PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/ Line Drivers Features Description * PI74FCT244/541T and PI74FCT2244/2541T are pin compatible with bipolar Fast Series at a higher speed and lower power consumption * 25 series resistor on all outputs (FCT2XXX only) * TTL input and output levels * Low ground bounce outputs * Extremely low static power * Hysteresis on all inputs * Industrial operating temperature range: -40C to +85C * Packaging (Pb-free & Green available): Pericom Semiconductor's PI74FCT244T/541T and P174FCT2244/ 2541T are 8-bit wide driver circuits, designed to be used in applications requiring high-speed and high-output drive. Ideal applications would include bus drivers, memory drivers, address drivers, and system clock drivers. The PI74FCT541 and 2541T provide similar driver capabilities, but have their pins physically grouped by function. All inputs are located on one side of the package, while outputs are on the opposite side, allowing for a much simpler and denser board layout. All PI74FCT2XXX devices have a built-in 25 series resistor on all outputs to reduce noise because of reflections, thus eliminating the need for an external terminating resistor. PI74FCT244T - 20-pin 173-mil wide plastic TSSOP (L) - 20-pin 209-mil wide plastic SSOP (H) - 20-pin 150-mil wide plastic QSOP (Q) - 20-pin 300-mil wide plastic SOIC (S) PI74FCT2244T - 20-pin 173-mil wide plastic TSSOP (L) - 20-pin 150-mil wide plastic QSOP (Q) - 20-pin 300-mil wide plastic SOIC (S) PI74FCT541T (Pb-free & Green) - 20-pin 173-mil wide plastic TSSOP (L) - 20-pin 150-mil wide plastic QSOP (Q) - 20-pin 300-mil wide plastic SOIC (S) PI74FCT2541T - 20-pin 150-mil wide plastic QSOP (Q) - 20-pin 300-mil wide plastic SOIC (S) * Device models available upon request 08-0291 1 PS2011G 11/10/08 PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/Line Drivers Block Diagrams PI74FCT244/2244T PI74FCT541/2541T OEA OEA OEB* DA0 OA0 OB0 DB0 DA1 OA1 OB1 DB1 DA2 OA2 OB2 DB2 DA3 OA3 OB3 DB3 OEB D0 O0 D1 O1 D2 O2 D3 O3 D4 O4 D5 O5 D6 O6 D7 O7 *OEB for 244T Truth Table Product Pin Description Pin Name OEA, OEB OEB(1) Dxx Oxx GND VCC Description 3-State Output Enable Inputs (Active LOW) 3-State Output Enable Input (Active HIGH) Inputs Outputs Ground Power OEA L L H 08-0291 20 19 18 17 16 15 14 13 12 11 D L H X 244 L H Z 541 L H Z PI74FCT541/2541T Pin Configuration PI74FCT244/2244T Pin Configuration 1 2 3 4 5 6 7 8 9 10 Outputs(1) Notes: 1. H = High Voltage Level, X = Don't Care, L = Low Voltage Level, Z = High Impedance Notes: 1. Only offered for PI74FCT244T OEA DA0 OB0 DA1 OB1 DA2 OB2 DA3 OB3 GND Inputs(1) OEB OEB(2) L H L H H L OEA D0 D1 D2 D3 D4 D5 D6 D7 GND Vcc OEB OA0 DB0 OA1 DB1 OA2 DB2 OA3 DB3 2 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 Vcc OEB O0* O1* O2* O3* O4* O5* O6* O7* PS2011G 11/10/08 PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/Line Drivers Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ............................................................. -65C to +150C Ambient Temperature with Power Applied .............................-40C to +85C Supply Voltage to Ground Potential (Inputs & Vcc Only) ...... -0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only) ... -0.5V to +7.0V DC Input Voltage ..................................................................... -0.5V to +7.0V DC Output Current................................................................................ 120mA Power Dissipation .................