LMC6484 LMC6484 CMOS Quad Rail-to-Rail Input and Output Operational Amplifier Literature Number: SNOS675B LMC6484 CMOS Quad Rail-to-Rail Input and Output Operational Amplifier General Description Features The LMC6484 provides a common-mode range that extends to both supply rails. This rail-to-rail performance combined with excellent accuracy, due to a high CMRR, makes it unique among rail-to-rail input amplifiers. It is ideal for systems, such as data acquisition, that require a large input signal range. The LMC6484 is also an excellent upgrade for circuits using limited common-mode range amplifiers such as the TLC274 and TLC279. Maximum dynamic signal range is assured in low voltage and single supply systems by the LMC6484's rail-to-rail output swing. The LMC6484's rail-to-rail output swing is guaranteed for loads down to 600. Guaranteed low voltage characteristics and low power dissipation make the LMC6484 especially well-suited for battery-operated systems. See the LMC6482 data sheet for a Dual CMOS operational amplifier with these same features. (Typical unless otherwise noted) n Rail-to-Rail Input Common-Mode Voltage Range (Guaranteed Over Temperature) n Rail-to-Rail Output Swing (within 20 mV of supply rail, 100 k load) n Guaranteed 3V, 5V and 15V Performance n Excellent CMRR and PSRR: 82 dB n Ultra Low Input Current: 20 fA n High Voltage Gain (RL = 500 k): 130 dB n Specified for 2 k and 600 loads Applications Data Acquisition Systems Transducer Amplifiers Hand-held Analytic Instruments Medical Instrumentation Active Filter, Peak Detector, Sample and Hold, pH Meter, Current Source n Improved Replacement for TLC274, TLC279 n n n n n 3V Single Supply Buffer Circuit Rail-to-Rail Input Rail-to-Rail Output DS011714-2 DS011714-3 DS011714-1 (c) 2001 National Semiconductor Corporation DS011714 www.national.com LMC6484 CMOS Quad Rail-to-Rail Input and Output Operational Amplifier August 2000 LMC6484 Absolute Maximum Ratings (Note 1) Storage Temperature Range Junction Temperature (Note 4) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Differential Input Voltage Voltage at Input/Output Pin Supply Voltage (V+ - V-) Current at Input Pin (Note 12) Current at Output Pin (Notes 3, 8) Current at Power Supply Pin Lead Temp. (Soldering, 10 sec.) -65C to +150C 150C Operating Ratings 2.0 kV (Note 1) Supply Voltage Junction Temperature Range LMC6484AM LMC6484AI, LMC6484I Thermal Resistance (JA) N Package, 14-Pin Molded DIP M Package, 14-Pin Surface Mount Supply Voltage (V+) + 0.3V, (V-) - 0.3V 16V 5 mA 30 mA 40 mA 260C 3.0V V+ 15.5V -55C TJ +125C -40C TJ +85C 70C/W 110C/W DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2 and RL > 1M. Boldface limits apply at the temperature extremes. Typ Symbol Parameter Conditions (Note 5) LMC6484AI LMC6484I Limit Limit Limit (Note 6) (Note 6) (Note 6) VOS TCVOS Input Offset Voltage 0.110 Input Offset Voltage LMC6484M Units 0.750 3.0 3.0 mV 1.35 3.7 3.8 max 1.0 V/C Average Drift IB Input Current (Note 13) 0.02 4.0 4.0 100 pA max IOS Input Offset Current (Note 13) 0.01 2.0 2.0 50 pA max CIN Common-Mode 3 pF Input Capacitance RIN Input Resistance CMRR Common Mode Rejection Ratio 82 70 65 65 67 62 60 70 65 65 67 62 60 82 70 65 65 dB 67 62 60 min 82 70 65 65 dB 67 62 60 min -0.25 -0.25 -0.25 V 0 0 0 max V+ + 0.25 V+ + 0.25 V+ + 0.25 V + V = 15V 0V VCM 5.0V 82 V+ = 5V +PSRR Positive Power Supply Rejection Ratio -PSRR Negative Power Supply VCM Tera > 10 0V VCM 15.0V, 5V V+ 15V, - V = 0V, VO = 2.5V -5V V- -15V, Rejection Ratio V+ = 0V, VO = -2.5V Input Common-Mode V+ = 5V and 15V Voltage Range For CMRR 50 dB V- - 0.3 V+ + 0.3 + AV Large Signal RL = 2k Voltage Gain (Notes 7, 13) RL = 600 + V V V min Sourcing 666 140 120 120 V/mV 84 72 60 min Sinking 75 35 35 35 V/mV 20 20 18 min Sourcing 300 80 50 50 V/mV 48 30 25 min 20 15 15 V/mV 13 10 8 min (Notes 7, 13) Sinking www.national.com + dB min 35 2 (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2 and RL > 1M. Boldface limits apply at the temperature extremes. Typ Symbol Parameter Conditions (Note 