TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 N-CHANNEL LOGIC LEVEL MOSFET Qualified per MIL-PRF-19500/570 DEVICES LEVELS 2N6901 JAN JANTX JANTXV ABSOLUTE MAXIMUM RATINGS (TC = +25C unless otherwise noted) Parameters / Test Conditions Symbol Value Unit Drain - Source Voltage VDS 100 Vdc Gate - Source Voltage Continuous Drain Current VGS 10 Vdc ID1 1.69 Adc ID2 1.07 Adc Ptl 8.33 (1) W TC = +25C Continuous Drain Current TC = +100C Max. Power Dissipation Drain to Source On State Resistance Operating & Storage Temperature Rds(on) Top, Tstg 1.4 (2) -55 to +150 C Note: (1) Derated Linearly by 0.067 W/C for TC > +25C (2) VGS = 5Vdc, ID = 1.07A 2N6901 TO-205AF (formerly TO-39) SEE FIGURE 1 ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions Symbol Min. V(BR)DSS 100 VGS(th)1 VGS(th)2 VGS(th)3 1.0 0.5 Max. Unit OFF CHARACTERTICS Drain-Source Breakdown Voltage VGS = 0V, ID = -1mAdc Gate-Source Voltage (Threshold) VDS VGS, ID = 1.0mA VDS VGS, ID = 1.0mA, Tj = +125C VDS VGS, ID = 1.0mA, Tj = -55C Gate Current VGS = 10V, VDS = 0V VGS = 10V, VDS = 0V, Tj = +125C Vdc 2.0 Vdc 3.0 IGSS1 IGSS2 100 200 nAdc Drain Current VGS = 0V, VDS = 80V VGS = 0V, VDS = 80V, Tj = +125C Static Drain-Source On-State Resistance VGS = 5V, ID = 1.07A pulsed IDSS1 IDSS2 1.0 50.0 Adc uAdc rDS(on)1 1.4 Tj = -125C VGS = 5V, ID = 1.07A pulsed rDS(on)2 2.6 1.6 Vdc Diode Forward Voltage VGS = 0V, ID = 1.69A pulsed T4-LDS-0188 Rev. 1 (101985) VSD 0.8 Page 1 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 DYNAMIC CHARACTERISTICS Parameters / Test Conditions Gate Charge: On-State Gate Charge Gate to Source Charge Gate to Drain Charge Symbol VGS = 5V, ID = 1.69A VDS = 50V Min. Qg(on) Qgs Qgd Max. 5.0 1.0 2.9 Unit nC SWITCHING CHARACTERISTICS Parameters / Test Conditions Switching time tests: Turn-on delay time Rinse time Turn-off delay time Fall time Diode Reverse Recovery Time T4-LDS-0188 Rev. 1 (101985) Symbol ID = 1.69A, VGS = 5Vdc, Gate drive impedance = 25, VDD = 50Vdc di/dt 100A/s, VDD 30V, IF = 1.0A Min. Max. td(on) tr td(off) tf 25 80 45 80 trr 250 Unit ns ns Page 2 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Symbol CD CH HD LC LD LL LU L1 L2 P Q TL TW r NOTE: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Dimensions Inches Millimeters Min Max Min Max .305 .335 7.75 8.51 .160 .180 4.07 4.57 .335 .370 8.51 9.40 .200 TP 5.08 TP .016 .021 0.41 0.53 .500 .750 12.70 19.05 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .100 2.54 .050 1.27 .029 .045 0.74 1.14 .028 .034 0.71 0.86 .010 0.25 45 TP 45 TP 8,9 8,9 8,9 8,9 8,9 6 5 4 3 10 6 Dimensions are in inches. Millimeters are given for general information only. Beyond radius(r) maximum, TW shall be held for a minimum length of .011 (0.28 mm). Dimension TL measured from maximum HD. Outline in this zone is not controlled. Dimension CD shall not vary more than .010 (0.25 mm) in zone P. This zone is controlled for automatic handling. Leads at gauge plane .054 +.001, -.000 (1.37 +0.03, -0.00 mm) below seating plane shall be within .007 (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. LU applies between L1 and L2. LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. All three leads. Radius(r) applies to both inside corners of tab. Drain is electrically connected to the case. Pin out: 1- source, 2 - gate, 3 - drain (case). In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 1. Physical dimensions for TO-205 AF T4-LDS-0188 Rev. 1 (101985) Page 3 of 3