ASDL-4561 High Performance Infrared Emitter (870nm) ChipLED Data Sheet Description Features ASDL-4561 Infrared emitter is a 0603 ChipLED SMT package that is designed for applications with low space requirements and high radiant intensity coupled with high speed. It is optimized for efficiency at emission wavelength of 870nm and encapsulated with a flat lens for wide viewing angle applications. * 870nm wavelength * Industry Standard Footprint: 0603 ChipLED SMT Package * Top Emitting * Low Forward Voltage * High Pulse Rate * High Speed Applications * High-Speed Machine Automated System * Remote Control * Wide Viewing Angle * Lead Free and ROHS Compliant * Tape & Reel for automation placement * Smoke Detector * Medical Applications * Non-Contact Position Sensing * Optical Encoders Ordering Information Part Number Packaging Shipping Option ASDL-4651-C22 Tape & Reel 12Kpcs Package Outline All Dimensions are in Millimeters Tape and Reel Dimension All Dimensions are in Millimeters (Inches) Absolute Maximum Ratings at 25C Parameter Symbol Peak Forward Current Min. Max Unit Reference IFPK 300 mA Tp=500ns Tw=100ns Duty Cycle=20% Continuous Forward Current IFDC 60 mA Power Dissipation PDISS 120 mW Reverse Voltage Vr 11 Operating Temperature TO -40 LED Junction Temperature TJ Lead Soldering Temperature V Ir=100uA 85 C 110 C 260 for 5 sec C Typ. Max. Unit Condition 1.3 1.35 1.75 1.85 V V IF=20mA IF=50mA V IR=100uA Electrical Characteristics at 25C Parameter Symbol Forward Voltage VF Reverse Voltage Vr Min. 11 Thermal Resistance Diode Capacitance CO 400 C/W 50 pF Vr=0V, f=1MHz Optical Characteristics at 25C Parameter Symbol Min. Typ. Radiant On-Axis Intensity IE 1.64 Viewing Angle Max. Unit Condition 2.2 mW/Sr IF=50mA 21/2 150 deg Peak wavelength PK 870 nm IF = 50mA Spectral Width 45 nm IF = 50mA Optical Rise Time tr 20 ns IFPK=500mA Duty Factor=20% Pulse Width=100ns Optical Fall Time tf 17 ns IFPK=500mA Duty Factor=20% Pulse Width=100ns 1.2 0.12 1.0 0.10 If Forward Current (A) Relative Radiant Intensity Typical Electrical / Optical Characteristics Curve (TA = 25C Unless Otherwise Stated) 0.8 0.6 0.4 0.08 0.06 0.04 0.02 0.2 0 700 800 900 0 1000 0 0.5 1 Vf Forward Voltage (V) Peak Wavelength (nm) Figure 2. Forward Current Vs Forward Voltage 5 1 4 0.8 Ie - Relative Radiant Intensity Radiant Intensity (mW/Sr) Figure 1. Peak Wavelength Vs Relative Radiant Intensity 3 2 1 0 0 20 40 60 80 Forward Current (mA) 100 120 I DC MAX - MAXIMUM DC CURRENT PER SEGMENT - mA Figure 3. Forward Current Vs Radiant Intensity 60 55 50 45 40 35 30 25 20 15 10 5 0 20 40 60 o TA - AMBIENT TEMPERATURE - C 80 100 Figure 5. Forward Current versus Ambient Temperature derated based on Tj - 110 C and thermal resistance at 400 C/W -0.8 0.6 0.4 0.2 -0.6 -0.4 -0.2 0 0.0 0.2 0.4 Figure 4.Angular Displacement Vs Relative Radiant Intensity 65 0 1.5 0.6 0.8 Recommended Reflow Profile MAX 260C T - TEMPERATURE (C) 255 R3 230 217 200 180 R2 R4 60 sec to 90 sec Above 217 C 150 R5 R1 120 80 25 0 P1 HEAT UP 50 100 P2 SOLDER PASTE DRY 150 200 P3 SOLDER REFLOW 250 300 t-TIME (SECONDS) P4 COOL DOWN Symbol DT Maximum DT/Dtime or Duration Heat Up P1, R1 25C to 150C 3C/s Solder Paste Dry P2, R2 150C to 200C 100s to 180s Solder Reflow P3, R3 P3, R4 200C to 260C 260C to 200C 3C/s -6C/s Cool Down P4, R5 200C to 25C -6C/s > 217C 60s to 90s Process Zone Time maintained above liquidus point , 217C Peak Temperature 260C - - 20s to 40s 25C to 260C 8mins Time within 5C of actual Peak Temperature Time 25C to Peak Temperature The reflow profile is a straight-line representation of a nominal temperature profile for a convective reflow solder process. The temperature profile is divided into four process zones, each with different DT/Dtime temperature change rates or duration. The DT/Dtime rates or duration are detailed in the above table. The temperatures are measured at the component to printed circuit board connections. In process zone P1, the PC board and component pins are heated to a temperature of 150C to activate the flux in the solder paste. The temperature ramp up rate, R1, is limited to 3C per second to allow for even heating of both the PC board and component pins. Process zone P2 should be of sufficient time duration (100 to 180 seconds) to dry the solder paste. The temperature is raised to a level just below the liquidus point of the solder. Process zone P3 is the solder reflow zone. In zone P3, the temperature is quickly raised above the liquidus point of solder to 260C (500F) for optimum results. The dwell time above the liquidus point of solder should be between 60 and 90 seconds. This is to assure proper coalescing of the solder paste into liquid solder and the formation of good solder connections. Beyond the recommended dwell time the intermetallic growth within the solder connections becomes excessive, resulting in the formation of weak and unreliable connections. The temperature is then rapidly reduced to a point below the solidus temperature of the solder to allow the solder within the connections to freeze solid. Process zone P4 is the cool down after solder freeze. The cool down rate, R5, from the liquidus point of the solder to 25C (77F) should not exceed 6C per second maximum. This limitation is necessary to allow the PC board and component pins to change dimensions evenly, putting minimal stresses on the component. It is recommended to perform reflow soldering no more than twice. Recommended Land Pattern All Dimensions are in Millimeters (Inches) For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright (c) 2007 Avago Technologies Limited. All rights reserved. AV02-0276EN - April 27, 2007