5) LMC6484AI Limit Output Swing V+ = 5V Limit Limit (Note 6) 4.8 4.8 4.8 V 4.7 4.7 4.7 min 0.18 0.18 0.18 V 0.24 0.24 0.24 max 4.5 4.5 4.5 V 4.24 4.24 4.24 min 0.5 0.5 0.5 V 0.65 0.65 0.65 max 14.7 14.4 14.4 14.4 V 14.2 14.2 14.2 min 0.16 0.32 0.32 0.32 V 0.45 0.45 0.45 max 13.4 13.4 13.4 V 13.0 13.0 13.0 min 1.0 1.0 1.0 V 1.3 1.3 1.3 max 16 16 16 mA 12 12 10 min 11 11 11 mA 9.5 9.5 8.0 min 28 28 28 mA 22 22 20 min 30 30 30 mA 24 24 22 min 2.8 2.8 2.8 mA 3.6 3.6 3.8 max 4.9 RL = 2 k to V+/2 0.1 V+ = 5V 4.7 + RL = 600 to V /2 0.3 V+ = 15V + RL = 2 k to V /2 V+ = 15V 14.1 RL = 600 to V+/2 0.5 ISC Output Short Circuit Sourcing, VO = 0V 20 Current ISC V+ = 5V Sinking, VO = 5V 15 Output Short Circuit Sourcing, VO = 0V 30 Current V+ = 15V Sinking, VO = 12V 30 (Note 8) IS Supply Current All Four Amplifiers 2.0 V+ = +5V, VO = V+/2 All Four Amplifiers LMC6484M (Note 6) (Note 6) VO LMC6484I 2.6 V+ = +15V, VO = V+/2 Units 3.0 3.0 3.0 mA 3.8 3.8 4.0 max AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2 and RL > 1M. Boldface limits apply at the temperature extremes. Symbol SR Parameter Slew Rate GBW Gain-Bandwidth Product m Gm in (Note 9) Typ LMC6484A LMC6484I LMC6484M (Note 5) Limit Limit Limit (Note 6) (Note 6) (Note 6) 1.0 0.9 0.9 0.7 0.63 0.54 1.3 V+ = 15V Units V/s min 1.5 MHz Phase Margin 50 Deg Gain Margin 15 dB (Note 10) 150 dB Input-Referred f = 1 kHz 37 Voltage Noise VCM = 1V Input-Referred f = 1 kHz Amp-to-Amp Isolation en Conditions 0.03 Current Noise 3 www.national.com LMC6484 DC Electrical Characteristics LMC6484 AC Electrical Characteristics (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2 and RL > 1M. Boldface limits apply at the temperature extremes. Typ Symbol T.H.D. Parameter Conditions Total Harmonic Distortion LMC6484A (Note 5) f = 1 kHz, AV = -2 LMC6484I LMC6484M Limit Limit Limit (Note 6) (Note 6) (Note 6) Units 0.01 % 0.01 % RL = 10 k, VO = 4.1 VPP f = 10 kHz, AV = -2 RL = 10 k, VO = 8.5 VPP V+ = 10V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 3V, V- = 0V, VCM = VO = V+/2 and RL > 1M Symbol VOS TCVOS Parameter Conditions Typ LMC6484AI LMC6484I (Note 5) Limit Limit Limit (Note 6) (Note 6) (Note 6) Input Offset Voltage 0.9 Input Offset Voltage LMC6484M Units 2.0 3.0 3.0 mV 2.7 3.7 3.8 max 2.0 V/C pA Average Drift IB Input Bias Current 0.02 IOS Input Offset Current 0.01 CMRR Common Mode pA 0V VCM 3V 74 64 60 60 3V V+ 15V, V- = 0V 80 68 60 60 Rejection Ratio PSRR Power Supply min Rejection Ratio VCM Input Common-Mode dB dB min For CMRR 50 dB V- - 0.25 0 0 0 Voltage Range V max V+ + 0.25 V+ V+ V+ V min VO Output Swing RL = 2 k to V+/2 2.8 V 0.2 RL = 600 to V+/2 V 2.7 2.5 2.5 2.5 0.37 0.6 0.6 0.6 V min V max IS Supply Current All Four Amplifiers 1.65 2.5 2.5 2.5 mA 3.0 3.0 3.2 max AC Electrical Characteristics Unless otherwise specified, V+ = 3V, V- = 0V, VCM = VO = V+/2 and RL > 1M Typ Symbol Parameter SR Slew Rate GBW Gain-Bandwidth Product T.H.D. Total Harmonic Distortion Conditions (Note 5) (Note 11) f = 10 kHz, AV = -2 LMC6484AI LMC6484I LMC6484M Limit Limit Limit (Note 6) (Note 6) (Note 6) Units 0.9 V/s 1.0 MHz 0.01 % RL = 10 k, VO = 2 VPP Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. www.national.com 4 (Continued) Note 2: Human body model, 1.5 k in series with 100 pF. All pins rated per method 3015.6 of MIL-STD-883. This is a class 2 device rating. Note 3: Applies to both single supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Output currents in excess of 30 mA over long term may adversely affect reliability. Note 4: The maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max) - TA)/JA. All numbers apply for packages soldered directly into a PC board. Note 5: Typical Values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V VO 11.5V. For Sinking tests, 3.5V VO 7.5V. Note 8: Do not short circuit output to V+, when V+ is greater than 13V or reliability will be adversely affected. Note 9: V+ = 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of either the positive or negative slew rates. Note 10: Input referred, V+ = 15V and RL = 100 k connected to 7.5V. Each amp excited in turn with 1 kHz to produce VO = 12 VPP. Note 11: Connected as Voltage Follower with 2V step input. Number specified is the slower of either the positive or negative slew rates. Note 12: Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings. Note 13: Guaranteed limits are dictated by tester limitations and not device performance. Actual performance is reflected in the typical value. Note 14: For guaranteed Military Temperature Range parameters see RETSMC6484X. Typical Performance Characteristics VS = +15V, Single Supply, TA = 25C unless otherwise specified Supply Current vs Supply Voltage Input Current vs Temperature Sourcing Current vs Output Voltage DS011714-39 Sourcing Current vs Output Voltage DS011714-40 Sourcing Current vs Output Voltage DS011714-42 Sinking Current vs Output Voltage DS011714-43 5 DS011714-41 DS011714-44 www.national.com LMC6484 AC Electrical Characteristics LMC6484 Typical Performance Characteristics VS = +15V, Single Supply, TA = 25C unless otherwise specified (Continued) Sinking Current vs Output Voltage Sinking Current vs Output Voltage DS011714-45 Output Voltage Swing vs Supply Voltage DS011714-46 Input Voltage Noise vs Frequency Input Voltage Noise vs Input Voltage DS011714-48 Input Voltage Noise vs Input Voltage DS011714-49 Input Voltage Noise vs Input Voltage DS011714-50 www.national.com DS011714-47 Crosstalk Rejection vs Frequency DS011714-51 6 DS011714-52 VS = +15V, Single Supply, TA = 25C unless otherwise specified (Continued) Crosstalk Rejection vs Frequency Positive PSRR vs Frequency Negative PSRR vs Frequency DS011714-53 CMRR vs Frequency DS011714-54 CMRR vs Input Voltage CMRR vs Input Voltage DS011714-57 DS011714-56 VOS vs CMR CMRR vs Input Voltage DS011714-55 DS011714-58 VOS vs CMR DS011714-59 DS011714-60 7 DS011714-61 www.national.com LMC6484 Typical Performance Characteristics LMC6484 Typical Performance Characteristics VS = +15V, Single Supply, TA = 25C unless otherwise specified (Continued) Input Voltage vs Output Voltage Input Voltage vs Output Voltage DS011714-62 Open Loop Frequency Response DS011714-63 Open Loop Frequency Response vs Temperature DS011714-65 Gain and Phase vs Capacitive Load DS011714-64 Maximum Output Swing vs Frequency DS011714-67 DS011714-66 Gain and Phase vs Capacitive Load DS011714-68 www.national.com Open Loop Frequency Response Open Loop Output Impedance vs Frequency DS011714-69 8 DS011714-70 VS = +15V, Single Supply, TA = 25C unless otherwise specified (Continued) Open Loop Output Impedance vs Frequency Slew Rate vs Supply Voltage Non-Inverting Large Signal Pulse Response Non-Inverting Large Signal Pulse Response Non-Inverting Large Signal Pulse Response DS011714-74 Non-Inverting Small Signal Pulse Response DS011714-73 DS011714-72 DS011714-71 Non-Inverting Small Signal Pulse Response DS011714-75 Non-Inverting Small Signal Pulse Response DS011714-77 DS011714-78 9 DS011714-76 Inverting Large Signal Pulse Response DS011714-79 www.national.com LMC6484 Typical Performance Characteristics LMC6484 Typical Performance Characteristics VS = +15V, Single Supply, TA = 25C unless otherwise specified (Continued) Inverting Large Signal Pulse Response Inverting Large Signal Pulse Response DS011714-80 Inverting Small Signal Pulse Response Inverting Small Signal Pulse Response DS011714-81 Inverting Small Signal Pulse Response DS011714-83 DS011714-82 Stability vs Capacitive Load DS011714-84 DS011714-85 Stability vs Capacitive Load Stability vs Capacitive Load Stability vs Capacitive Load DS011714-86 www.national.com DS011714-87 10 DS011714-88 VS = +15V, Single Supply, TA = 25C unless otherwise specified (Continued) Stability vs Capacitive Load Stability vs Capacitive Load DS011714-89 DS011714-90 ceeding this absolute maximum rating, as in Figure 2, can cause excessive current to flow in or out of the input pins possibly affecting reliability. Application Information 1.0 Amplifier Topology The LMC6484 incorporates specially designed wide-compliance range current mirrors and the body effect to extend input common mode range to each supply rail. Complementary paralleled differential input stages, like the type used in other CMOS and bipolar rail-to-rail input amplifiers, were not used because of their inherent accuracy problems due to CMRR, cross-over distortion, and open-loop gain variation. The LMC6484's input stage design is complemented by an output stage capable of rail-to-rail output swing even when driving a large load. Rail-to-rail output swing is obtained by taking the output directly from the internal integrator instead of an output buffer stage. DS011714-12 2.0 Input Common-Mode Voltage Range Unlike Bi-FET amplifier designs, the LMC6484 does not exhibit phase inversion when an input voltage exceeds the negative supply voltage. Figure 1 shows an input voltage exceeding both supplies with no resulting phase inversion on the output. FIGURE 2. A 7.5V Input Signal Greatly Exceeds the 3V Supply in Figure 3 Causing No Phase Inversion Due to RI Applications that exceed this rating must externally limit the maximum input current to 5 mA with an input resistor as shown in Figure 3. DS011714-11 FIGURE 3. RI Input Current Protection for Voltages Exceeding the Supply Voltage 3.0 Rail-To-Rail Output The approximated output resistance of the LMC6484 is 180 sourcing and 130 sinking at VS = 3V and 110 sourcing and 83 sinking at VS = 5V. Using the calculated output resistance, maximum output voltage swing can be estimated as a function of load. DS011714-10 FIGURE 1. An Input Voltage Signal Exceeds the LMC6484 Power Supply Voltages with No Output Phase Inversion The absolute maximum input voltage is 300 mV beyond either supply rail at room temperature. Voltages greatly ex- 4.0 Capacitive Load Tolerance The LMC6484 can typically directly drive a 100 pF load with VS = 15V at unity gain without oscillating. The unity gain follower is the most sensitive configuration. Direct capacitive 11 www.national.com LMC6484 Typical Performance Characteristics LMC6484 Application Information (Continued) loading reduces the phase margin of op-amps. The combination of the op-amp's output impedance and the capacitive load induces phase lag. This results in either an underdamped pulse response or oscillation. Capacitive load compensation can be accomplished using resistive isolation as shown in Figure 4. This simple technique is useful for isolating the capacitive input of multiplexers and A/D converters. DS011714-17 DS011714-16 FIGURE 4. Resistive Isolation of a 330 pF Capacitive Load FIGURE 7. Pulse Response of LMC6484 Circuit in Figure 6 5.0 Compensating for Input Capacitance It is quite common to use large values of feedback resistance with amplifiers that have ultra-low input current, like the LMC6484. Large feedback resistors can react with small values of input capacitance due to transducers, photodiodes, and circuit board parasitics to reduce phase margins. DS011714-18 FIGURE 5. Pulse Response of the LMC6484 Circuit in Figure 4 DS011714-19 FIGURE 8. Canceling the Effect of Input Capacitance Improved frequency response is achieved by indirectly driving capacitive loads as shown in Figure 6. The effect of input capacitance can be compensated for by adding a feedback capacitor. The feedback capacitor (as in Figure 8 ), Cf, is first estimated by: or R1 CIN R2 Cf which typically provides significant overcompensation. Printed circuit board stray capacitance may be larger or smaller than that of a breadboard, so the actual optimum value for Cf may be different. The values of Cf should be checked on the actual circuit. (Refer to the LMC660 quad CMOS amplifier data sheet for a more detailed discussion.) DS011714-15 FIGURE 6. LMC6484 Non-Inverting Amplifier, Compensated to Handle a 330 pF Capacitive Load R1 and C1 serve to counteract the loss of phase margin by feeding forward the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. The values of R1 and C1 are experimentally determined for the desired pulse response. The resulting pulse response can be seen in Figure 7. www.national.com 6.0 Printed-Circuit-Board Layout for High-Impedance Work It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires special layout of the PC board. when one wishes to take advantage 12 LMC6484 Application Information (Continued) of the ultra-low input current of the LMC6484, typically less than 20 fA, it is essential to have an excellent layout. Fortunately, the techniques of obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC6484's inputs and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc. connected to the op-amp's inputs, as in Figure 9. To have a significant effect, guard rings should be placed in both the top and bottom of the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012, which is normally considered a very large resistance, could leak 5 pA if the trace were a 5V bus adjacent to the pad of the input. This would cause a 250 times degradation from the LMC6484's actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a resistance of 1011 would cause only 0.05 pA of leakage current. See Figure 10 for typical connections of guard rings for standard op-amp configurations. DS011714-21 Inverting Amplifier DS011714-22 Non-Inverting Amplifier DS011714-23 Follower FIGURE 10. Typical Connections of Guard Rings The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 11. DS011714-20 FIGURE 9. Example of Guard Ring in P.C. Board Layout DS011714-24 (Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board.) FIGURE 11. Air Wiring 13 www.national.com LMC6484 Application Information (Continued) 7.0 Offset Voltage Adjustment Offset voltage adjustment circuits are illustrated in Figures 13, 14. Large value resistances and potentiometers are used to reduce power consumption while providing typically 2.5 mV of adjustment range, referred to the input, for both configurations with VS = 5V. DS011714-26 FIGURE 13. Non-Inverting Configuration Offset Voltage Adjustment 8.0 Upgrading Applications The LMC6484 quads and LMC6482 duals have industry standard pin outs to retrofit existing applications. System performance can be greatly increased by the LMC6484's features. The key benefit of designing in the LMC6484 is increased linear signal range. Most op-amps have limited input common mode ranges. Signals that exceed this range generate a non-linear output response that persists long after the input signal returns to the common mode range. Linear signal range is vital in applications such as filters where signal peaking can exceed input common mode ranges resulting in output phase inversion or severe distortion. DS011714-25 FIGURE 12. Inverting Configuration Offset Voltage Adjustment 9.0 Data Acquisition Systems Low power, single supply data acquisition system solutions are provided by buffering the ADC12038 with the LMC6484 (Figure 14). Capable of using the full supply range, the LMC6484 does not require input signals to be scaled down to meet limited common mode voltage ranges. The LMC6484 CMRR of 82 dB maintains integral linearity of a 12-bit data acquisition system to 0.325 LSB. Other rail-to-rail input amplifiers with only 50 dB of CMRR will degrade the accuracy of the data acquisition system to only 8 bits. www.national.com 14 LMC6484 Application Information (Continued) DS011714-28 FIGURE 14. Operating from the same Supply Voltage, the LMC6484 buffers the ADC12038 maintaining excellent accuracy cations that benefit from these features include analytic medical instruments, magnetic field detectors, gas detectors, and silicon-based transducers. A small valued potentiometer is used in series with Rg to set the differential gain of the 3 op-amp instrumentation circuit in Figure 15. This combination is used instead of one large valued potentiometer to increase gain trim accuracy and reduce error due to vibration. 10.0 Instrumentation Circuits The LMC6484 has the high input impedance, large common-mode range and high CMRR needed for designing instrumentation circuits. Instrumentation circuits designed with the LMC6484 can reject a larger range of common-mode signals than most in-amps. This makes instrumentation circuits designed with the LMC6484 an excellent choice for noisy or industrial environments. Other appli- DS011714-29 FIGURE 15. Low Power 3 Op-Amp Instrumentation Amplifier 15 www.national.com LMC6484 Application Information Higher frequency and larger common-mode range applications are best facilitated by a three op-amp instrumentation amplifier. (Continued) A 2 op-amp instrumentation amplifier designed for a gain of 100 is shown in Figure 16. Low sensitivity trimming is made for offset voltage, CMRR and gain. Low cost and low power consumption are the main advantages of this two op-amp circuit. DS011714-30 FIGURE 16. Low-Power Two-Op-Amp Instrumentation Amplifier 11.0 Spice Macromodel A spice macromodel is available for the LMC6484. This model includes accurate simulation of: * input common-mode voltage range * frequency and transient response * GBW dependence on loading conditions * quiescent and dynamic supply current * output swing dependence on loading conditions and many more characteristics as listed on the macromodel disk. Contact your local National Semiconductor sales office to obtain an operational amplifier spice model library disk. Typical Single-Supply Applications DS011714-32 FIGURE 18. Half-Wave Rectifier Waveform The circuit in Figure 17 use a single supply to half wave rectify a sinusoid centered about ground. RI limits current into the amplifier caused by the input voltage exceeding the supply voltage. Full wave rectification is provided by the circuit in Figure 19. DS011714-31 FIGURE 17. Half-Wave Rectifier with Input Current Protection (RI) DS011714-33 FIGURE 19. Full Wave Rectifier with Input Current Protection (RI) www.national.com 16 LMC6484 Typical Single-Supply Applications (Continued) DS011714-34 FIGURE 20. Full Wave Rectifier Waveform DS011714-35 FIGURE 21. Large Compliance Range Current Source DS011714-36 FIGURE 22. Positive Supply Current Sense 17 www.national.com LMC6484 Typical Single-Supply Applications (Continued) DS011714-37 FIGURE 23. Low Voltage Peak Detector with Rail-to-Rail Peak Capture Range In Figure 23 dielectric absorption and leakage is minimized by using a polystyrene or polyethylene hold capacitor. The droop rate is primarily determined by the value of CH and diode leakage current. The ultra-low input current of the LMC6484 has a negligible effect on droop. DS011714-38 FIGURE 24. Rail-to-Rail Sample and Hold The LMC6484's high CMRR (85 dB) allows excellent accuracy throughout the circuit's rail-to-rail dynamic capture range. DS011714-27 FIGURE 25. Rail-to-Rail Single Supply Low Pass Filter The low pass filter circuit in Figure 25 can be used as an anti-aliasing filter with the same voltage supply as the A/D converter. Filter designs can also take advantage of the LMC6484 ultra-low input current. The ultra-low input current yields negligible offset error even when large value resistors are used. This in turn allows the use of smaller valued capacitors which take less board space and cost less. www.national.com 18 LMC6484 Connection Diagram DS011714-4 Ordering Information Package Temperature Range Military Industrial -55C to +125C -40C to +85C 14-pin LMC6484AIN Molded DIP Transport Media N14A Rail M14A Rail LMC6484IN 14-pin LMC6484AIM, AIMX Small Outline 14-pin Ceramic DIP NSC Drawing LMC6484IM, IMX LMC6484AMJ/883 Tape and Reel J14A 19 Rail www.national.com LMC6484 Physical Dimensions inches (millimeters) unless otherwise noted 14-Pin Ceramic Dual-In-Line Package Order Number LMC6484AMJ/883 NS Package Number J14A www.national.com 20 LMC6484 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Pin Small Outline Order Package Number LMC6484AIM, LMC6484AIMX, LMC6484IM or LMC6484IMX NS Package Number M14A 21 www.national.com LMC6484 CMOS Quad Rail-to-Rail Input and Output Operational Amplifier Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Pin Molded DIP Order Package Number LMC6484AIN, LMC6484IN or LMC6484MN NS Package Number N14A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated