FEATURES FUNCTIONAL BLOCK DIAGRAM VDD High relative accuracy (INL): 2 LSB maximum at 16 bits Low drift 2.5 V reference: 2 ppm/C typical Tiny package: 3 mm x 3 mm, 16-lead LFCSP TUE: 0.1% of FSR maximum Offset error: 1.5 mV maximum Gain error: 0.1% of FSR maximum High drive capability: 20 mA, 0.5 V from supply rails User-selectable gain of 1 or 2 (GAIN pin) Reset to zero scale or midscale (RSTSEL pin) 1.8 V logic compatibility 50 MHz SPI with readback or daisy chain Low glitch: 0.5 nV-sec Low power: 3.3 mW at 3 V 2.7 V to 5.5 V power supply -40C to +105C temperature range VLOGIC GND VREF AD5689R/AD5687R 2.5V REFERENCE SCLK SYNC SDIN INTERFACE LOGIC INPUT REGISTER DAC REGISTER STRING DAC A VOUT A BUFFER INPUT REGISTER DAC REGISTER STRING DAC B VOUT B BUFFER SDO LDAC RESET POWER-ON RESET GAIN = x1/x2 RSTSEL GAIN POWERDOWN LOGIC 11256-001 Data Sheet Dual, 16-/12-Bit nanoDAC+ with 2 ppm/C Reference, SPI Interface AD5689R/AD5687R Figure 1. APPLICATIONS Optical transceivers Base station power amplifiers Process control (PLC I/O cards) Industrial automation Data acquisition systems GENERAL DESCRIPTION The AD5689R/AD5687R members of the nanoDAC+TM family are low power, dual, 16-/12-bit buffered voltage output digital-to-analog converters (DACs). The devices include a 2.5 V, 2 ppm/C internal reference (enabled by default) and a gain select pin giving a full-scale output of 2.5 V (gain = 1) or 5 V (gain = 2). The devices operate from a single 2.7 V to 5.5 V supply, are guaranteed monotonic by design, and exhibit less than 0.1% FSR gain error and 1.5 mV offset error performance. Both devices are available in a 3 mm x 3 mm LFCSP and a TSSOP package. The AD5689R/AD5687R also incorporate a power-on reset circuit and a RSTSEL pin that ensure that the DAC outputs power up to zero scale or midscale and remain there until a valid write takes place. Each part contains a per channel power-down feature that reduces the current consumption of the device to 4 A at 3 V while in power-down mode. The AD5689R/AD5687R use a versatile serial peripheral interface (SPI) that operates at clock rates up to 50 MHz. and both devices contain a VLOGIC pin that is intended for 1.8 V/3 V/5 V logic. Rev. B Table 1. Dual nanoDAC+ Devices Interface SPI I2C Reference Internal External Internal 16-Bit AD5689R AD5689 12-Bit AD5687R AD5687 AD5697R PRODUCT HIGHLIGHTS 1. 2. 3. High Relative Accuracy (INL). AD5689R (16-bit): 2 LSB maximum AD5687R (12-bit): 1 LSB maximum Low Drift 2.5 V On-Chip Reference. 2 ppm/C typical temperature coefficient 5 ppm/C maximum temperature coefficient Two Package Options. 3 mm x 3 mm, 16-lead LFCSP 16-lead TSSOP Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2013-2017 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD5689R/AD5687R Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Write and Update Commands .................................................. 21 Applications ....................................................................................... 1 Daisy-Chain Operation ............................................................. 21 Functional Block Diagram .............................................................. 1 Readback Operation .................................................................. 22 General Description ......................................................................... 1 Power-Down Operation ............................................................ 22 Product Highlights ........................................................................... 1 Load DAC (Hardware LDAC Pin) ........................................... 23 Revision History ............................................................................... 2 LDAC Mask Register ................................................................. 23 Specifications..................................................................................... 3 Hardware Reset (RESET) .......................................................... 24 AC Characteristics........................................................................ 5 Reset Select Pin (RSTSEL) ........................................................ 24 Timing Characteristics ................................................................ 6 Internal Reference Setup ........................................................... 24 Daisy-Chain and Readback Timing Characteristics ............... 7 Solder Heat Reflow..................................................................... 24 Absolute Maximum Ratings............................................................ 