LM2703 www.ti.com SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 LM2703 Micropower Step-Up DC/DC Converter with 350mA Peak Current Limit Check for Samples: LM2703 FEATURES DESCRIPTION * * * * * * * The LM2703 is a micropower step-up DC/DC in a small 5-lead SOT-23 package. A current limited, fixed off-time control scheme conserves operating current resulting in high efficiency over a wide range of load conditions. The 22V switch allows for output voltages as high as 21V. The low 400ns off-time permits the use of tiny, low profile inductors and capacitors to minimize footprint and cost in space-conscious portable applications. The LM2703 is ideal for LCD panels requiring low current and high efficiency as well as white LED applications for cellular phone back-lighting. The LM2703 can drive up to 4 white LEDs from a single Li-Ion battery. 1 2 350mA, 0.7, Internal Switch Uses Small Surface Mount Components Adjustable Output Voltage up to 21V 2.2V to 7V Input Range Input Undervoltage Lockout 0.01A Shutdown Current Small 5-Lead SOT-23 Package APPLICATIONS * * * * * LCD Bias Supplies White LED Back-Lighting Handheld Devices Digital Cameras Portable Applications Typical Application Circuit L 10 PH VIN = Li-Ion 5 1 SW VIN CIN 4.7 PF 4 20V 15 mA D R1 510k LM2703 3 FB SHDN GND 2 COUT 1 PF R2 33k CIN: Taiyo Yuden Ceramic COUT: Taiyo Yuden Ceramic L: Coilcraft DT1608C-103 or Murata LQY33PN100M02 (low profile) D: Motorola MBRM130LT3 Figure 1. Typical 20V Application 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2013, Texas Instruments Incorporated LM2703 SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 www.ti.com Connection Diagram Top View SW VIN GND FB SHDN The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junctionto-ambient thermal resistance, JA, and the ambient temperature, TA. See the Electrical Characteristics table for the thermal resistance. The maximum allowable power dissipation at any ambient temperature is calculated using: PD (MAX) = (TJ(MAX) - TA)/JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature. Figure 2. SOT23-5 TJmax = 125C, JA = 220C/W PIN DESCRIPTIONS Pin Name 1 SW Power Switch input. 2 GND Ground. 3 FB 4 SHDN 5 VIN Function Output voltage feedback input. Shutdown control input, active low. Analog and Power input. SW (Pin 1): Switch Pin. This is the drain of the internal NMOS power switch. Minimize the metal trace area connected to this pin to minimize EMI. GND (Pin 2): Ground Pin. Tie directly to ground plane. FB (Pin 3): Feedback Pin. Set the output voltage by selecting values for R1 and R2 using: R1 = R2 VOUT -1 1.237V (1) Connect the ground of the feedback network to an AGND plane which should be tied directly to the GND pin. SHDN (Pin 4): Shutdown Pin. The shutdown pin is an active low control. Tie this pin above 1.1V to enable the device. Tie this pin below 0.3V to turn off the device. VIN (Pin 5): Input Supply Pin. Bypass this pin with a capacitor as close to the device as possible. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 LM2703 www.ti.com SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 Absolute Maximum Ratings (1) (2) VIN 7.5V SW Voltage 22.5V FB Voltage 2V SHDN Voltage 7.5V Maximum Junction Temp. TJ (3) 150C Lead Temperature (Soldering 10 sec.) 300C Vapor Phase (60 sec.) 215C Infrared (15 sec.) 220C (4) ESD Ratings Human Body Model Machine Model (5) (1) 2kV 200V Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended to be functional, but device parameter specifications may not be ensured. For ensured specifications and test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, JA, and the ambient temperature, TA. See the Electrical Characteristics table for the thermal resistance. The maximum allowable power dissipation at any ambient temperature is calculated using: PD (MAX) = (TJ(MAX) - TA)/JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature. The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. ESD susceptibility using the machine model is 150V for SW pin. (2) (3) (4) (5) Operating Conditions Junction Temperature (1) -40C to +125C Supply Voltage 2.2V to 7V SW Voltage Max. (1) 22V All limits ensured at room temperature and at temperature extremes. All room temperature limits are 100% production tested or ensured through statistical analysis. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Electrical Characteristics Specifications in standard type face are for TJ = 25C and those in boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C). Unless otherwise specified. VIN =2.2V. Symbol IQ Parameter Min Conditions (1) Typ Max 40 70 (2) (1) Device Disabled FB = 1.3V Device Enabled FB = 1.2V 235 300 Shutdown SHDN = 0V 0.01 2.5 Units A VFB FeedbackTrip Point 1.189 1.237 1.269 V ICL Switch Current Limit 275 260 350 400 400 mA 30 120 nA 7.0 V IB FB Pin Bias Current VIN Input Voltage Range RDSON Switch RDSON 0.7 TOFF Switch Off Time 400 (1) (2) (3) FB = 1.23V (3) 2.2 1.6 ns All limits ensured at room temperature and at temperature extremes. All room temperature limits are 100% production tested or ensured through statistical analysis. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Typical numbers are at 25C and represent the most likely norm. Feedback current flows into the pin. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 3 LM2703 SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 www.ti.com Electrical Characteristics (continued) Specifications in standard type face are for TJ = 25C and those in boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C). Unless otherwise specified. VIN =2.2V. Symbol ISD Parameter SHDN Pin Current Typ Max SHDN = VIN, TJ = 25C 0 80 SHDN = VIN, TJ = 125C 15 SHDN = GND 0 Conditions Min (1) (2) (1) Units nA IL Switch Leakage Current VSW = 22V 0.05 UVP Input Undervoltage Lockout ON/OFF Threshold 1.8 V VFB Hysteresis Feedback Hysteresis 8 mV SHDN Threshold SHDN low JA Thermal Resistance 4 0.7 SHDN High 1.1 0.7 220 Submit Documentation Feedback 5 0.3 A V C/W Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 LM2703 www.ti.com SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 Typical Performance Characteristics Enable Current vs VIN (Part Switching) Disable Current vs VIN (Part Not Switching) Figure 3. Figure 4. Efficiency vs Load Current Efficiency vs Load Current 95 V OUT = 20V V IN = 4.2V 85 EFFICIENCY (%) V IN = 3.3V 75 V IN = 2.5V 65 55 45 35 0.05 2 6 10 14 18 22 26 LOAD CURRENT (mA) Figure 5. Figure 6. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 5 LM2703 SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) 6 Efficiency vs Load Current SHDN Threshold vs VIN Figure 7. Figure 8. Switch Current Limit vs VIN Switch RDSON vs VIN Figure 9. Figure 10. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 LM2703 www.ti.com SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 Typical Performance Characteristics (continued) FB Trip Point and FB Pin Current vs Temperature 12.20 50 12.15 124 45 40 123 35 122 30 nA 25 121 20 120 -40 -20 0 20 40 60 15 80 100 120 OUTPUT VOLTAGE (V) FEEDBACK TRIP POINT (V) V 55 FEEDBACK BIAS CURRENT (nA) 125 Output Voltage vs Load Current C = 1uF OUT V = 12V OUT V 12.10 12.05 V IN = 2.5V V 11.95 IN = 3.3V V 11.90 11.85 0.05 2 IN = 5V 6 10 14 18 22 26 30 38 55 75 LOAD CURRENT (mA) Figure 12. Step Response Figure 13. = 4.2V 12.00 JUNCTION TEMPERATURE (C) Figure 11. VOUT = 20V, VIN = 2.5V 1) Load, 1mA to 10mA to 1mA, DC 2) VOUT, 200mV/div, AC 3) IL, 200mA/div, DC T = 50s/div IN Start-Up/Shutdown VOUT = 20V, VIN = 2.5V 1) SHDN, 1V/div, DC 2) IL, 200mA/div, DC 3) VOUT, 20V/div, DC T = 400s/div RL = 1.8k Figure 14. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 7 LM2703 SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 www.ti.com OPERATION V C V IN 5 SW IN R1 50k V R2 50k C OUT Enable FB 3 R OUT Q1 Q2 10x + F1 1 V Enable Comp OUT + R D L IN CL Comp F2 - R3 30k Current Sensing Circuitry CL Adjust R4 140k 400ns One Shot Driver Logic Under Voltage Lockout 4 2 GND SHDN Figure 15. LM2703 Block Diagram VOUT = 20V, VIN = 2.5V 1) VSW, 20V/div, DC 2) Inductor Current, 200mA/div, DC 3) VOUT, 200mV/div, AC T = 4s/div Figure 16. Typical Switching Waveform The LM2703 features a constant off-time control scheme. Operation can be best understood by referring to Figure 15 and Figure 16. Transistors Q1 and Q2 and resistors R3 and R4 of Figure 15 form a bandgap reference used to control the output voltage. When the voltage at the FB pin is less than 1.237V, the Enable Comp in Figure 15 enables the device and the NMOS switch is turned on pulling the SW pin to ground. When the NMOS switch is on, current begins to flow through inductor L while the load current is supplied by the output capacitor COUT. Once the current in the inductor reaches the current limit, the CL Comp trips and the 400ns One Shot turns 8 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 LM2703 www.ti.com SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 off the NMOS switch.The SW voltage will then rise to the output voltage plus a diode drop and the inductor current will begin to decrease as shown in Figure 16. During this time the energy stored in the inductor is transferred to COUT and the load. After the 400ns off-time the NMOS switch is turned on and energy is stored in the inductor again. This energy transfer from the inductor to the output causes a stepping effect in the output ripple as shown in Figure 16. This cycle is continued until the voltage at FB reaches 1.237V. When FB reaches this voltage, the enable comparator then disables the device turning off the NMOS switch and reducing the Iq of the device to 40uA. The load current is then supplied solely by COUT indicated by the gradually decreasing slope at the output as shown in Figure 16. When the FB pin drops slightly below 1.237V, the enable comparator enables the device and begins the cycle described previously. The SHDN pin can be used to turn off the LM2703 and reduce the Iq to 0.01A. In shutdown mode the output voltage will be a diode drop lower than the input voltage. APPLICATION INFORMATION INDUCTOR SELECTION The appropriate inductor for a given application is calculated using the following equation: L= VOUT - VIN(min) + VD ICL TOFF (2) where VD is the schottky diode voltage, ICL is the switch current limit found in the Typical Performance Characteristics section, and TOFF is the switch off time. When using this equation be sure to use the minimum input voltage for the application, such as for battery powered applications. For the LM2703 constant-off time control scheme, the NMOS power switch is turned off when the current limit is reached. There is approximately a 200ns delay from the time the current limit is reached in the NMOS power switch and when the internal logic actually turns off the switch. During this 200ns delay, the peak inductor current will increase. This increase in inductor current demands a larger saturation current rating for the inductor. This saturation current can be approximated by the following equation: IPK = ICL + VIN(max) L 200ns (3) Choosing inductors with low ESR decrease power losses and increase efficiency. Care should be taken when choosing an inductor. For applications that require an input voltage that approaches the output voltage, such as when converting a Li-Ion battery voltage to 5V, the 400ns off time may not be enough time to discharge the energy in the inductor and transfer the energy to the output capacitor and load. This can cause a ramping effect in the inductor current waveform and an increased ripple on the output voltage. Using a smaller inductor will cause the IPK to increase and will increase the output voltage ripple further. This can be solved by adding a 4.7pF capacitor across the RF1 feedback resistor (Figure 15) and slightly increasing the output capacitor. A smaller inductor can then be used to ensure proper discharge in the 400ns off time. DIODE SELECTION To maintain high efficiency, the average current rating of the schottky diode should be larger than the peak inductor current, IPK. Schottky diodes with a low forward drop and fast switching speeds are ideal for increasing efficiency in portable applications. Choose a reverse breakdown of the schottky diode larger than the output voltage. CAPACITOR SELECTION Choose low ESR capacitors for the output to minimize output voltage ripple. Multilayer ceramic capacitors are the best choice. For most applications, a 1F ceramic capacitor is sufficient. For some applications a reduction in output voltage ripple can be achieved by increasing the output capacitor. Local bypassing for the input is needed on the LM2703. Multilayer ceramic capacitors are a good choice for this as well. A 4.7F capacitor is sufficient for most applications. For additional bypassing, a 100nF ceramic capacitor can be used to shunt high frequency ripple on the input. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 9 LM2703 SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 www.ti.com LAYOUT CONSIDERATIONS The input bypass capacitor CIN, as shown in Figure 1, must be placed close to the IC. This will reduce copper trace resistance which effects input voltage ripple of the IC. For additional input voltage filtering, a 100nF bypass capacitor can be placed in parallel with CIN to shunt any high frequency noise to ground. The output capacitor, COUT, should also be placed close to the IC. Any copper trace connections for the Cout capacitor can increase the series resistance, which directly effects output voltage ripple. The feedback network, resistors R1 and R2, should be kept close to the FB pin to minimize copper trace connections that can inject noise into the system. The ground connection for the feedback resistor network should connect directly to an analog ground plane. The analog ground plane should tie directly to the GND pin. If no analog ground plane is available, the ground connection for the feedback network should tie directly to the GND pin. Trace connections made to the inductor and schottky diode should be minimized to reduce power dissipation and increase overall efficiency. L 10 PH VIN 2.5V-4.2V D 5 1 VIN SW CIN 4.7 PF Ceramic COUT 1 PF Ceramic LM2703 >1.1V 0V 4 SHDN GND FB 3 2 R2 82: CIN: Taiyo Yuden Ceramic COUT: Taiyo Yuden Ceramic L: Coilcraft DT1608C-103 or Murata LQY33PN100M02 (low profile) D: Motorola MBRM130LT3 Figure 17. White LED Application Figure 18. Li-Ion 5V Application 10 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 LM2703 www.ti.com SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 L 10PH VIN 2.54.2V 5 1 VIN CIN 4 4.7PF 12V 22 mA D R1 240k SW COUT 1PF LM2703 3 FB SHDN R2 27k GND 2 Figure 19. Li-Ion 12V Application L 10PH VIN 5V 5 1 VIN CIN 4 4.7PF 12V 70 mA D SW R1 240k COUT 4.7PF LM2703 3 FB SHDN GND 2 R2 27k Figure 20. 5V to 12V Application Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 11 LM2703 SNVS172F - FEBRUARY 2002 - REVISED MAY 2013 www.ti.com REVISION HISTORY Changes from Revision E (May 2013) to Revision F * 12 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 11 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: LM2703 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM2703MF-ADJ NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 85 S48B LM2703MF-ADJ/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 S48B LM2703MFX-ADJ/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 S48B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LM2703MF-ADJ SOT-23 DBV 5 1000 178.0 8.4 LM2703MF-ADJ/NOPB SOT-23 DBV 5 1000 178.0 LM2703MFX-ADJ/NOPB SOT-23 DBV 5 3000 178.0 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2703MF-ADJ SOT-23 DBV 5 1000 210.0 185.0 35.0 LM2703MF-ADJ/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM2703MFX-ADJ/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated