G6AK-274P-STLT-US-DC12 - Omron

Low Signal Relay G6A 67

Low Signal Relay

G6A

Fullly Sealed Relay with High Impulse Withstand

• High sensitivity — can be driven by digital circuits.

• Low-profile design allows use in 12.70 mm PC board rack.

• Surge withstand voltage meets FCC Part 68 regulation.

• Units can be mounted side by side due to low magnetic

leakage.

• Special models available for low thermoelectromotive force.

• Unique moving loop (permanent magnet) armature reduces

relay size, magnetic interference, and contact bounce time.

• Single or dual coil winding types available.

• RoHS Compliant

RC FCC

Ordering Information

To Order: Select the part number and add the desired coil voltage rating, (e.g., G6A-274P-ST-US-DC12).

■Non-latching

■Latching

Single Coil

Dual Coil

Type Contact form Model

Ag (Au clad)

Standard DPDT G6A-274P-ST-US

Low-sensitivity DPDT G6A-274P-ST40-US

Type Contact form Model

Ag (Au clad)

Standard DPDT G6AU-274P-ST-US

Type Contact form Model

Ag (Au clad)

Standard DPDT G6AK-274P-ST-US

Low-sensitivity DPDT G6AK-274P-ST40-US

68 Low Signal Relay G6A

Specifications

■Contact Data

* 0.25A at 125VAC for latching models

Note: P level: λ60 = 0.1 x 10–6/operation

This value was measured at a switching frequency of 60 operations/min and the criterion of contact resistance is 50 Ω. This value may vary

depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions.

■Coil Data

Standard Non-latching DPDT (G6A-274P-ST-US)

Low-sensitivity Non-latching DPDT (G6A-274P-ST40-US)

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.

2. Operating characteristics are measured at a coil temperature of 23°C.

3. The maximum voltage is the highest voltage that can be imposed on the relay coil.

Type G6A-274P-ST(40)-US

G6AK-274P-ST(40)-US

G6AU-274P-ST-US

Load Resistive load (p.f. = 1) Inductive load (p.f. = 0.4)

(L/R = 7 ms)

Rated load 0.50 A at 125 VAC,

2 A at 30 VDC

0.3 A* at 125 VAC,

1 A at 30 VDC

Contact material Ag (Au clad)

Carry current 3 A

Max. operating voltage 250 VAC, 220 VDC

Max. operating current 2 A 1 A

Max. switching capacity 125 VA, 60 W 62.50 VA, 30 W

Min. permissible load (See note) 10 μA, 10 mVDC

Rated

voltage

(VDC)

Rated

current

(mA)

Coil

resistance

(Ω)

Coil inductance

(ref. value) (H)

Pick-up

voltage

Dropout

voltage

Maximum

voltage

Power

consumption

(mW)

Armature

OFF

Armature

% of rated voltage

3 66.70 45 0.07 0.065 70% max. 10% min. 200%

at 23°C

Approx. 200

4.5 44.6 101 0.16 0.14

5 40 125 0.20 0.18

6 33.30 180 0.29 0.26

9 22.20 405 0.63 0.57

12 16.70 720 1.10 1.06

24 8.30 2,880 4.50 4.10

48 4.90 9,750 13.70 12.50 Approx. 235

Rated

voltage

(VDC)

Rated

current

(mA)

Coil

resistance

(Ω)

Coil inductance

(ref. value) (H)

Pick-up

voltage

Dropout

voltage

Maximum

voltage

Power

consumption

(mW)

Armature

OFF

Armature

% of rated voltage

3 133.30 22.50 0.03 0.02 70% max. 10% min. 150%

at 23°C

Approx. 400

4.5 88.9 50.6 0.065 0.06

5 80 62.50 0.08 0.07

6 66.70 90 0.11 0.10

9 44.30 203 0.27 0.23

12 33.30 360 0.52 0.43

24 16.70 1,440 2.10 1.80

48 8.30 5,760 7.50 6.40

Low Signal Relay G6A 69

Standard Single Coil Latching DPDT (G6AU-274P-ST-US)

Standard Dual Coil Latching DPDT (G6AK-274P-ST-US)

Low-sensitivity Dual Coil Latching DPDT (G6AK-274P-ST40-US)

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.

2. Operating characteristics are measured at a coil temperature of 23°C.

3. The maximum voltage is the highest voltage that can be imposed on the relay coil.

Rated

voltage

(VDC)

Rated

current

(mA)

Coil

resistance

(Ω)

Coil inductance

(ref. value) (H)

Set pick-up

voltage

Reset pick-

up voltage

Maximum

voltage

Power

consumption

(mW)

Armature OFF Armature ON % of rated voltage

3 33.70 89 0.15 0.11 70% max. 70% min. 200%

at 23°C

Approx. 100

4.5 22.2 202 0.34 0.25

5 20 250 0.44 0.35

6 16.70 360 0.64 0.48

9 11.10 810 1.38 1.07

12 8.30 1,440 2.50 2

24 4.20 5,760 9.20 7.20

48 2.50 19,000 28.50 22 Approx. 120

Rated

voltage

(VDC)

Rated

current

(mA)

Coil

resistance

(Ω)

Coil inductance

(ref. value) (H)

Set

pick-up

voltage

Reset

pick-up

voltage

Maximum

voltage

Power

consumption

(mW)

Set coil Reset coil

Armature

OFF

Armature

OFF

Armature

% of rated voltage

3 66.70 45 0.037 0.027 0.027 0.037 70% max. 70% min. 200%

at 23°C

Approx. 200

4.5 40.2 112 0.09 0.065 0.065 0.09 Approx. 180

5 36 139 0.11 0.08 0.08 0.11

6 30 200 0.16 0.12 0.12 0.16

9 20 450 0.38 0.28 0.28 0.38

12 15 800 0.60 0.45 0.45 0.60

24 7.50 3,200 2.10 1.50 1.50 2.10

48 4.20 11,520 8.50 6.30 6.30 8.50 Approx. 200

Rated

voltage

(VDC)

Rated

current

(mA)

Coil

resistance

(Ω)

Coil inductance (ref. value) (H) Set

pick-up

voltage

Reset

pick-up

voltage

Maximum

voltage

Power

consumption

(mW)

Set coil Reset coil

Armature

OFF

Armature

OFF

Armature

% of rated voltage

3 120 25 0.015 0.01 0.01 0.015 70% max. 70% min. 150%

at 23°C

Approx. 360

4.5 79.9 56.3 0.04 0.025 0.025 0.04

5 72.50 69 0.05 0.035 0.035 0.05

6 60 100 0.07 0.05 0.05 0.07

9 40 225 0.16 0.12 0.12 0.16

12 30 400 0.28 0.20 0.20 0.28

24 15 1,600 1.10 0.75 0.75 1.10

48 7.50 6,400 4 2.90 2.9 4

70 Low Signal Relay G6A

■Characteristics

Note: 1. The contact resistance was measured with 10 mA at 1 VDC with a fall-of-potential method.

2. Values in parentheses are typical values unless otherwise stated.

The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength

(except between the set and reset coil).

4. The above values are initial values.

■Approvals

UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C

Note: 1. The rated values approved by each of the safety standards (e.g., UL and CSA) may be different from the performance characteristics

individually defined in this catalog.

2. In the general interest of product improvement, specifications are subject to change.

Type Non-latching Latching

Contact resistance (See note 1) 50 mΩ max.

Operate (set) time

(See note 2)

DPDT 5 ms max. (mean value approx. 3 ms) 5 ms max. (mean value approx. 2.50 ms)

Release (reset) time

(See note 2)

DPDT 3 ms max. (mean value approx. 1.20 ms) 5 ms max. (mean value approx. 2.50 ms)

Min. set/reset signal width DPDT 7 ms min.

Operating frequency Mechanical 36,000 operations/hour

Electrical 1,800 operations/hour (under rated load)

Insulation resistance (See note 3) 1,000 MΩ min. (at 500 VDC); except for set-reset

Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between coil and contacts

1,000 VAC, 50/60 Hz for 1 minute between contacts of different poles

1,000 VAC, 50/60 Hz for 1 minute between contacts of same pole

250 VAC, 50/60 Hz for 1 minute between set and reset coils

Surge withstand voltage 1,500 V (10 x 160 μs) (conforms to FCC Part 68)

Vibration Mechanical durability 10 to 55 Hz; 5 mm double amplitude

Malfunction durability 10 to 55 Hz; 3.3 mm double amplitude

Shock Mechanical durability 1,000 m/s2 (Approx. 100G

Malfunction durability DPDT: 500 m/s2 (Approx. 50 G)

Ambient temperature -40° to 70°C with no icing

Humidity 5% to 85% RH

Service life Mechanical 100 million operations min. (at 36,000 operations/hour)

Electrical 500,000 operations min. (at 1,800 operations/hr) See “Characteristic Data”

Weight DPDT Approx. 3.5 g

4PDT Approx. 6.0 g

Type Contact form Coil rating Contact ratings Number of test operations

G6A( )-274P-ST( )-US DPDT 1.5 to 48 VDC 1 A at 125 VAC (General Purpose)

2 A at 30 VDC (General Purpose)

0.6 A at 110 VDC (General Purpose)

6,000

Low Signal Relay G6A 71

■Characteristic Data

Maximum Switching Capacity

DPDT

Ambient Temperature vs.

Maximum Coil Voltage

Switching current (A)

Rated Operating voltage (V)Ambient temperature (°C)

Maximum coil voltage (%)

DC inductive

(L/R = 7 ms)

AC inductive

(cosf = 0.4)

DC resistive

AC resistive

DPDT: 360, 400 mW

DPDT: 100, 180, 200 mW

Note: The maximum coil voltage refers

to the maximum value in a varying

range of operating power voltage,

not a continuous voltage.

Electrical Service Life

DPDT

Rated operating current (A)

Service Life (x10 operations)

-234P 30 VDC, resistive;

-274P 30 VDC, inductive

-274P 30 VDC, resistive

-234P 125 VAC,

resistive

-274P 125 VAC,

resistive;

-234P 30 VDC,

inductive

234P 125 VAC,

inductive-274P 125 VAC,

inductive

100

0.5

0.3

0.1

0.05

0.03

72 Low Signal Relay G6A

Dimensions

Note: 1. All units are in millimeters unless otherwise indicated.

2. Orientation marks are indicated as follows:

■Non-latching

G6A-274P-ST(40)-US

■Latching

G6AU-274P-ST-US

G6AK-274P-ST(40)-US

Precautions

Long-term Continuously ON Contacts

Using the Relay in a circuit where the Relay will be ON continuously

for long periods (without switching) can lead to unstable contacts

because the heat generated by the coil itself will affect the insulation,

causing a film to develop on the contact surfaces. Be sure to use a

fail-safe circuit design that provides protection against contact failure

or coil burnout. Otherwise, use a latching relay.

Relay Handling

When washing the product after soldering the Relay to a PCB, use a

water-based solvent or alcohol-based solvent, and keep the solvent

temperature to less than 40°C. Do not put the Relay in a cold clean-

ing bath immediately after soldering.

Terminal Arrangement/

Internal Connections

(Bottom View)

Mounting Holes

(Bottom View)

Tolerance: ±0.1

7.62 5.085.08

(1.2)

7.62

(1.2)

Eight, 1.0-dia. holes

20.2 max.

(20)*

0.6

10.1 max.

(9.9)*

8.4 max.

(8.2)*

0.64

7.62

0.3 3.16

*Average value

20.2 max.

(20)*

0.6

10.1 max.

(9.9)*

8.4 max.

(8.2)*

0.64

7.62

0.3 3.16

Terminal Arrangement/

Internal Connections

(Bottom View)

Mounting Holes

(Bottom View)

Tolerance: ±0.1

+ -

- +

S R

7.62 5.085.08

(1.2)

7.62

(1.2)

Eight, 1.0-dia. holes

*Average value

20.2 max.

(20)*

0.6

10.1 max.

(9.9)*

8.4 max.

(8.2)*

0.64

7.62

0.3 3.16

Terminal Arrangement/

Internal Connections

(Bottom View)

Mounting Holes

(Bottom View)

Tolerance: ±0.1

2.54 5.085.08

(1.2)

7.62

(1.2)

5.08

Ten, 1-dia. holes

*Average value

Low Signal Relay G6A

MEMO

Low Signal Relay G6A

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

Cat. No. X301-E-1b Printed in USA

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B

Schaumburg, IL 60173

847-882-2288

09/11 Specifications subject to change without notice

All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which

can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.