Standard Products VRG8609/10 Dual Adjustable Negative Voltage Regulators Radiation Tolerant www.aeroflex.com/voltreg September 9, 2011 FEATURES Manufactured using Linear Technology Corporation (R) Space Qualified RH137 die Radiation performance Load regulation: 1.0% max - Total dose: 100 krads(Si), Line regulation: 0.05% max Dose rate = 50 - 300 rads(Si)/s Ripple rejection: >66dB - ELDRS: 50 kreds(Si), Packaging - Hermetic metal Dose rate < 10 mrads(Si)/S - Thru-hole or Surface mount Thermal shutdown - 6 Leads, .655"L x .415"W x .200"Ht Output voltage adjustable: -1.25V to -27V - Power package 3-Terminal - Weight - 5 gm max Output current: 1.5A Designed for aerospace and high reliability space Voltage reference: -1.25V applications Aeroflex Plainview's Radiation Hardness Assurance Plan is DLA Certified to MIL-PRF-38534, Appendix G. DESCRIPTION The Aeroflex Plainview VRG8609/10 consists of two negative (RH137) voltage regulators each capable of supplying in excess of 1.5Amps over the output voltage range as defined under recommended operating conditions. Each regulator is exceptionally easy to set-up, requiring only 2 external resistors to set the output voltage. The module design has been optimized for excellent regulation and low thermal transients. There is full electrical isolation between the regulators and each regulator to the package. Further, the VRG8609/10 features internal current limiting, thermal shutdown and safe-area compensation, making them virtually blowout-proof against overloads. The VRG8609/10 serves a wide variety of applications including local on-card regulation, programmable output voltage regulation or precision current regulation. The VRG8609/10 has been specifically designed to meet exposure to radiation environments. The VRG8609 is configured for a Thru-Hole 6 lead metal power package and the VRG8610 is configured for a Surface Mount 6 lead metal power package. It is guaranteed operational from -55C to +125C. Available screened to MIL-STD-883, the VRG8609/10 is ideal for demanding military and space applications. For detailed performance characteristic curves, applications information and typical applications see the latest Linear Technology Corporation (R) data sheets for their RH/LT137, which is available on-line at www.linear.com. 1 4 ADJ 2 ADJ VOUT VOUT RH137 Negative Regulator RH137 Negative Regulator VIN VIN 3 SCD8609 Rev E 6 5 FIGURE 1 - BLOCK DIAGRAM / SCHEMATIC ABSOLUTE MAXIMUM RATINGS PARAMETER Operating (Junction) Temperature Range RANGE UNITS -55 to +150 C 300 C -65 to +150 C 30 (Neg) V Lead Temperature (soldering, 10 sec) Storage Temperature Range Input-Output Voltage Differential Thermal Resistance (junction to case JC) each, Pos. & Neg. ESD Rating 5 C/W 1.999 1/ KV 1/ Meets ESD testing per MIL-STD-883, method 3015, Class 1C. NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating only; functional operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions" may effect device reliability. RECOMMENDED OPERATING CONDITIONS PARAMETER RANGE UNITS Output Voltage Range -1.3 to -27 VDC Case Operating Temperature Range -55 to +125 C ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ PARAMETER Reference Voltage 4/ SYM CONDITIONS (P PMAX MIN MAX UNITS VREF 3V < (VIN - VOUT) < VDIFF MAX, 10mA < IOUT < IMAX -1.200 -1.300 V Line Regulation 2/, 4/ VOUT VIN 3V < (VIN - VOUT) < 30V, - 0.05 %/V Load Regulation 2/, 4/ VOUT IOUT 10mA < IOUT < IMAX, VOUT < 5V 10mA < IOUT < IMAX, VOUT > 5V - 50 1.0 mV % Thermal Regulation IOUT = 1.5A, (VIN - VOUT) = 13.3V, 20ms Pulse, 20W, TC = +25C - 0.02 %/W Ripple Rejection VOUT = -10V, f = 120Hz, CADJ = 10F 66 - dB IOUT = 10mA, 3V < (VIN - VOUT) < 30V - 100 A 3V < (VIN - VOUT) < 30V, 10mA < IOUT < IMAX - 5 A (VIN - VOUT) = 30V - 5 (VIN - VOUT) < 10V - 3 (VIN - VOUT) < 15V 1.5 - (VIN - VOUT) = 30V, TC = +25C 0.24 - - 1 % - 5 C/W Adjustment Pin Current 4/ IADJ Adjustment Pin Current Change 4/ IADJ Minimum Load Current 3/ 4/ IMIN Current Limit 4/, 5/ IMAX Long Term Stability 3/ Thermal Resistance, each Regulator (Junction to Case) 3/ VOUT TIME TC = +125C JC mA A Notes: 1/ Unless otherwise specified, these specifications apply for, (Vin - Vout) = 5V, Iout = 0.5A and -55C < Tc < +125C. 2/ Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are covered under the specification for thermal regulation. Measurements taken at the output lead must be adjusted for lead resistance. 3/ Not tested. Shall be guaranteed to the specified limits. 