9 Long-Term Temperature Drift ................................................. 24 ESD Caution .................................................................................. 9 Thermal Hysteresis .................................................................... 25 Pin Configurations and Function Descriptions ......................... 10 Applications Information .............................................................. 26 Typical Performance Characteristics ........................................... 11 Microprocessor Interfacing ....................................................... 26 Terminology .................................................................................... 17 AD5689R/AD5687R to ADSP-BF531 Interface ...................... 26 Theory of Operation ...................................................................... 19 AD5689R/AD5687R to SPORT Interface ................................ 26 Digital-to-Analog Converters ................................................... 19 Layout Guidelines....................................................................... 26 Transfer Function ....................................................................... 19 Galvanically Isolated Interface ................................................. 26 DAC Architecture ....................................................................... 19 Outline Dimensions ....................................................................... 27 Serial Interface ............................................................................ 20 Ordering Guide .......................................................................... 28 Standalone Operation ................................................................ 21 REVISION HISTORY 3/2017--Rev. A to Rev. B Changes to Features and Table 1 .................................................... 1 Changed 1.8 V VLOGIC 5.5 V to 1.62 V VLOGIC 5.5 V......... 3 Change to VLOGIC Parameter, Table 2 .............................................. 4 Changed 1.8 V VLOGIC 5.5 V to 1.8 V - 10% VLOGIC 5 V + 10% ..................................................................................................... 5 Changed 1.8 V VLOGIC 5.5 V to 1.62 V VLOGIC 5.5 V......... 6 Changes to Table 4 and Figure 2 ..................................................... 6 Changed 1.8 V VLOGIC 5.5 V to 1.62 V VLOGIC 5.5 V......... 7 Changes to Table 5 and Figure 4 ..................................................... 7 Changes to Figure 5 .......................................................................... 8 Changes to Table 6 ............................................................................ 9 Changes to Table 7 .......................................................................... 10 Changes to Figure 12 ...................................................................... 11 Changes to Figure 19 ...................................................................... 12 Changes to Figure 20 to Figure 23 and Figure 25 ....................... 13 Changes to Figure 26, Figure 27, Figure 29, and Figure 30....... 14 Changes to Figure 33, Figure 36, and Figure 37 ......................... 15 Change to Table 9 ........................................................................... 20 Change to Readback Operation Section ..................................... 22 Change to Table 14 ......................................................................... 23 Changes to Hardware Reset Section and Reset Select Pin (RSTSEL) Section ........................................................................... 24 Added Long-Term Temperature Drift Section and Figure 49; Renumbered Sequentially ............................................................. 24 5/2014--Rev. 0 to Rev. A Deleted Long-Term Stability/Drift Parameter, Table 1 ................4 Deleted Figure 11; Renumbered Sequentially ............................ 11 Deleted Long-Term Temperature Drift Section ......................... 