VTC1-A23A-10M000 - Vectron International

Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

VTC1 series

Voltage Controlled Temperature Compensated Crystal Oscillator

The VTC1, VCTXCO

Features

• Clipped Sine Wave or Square Wave Output

• Output Frequencies to 40 MHz

• Fundamental Crystal Design

• Optional VCXO function available

• Gold over nickel contact pads

• Hermetically Sealed Ceramic SMD package

• Product is compliant to RoHS directive

and fully compatible with lead free assembly

Applications

• Wireless Communications

• Base Stations

• Point to point radios

• Broadband Access

• Test Equipment

• Handsets

Description

Vectron’s VTC1 Temperature Compensated

Crystal Oscillator (TCXO) is a quartz stabilized,

clipped sinewave output or CMOS squarewave,

temperature compensated oscillator, operating off

either 2.8, 3.0, 3.3 or 5.0 volt supply.

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Performance Characteristics

Table 1. Electrical Performance for the Clipped Sine Wave Output Option

Parameter Symbol

Min Typical Maximum Units

Frequency fO 10.000 40.000 MHz

Typical Supply Voltage

Ordering option, see last page 2.8V, 3.0V, 3.3V or 5.0V

Supply Current

10.000 MHz to < 15.000 MHz

15.000 MHz to < 26.00 MHz

26.000 MHz to 40.000 MHz

IDD

1.5

2.0

2.5

Output Level 2 Vp/p 0.8 V

Output Load 10K II 10pf

Control Voltage Impedance ZVc 1 Mohm

Control Voltage to reach pull

All options (5.0, 3.3,3.0 and 2.8V)

0.5

2.5 V

Pull Range

Ordering option, see last page TPR ±5, ±8, ±10, ±15 or ±20 ppm

Temperature Stability

Ordering option, see last page. ±0.5 to ±5.0 ppm

Initial Accuracy, “No Adjust” option ±0.5 ppm

Power Supply Stability ±0.2 ppm

Load Stability ±0.2 ppm

Aging ±1.0 ppm/year

Operating temperature

Ordering option, see last page 0/55, -10/60, -20/70, -30/80, -40/85 °C

Phase Noise, 12.800 MHz

10 Hz offset

100 Hz offset

1 kHz offset

10 kHz offset

100 kHz offset

-85

-115

-130

-143

-152

dBc/Hz

Start-up time 2 ms

1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.

2. Output is AC coupled.

VTC1 Data sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Table 2. Electrical Performance for the CMOS Output Option

Parameter Symbol

Min Typical Maximum Units

Frequency fO 10.000 40.000 MHz

Supply Voltage 3.3V±10% VDC

Maximum Supply Voltage 7 VDC

Supply Current IDD 10.0 mA

Output Level 2

Logic High

Logic Low

Drive High

Drive Low

VOH

VOL

IOH

IOL

0.9*VDD

0.1*VDD

-4

Output Load 15pf

Duty Cycle, @ 50% 45/55 %

Control Voltage Impedance ZVc 100 Kohm

Control Voltage to reach pull 0.5 2.5 V

Pull Range

Ordering option, see last page TPR ±5, ±8, ±10 ppm

Temperature Stability

Ordering option, see last page. ±0.5 to ±5.0 ppm

Initial Accuracy, “No Adjust” option ±0.5 ppm

Power Supply Stability ±0.3 ppm

Load Stability ±0.2 ppm

Aging ±1.0 ppm/year

Operating temperature

Ordering option, see last page 0/55, -10/60, -20/70, -30/80, -40/85 °C

Phase Noise, 12.800MHz

10 Hz offset

100 Hz offset

1 kHz offset

10 kHz offset

100 kHz offset

-93

-123

-147

-155

-158

dBc/Hz

Start-up time 2 ms

1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.

2. Output is DC coupled.

VTC1 Data sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Figure 1. Typical Phase Noise Plot, Clipped Sine Wave

Figure 2. Clipped Sine Wave Output

VTC1 Data sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

VCXO Functional Description

VCXO Feature: The VTC1 can be ordered with a VCXO function for applications were it will be used in a

PLL, or the output frequency needs fine tune adjustments. This is high impedance, 1 Mohm, input and can

be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left floating on

the VCXO optional devices.

“No Adjust” Feature: In applications were the VTC1 will be not be used in a PLL, or the output frequency

does not fine tune adjustments, the best device to use would be a VTC1-x0xxx. By using the “no adjust”

option, the circuit is simplified as Vc does not need to adjusted or set to a predetermined voltage and pin 1

should be grounded or left open (but not set to a voltage such as the supply).

Outline Diagrams, Pad Layout and Pin Out

Table 3. Pinout

Pin # Symbol Function

1 N/C or

VC No Connect (VTC1-x0xx)

or VCXO Control Voltage

2 GND Electrical and Case Ground

3 fO Output Frequency

4 VDD Supply Voltage

NOTE: Additional pads are used to program and adjust the TCXO during manufacturing and should be left

open; do not terminate these to the supply voltage. Some designs do not include these additional pads.

Contact Pads are gold over nickel

Figure 3, Package drawing

VTC1 Data sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

GFJ

Tape and Reel

Table 4. Tape and Reel Dimensions (mm)

Tape Dimensions Reel Dimensions # Per

Product A B C D E F G H I J K L Reel

VTC1 16 7.5 1.5 4 8 1.5 20.2 13 60 2 16.4 180 1000

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional

operation is not implied at these or any other conditions in excess of conditions represented in the

operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may

adversely affect device reliability.

Table 5. Absolute Maximum Ratings

Parameter Symbol Ratings Unit

Storage Temperature Tstorage -55/125 °C

Reliability

The VTC1 qualification tests have included:

Table 6. Environnemental Compliance

Parameter Conditions

Mechanical Shock MIL-STD-883 Method 2002

Mechanical Vibration MIL-STD-883 Method 2007

Temperature Cycle MIL-STD-883 Method 1010

Solderability MIL-STD-883 Method 2003

Gross and Fine Leak MIL-STD-883 Method 1014

Resistance to Solvents MIL-STD-883 Method 2015

VTC1 Data Sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com

Handling Precautions

Although ESD protection circuitry has been designed into the the VTC1, proper precautions should be taken

when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for

ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit

parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a

standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be

used for comparison purposes.

Table 7. ESD Ratings

Model Minimum Conditions

Human Body Model 1000 MIL-STD-883 Method 3115

Charged Device Model 1500 JESD 22-C101

Suggested IR profile

Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions,

Table 7 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C.

Table 8. Reflow Profile (IPC/JEDEC J-STD-020B)

Parameter Symbol Value

PreHeat Time t S 150 sec Min, 200 sec Max

Ramp Up R UP 3 oC/sec Max

Time Above 217 oC t L 60 sec Min, 150 sec Max

Time To Peak Temperature t AMB-P 480 sec Max

Time At 260 oC (max) t P 10 sec Max

Time At 240 °C (max) tp2 60 sec Max

Ramp Down R DN 6 oC/sec Max

VTC1 Data Sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com

Ordering Information

Table 9. Standard Frequency List

10.000 10.0001355 10.001355 10.240 10.245 12.250 11.0592 11.2896

12.000 12.288 12.352 12.500 12.504 12.580 12.582912 12.600

12.688375 12.800 13.000 13.560 14.000 14.318 14.400 14.500

14.5888 14.617188 14.7456 14.850 15.000 15.359865 15.360 16.000

16.034950 16.320 16.3676 16.367667 16.36770 16.384 16.368 16.580

16.777216 16.800 17.500 18.000 18.414 18.432 18.601 19.000

19.200 19.440 19.680 19.800 20.000 20.250 20.480 20.91646

21.250 22.000 22.368 23.090 24.000 24.5535 24.576 24.8064

25.000 25.48828 26.000 32.000 33.000 38.400 40.000

VTC1 - -

Product Family Output Frequency

TCXO, 5x7 In MHz

Voltage Options Temperature Options

A: +5.0 Vdc ±5%, Clipped Sine Output A: 0 to 55°C

B: +3.3 Vdc ±5%, Clipped Sine Output B: -10 to 60°C

C: +3.0 Vdc ±5%, Clipped Sine Output C: -20 to 70°C

D: +2.8 Vdc ±5%, Clipped Sine Output D: -30 to 80°C

J: +3.3 Vdc ±10%, CMOS Output E: -40 to 85°C

Pulling Range

0: Fixed TCXO, no adjust Stability Options

1: ±5ppm A: ±0.5ppm

2: ±8ppm 1: ±1.0ppm

3: ±10ppm B: ±1.5ppm

4: ±15ppm 2: ±2.0ppm

5: ±20ppm C: ±2.5ppm

3: ±3.0 ppm

Note: Not all combinations are available: D: ±3.5ppm

±0.5 ppm is available over 0 to 55 °C only 4: ±4.0ppm

±1.0 ppm to ±5.0 ppm is available on all temperature ranges 5: ±5.0ppm

www.vectron.com

January 10, 2006

For Additional Information, Please Contact:

USA: Vectron International • 267 Lowell Road, Hudson, NH 03051

• Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON

EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany •

Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281

ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd.,

WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131

•Tel: 8621 50480777 • Fax: 8621 50481881

0 C 10M000