3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M MetPak HM Power Header
2 mm Type D, 176 Signal/4 Power Contacts, 8 Rows, Straight HM Series
Physical
Performance
Environmental
Insulation
Material: High Temperature Thermoplastic (LCP)
Flammability: UL 94V-0
Contact
Material: Copper Alloy
Plating: See Ordering Information
Marking: 3M Logo, Part Number, Revision, Date Code
Mechanical
Normal Force (Nominal): 0.57 N [ 58 g ] Signal, 0.98 N [ 100 g ] Power
Engagement Force (Nominal): 0.32 N [ 33 g ] Signal, 1.42 N [ 145 g ] Power
Separation Force (Nominal): 0.20 N [ 20 g ] Signal, 0.89 N [ 91 g ] Power
Wipe (Nominal, Shortest Contact): 2.67 mm [ 0.105 in. ] Signal, 1.93mm [ 0.076 in. ] Power
Durability: 250 cycles with TR40B plating (Lubricated)
Application: This module is suitable for stand-alone use
Electrical
Current Rating (Fully Loaded): 1 A at 70° C Signal, 8.25 A at 70° C Power
Insulation Resistance: 1 x 104 MΩ at 100 VDC
Withstanding Voltage: 750 VRMS
Temperature Rating: -55°C to +125°C
Process Rating: Maximum 260°C (per J-STD-020C)
Moisture Sensitivity Level: (per J-STD-020C)
TS-2020-03
Sheet 1 of 3
Date Modified: April 5, 2007
Modular/scalable format IEC 61076-4-101
Press-fit or solder tail versions
101 mated lines per linear inch
Four integrated 8.25 A power contacts
and guide pin
Ships with protective cap, which also serves
as an insertion tool
Integrated guide pin
End-to-end stackable with 8 row 3M™
MetPak™ HM and HSHM products
See Regulatory Information Appendix (RIA)
chemical compliance information
UL File No.: E68080 MetPak is a trademark of 3M Company.
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M MetPak HM Power Header
2 mm Type D, 176 Signal/4 Power Contacts, 8 Rows, Straight HM Series
ROW F
ROW E
ROW D
ROW C
ROW B
ROW A
ROW Z
Pin positions
1 2 3 4 5 6 7 8 9 10 11 P1 P2 15 16 17 18 19 20 21 22 23 24 25
DIM A = Pin mating length
DIM B = Tail length
Shown with protective caps*
* Caps to be removed after press-fit installation process
HM -HXXXXX-8XPX-XXXXX
REV X XXYY
18.00
.709
2.00
.079
2.00
.079
2.00
.079
2.00
.079
48.00
1.890
ROW G
ROW H
ROW I
21.40
.843
16.72
.658
5.00
.197
13.40
.528
DIM A
DIM B
Signal
contacts
15.15
.596
4.50
.177
1.50
.059
24.00
.945
49.85
1.963
P3 P4
2.00
.079 ESD pin tail length
ESD pin
Power tails (4 contacts 12 leads)
0 0.0 0.00
mm ±3 ±0.3 ±0.13
mm
[inch]
Tolerance Unless Noted
[ ] Dimensions for Reference Only
TS-2020-03
Sheet 2 of 3
HM - H220DPWR2 - 8BXX - XXXXX
Tail Style:
P = Press-fit tail
S = Solder tail
HM - H176DPWR1 - 8CXX - XXXXX
Standard configuration
DIM A = 5.3 mm for rows A through H
For non-standard configurations contact sales representative
(rows I and Z not loaded)
Tail Length (DIM B):
1 = 4.4 mm pin, 2.0 mm power
and 2.0 mm ESD
2 = 4.4 mm pin, 4.4 mm power
and 2.0 mm ESD
Plating Options:
(See Plating Chart)
Ordering Information
(rows I and Z loaded 8.3 mm mate length)
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M MetPak HM Power Header
2 mm Type D, 176 Signal/4 Power Contacts, 8 Rows, Straight HM Series
Recommended PCB hole mounting pattern
Plated thru holes
lO0.10 MAB
2.00
48.00
ABCDE A
1
2
3
4
5
6
7
8
9
10
11
15
16
17
18
19
20
21
22
23
24
25
FGHIZ
2.00
O DIM E 232X
1.508X
22.10
2.002X
23.90
24.00
5.00
12.00
O DIM F 1X
lO0.05 MAB
Plated thru holes
1.50
18.00
B
TS-2020-03
Sheet 3 of 3
Plating
Suffix
Press-Fit
Terminations
Solder Tail
Terminations
TG30 (RIA E2 & C2 apply) (RIA E3 & C2 apply)
TR40B (RIA E2 & C2 apply) (RIA E3 & C2 apply)
Plating Chart
Plating Composition
0.76 µm [30 µ"] Min. Au Contact Area
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.127 µm [5 µ"] Min. Hard Au over
1.02 µm [40 µ"] Min. Pd/Ni over
0.10 µm [4 µ"] Min. Pd Strike Contact Area
2.54 µm [100µ"] Min SnPb Terminal Area
1.27 µm [50 µ"] Min. Ni all over
(Lubricated Contact Area)
DIM FINISHED HOLE DIA. "D" Cu. THICKNESS SnPb THICKNESS DRILLED HOLE DIA.
E 0.550 - 0.650 [.0217 - .0256] 0.025 - 0.045 [.0010 - .0018] 0.008 - 0.018 [.0003 - .0007] 0.686 - 0.727 [.0270 - .0286]
F 0.690 - 0.790 [.0270 - .0310] 0.025 - 0.045 [.0010 - .0018] 0.008 - 0.018 [.0003 - .0007] 0.810 - 0.860 [.0318 - .0339]
HOLE PLATING TABLE mm [in.]
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/ECmeans that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/ECmeans that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon
information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217-B
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does not contain any of the following substances in excess of the following maximum
concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise
stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by
third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
20
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does contain a substance, as detailed in the chart below, in excess of the following
maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless
otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform
with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in
accordance with the product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in
writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to
replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any
indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/225-5373
www.3M.com/interconnects RIA-2217-B
© 3M 2007
Name and Content of Hazardous Substances or Elements