24 2/2013--Revision 0: Initial Version Rev. B | Page 2 of 28 Data Sheet AD5689R/AD5687R SPECIFICATIONS VDD = 2.7 V to 5.5 V; 1.62 V VLOGIC 5.5 V; all specifications TMIN to TMAX, unless otherwise noted. RL = 2 k; CL = 200 pF. Table 2. Parameter STATIC PERFORMANCE2 AD5689R Resolution Relative Accuracy Differential Nonlinearity AD5687R Resolution Relative Accuracy Differential Nonlinearity Zero-Code Error Offset Error Full-Scale Error Gain Error Total Unadjusted Error Min 16 Resistive Load4 Load Regulation Short-Circuit Current5 Load Impedance at Rails6 Power-Up Time 8 8 1 12 1 1 0.4 +0.1 +0.01 0.02 0.01 2 1 0.12 4 4 0.2 0.2 0.25 0.25 0.4 +0.1 +0.01 0.02 0.01 Unit Bits LSB Test Conditions/Comments 2 3 1 LSB Gain = 2 Gain = 1 Guaranteed monotonic by design 1 1 Bits LSB LSB Guaranteed monotonic by design 12 0.12 1 1 1 1 mV mV % of FSR % of FSR % of FSR % of FSR V/C ppm 0.15 0.15 mV/V DAC code = midscale; VDD = 5 V 10% 2 2 V 3 2 3 2 V/mA V Due to single channel, full-scale output change Due to load current change Due to powering down (per channel) 0 0 Capacitive Load Stability Min B Grade1 Typ Max 16 2 2 Offset Error Drift3 Gain Temperature Coefficient3 DC Power Supply Rejection Ratio3 DC Crosstalk3 OUTPUT CHARACTERISTICS3 Output Voltage Range A Grade1 Typ Max VREF 2 x VREF 0 0 1.5 1.5 0.1 0.1 0.1 0.2 80 80 V V nF nF k V/mA 80 80 V/mA 40 25 2.5 40 25 2.5 mA s 2 10 1 VREF 2 x VREF 2 10 1 Rev. B | Page 3 of 28 All 0s loaded to DAC register All 1s loaded to DAC register External reference; gain = 2; TSSOP Internal reference; gain = 1; TSSOP Of FSR/C Gain = 1 Gain = 2, see Figure 31 RL = RL = 1 k 5 V 10%, DAC code = midscale; -30 mA IOUT 30 mA 3 V 10%, DAC code = midscale; -20 mA IOUT 20 mA See Figure 31 Coming out of power-down mode; VDD = 5 V AD5689R/AD5687R Parameter REFERENCE OUTPUT Output Voltage7 Reference Temperature Coefficient8, 9 Output Impedance3 Output Voltage Noise3 Output Voltage Noise Density3 Load Regulation Sourcing3 Load Regulation Sinking3 Output Current Load Capability3 Line Regulation3 Thermal Hysteresis3 LOGIC INPUTS3 Input Current Input Low Voltage (VINL) Input High Voltage (VINH) Pin Capacitance LOGIC OUTPUTS (SDO)3 Output Low Voltage (VOL) Output High Voltage (VOH) Floating State Output Capacitance POWER REQUIREMENTS VLOGIC ILOGIC VDD VDD IDD Min Data Sheet A Grade1 Typ Max 2.4975 5 2.5025 20 Min B Grade1 Typ Max 2.4975 2 2.5025 5 Unit Test Conditions/Comments V ppm/C At ambient See the Long-Term Temperature Driftsection 0.04 12 240 0.04 12 240 V p-p nV/Hz 20 40 5 20 40 5 V/mA V/mA mA 0.1 Hz to 10 Hz At ambient; f = 10 kHz, CL = 10 nF At ambient At ambient VDD 3 V 100 125 25 100 125 25 V/V ppm ppm At ambient First cycle Additional cycles 2 0.3 x VLOGIC A V V pF Per pin 0.4 V V pF ISINK = 200 A ISOURCE = 200 A 5.5 3 5.5 5.5 V A V V 2 0.3 x VLOGIC 0.7 x VLOGIC 0.7 x VLOGIC 2 2 0.4 VLOGIC - 0.4 VLOGIC - 0.4 4 1.62 4 5.5 3 5.5 5.5 2.7 VREF + 1.5 1.62 2.7 VREF + 1.5 Normal Mode10 0.59 1.1 0.7 1.3 0.59 1.1 0.7 1.3 mA mA All Power-Down Modes11 1 4 1 4 A Gain = 1 Gain = 2 VIH = VDD, VIL = GND, VDD = 2.7 V to 5.5 V Internal reference off Internal reference on, at full scale -40C to +85C 6 A -40C to +105C 6 1 Temperature range for A and B grades: -40C to +105C. DC specifications tested with the outputs unloaded, unless otherwise noted. Upper dead band = 10 mV; it exists only when VREF = VDD with gain = 1 or when VREF/2 = VDD with gain = 2. Linearity is calculated using a reduced code range of 256 to 65,280 (AD5689R) and 12 to 4080 (AD5687R). 3 Guaranteed by design and characterization; not production tested. 4 Channel A can have an output current of up to 30 mA. Similarly, Channel B can have an output current of up to 30 mA, up to a junction temperature of 110C. 5 VDD = 5 V. The devices include current limiting that is intended to protect them during temporary overload conditions. Junction temperature may be exceeded during current limit, but operation above the specified maximum operation junction temperature can impair device reliability. 6 When drawing a load current at either rail, the output voltage headroom, with respect to that rail, is limited by the 25 typical channel resistance of the output devices. For example, when sinking 1 mA, the minimum output voltage = 25 x 1 mA = 25 mV (see Figure 31). 7 Initial accuracy presolder reflow is 750 V; output voltage includes the effects of preconditioning drift. See the Internal Reference Setup section. 8 Reference is trimmed and tested at two temperatures and is characterized from -40C to +105C. 9 Reference temperature coefficient is calculated as per the box method. See the Terminology section for more information. 10 Interface inactive. Both DACs active. DAC outputs unloaded. 