4/ Specification derated to reflect High Dose Rate (1019 condition A) to 100krads(Si) and Low Dose Rate (1019 condition D) to 50krads(Si), @ +25C. 5/ Pulsed @ < 10% duty cycle @ +25C. SCD8609 Rev E 9/9/11 2 Aeroflex Plainview 60 50 40 Maximum Power Dissipation (Watts) 30 Both Regulators 20 1 Regulator 10 0 0 20 40 60 80 100 120 140 Case Temperature (C) FIGURE 2 - MAXIMUM POWER vs CASE TEMPERATURE The maximum Power dissipation is limited by the thermal shutdown function of each regulator chip in the VRG8609/10. The graph above represents the achievable power before the chip shuts down. The first line in the graph represents the maximum power dissipation of the VRG8609/10 with one regulator on (the other off) and the other line represents both regulators on dissipating equal power. If both regulators are on and one regulator is dissipating more power that the other, the maximum power dissipation of the VRG8609/10 will fall between the two lines. This graph is based on the maximum junction temperature of 150C and a thermal resistance (JC) of 5C/W. VIN VRG8609/10 VOUT VREF R1 ADJ VREF = 1.25V, IADJ = 50A -Reg = VOUT = -VREF (1+R2/R1) + (-IADJ x R2) R2 Adjustable Regulator FIGURE 3 - TYPICAL APPLICATIONS SCD8609 Rev E 9/9/11 3 Aeroflex Plainview TABLE I - PIN NUMBERS vs FUNCTION PIN FUNCTION 1 NEG_ADJ_1 2 NEG_VOUT_1 3 NEG_VIN_1 4 NEG_ADJ_2 5 NEG_VIN_2 6 NEG_VOUT_2 .200 .100 .108 .123 o .010 M CBA .150 REF. o.145 THRU 2x .028 MAX. 6 5 2 MAX. TYP. 4 .720 .020 MEASURED LEAD TIP .415 .2075 -C- 1 2 3 ESD/PIN 1 IDENT .230 MIN .415 SQ R.065 TYP. 4 PLCS .655 -B- .122 .003 o .010 BCA .220 MAX. .005 -A- .040 Notes: 1. Dimension Tolerance: .005 inches 2. Package contains BeO substrate 3. Case electrically isolated .030 DIA. .002 o .010 M CBA FIGURE 4 - PACKAGE OUTLINE -- THRU-HOLE POWER PACKAGE SCD8609 Rev E 9/9/11 4 Aeroflex Plainview TABLE II - PIN NUMBERS vs FUNCTION PIN FUNCTION 1 NEG_ADJ_1 2 NEG_VOUT_1 3 NEG_VIN_1 4 NEG_ADJ_2 5 NEG_VIN_2 6 NEG_VOUT_2 .200 .100 .108 .123 o .010 .150 REF. CBA o.145 THRU 2x .028 MAX. M 6 5 .060 4 .415 .886 .020 .2075 -C- 1 2 3 ESD/PIN 1 IDENT .415 SQ R.065 TYP. 4 PLCS .655 -B- .122 .003 o .010 BCA .220 MAX. .005 -A- .020 .040 .030 DIA. .002 o .010 M CBA Notes: 1. Dimension Tolerance: .005 inches 2. Package contains BeO substrate 3. Case electrically isolated FIGURE 5 - PACKAGE OUTLINE -- SURFACE MOUNT POWER PACKAGE SCD8609 Rev E 9/9/11 5 Aeroflex Plainview ORDERING INFORMATION MODEL DLA SMD # SCREENING VRG8609-7 - Commercial Flow, +25C testing only VRG8609-S - Military Temperature, -55C to +125C Screened in accordance with the individual Test Methods of MIL-STD-883 for Space Applications VRG8609-201-1S 5962-0521904KXC VRG8609-201-2S 5962-0521904KXA VRG8609-901-1S 5962R0521904KXC VRG8609-901-2S 5962R0521904KXA In accordance with DLA Certified RHA Program Plan to RHA level "R", 100 krads(Si) VRG8610-7 - Commercial Flow, +25C testing only VRG8610-S - Military Temperature, -55C to +125C Screened in accordance with the individual Test Methods of MIL-STD-883 for Space Applications In accordance with DLA SMD VRG8610-201-1S 5962-0521904KYC VRG8610-201-2S 5962-0521904KYA VRG8610-901-1S 5962R0521904KYC VRG8610-901-2S 5962R0521904KYA In accordance with DLA SMD PACKAGE 6 Lead Thru-Hole Power Pkg 6 Lead Surface Mount Power Pkg In accordance with DLA Certified RHA Program Plan to RHA level "R", 100 krads(Si) EXPORT CONTROL: EXPORT WARNING: This product is controlled for export under the International Traffic in Arms Regulations (ITAR). A license from the U.S. Department of State is required prior to the export of this product from the United States. Aeroflex's military and space products are controlled for export under the International Traffic in Arms Regulations (ITAR) and may not be sold or proposed or offered for sale to certain countries. (See ITAR 126.1 for complete information.) PLAINVIEW, NEW YORK Toll Free: 800-THE-1553 Fax: 516-694-6715 INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 SE AND MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468 www.aeroflex.com info-ams@aeroflex.com Aeroflex Microelectronic Solutions reserves the right to change at any time without notice the specifications, design, function, or form of its products described herein. All parameters must be validated for each customer's application by engineering. No liability is assumed as a result of use of this product. No patent licenses are implied. Our passion for performance is defined by three attributes represented by these three icons: solution-minded, performance-driven and customer-focused and the Linear Technology logo are registered trademarks and RH137 are a copyright of Linear Technology Corporation. SCD8609 Rev E 9/9/11 6