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condi tions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = -40C to +85C, VCC = 5.0V 5%) Parameters Test Conditions(1) Description Min. Typ(2) 2.4 3.0 Max. VOH Output HIGH Voltage VCC = Min., VIN = VIH or VIL IOH = -15.0mA VOL Output LOW Current VCC = Min., VIN = VIH or VIL IOL = 64mA 0.3 0.55 VOL Output LOW Current VCC = Min., VIN = VIH or VIL IOL = 12mA (25Series) 0.3 0.50 VIH Input HIGH Voltage Guaranteed Logic HIGH Level VIL Input LOW Voltage Guaranteed Logic LOW Level IIH Input HIGH Current VCC = Max. VIN = VCC 1 IIL Input LOW Current VCC = Max. VIN = GND -1 IOZH High Impedance VOUT = 2.7V 1 IOZL Output Current VOUT = 0.5V -1 VIK Clamp Diode Voltage VCC = Min., IIN = -18mA IOFF Power Down Disable VCC = GND, VOUT = 4.5V IOS Short Circuit Current Max.(3), VOUT VH Input Hysteresis VCC = MAX. VCC = Units V 2.0 0.8 -0.7 = GND -60 A -1.2 V 100 A -120 mA 200 Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 5.0V, +25C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. Capacitance (TA = 25C, f = 1 MHz) Parameters(1) Description Test Conditions Typ. Max. CIN Input Capacitance VIN = 0V 6 10 COUT Output Capacitance VOUT = 0V 8 12 Units pF Notes: 1. This parameter is determined by device characterization but is not production tested. 08-0291 3 PS2011G 11/10/08 PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/Line Drivers Power Supply Characteristics Parameters ICC ICC ICCD IC Test Conditions(1) Description Min. Typ(2) Max. Units Quiescent Power Supply Current VCC = Max. VIN = GND or VCC 0.1 500 A Supply Current per Input @ TTL HIGH VCC = Max. VIN = 3.4V(3) 0.5 2.5 mA Supply Current per Input per MHz(4) VCC = Max., Outputs Open OEA = OEB = GND or OEA = GND, OEB = VCC One Bit Toggling 50% Duty Cycle VIN = VCC VIN = GND 0.15 0.25 mA/ MHz VIN = VCC VIN = GND 1.5 3.5(5) VIN = 3.4V VIN = GND 1.8 4.5(5) VIN = VCC VIN = GND 3.0 6.0(5) VIN = 3.4V VIN = GND 5.0 14.0(5) Total Power Supply Current(6) VCC = Max., Outputs Open fI = 10 MHZ 50% Duty Cycle OEA = OEB = GND or OEA = GND, OEB = VCC One Bit Toggling VCC = Max., Outputs Open fI = 2.5 MHZ 50% Duty Cycle OEA = OEB = GND or OEA = GND, OEB = VCC Eight Bits Toggling mA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc = 5.0V, +25C ambient. 3. Per TTL driven input (VIN = 3.4V); all other inputs at Vcc or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested. 6. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fCP/2 + fINI) ICC = Quiescent Current ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) fI = Input Frequency NI = Number of Inputs at fI All currents are in milliamps and all frequencies are in megahertz. 08-0291 4 PS2011G 11/10/08 PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/Line Drivers PI74FCT244/2244T Switching Characteristics over Operating Range Parameters 244T/2244T 244AT/2244AT 244CT/2244CT 244DT Com. Com. Com. Com. Conditions(1) Description tPLH tPHL Propagation Delay(2) tPZH tPZL Output Enable Time OEX to ON tPHZ tPLZ Output Disable Time(3) OEX to ON CL = 50pF Units Min Max Min Max Min Max Min Max 1.5 6.5 1.5 4.8 1.5 4.1 1.5 3.6 ns 1.5 8.0 1.5 6.2 1.5 5.8 1.5 4.8 ns 1.5 7.0 1.5 5.6 1.5 5.2 1.5 4.0 ns Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. This parameter is guaranteed but not production tested. PI74FCT541/2541T Switching Characteristics over Operating Range Parameters Description Conditions(1) Delay(2) tPLH tPHL Propagation DN to ON tPZH tPZL Output Enable Time OEX to ON tPHZ tPLZ Output Disable Time(3) OEX to ON CL = 50pF RL = 500 541T/2541T 541AT/ 2541AT 541CT/ 2541CT 541DT Com. Com. Com. Com. Units Min Max Min Max Min Max Min Max 1.5 6.0 1.5 4.8 1.5 4.1 1.5 3.8 ns 1.5 9.5 1.5 6.2 1.5 5.8 1.5 5.2 ns 1.5 6.5 1.5 5.6 1.5 5.2 1.5 5.2 ns Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. This parameter is guaranteed but not production tested. 