871
Audio ICs
Low-current audio headphone driver
BA3575FS
The BA3575FS is a headphone driver with an AVC circuit that keeps the output below a fixed level. It features low current
consumption, and low output noise, and is ideal for use in portable digital audio equipment.
Applications
Portable CD players
Features
1) Low current consumption (when VCC = 2.4 V, the
quiescent current is 4.9mA).
2) Suitable for use in digital audio equipment (voltage
gain: GV = 11.8dB, output noise voltage: VNO =
–102dBm typ.).
3) ATT circuit (gain switch).
4) AVC (Auto Volume Control) circuit, for output limiting.
5) Internal standby switch.
6) Internal mute switch.
7) Internal ripple filter.
8) No output coupling capacitor required.
9) Internal beep circuit.
10) SSOP-A20 package.
Absolute maximum ratings (Ta = 25C)
Recommended operating conditions (Ta = 25C)
872
Audio ICs BA3575FS
Block diagram
873
Audio ICs BA3575FS
Pin descriptions
874
Audio ICs BA3575FS
875
Audio ICs BA3575FS
876
Audio ICs BA3575FS
877
Audio ICs BA3575FS
Electrical characteristics(unless otherwis noted, Ta = 25C, VCC = 2.4V, RL = 16Ω, f = 1kHz, DIN AUDIO,
PWSW = ON, MUTE = OFF, ATT = OFF, and AVC = OFF)
878
Audio ICs BA3575FS
Measurement circuit
879
Audio ICs BA3575FS
Measurement circuit switch table (Fig.1)
880
Audio ICs BA3575FS
Application example
881
Audio ICs BA3575FS
Application notes
(1) “Pop” sound
By operating the BA3575FS according to the timing chart shown in Fig.3, it is possible to suppress generation of “pop”
noise in the headphone output.
(2) Application circuits
Provided the recommended circuit constants are used,
the application circuits should function correctly . Howev-
er, we recommend that you confirm the characteristics of
the circuits in actual use. If you change the circuit
constants, check both the static and transient character-
istics of the circuit, and allow sufficient margin to accom-
modate variations between both ICs and external com-
ponents.
In particular, the capacitors connected to the OUT 1,
OUT 2, and VREF pins must have low impedance at high
frequency, and have sufficient margin in their tempera-
ture characteristics.
Also, use an electrolytic or tantalum capacitor for the ca-
pacitor connected to the BIASOUT terminal.
(3) The PCB pattern for the external components
should be designed carefully to prevent oscillation and
degradation of the circuit characteristics. Keep the wiring
tracks as short as possible, and ensure that there is no
impedance between the common connections.
The ripple filter pins (1 and 2) and the bias amplifier pins
(3 and 4) cannot be used for external power supplies or
reference voltages.
882
Audio ICs BA3575FS
(4) Recommended operating conditions
The curves in Fig.4 below show the maximum allowable
power output (PO (Max.)/ch) plotted against the supply volt-
age (VCC) for different values of ambient temperature
(Ta). When VCC 3.6 V, operate the IC in the region be-
low the dotted line, and do not exceed it.
If the maximum allowable power output for each channel
(PO (Max.)/ch) is exceeded, the internal power consump-
tion will exceed the power dissipation capacity of the
package, and destroy the IC.
Electrical characteristics curves
External dimensions (Units: mm)
883
Audio ICs BA3575FS
Appendix
Appendix1-Rev1.0
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document use silicon as a basic material.
Products listed in this document are no antiradiation design.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
