IDT74FCT3807D/E 3.3V CMOS 1-TO-10 CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE 3.3V CMOS 1-TO-10 CLOCK DRIVER DESCRIPTION: FEATURES: * * * * * * * * * * * * * IDT74FCT3807D/E The FCT3807 is a 3.3V clock driver built using advanced CMOS technology. This low skew clock driver offers 1:10 fanout. The large fanout from a single input reduces loading on the preceding driver and provides an efficient clock distribution network. Multiple power and grounds reduce noise. Typical applications are clock and signal distribution. Advanced CMOS Technology Guaranteed low skew < 100ps (max.) Very low duty cycle distortion< 250ps (max.) High speed propagation delay< 2ns (max.) Very low CMOS power levels TTL compatible inputs and outputs 1:10 fanout Maximum output rise and fall time < 1ns (max.) Low input capacitance: 3pF typical VCC = 3.3V 0.3V Inputs can be driven from 3.3V or 5V components Operating frequency up to 166MHz Available in SSOP, QSOP, and TSSOP packages NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 PIN CONFIGURATION FUNCTIONAL BLOCK DIAGRAM O1 O2 O3 O4 O5 IN O6 IN 1 20 VCC GND 2 19 O10 O1 3 18 O9 VCC 4 17 GND O2 5 16 O8 GND 6 15 VCC O3 7 14 O7 VCC 8 13 GND O4 9 12 O6 10 11 O5 GND O7 SSOP/ QSOP/ TSSOP TOP VIEW O8 O9 O10 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE DECEMBER 2009 1 c 2006 Integrated Device Technology, Inc. DSC-5865/17 IDT74FCT3807D/E 3.3V CMOS 1-TO-10 CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE CAPACITANCE (TA = +25OC, f = 1.0MHz) ABSOLUTE MAXIMUM RATINGS(1) Parameter(1) Max Unit Symbol Conditions Typ. Max. Unit Input Power Supply Voltage -0.5 to +4.6 V CIN Input Capacitance VIN = 0V 3 4 pF VI Input Voltage -0.5 to +5.5 V COUT Output Capacitance VOUT = 0V -- 6 pF VO Output Voltage -0.5 to VCC+0.5 V TJ Junction Temperature 150 C TSTG Storage Temperature -65 to +165 C Symbol VCC Description NOTE: 1. This parameter is measured at characterization but not tested. PIN DESCRIPTION NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Pin Names Description IN Input Ox Outputs POWER SUPPLY CHARACTERISTICS Symbol Test Conditions(1) Parameter ICCQ Quiescent Power Supply Current ICC ICCD Min. Typ.(2) Max. Unit -- 0.1 30 A VCC = Max. VIN = GND or VCC Power Supply Current per Input HIGH VCC = Max. VIN = VCC - 0.6V -- 45 300 A Dynamic Power Supply Current VCC = Max. VIN = VCC -- 80 120 A/MHz per Output(3) CL = 15pF VIN = GND 125 150 125 150 -- 155 195 -- 160 195 All Outputs Toggling IC Total Power Supply Current(4) VCC = Max. VIN = VCC CL = 15pF VIN = GND All Outputs Toggling VIN = VCC -0.6V fi = 133MHz VIN = GND VCC = Max. VIN = VCC CL = 15pF VIN = GND All Outputs Toggling VIN = VCC -0.6V fi = 166MHz VIN = GND mA NOTES: 1. 2. 3. 4. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. Typical values are at VCC = 3.3V, +25C ambient. This parameter is not directly testable, but is derived for use in Total Power Supply calculations. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fi) ICC = Quiescent Current ICC = Power Supply Current for a TTL High Input (VIN = VCC -0.6V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fi = Input Frequency 2 IDT74FCT3807D/E 3.3V CMOS 1-TO-10 CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified Industrial: TA = -40C to +85C, VCC = 3.3V 0.3V Symbol Parameter Test Conditions(1) Min. Typ.