08-0291 5 PS2011G 11/10/08 PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/Line Drivers Ordering Information: PI74FCT244T Ordering Code PI74FCT244TH PI74FCT244THE PI74FCT244TL PI74FCT244TLE PI74FCT244ATQE PI74FCT244ATSE PI74FCT244CTH PI74FCT244CTHE PI74FCT244DTQ PI74FCT244DTSE PI74FCT244TQE Package Code H H L L Q S H H Q S Q Speed Grade Blank Blank Blank Blank A A C C D D Blank Package Description 20-pin 209-mil wide plastic SSOP Pb-free & Green, 20-pin 209-mil wide plastic SSOP 20-pin 173-mil wide plastic TSSOP Pb-free & Green, 20-pin 173-mil wide plastic TSSOP Pb-free & Green, 20-pin 150-mil wide plastic QSOP Pb-free & Green, 20-pin 300-mil wide plastic SOIC 20-pin 209-mil wide plastic SSOP Pb-free & Green, 20-pin 209-mil wide plastic SSOP 20-pin 150-mil wide plastic QSOP Pb-free & Green, 20-pin 300-mil wide plastic SOIC Pb-free & Green, 20-pin 150-mil wide plastic QSOP PI74FCT244CTQE Q C Pb-free & Green, 20-pin 150-mil wide plastic QSOP PI74FCT244DTQE Q C Pb-free & Green, 20-pin 150-mil wide plastic QSOP PI74FCT244CTSE S C Pb-free & Green, 20-pin 300-mil wide plastic SOIC PI74FCT244TQE Q Pb-free & Green, 20-pin 150-mil wide plastic QSOP PI74FCT244TQSE Q Pb-free & Green, 20-pin, Tape/Reel, 150-mil wide plastic QSOP Notes: * Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ * E = Pb-free and Green * Adding an X suffix = Tape/Reel 08-0291 6 PS2011G 11/10/08 PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/Line Drivers Ordering Information: PI74FCT2244T Ordering Code PI74FCT2244TQE PI74FCT2244TSE PI74FCT2244ATLE PI74FCT2244ATQE PI74FCT2244ATSE PI74FCT2244CTQE Package Code Q S L Q S Q Speed Grade Blank Blank A A A C Package Description Pb-free & Green, 20-pin 150 mil wide plastic QSOP Pb-free & Green, 20-pin 300 mil wide plastic SOIC Pb-free & Green, 20-pin 173 mil wide plastic TSSOP Pb-free & Green, 20-pin 150 mil wide plastic QSOP Pb-free & Green, 20-pin 300 mil wide plastic SOIC Pb-free & Green, 20-pin 150 mil wide plastic QSOP Speed Grade A C Blank Blank A A A Blank Package Description Pb-free & Green, 20-pin 150-mil wide plastic QSOP Pb-free & Green, 20-pin 173-mil wide plastic TSSOP Pb-free & Green, 20-pin 150-mil wide plastic QSOP 20-pin 300-mil wide plastic SOIC 20-pin 150-mil wide plastic QSOP 20-pin 300-mil wide plastic SOIC Pb-free & Green, 20-pin 300-mil wide plastic SOIC Pb-free & Green, 20-pin 300-mil wide plastic SOIC Speed Grade Blank Blank A A A A Package Description 20-pin 150 mil wide plastic QSOP Pb-free & Green, 20-pin 300 mil wide plastic SOIC 20-pin 150 mil wide plastic QSOP 20-pin 300 mil wide plastic SOIC Pb-free & Green, 20-pin 300 mil wide plastic SOIC Pb-free & Green, 20-pin 150 mil wide plastic QSOP Ordering Information: PI74FCT541T Ordering Code PI74FCT541ATQE PI74FCT541CTLE PI74FCT541TQE PI74FCT541TS PI74FCT541ATQ PI74FCT541ATS PI74FCT541ATSE PI74FCT541TSE Package Code Q L Q S Q S S T Ordering Information: PI74FCT2541T Ordering Code PI74FCT2541TQ PI74FCT2541TSE PI74FCT2541ATQ PI74FCT2541ATS PI74FCT2541ATSE PI74FCT2541ATQE Package Code Q S Q S S Q Notes: * Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ * E = Pb-free and Green * Adding an X suffix = Tape/Reel 08-0291 7 PS2011G 11/10/08 PI74FCT244T/2244T PI74FCT541T/2541T Fast CMOS Non-Inverting Octal Buffer/Line Drivers Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com 08-0291 8 PS2011G 11/10/08