DT 8 cavity only Straight Steel w/
zinc plating .512 (13.0)
1027-014-0800 DT 8 cavity only Straight Steel w/
zinc plating .323 (8.2)
1011-026-0205 DT 2, 3, 4, 6, 12
DTM, DTP (all) Straight Gray
plastic .200 (5.08)
1011-030-0205 DT 2, 3, 4, 6, 12
DTM, DTP (all) Straight Black
plastic ---
1011-310-0205*
*Connector removeable
with 50N of force
DT 2, 3, 4, 6, 12
DTM, DTP (all) Straight Black
plastic ---
1011-027-0805 DT 8 cavity only Straight Gray
plastic .200 (5.08)
Mounting Clips
Mounting clips are used to mount DT Series connectors. To meet design needs, the clips are available for several
confi gurations and in plastic or stainless steel.
A STEP AHEAD
28
DT Family
DTV Series Wedgelocks
Receptacle Plug
WV-18P Wedgelock for 18 way
receptacle WV-18S Wedgelock for 18 way plug
DTV Series Overview
Deutsch’s DTV Series connectors offer the same time tested reliability and performance
as the DT Series, with the added fl exibility of an 18 cavity fl anged design. Deutsch con-
tinues its tradition of providing an environmentally sealed connector to meet even your
toughest application needs.
DTV 06 - 18 S *
Series
Style
02 = Receptacle
06 = Plug
Confi guration
Key
A, B, C, or D
Contacts
P = Pin
S = Socket
Cavity
DTV Plug DTV Receptacle
Overall Length
A
Overall Height
B
Overall Width
C
Overall Length
D
Overall Height
E
Overall Width
F
18 1.405 (35.69) 1.059 (26.90) 1.450 (36.83) 2.495 (63.37) 1.786 (45.36) 3.194 (81.12)
Dimensions are for reference only.
DTV Series Part Numbering System
DTV Series Dimensions
Secondary Wedgelocks
E
FD
F
D
B
CA
C
A
A STEP AHEAD
29
DT Family
DTMH Series Overview
The DTMH is an environmentally sealed, high temperature connector capable of operat-
ing in temperatures -55° to +150°C. The DTMH accepts size 20 contacts and carries 7.5
amps each. The DTMH connectors feature an integrated TPA for easy assembly.
Cavity
DTMH Plug DTMH Receptacle
Overall Length
A
Overall Height
B
Overall Width
C
Overall Length
D
Overall Height
E
Overall Width
F
2 1.085 (27.56) .508 (12.90) .555 (14.10) 1.620 (41.15) .638 (16.21) .729 (18.52)
3 1.085 (27.56) .558 (14.17) .640 (16.26) 1.620 (41.16) .638 (16.21) .894 (22.71)
4 1.185 (30.10) .652 (16.56) .680 (17.27) 1.720 (43.69) .772 (19.61) .834 (21.18)
Dimensions are for reference only.
DTMH Series Dimensions
A
C
B
A
C
F
ED
F
D
DTMH0*-2**
2 size 20
DTMH0*-3**
3 size 20
DTMH0*-4**
4 size 20
DTMH Series Confi gurations
DTMH 04 - 2 P *
Series
Style
04 = Receptacle
06 = Plug
Confi guration
Key
A, B, C, or D
Contacts
P = Pin
S = Socket
DTMH Series Part Numbering System
A STEP AHEAD
30
DT Family
Cavity
DTMN Plug DTMN Receptacle
Overall Length
A
Overall Height
B
Overall Width
C
Overall Length
D
Overall Height
E
Overall Width
F
2 .950 (24.13) .346 (8.78) .370 (9.40) 1.198 (30.43) .334 (8.48) .444 (11.28)
3 .945 (24.00) .406 (10.31) .785 (19.93) 1.188 (30.18) .400 (10.16) .810 (20.56)
Dimensions are for reference only.
DTMN Series Dimensions
ED
F
B
A
C
A
C
DTMN Series Overview
The DTMN is a non-environmentally sealed connector. The DTMN is available in a 2 or 3
cavity connector and accepts size 20 contacts. The DTMN connector is designed to offer
Deutsch quality and reliability when a sealed connector is not required.
DTMN0*-2**
2 size 20
DTMN0*-3**
3 size 20
DTMN Series Confi gurations
DTMN 04 - 2 P
Series
Style
04 = Receptacle
06 = Plug
Contacts
P = Pin
S = Socket
Confi guration
DTMN Series Part Numbering System
A STEP AHEAD
31
DT Family
Step 1:
Grasp crimped contact ap-
proximately one inch behind
the contact barrel.
Step 2:
Hold connector with rear
grommet facing you.
Step 3:
Push contact straight into
connector grommet until a
click is felt. A slight tug will
confi rm that it is properly
locked in place.
Step 4:
Once all contacts are in
place, insert green wedge.
The green wedge will snap
into place.
How To Instructions
Contact Insertion
Step 1:
Remove green wedge using
needlenose pliers to pull
wedge straight out.
Step 2:
To remove the contacts,
gently pull wire backwards,
while at the same time
releasing the locking fi nger
by moving it away from the
contact with a screwdriver.
Step 3:
Hold the rear seal in place,
as removing the contact will
displace the seal.
Contact Removal
Note
Jiffy Splices
accept one
pin and one
socket.
Note
e
e
Ji
ff
y Splices
accept one
p
in and one
s
ocket.
Note
N
N
N
Note
ote
ote
No
No
oo
oo
tete
tete
NN
NN
NN
NN
t
t
NN
Note
The receptacle is
shown, use the
same procedure
for the plug.
Notice
Notice
