TS912, TS912A, TS912B Rail-to-rail CMOS dual operational amplifier Features Rail-to-rail input and output voltage ranges Single (or dual) supply operation from 2.7 to 16 V Extremely low input bias current: 1 pA typ. Low input offset voltage: 2 mV max. Specified for 600 and 100 loads Low supply current: 200 A/amplifier (VCC = 3 V) Latch-up immunity ESD tolerance: 3 kV Spice macromodel included in this specification N DIP-8 (Plastic package) D SO-8 (Plastic micropackage) Pin connections (top view) Description The TS912 is a rail-to-rail CMOS dual operational amplifier designed to operate with a single or dual supply voltage. Output 1 1 Inverting Input 1 2 - Non-inverting Input 1 3 + VCC 4 The input voltage range Vicm includes the two supply rails VCC+ and VCC-. 8 VCC + 7 Output 2 - 6 Inverting Input 2 + 5 Non-inverting Input 2 The output reaches VCC- +30 mV, VCC+ -40 mV, with RL = 10 k and VCC- +300 mV, VCC+ 400 mV, with RL = 600 . This product offers a broad supply voltage operating range from 2.7 to 16 V and a supply current of only 200 A/amp (VCC = 3 V). Source and sink output current capability is typically 40 mA (at VCC = 3 V), fixed by an internal limitation circuit. February 2010 Doc ID 2325 Rev 6 1/20 www.st.com 20 Absolute maximum ratings and operating conditions TS912, TS912A, TS912B 1 Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol VCC Vid Parameter Supply voltage (1) Differential input voltage (2) (3) Value Unit 18 V 18 V -0.3 to 18 V Vi Input voltage Iin Current on inputs 50 mA Io Current on outputs 130 mA -65 to +150 C Maximum junction temperature 150 C Rthja Thermal resistance junction to ambient (4) DIP8 SO-8 85 125 C/W Rthjc Thermal resistance junction to case (4) DIP8 SO-8 41 40 C/W HBM: human body model(5) 3 kV 200 V 1500 V Tstg Tj ESD Storage temperature MM: machine model(6) CDM: charged device model(7) 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of input and output voltages must never exceed VCC+ +0.3 V. 4. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. These values are typical. 5. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 k resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. 6. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 ). This is done for all couples of connected pin combinations while the other pins are floating. 7. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins. Table 2. Operating conditions Symbol 2/20 Parameter VCC Supply voltage Vicm Common mode input voltage range Toper Operating free air temperature range Doc ID 2325 Rev 6 Value Unit 2.7 to 16 V VCC--0.2 to VCC++0.2 V -40 to + 125 C TS912, TS912A, TS912B Schematic diagram 2 Schematic diagram Figure 1. Schematic diagram (1/2 TS912) VCC Non-inverting Input Internal Vref Inverting Input Output VCC Doc ID 2325 Rev 6 3/20 Electrical characteristics TS912, TS912A, TS912B 3 Electrical characteristics Table 3. VCC+ = 3 V, VCC- = 0 V, RL, CL connected to VCC/2, Tamb = 25C (unless otherwise specified) Symbol Vio Vio Parameter ICC Supply current (per amplifier, AVCL = 1, no load) Tmin Tamb Tmax CMR Common mode rejection ratio Vic = 0 to 3 V, Vo = 1.5 V SVR Supply voltage rejection ratio (VCC+ = 2.7 to 3.3 V, Vo = VCC/2) Avd Large signal voltage gain (RL = 10 k, Vo = 1.2 V to 1.8 V) Tmin Tamb Tmax VOH High level output voltage (Vid = 1 V) RL = 100 k RL = 10 k RL = 600 RL = 100 Tmin Tamb Tmax RL = 10 k RL = 600 4/20 mV V/C 5 Input bias current (1) Tmin Tamb Tmax Unit 12 7 3 (1) Iib GBP Max. 10 5 2 Input offset voltage drift Input offset current Tmin Tamb Tmax Io Typ. Input offset voltage (Vic = Vo = VCC/2) TS912 TS912A TS912B Tmin Tamb Tmax TS912 TS912A TS912B Iio VOL Min. 1 100 200 pA 1 150 300 pA 200 300 400 A 70 dB 50 80 dB 3 2 10 2.95 2.9 2.3 V/mV 2.96 2.6 2 V 2.8 2.1 Low level output voltage (Vid = -1 V) RL = 100 k RL = 10 k RL = 600 RL = 100 Tmin Tamb Tmax RL = 10 k RL = 600 30 300 900 50 70 400 mV 100 600 Output short-circuit current (Vid = 1 V) Source (Vo = VCC-) Sink (Vo = VCC+) Gain bandwidth product (AVCL = 100, RL = 10 k, CL = 100 pF, f = 100 kHz) Doc ID 2325 Rev 6 20 20 40 40 mA 0.8 MHz TS912, TS912A, TS912B Table 3. Electrical characteristics VCC+ = 3 V, VCC- = 0 V, RL, CL connected to VCC/2, Tamb = 25C (unless otherwise specified) (continued) Symbol Parameter SR+ Min. Typ. Max. Unit Slew rate (AVCL = 1, RL = 10 k, CL = 100 pF, Vi = 1.3 V to 1.7 V) 0.4 V/s SR- Slew rate (AVCL = 1, RL = 10 k, CL = 100 pF, Vi = 1.3 V to 1.7 V) 0.3 V/s m Phase margin 30 Degrees en Equivalent input noise voltage (Rs = 100 , f = 1 kHz) 30 nV/Hz 1. Maximum values include unavoidable inaccuracies of the industrial tests. Doc ID 2325 Rev 6 5/20 Electrical characteristics Table 4. TS912, TS912A, TS912B VCC+ = 5 V, VCC- = 0 V, RL, CL connected to VCC/2, Tamb = 25C (unless otherwise specified) Symbol Vio Vio Parameter Min. Typ. Input offset voltage (Vic = Vo = VCC/2) TS912 TS912A TS912B Tmin Tamb Tmax TS912 TS912A TS912B Max. 10 5 2 V/C 5 (1) Input offset current Tmin Tamb Tmax Iib Input bias current (1) Tmin Tamb Tmax ICC Supply current (per amplifier, AVCL = 1, no load) Tmin Tamb Tmax mV 12 7 3 Input offset voltage drift Iio Unit 1 100 200 pA 1 150 300 pA 230 350 450 A CMR Common mode rejection ratio Vic = 1.5 to 3.5 V, Vo = 2.5 V 60 85 dB SVR Supply voltage rejection ratio (VCC+ = 3 to 5 V, Vo = VCC/2) 55 80 dB Avd Large signal voltage gain (RL = 10 k, Vo = 1.5 V to 3.5 V) Tmin Tamb Tmax 10 7 40 VOH High level output voltage (Vid = 1V) RL = 100 k RL = 10 k RL = 600 RL = 100 Tmin Tamb Tmax RL = 10 k RL = 600 VOL 4.95 4.9 4.25 4.95 4.55 3.7 V 4.8 4.1 Low level output voltage (Vid = -1 V) RL = 100 k RL = 10 k RL = 600 RL = 100 Tmin Tamb Tmax RL = 10 k RL = 600 Output short-circuit current (Vid = 1 V) Source (Vo = VCC-) Sink (Vo = VCC+) Io V/mV 40 350 1400 50 100 500 mV 150 750 45 45 65 65 mA 1 MHz GBP Gain bandwidth product (AVCL = 100, RL = 10 k, CL = 100 pF, f = 100 kHz) SR+ Slew rate (AVCL = 1, RL = 10 k, CL = 100 pF, Vi = 1 V to 4 V) 0.8 V/s - Slew rate (AVCL = 1, RL = 10 k, CL = 100 pF, Vi = 1 V to 4 V) 0.6 V/s SR 6/20 Doc ID 2325 Rev 6 TS912, TS912A, TS912B Table 4. VCC+ = 5 V, VCC- = 0 V, RL, CL connected to VCC/2, Tamb = 25C (unless otherwise specified) (continued) Symbol en VO1/VO2 m Electrical characteristics Parameter Min. Typ. Max. Unit Equivalent input noise voltage (Rs = 100 , f = 1 kHz) 30 nV/Hz Channel separation (f = 1 kHz) 120 dB Phase margin 30 Degrees 1. Maximum values include unavoidable inaccuracies of the industrial tests. Doc ID 2325 Rev 6 7/20 Electrical characteristics Table 5. TS912, TS912A, TS912B VCC+ = 10 V, VCC- = 0 V, RL, CL connected to VCC/2, Tamb = 25C (unless otherwise specified) Symbol Vio Vio Parameter Min. Typ. Input offset voltage (Vic = Vo = VCC/2) TS912 TS912A TS912B Tmin Tamb Tmax TS912 TS912A TS912B Max. 10 5 2 V/C 5 (1) Input offset current Tmin Tamb Tmax Iib Input bias current (1) Tmin Tamb Tmax ICC Supply current (per amplifier, AVCL = 1, no load) Tmin Tamb Tmax mV 12 7 3 Input offset voltage drift Iio Unit 1 100 200 pA 1 150 300 pA 400 600 700 A CMR Common mode rejection ratio Vic = 3 to 7 V, Vo = 5 V Vic = 0 to 10 V, Vo = 5 V 60 50 90 75 dB SVR Supply voltage rejection ratio (VCC+ = 5 to 10 V, Vo = VCC/2) 60 90 dB Avd Large signal voltage gain (RL = 10 k, Vo = 2.5 V to 7.5 V) Tmin Tamb Tmax 15 10 50 VOH High level output voltage (Vid = 1V) RL = 100 k RL = 10 k RL = 600 RL = 100 Tmin Tamb Tmax RL = 10 k RL = 600 VOL Io GBP 8/20 9.95 9.85 9 V/mV 9.95 9.35 7.8 V 9.8 8.8 Low level output voltage (Vid = -1 V) RL = 100 k RL = 10 k RL = 600 RL = 100 Tmin Tamb Tmax RL = 10 k RL = 600 50 650 2300 50 150 800 mV 150 900 Output short circuit current (Vid = 1 V) Source (Vo = VCC-) Sink (Vo = VCC+) Gain bandwidth product (AVCL = 100, RL = 10 k, CL = 100 pF, f = 100 kHz) Doc ID 2325 Rev 6 45 50 65 75 mA 1.4 MHz TS912, TS912A, TS912B Table 5. Electrical characteristics VCC+ = 10 V, VCC- = 0 V, RL, CL connected to VCC/2, Tamb = 25C (unless otherwise specified) (continued) Symbol Parameter Min. Typ. Max. Unit SR+ Slew rate (AVCL = 1, RL = 10 k, CL = 100 pF, Vi = 2.5 V to 7.5 V) 1.3 V/s SR- Slew rate (AVCL = 1, RL = 10 k, CL = 100 pF, Vi = 2.5 V to 7.5 V) 0.8 V/s m Phase margin 40 Degrees en Equivalent input noise voltage (Rs = 100 , f = 1 kHz) 30 nV/Hz Total harmonic distortion (AVCL = 1, RL = 10 k, CL = 100 pF, Vo = 4.75 V to 5.25 V, f = 1 kHz) 0.02 % Input capacitance 1.5 pF THD Cin 1. Maximum values include unavoidable inaccuracies of the industrial tests. Doc ID 2325 Rev 6 9/20 Electrical characteristics Figure 2. TS912, TS912A, TS912B Supply current (each amplifier) vs. supply voltage Figure 3. 5 Tamb = 25C A VCL = 1 V O = VCC / 2 500 OUTPUT VOLTAGE, VOH (V) SUPPLY CURRENT, I CC ( m A) 600 400 300 200 100 0 High level output voltage vs. high level output current 4 8 12 2 VCC = +3V 1 -70 SUPPLY VOLTAGE, V CC (V) Figure 4. Low level output voltage vs. low level output current Figure 5. T amb = 25 C V id = -100mV VCC = +3V 2 VCC = +5V 1 0 -14 0 14 28 42 56 70 V CC = 10V V i = 5V No load 10 1 25 50 75 100 125 TEMPERATURE, T amb ( C) High level output voltage vs. high level output current Figure 7. Low level output voltage vs. low level output current T amb = 25 C Vid = 100mV 16 OUTPUT VOLTAGE, VOL (V) 10 20 OUTPUT VOLTAGE, VOH (V) -28 Input bias current vs. temperature OUTPUT CURRENT, I OL (mA) Figure 6. -42 100 INPUT BIAS CURRENT, I ib (pA) OUTPUT VOLTAGE, V OL (V) 3 -56 OUTPUT CURRENT, I OH (mA) 5 4 VCC = +5V 3 0 16 T amb = 25 C V id = 100mV 4 VCC = +16V 12 VCC = +10V 8 4 8 T amb = 25 C V id = -100mV 6 V CC = 16V 4 V CC = 10V 2 0 -70 -56 -42 -28 -14 0 14 28 42 56 70 OUTPUT CURRENT, I OL (mA) OUTPUT CURRENT, IOH (mA) 10/20 0 Doc ID 2325 Rev 6 TS912, TS912A, TS912B GAIN GAIN (dB) 40 30 PHASE 20 Phase Margin Tamb = 25C VCC = 10V R L = 10k W C L = 100pF A VCL = 100 10 0 0 45 90 135 Gain Bandwidth Product 180 -10 10 2 10 3 4 5 6 10 10 10 FREQUENCY, f (Hz) 10 7 1000 600 200 0 4 8 40 30 12 30 16 16 10 10 Phase Margin Tamb = 25C V CC = 10V R L = 600W C L = 100pF A VCL = 100 20 2 SUPPLY VOLTAGE, VCC (V) 10 3 0 45 PHASE 0 10 20 8 12 GAIN 40 GAIN (dB) PHASE MARGIN, f m (Degrees) 1400 50 Tamb = 25C R L = 10kW C L = 100pF 4 Tamb = 25C R L = 10kW C L = 100pF Figure 11. Gain and phase vs. frequency 60 0 1800 SUPPLY VOLTAGE, VCC (V) Figure 10. Phase margin vs. supply voltage 50 Gain bandwidth product vs. supply voltage 135 Gain Bandwidth Product 4 5 10 10 10 FREQUENCY, f (Hz) 90 180 6 10 PHASE (Degrees) 50 Figure 9. GAIN BANDW. PROD., GBP (kHz) Gain and phase vs. frequency PHASE (Degrees) Figure 8. Electrical characteristics 7 1800 PHASE MARGIN, fm (Degrees) GAIN BANDW. PROD., GBP (kHz) Figure 12. Gain bandwidth product vs. supply Figure 13. Phase margin vs. supply voltage voltage Tamb = 25C R L = 600W C L = 100pF 1400 1000 600 200 0 4 8 12 60 Tamb = 25C R L = 600W C L = 100pF 50 40 30 20 16 SUPPLY VOLTAGE, VCC (V) 0 4 8 12 16 SUPPLY VOLTAGE, VCC (V) Doc ID 2325 Rev 6 11/20 Macromodel TS912, TS912A, TS912B EQUIVALENT INPUT VOLTAGE NOISE (nV/VHz) Figure 14. Input voltage noise vs. frequency 150 VCC = 10V Tamb = 25C RS = 100W 100 50 0 10 100 1000 10000 FREQUENCY (Hz) 4 Macromodel 4.1 Important note concerning this macromodel All models are a trade-off between accuracy and complexity (i.e. simulation time). Macromodels are not a substitute to breadboarding; rather, they confirm the validity of a design approach and help to select surrounding component values. A macromodel emulates the nominal performance of a typical device within specified operating conditions (temperature, supply voltage, for example). Thus the macromodel is often not as exhaustive as the datasheet, its purpose is to illustrate the main parameters of the product. Data derived from macromodels used outside of the specified conditions (VCC, temperature, for example) or even worse, outside of the device operating conditions (VCC, Vicm, for example), is not reliable in any way. 12/20 Doc ID 2325 Rev 6 TS912, TS912A, TS912B 4.2 Macromodel Macromodel code ** Standard Linear Ics Macromodels, 1993. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TS912 1 2 3 4 5 ********************************************************** .MODEL MDTH D IS=1E-8 KF=6.563355E-14 CJO=10F * INPUT STAGE CIP 2 5 1.500000E-12 CIN 1 5 1.500000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 6.500000E+00 RIN 15 16 6.500000E+00 RIS 11 15 7.655100E+00 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0.000000E+00 VOFN 13 14 DC 0 IPOL 13 5 4.000000E-05 CPS 11 15 3.82E-08 DINN 17 13 MDTH 400E-12 VIN 17 5 -0.5000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 -0.5000000E+00 FCP 4 5 VOFP 7.750000E+00 FCN 5 4 VOFN 7.750000E+00 * AMPLIFYING STAGE FIP 5 19 VOFP 5.500000E+02 FIN 5 19 VOFN 5.500000E+02 RG1 19 5 5.087344E+05 RG2 19 4 5.087344E+05 CC 19 29 2.200000E-08 HZTP 30 29 VOFP 12.33E+02 HZTN 5 30 VOFN 12.33E+02 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 3135 VIPM 28 4 150 HONM 21 27 VOUT 3135 VINM 5 27 150 EOUT 26 23 19 5 1 VOUT 23 5 0 ROUT 26 3 65 COUT 3 5 1.000000E-12 DOP 19 68 MDTH 400E-12 VOP 4 25 1.924 Doc ID 2325 Rev 6 13/20 Macromodel TS912, TS912A, TS912B HSCP 68 25 VSCP1 1E8 DON 69 19 MDTH 400E-12 VON 24 5 2.4419107 HSCN 24 69 VSCN1 1.5E8 VSCTHP 60 61 0.1375 DSCP1 61 63 MDTH 400E-12 VSCP1 63 64 0 ISCP 64 0 1.000000E-8 DSCP2 0 64 MDTH 400E-12 DSCN2 0 74 MDTH 400E-12 ISCN 74 0 1.000000E-8 VSCN1 73 74 0 DSCN1 71 73 MDTH 400E-12 VSCTHN 71 70 -0.75 ESCP 60 0 2 1 500 ESCN 70 0 2 1 -2000 .ENDS 14/20 Doc ID 2325 Rev 6 TS912, TS912A, TS912B 5 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Doc ID 2325 Rev 6 15/20 Package information 5.1 TS912, TS912A, TS912B DIP8 package information Figure 15. DIP8 package mechanical drawing Table 6. DIP8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 5.33 Max. 0.210 A1 0.38 0.015 A2 2.92 3.30 4.95 0.115 0.130 0.195 b 0.36 0.46 0.56 0.014 0.018 0.022 b2 1.14 1.52 1.78 0.045 0.060 0.070 c 0.20 0.25 0.36 0.008 0.010 0.014 D 9.02 9.27 10.16 0.355 0.365 0.400 E 7.62 7.87 8.26 0.300 0.310 0.325 E1 6.10 6.35 7.11 0.240 0.250 0.280 e 2.54 0.100 eA 7.62 0.300 eB L 16/20 Inches 10.92 2.92 3.30 3.81 Doc ID 2325 Rev 6 0.430 0.115 0.130 0.150 TS912, TS912A, TS912B 5.2 Package information SO-8 package information Figure 16. SO-8 package mechanical drawing Table 7. SO-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.75 0.069 A1 0.10 A2 1.25 b 0.28 0.48 0.011 0.019 c 0.17 0.23 0.007 0.010 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 0.25 Max. 0.004 0.010 0.049 1.27 0.050 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 L1 k ccc 1.04 0 0.040 8 0.10 Doc ID 2325 Rev 6 1 8 0.004 17/20 Ordering information 6 TS912, TS912A, TS912B Ordering information Table 8. Order codes Part number Temperature range Package Packing DIP8 Tube Marking TS912IN TS912IN TS912AIN TS912AIN TS912ID TS912IDT 912I TS912AID TS912AIDT TS912BID TS912BIDT SO-8 -40C, +125C 912BI Tube or Tape & reel TS912IYD TS912IYDT(1) TS912AIYD TS912AIYDT(1) 912AI 912IY SO-8 (Automotive grade level) TS912BIYD TS912BIYDT(1) 912BY 1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent. 18/20 912AIY Doc ID 2325 Rev 6 TS912, TS912A, TS912B 7 Revision history Revision history Table 9. Document revision history Date Revision Changes 04-Dec-2001 1 First release. 31-Jul-2005 2 PPAP references inserted in the datasheet, see order codes table. ESD protection inserted in AMR table. 03-Oct-2005 3 Some errors in the Order Codes table were corrected. Reorganization of Section 4: Macromodel. 13-Feb- 2006 4 Parameters added in AMR table (Tj, ESD, Rthja, Rthjc). 16-Oct-2007 5 Corrected units and ESD footnotes in Table 1: Absolute maximum ratings. Corrected misalignments in electrical characteristics table. Updated Section 4: Macromodel. Added missing automotive grade order codes and footnote in Table 8: Order codes. Format update. 01-Feb-2010 6 Added TS912A and TS912B part numbers on cover page. Doc ID 2325 Rev 6 19/20 TS912, TS912A, TS912B Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20 Doc ID 2325 Rev 6