(2) Max. Unit VIH Input HIGH Level 2 -- 5.5 V VIL Input LOW Level -0.5 -- 0.8 V IIH Input HIGH Current -- -- 1 A IIL VIK VCC = Max. VI = 5.5V Input LOW Current VCC = Max. VI = GND Clamp Diode Voltage VCC = Min., IIN = -18mA -- -- 1 -- -0.7 -1.2 V 1.5V(3,4) -45 -75 -180 mA 50 92 200 mA -60 IODH Output HIGH Current VCC = 3.3V, VIN = VIH or VIL, VO = IODL Output LOW Current VCC = 3.3V, VIN = VIH or VIL, VO = 1.5V(3,4) IOS VOH VOL Short Circuit Current Output HIGH Voltage Output LOW Voltage VCC = Max., VO = GND(3,4) -135 -240 mA V VCC = Min. IOH = -12mA 2.4(5) 3 -- VIN = VIH or VIL IOH = -100A VCC - 0.2 -- -- VCC = Min. IOL = 12mA -- 0.3 0.5 VIN = VIH or VIL IOL = 100A -- -- 0.2 NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3, 25C ambient. 3. This parameter is guaranteed but not tested. 4. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 5. VOH = VCC - 0.6V at rated current. 3 V IDT74FCT3807D/E 3.3V CMOS 1-TO-10 CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE SWITCHING CHARACTERISTICS OVER OPERATING RANGE - 3807D (3,4) Symbol tPLH Parameter Propagation Delay Conditions(1) Min.(2) Max. Unit CL = 15pF 1 2.5 ns f 133MHz tPHL tR Output Rise Time (0.8V to 2V) -- 1 ns tF Output Fall Time (2V to 0.8V) -- 1 ns tSK(O) Same device output pin-to-pin skew(5) -- 250 ps tSK(P) Pulse skew(6) -- 250 ps tSK(PP) Part to part skew(7) -- 550 ps Input Frequency -- 133 MHz fMAX SWITCHING CHARACTERISTICS OVER OPERATING RANGE - 3807E (3,4) Symbol tPLH Parameter Propagation Delay Conditions(1,8) Min.(2) Max. Unit CL = 15pF 0.5 2 ns f 166MHz tPHL tR Output Rise Time (0.8V to 2V) -- 1 ns tF Output Fall Time (2V to 0.8V) -- 1 ns tSK(O) Same device output pin-to-pin skew(5) -- 100 ps tSK(P) Pulse skew(6) -- 250 ps tSK(PP) Part to part skew(7) -- 550 ps Input Frequency -- 166 MHz fMAX NOTES: 1. See test circuits and waveforms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. tPLH, tPHL, tSK(P), and tSK(O) are production tested. All other parameters guaranteed but not production tested. 4. Propagation delay range indicated by Min. and Max. limit is due to VCC, operating temperature and process parameters. These propagation delay limits do not imply skew. 5. Skew measured between all outputs under identical transitions and load conditions. 6. Skew measured is difference between propagation delay times tPHL and tPLH of same output under identical load conditions. 7. Part to part skew for all outputs given identical transitions and load conditions at identical VCC levels and temperature. 8. Airflow of 1m/s is recommended for frequencies above 133MHz. 4 IDT74FCT3807D/E 3.3V CMOS 1-TO-10 CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS TEST CONDITIONS VCC Symbol VCC = 3.3V 0.3V Unit CL 15 pF RT ZOUT of pulse generator t R / tF 1 (0V to 3V or 3V to 0V) ns VIN VOUT Pulse Generator D.U.T. 15pF DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. tR / tF = Rise/Fall time of the input stimulus from the Pulse Generator. RT CL CL = 15pF Circuit TEST WAVEFORMS 3V 1.5V INPUT INPUT 0V tPLH tPLH1 tPHL1 tPHL VOH 2.0V 0.8V OUTPUT 1.5V VOL OUTPUT 1 tSK(o) 1.5V tSK(o) VOL VOH 1.5V VOL OUTPUT 2 tF tR 3V 1.5V 0V VOH tPLH2 tPHL2 tSK(o) = |tPLH2 - tPLH1| or |tPHL2 - tPHL1| Propagation Delay Output Skew - tSK(O) 3V 1.5V 0V INPUT tPLH tPHL OUTPUT VOH 1.5V VOL INPUT tPLH1 tPHL1 VOH 1.5V VOL PACKAGE 1 OUTPUT tSK(PP) tSK(PP) tSK(p) = |tPHL - tPLH| PACKAGE 2 OUTPUT Pulse Skew - tSK(P) 3V 1.5V 0V tPLH2 tPHL2 VOH 1.5V VOL tSK(PP) = |tPLH2 - tPLH1| or |tPHL2 - tPHL1| Part-to-Part Skew - tSK(PP) Part-to-Part Skew is for the same package and speed grade. 5 IDT74FCT3807D/E 3.3V CMOS 1-TO-10 CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDT74FCT XXXX Device Type X Package X Process I -40C to +85C (Industrial) PY PYG Q QG PG PGG Shrink Small Outline IC SSOP - Green Quarter-size Small Outline IC QSOP - Green Thin Shrink Small Outline IC TSSOP - Green 3807D 3807E 3.3V CMOS 1-to-10 Clock Driver NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 6 for Tech Support: clockhelp@idt.com