11 Both DACs powered down. 2 Rev. B | Page 4 of 28 Data Sheet AD5689R/AD5687R AC CHARACTERISTICS VDD = 2.7 V to 5.5 V; RL = 2 k to GND; CL = 200 pF to GND; 1.8 V - 10% VLOGIC 5 V + 10%; all specifications TMIN to TMAX, unless otherwise noted. Guaranteed by design and characterization; not production tested. Table 3. Parameter1 Output Voltage Settling Time AD5689R AD5687R Slew Rate Digital-to-Analog Glitch Impulse Digital Feedthrough Digital Crosstalk Analog Crosstalk DAC-to-DAC Crosstalk Total Harmonic Distortion (THD)3 Output Noise Spectral Density (NSD) Output Noise Signal-to-Noise Ratio (SNR) Spurious Free Dynamic Range (SFDR) Signal-to-Noise-and-Distortion Ratio (SINAD) Min Typ Max Unit Test Conditions/Comments2 5 5 0.8 0.5 0.13 0.1 0.2 0.3 -80 300 6 90 83 80 8 7 s s V/s nV-sec nV-sec nV-sec nV-sec nV-sec dB nV/Hz V p-p dB dB dB 1/4 to 3/4 scale settling to 2 LSB 1/4 to 3/4 scale settling to 2 LSB 1 See the Terminology section. Temperature range is -40C to +105C, typical at 25C. 3 Digitally generated sine wave at 1 kHz. 2 Rev. B | Page 5 of 28 1 LSB change around major carry At ambient, BW = 20 kHz, VDD = 5 V, fOUT = 1 kHz DAC code = midscale, 10 kHz; gain = 2 0.1 Hz to 10 Hz At ambient, BW = 20 kHz, VDD = 5 V, fOUT = 1 kHz At ambient, BW = 20 kHz, VDD = 5 V, fOUT = 1 kHz At ambient, BW = 20 kHz, VDD = 5 V, fOUT = 1 kHz AD5689R/AD5687R Data Sheet TIMING CHARACTERISTICS All input signals are specified with tR = tF = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. See Figure 2. VDD = 2.7 V to 5.5 V, 1.62 V VLOGIC 5.5 V; VREF = 2.5 V. All specifications TMIN to TMAX, unless otherwise noted. Table 4. Parameter1 SCLK Cycle Time SCLK High Time SCLK Low Time SYNC to SCLK Falling Edge Setup Time Data Setup Time Data Hold Time SCLK Falling Edge to SYNC Rising Edge Minimum SYNC High Time SYNC Rising Edge to SYNC Rising Edge (DAC Register Updates) SYNC Falling Edge to SCLK Fall Ignore LDAC Pulse Width Low SYNC Rising Edge to LDAC Rising Edge SYNC Rising Edge to LDAC Falling Edge LDAC Falling Edge to SYNC Rising Edge Minimum Pulse Width Low Pulse Activation Time Power-Up Time2 E E E E E E E E E E E E 1.62 V VLOGIC < 2.7 V Min Max 20 10 10 15 5 5 10 20 870 16 15 20 30 840 30 30 4.5 Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 t16 E 2.7 V VLOGIC 5.5 V Min Max 20 10 10 10 5 5 10 20 830 10 15 20 30 800 30 30 4.5 1 Guaranteed by design and characterization; not production tested. Time to exit power-down to normal mode of AD5689R/AD5687R operation, SYNC rising edge to 90% of DAC midscale value, with output unloaded. 2 E t10 t1 SCLK t8 t3 t4 t2 t7 t14 SYNC t5 SDIN t6 DB23 t9 DB0 t11 t13 1 t12 2 t15 t16 11256-002 VOUT 1 2 Figure 2. Serial Write Operation Rev. B | Page 6 of 28 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns s Data Sheet AD5689R/AD5687R DAISY-CHAIN AND READBACK TIMING CHARACTERISTICS All input signals are specified with tR = tF = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. See Figure 4 and Figure 5. VDD = 2.7 V to 5.5 V, 1.62 V VLOGIC 5.5 V; VREF = 2.5 V. All specifications TMIN to TMAX, unless otherwise noted. VDD = 2.7 V to 5.5 V. Table 5. Parameter1 SCLK Cycle Time SCLK High Time SCLK Low Time SYNC to SCLK Falling Edge Data Setup Time Data Hold Time SCLK Falling Edge to SYNC Rising Edge Minimum SYNC High Time SDO Data Valid from SCLK Rising Edge SYNC Rising Edge to SCLK Rising Edge SYNC Rising Edge to SDO Disable Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 E E E E E 1 Min 66 33 33 33 5 5 15 60 1.62 V VLOGIC < 2.7 V Max Min 40 20 20 20 5 5 10 30 2.7 V VLOGIC 5.5 V Max 45 Unit ns ns ns ns ns ns ns ns ns ns ns 30 15 60 10 60 Guaranteed by design and characterization; not production tested. Circuit and Timing Diagrams 200A VOH (MIN) CL 20pF 200A 11256-004 TO OUTPUT PIN IOL IOH Figure 3. Load Circuit for Digital Output (SDO) Timing Specifications t1 24 t2 t8 t4 t7 t3 t10 t6 DB23 DB0 INPUT WORD FOR DAC N DB23 DB0 t9 UNDEFINED INPUT WORD FOR DAC N + 1 INPUT WORD FOR DAC N Figure 4. Daisy-Chain Timing Diagram Rev. B | Page 7 of 28 11256-004 t5 48 AD5689R/AD5687R Data Sheet t1 SCLK 24 1 t8 t4 t3 24 1 t7 t2 t8 t10 SYNC t6 t5 DB23 DB0 DB23 INPUT WORD SPECIFIES REGISTER TO BE READ DB0 NOP CONDITION t9 DB23 SDO t11 DB0 HI-Z SELECTED REGISTER DATA CLOCKED OUT Figure 5. Readback Timing Diagram Rev. B | Page 8 of 28 11256-005 SDIN Data Sheet AD5689R/AD5687R ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 6. Parameter VDD to GND VLOGIC to GND VOUT to GND VREF to GND Digital Input Voltage to GND Operating Temperature Range Storage Temperature Range Junction Temperature 16-Lead TSSOP, JA Thermal Impedance, 0 Airflow (4-Layer Board) 16-Lead LFCSP, JA Thermal Impedance, 0 Airflow (4-Layer Board) Reflow Soldering Peak Temperature, Pb Free (J-STD-020) Rating -0.3 V to +7 V -0.3 V to +7 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -0.3 V to VLOGIC + 0.3 V -40C to +105C -65C to +150C 125C 112.6C/W Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION 70C/W 260C Rev. B | Page 9 of 28 AD5689R/AD5687R Data Sheet 13 RESET 14 RSTSEL 16 NC 15 VREF PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS VOUTA 1 VDD 3 12 SDIN AD5689R/ AD5687R RSTSEL 15 RESET 14 SDIN 13 SYNC 12 SCLK NC 6 11 VLOGIC VOUTB 7 10 GAIN SDO 8 9 LDAC VREF 1 10 SCLK NC 2 VOUTA 3 9 VLOGIC NC 4 16 11 SYNC GAIN 8 LDAC 7 SDO 6 VOUTB 5 GND 4 VDD 5 NOTES 1. THE EXPOSED PAD MUST BE TIED TO GND. 2. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. 11256-007 TOP VIEW (Not to Scale) AD5689R/ AD5687R TOP VIEW (Not to Scale) NOTES 1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. 11256-008 GND 2 Figure 7. 16-Lead TSSOP Pin Configuration Figure 6. 16-Lead LFCSP Pin Configuration Table 7. Pin Function Descriptions Pin No. LFCSP TSSOP 1 3 2 4 3 5 Mnemonic VOUTA GND VDD 4 5 6 6 7 8 NC VOUTB SDO 7 9 LDAC 8 10 GAIN 9 10 11 12 VLOGIC SCLK 11 13 SYNC 12 14 SDIN 13 15 RESET 14 16 RSTSEL 15 1 VREF 16 17 2 N/A NC EPAD Description Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation. Ground Reference Point for All Circuitry on the AD5689R/AD5687R. Power Supply Input. The AD5689R/AD5687R can be operated from 2.7 V to 5.5 V. Decouple the supply with a 10 F capacitor in parallel with a 0.1 F capacitor to GND. No Connect. Do not connect to this pin. Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation. Serial Data Output. SDO can be used to daisy-chain a number of AD5689R/AD5687R devices together, or it can be used for readback. The serial data is transferred on the rising edge of SCLK and is valid on the falling edge of the clock. LDAC can be operated in two modes: asynchronous and synchronous. Pulsing this pin low allows either or both DAC registers to be updated if the input registers have new data; both DAC outputs can be updated simultaneously. This pin can also be tied permanently low. Gain Select. When this pin is tied to GND, both DACs output a span from 0 V to VREF. If this pin is tied to VLOGIC, both DACs output a span of 0 V to 2 x VREF. Digital Power Supply. The voltage on this pin ranges from 1.62 V to 5.5 V. Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be transferred at rates of up to 50 MHz. Active Low Control Input. This is the frame synchronization signal for the input data. When SYNC goes low, data is transferred in on the falling edges of the next 24 clocks. Serial Data Input. This device has a 24-bit input shift register. Data is clocked into the register on the falling edge of the serial clock input. Asynchronous Reset Input. The RESET input is falling edge sensitive. When RESET is low, all LDAC pulses are ignored. When RESET is activated, the input register and the DAC register are updated with zero scale or midscale, depending on the state of the RSTSEL pin. If this pin is forced low at power-up, the power-on reset (POR) circuit does not initialize the device correctly until this pin is released. Power-On Reset Select. Tying this pin to GND powers up both DACs to zero scale. Tying this pin to VLOGIC powers up both DACs to midscale. Reference Voltage. The AD5689R/AD5687R have a common reference pin. When using the internal reference, this is the reference output pin. When using an external reference, this is the reference input pin. The default for this pin is as a reference output. No Connect. Do not connect to this pin. Exposed Pad. The exposed pad must be tied to GND. Rev. B | Page 10 of 28 Data Sheet AD5689R/AD5687R TYPICAL PERFORMANCE CHARACTERISTICS 2.5015 2.5010 DEVICE 1 DEVICE 2 DEVICE 3 DEVICE 4 DEVICE 5 1600 VDD = 5V 1400 1200 1000 NSD (nV/ Hz) VREF (V) 2.5005 2.5000 2.4995 800 600 2.4990 400 2.4985 200 -20 0 20 40 60 80 100 120 TEMPERATURE (C) 0 10 11256-009 2.4980 -40 2.5015 2.5010 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 11. Internal Reference Noise Spectral Density vs. Frequency Figure 8. Internal Reference Voltage vs. Temperature (Grade B) 2.5020 VDD = 5V TA = 25C 11256-013 2.5020 DEVICE 1 DEVICE 2 DEVICE 3 DEVICE 4 DEVICE 5 VDD = 5V TA = 25C T VREF (V) 2.5005 2.5000 1 2.4995 2.4990 2.4985 0 20 40 60 80 100 120 TEMPERATURE (C) CH1 2V A CH1 160mV Figure 12. Internal Reference Noise, 0.1 Hz to 10 Hz Figure 9. Internal Reference Voltage vs. Temperature (Grade A) 90 M1.0s 11256-112 VDD = 5V -20 11256-010 2.4980 -40 2.5000 VDD = 5V 80 2.4999 VDD = 5V TA = 25C 2.4998 VREF (V) 60 50 40 30 2.4997 2.4996 2.4995 20 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 TEMPERATURE DRIFT (ppm/C) 5.0 Figure 10. Reference Output Temperature Drift Histogram 2.4993 -0.005 -0.003 -0.001 0.001 0.003 ILOAD (A) Figure 13. Internal Reference Voltage vs. Load Current Rev. B | Page 11 of 28 0.005 11256-015 2.4994 10 11256-011 NUMBER OF UNITS 70 Data Sheet 10 10 8 8 6 6 4 4 2 2 INL (LSB) 0 -2 -4 0 -2 -4 -6 -6 10000 20000 30000 40000 50000 60000 CODE -10 0 625 0.6 0.6 0.4 0.4 0.2 0.2 DNL (LSB) 0.8 0 -0.2 -0.4 -0.6 VDD = 5V TA = 25C INTERNAL REFERENCE = 2.5V -0.8 50000 60000 -1.0 0 625 2500 3125 3750 4096 10 TA = 25C 8 2.5000 6 4 ERROR (LSB) 2.4998 D3 2.4996 2.4994 2 INL 0 DNL -2 -4 -6 2.4992 D2 3.0 3.5 4.0 -8 4.5 5.0 5.5 VDD (V) 11256-016 VREF (V) 1875 Figure 18. AD5687R DNL vs. Code D1 2.4990 2.5 1250 CODE Figure 15. AD5689R Differential Nonlinearity (DNL) vs. Code 2.5002 3750 4096 0 -0.6 40000 3125 -0.2 -0.4 11256-019 DNL (LSB) 1.0 0.8 CODE 2500 Figure 17. AD5687R INL vs. Code 1.0 30000 1875 CODE Figure 14. AD5689R Integral Nonlinearity (INL) vs. Code VDD = 5V -0.8 TA = 25C REFERENCE = 2.5V -1.0 0 10000 20000 1250 11256-020 0 11256-017 -10 VDD = 5V TA = 25C INTERNAL REFERENCE = 2.5V -8 11256-018 VDD = 5V TA = 25C REFERENCE = 2.5V -8 Figure 16. Internal Reference Voltage vs. Supply Voltage VDD = 5V INTERNAL REFERENCE = 2.5V -10 -40 10 60 110 TEMPERATURE (C) Figure 19. INL Error and DNL Error vs. Temperature Rev. B | Page 12 of 28 11256-124 INL (LSB) AD5689R/AD5687R Data Sheet AD5689R/AD5687R 10 VDD = 5V 1.4 INTERNAL REFERENCE = 2.5V 6 1.2 4 1.0 2 ERROR (mV) INL 0 DNL -2 -4 0.8 0.6 0.4 VDD = 5V TA = 25C -6 ZERO-CODE ERROR 0.2 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VREF (V) 8 0.08 6 0.06 4 0.04 ERROR (% of FSR) ERROR (LSB) 0.10 2 INL DNL -4 4.7 5.2 SUPPLY VOLTAGE (V) 80 100 120 0.02 GAIN ERROR 0 FULL-SCALE ERROR -0.02 -0.04 0.10 0.08 0.08 0.06 0.06 ERROR (% of FSR) 0.04 FULL-SCALE ERROR GAIN ERROR -0.02 -0.04 0.04 0.02 GAIN ERROR 0 FULL-SCALE ERROR -0.02 -0.04 -0.06 -0.08 VDD = 5V INTERNAL REFERENCE = 2.5V -0.10 -40 -20 0 20 40 -0.08 TA = 25C INTERNAL REFERENCE = 2.5V -0.10 2.7 3.2 3.7 4.2 100 120 TEMPERATURE (C) 11256-127 -0.06 80 5.2 Figure 24. Gain Error and Full-Scale Error vs. Supply 0.10 60 4.7 SUPPLY VOLTAGE (V) Figure 21. INL Error and DNL Error vs. Supply Voltage ERROR (% of FSR) 60 VDD = 5V -0.08 T = 25C A INTERNAL REFERENCE = 2.5V -0.10 2.7 3.2 3.7 4.2 11256-126 -8 TA = 25C INTERNAL REFERENCE = 2.5V -10 2.7 3.2 3.7 4.2 0 40 -0.06 -6 0.02 20 Figure 23. Zero-Code Error and Offset Error vs. Temperature 10 -2 0 TEMPERATURE (C) Figure 20. INL Error and DNL Error vs. VREF 0 -20 11256-026 0 0 -40 11256-125 -10 11256-128 OFFSET ERROR -8 Figure 22. Gain Error and Full-Scale Error vs. Temperature 4.7 5.2 SUPPLY VOLTAGE (V) Figure 25. Zero-Code Error and Offset Error vs. Supply Voltage Rev. B | Page 13 of 28 11256-129 ERROR (LSB) 8 AD5689R/AD5687R Data Sheet VDD = 5V 0.09 INTERNAL REFERENCE = 2.5V 0.08 20 0.07 HITS 0.06 0.05 0.04 0.03 5 0.02 0 -20 0 20 40 60 80 100 120 TEMPERATURE (C) 540 560 580 600 620 640 IDD (A) 11256-135 0.01 Figure 29. IDD Histogram with External Reference, VDD = 5 V Figure 26. Total Unadjusted Error (TUE) vs. Temperature 0.10 VDD = 5V 30 T = 25C A INTERNAL REFERENCE = 2.5V 25 0.08 0.06 0.04 20 HITS 0.02 0 15 -0.02 10 -0.04 -0.06 5 -0.10 2.7 0 3.2 3.7 4.2 4.7 5.2 SUPPLY VOLTAGE (V) 1000 1020 1040 1060 1080 1100 1120 1140 IDD (A) Figure 27. TUE vs. Supply, Gain = 1 11256-136 TA = 25C INTERNAL REFERENCE = 2.5V Figure 30. IDD Histogram with Internal Reference, VREF = 2.5 V, Gain = 2 0 1.0 -0.01 0.8 -0.02 0.6 -0.03 0.4 -0.04 0.2 VOUT (V) SINKING 2.7V -0.05 -0.06 -0.2 -0.07 -0.4 -0.08 -0.6 SOURCING 5V SOURCING 2.7V -0.8 -1.0 40000 CODE 50000 60000 65535 11256-030 VDD = 5V -0.09 T = 25C A INTERNAL REFERENCE = 2.5V -0.10 0 10000 20000 30000 SINKING 5V 0 0 5 10 15 20 25 LOAD CURRENT (mA) Figure 31. Headroom/Footroom vs. Load Current Figure 28. TUE vs. Code Rev. B | Page 14 of 28 30 11256-033 -0.08 11256-132 TOTAL UNADJUSTED ERROR (% of FSR) 15 10 0 -40 TOTAL UNADJUSTED ERROR (% of FSR) VDD = 5V TA = 25C EXTERNAL REFERENCE = 2.5V 25 11256-131 TOTAL UNADJUSTED ERROR (% of FSR) 0.10 Data Sheet AD5689R/AD5687R 2.5008 7 VDD = 5V 6 TA = 25C GAIN = 2 REFERENCE = 2.5V 5 4 FULL SCALE 2.5003 VOUT (V) VOUT (V) THREE-QUARTER SCALE 3 MIDSCALE 2 ONE-QUARTER SCALE 2.4998 1 CHANNEL B TA = 25C VDD = 5.25V INTERNAL REFERENCE POSITIVE MAJOR CODE TRANSITION ENERGY = 0.227206nV-sec 2.4993 -1 -0.04 -0.02 0 0.02 0.04 2.4988 11256-034 -2 -0.06 0.06 LOAD CURRENT (A) 0 10 12 T 0xFFFF 0xC000 2 0x8000 1 1 0x4000 -1 -40 -20 0 20 40 60 IOUT (mA) 11256-139 -2 -60 VDD = 5V TA = 25C EXTERNAL REFERENCE = 2.5V CH1 2V Figure 33. Source and Sink Capability at 3 V, Gain = 1 1.0 A CH1 802mV Figure 36. 0.1 Hz to 10 Hz Output Noise Plot, External Reference 1.4 1.2 M1.0s 11256-146 0x0000 0 T FULL SCALE ZERO CODE 0.8 0.6 1 EXTERNAL REFERENCE, FULL SCALE 0.4 0.2 0 -40 10 60 TEMPERATURE (C) Figure 34. Supply Current vs. Temperature 110 VDD = 5V TA = 25C INTERNAL REFERENCE = 2.5V 11256-036 SUPPLY CURRENT (mA) 8 CH1 2V M1.0s A CH1 802mV 11256-147 VOUT (V) 3 6 Figure 35. Digital-to-Analog Glitch Impulse VDD = 3V TA = 25C GAIN = 1 EXTERNAL REFERENCE = 2.5V 4 4 TIME (s) Figure 32. Source and Sink Capability at 5 V, Gain = 2 5 2 11256-037 ZERO SCALE 0 Figure 37. 0.1 Hz to 10 Hz Output Noise Plot, 2.5 V Internal Reference Rev. B | Page 15 of 28 AD5689R/AD5687R Data Sheet 0 1600 VDD = 5V TA = 25C 1400 INTERNAL REFERENCE = 2.5V FULL SCALE MIDSCALE ZERO SCALE -10 BANDWIDTH (dB) NSD (nV/ Hz) 1200 1000 800 600 -20 -30 -40 400 100 1k 10k 100k 1M FREQUENCY (Hz) -60 10k 11256-040 0 10 -20 -60 -80 -100 -120 -140 -160 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 20000 FREQUENCY (Hz) 11256-041 THD (dBV) -40 -180 1M 10M Figure 40. Multiplying Bandwidth, External Reference = 2.5 V, 0.1 V p-p, 10 kHz to 10 MHz VDD = 5V TA = 25C REFERENCE = 2.5V 0 100k FREQUENCY (Hz) Figure 38. Noise Spectral Density (NSD) 20 VDD = 5V TA = 25C REFERENCE = 2.5V, 0.1V p-p 11256-042 -50 200 Figure 39. Total Harmonic Distortion at 1 kHz Rev. B | Page 16 of 28 Data Sheet AD5689R/AD5687R TERMINOLOGY Relative Accuracy or Integral Nonlinearity (INL) For the DAC, relative accuracy or integral nonlinearity is a measurement of the maximum deviation, in LSBs, from a straight line passing through the endpoints of the DAC transfer function. Typical INL vs. code plots are shown in Figure 14 and Figure 17. Output Voltage Settling Time Output voltage settling time is the amount of time it takes for the output of a DAC to settle to a specified level for a 1/4 to 3/4 full-scale input change and is measured from the rising edge of SYNC. Differential Nonlinearity (DNL) Differential nonlinearity is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of 1 LSB maximum ensures monotonicity. This DAC is guaranteed monotonic by design. Typical DNL vs. code plots are shown in Figure 15 and Figure 18. Digital-to-Analog Glitch Impulse Digital-to-analog glitch impulse is the impulse injected into the analog output when the input code in the DAC register changes state. It is normally specified as the area of the glitch in nV-sec, and is measured when the digital input code is changed by 1 LSB at the major carry transition (0x7FFF to 0x8000) (see Figure 35). Zero-Code Error Zero-code error is a measurement of the output error when zero code (0x0000) is loaded to the DAC register. Ideally, the output should be 0 V. The zero-code error is always positive in the device because the output of the DAC cannot go below 0 V due to a combination of the offset errors in the DAC and the output amplifier. Zero-code error is expressed in mV. A plot of zero-code error vs. temperature is shown in Figure 23. Full-Scale Error Full-scale error is a measurement of the output error when fullscale code (0xFFFF) is loaded to the DAC register. Ideally, the output should be VDD - 1 LSB. Full-scale error is expressed in percent of full-scale range (% of FSR). A plot of full-scale error vs. temperature is shown in Figure 22. Gain Error Gain error is a measure of the span error of the DAC. It is the deviation in slope of the DAC transfer characteristic from the ideal and is expressed as % of FSR. Offset Error Drift Offset error drift is a measurement of the change in offset error with a change in temperature. It is expressed in V/C. Gain Temperature Coefficient Gain temperature coefficient is a measurement of the change in gain error with changes in temperature. It is expressed in ppm of FSR/C. Offset Error Offset error is a measure of the difference between VOUT (actual) and VOUT (ideal) expressed in mV in the linear region of the transfer function. Offset error is measured on the device with Code 512 loaded in the DAC register. It can be negative or positive. DC Power Supply Rejection Ratio (PSRR) PSRR indicates how the output of the DAC is affected by changes in the supply voltage. It is the ratio of the change in VOUT to a change in VDD for full-scale output of the DAC. It is measured in mV/V. VREF is held at 2 V, and VDD is varied by 10%. Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of the DAC from the digital inputs of the DAC, but it is measured when the DAC output is not updated. It is specified in nV-sec and measured with a full-scale code change on the data bus, that is, from all 0s to all 1s and vice versa. Reference Feedthrough Reference feedthrough is the ratio of the amplitude of the signal at the DAC output to the reference input when the DAC output is not being updated. It is expressed in dB. Noise Spectral Density (NSD) NSD is a measurement of the internally generated random noise. Random noise is characterized as a spectral density (nV/Hz). It is measured, in nV/Hz, by loading the DAC to midscale and measuring noise at the output. A noise spectral density plot is shown in Figure 38. DC Crosstalk DC crosstalk is the dc change in the output level of one DAC in response to a change in the output of another DAC. It is measured with a full-scale output change on one DAC (or soft power-down and power-up) while monitoring another DAC kept at midscale. It is expressed in V. DC crosstalk due to load current change is a measure of the impact that a change in load current on one DAC has to another DAC kept at midscale. It is expressed in V/mA. Digital Crosstalk Digital crosstalk is the glitch impulse transferred to the output of one DAC at midscale in response to a full-scale code change (all 0s to all 1s and vice versa) in the input register of another DAC. It is measured in standalone mode and expressed in nV-sec. Analog Crosstalk Analog crosstalk is the glitch impulse transferred to the output of one DAC due to a change in the output of another DAC. It is measured by loading one of the input registers with a full-scale code change (all 0s to all 1s and vice versa). Then execute a software LDAC and monitor the output of the DAC whose digital code was not changed. The area of the glitch is expressed in nV-sec. Rev. B | Page 17 of 28 AD5689R/AD5687R Data Sheet DAC-to-DAC Crosstalk DAC-to-DAC crosstalk is the glitch impulse transferred to the output of one DAC due to a digital code change and subsequent analog output change of another DAC. It is measured by loading the attack channel with a full-scale code change (all 0s to all 1s and vice versa), using the write to and update commands while monitoring the output of the victim channel that is at midscale. The energy of the glitch is expressed in nV-sec. Multiplying Bandwidth The amplifiers within the DAC have a finite bandwidth. The multiplying bandwidth is a measure of this. A sine wave on the reference (with full-scale code loaded to the DAC) appears on the output. The multiplying bandwidth is the frequency at which the output amplitude falls to 3 dB below the input. Total Harmonic Distortion (THD) THD is the difference between an ideal sine wave and its attenuated version using the DAC. The sine wave is used as the reference for the DAC, and the THD is a measurement of the harmonics present on the DAC output. It is measured in dB. Voltage Reference Temperature Coefficient Voltage reference TC is a measure of the change in the reference output voltage with a change in temperature. The reference TC is calculated using the box method, which defines the TC as the maximum change in the reference output over a given temperature range expressed in ppm/C, as follows; VREFmax VREFmin 6 TC 10 VREFnom TempRange where: VREFmax is the maximum reference output measured over the total temperature range. VREFmin is the minimum reference output measured over the total temperature range. VREFnom is the nominal reference output voltage, 2.5 V. TempRange is the specified temperature range of -40C to +105C. Rev. B | Page 18 of 28 Data Sheet AD5689R/AD5687R THEORY OF OPERATION DIGITAL-TO-ANALOG CONVERTERS The AD5689R/AD5687R are dual 16-/12-bit, serial input, voltage output DACs with an internal reference. The parts operate from supply voltages of 2.7 V to 5.5 V. Data is written to the AD5689R/AD5687R in a 24-bit word format via a 3-wire serial interface. The devices incorporate a power-on reset circuit to ensure that the DAC output powers up to a known output state. The AD5689R/AD5687R also have a software power-down mode that reduces the typical current consumption to 4 A. The voltage is tapped off by closing one of the switches connecting the string to the amplifier. Because it is a string of resistors, it is guaranteed monotonic. VREF R R R TO OUTPUT AMPLIFIER TRANSFER FUNCTION The internal reference is on by default. To use an external reference, only a nonreference option is available. Because the input coding to the DAC is straight binary, the ideal output voltage when using an external reference is given by R D VOUT VREF Gain N 2 11256-044 R where: Gain is the output amplifier gain and is set to 1 by default. It can be set to x1 or x2 using the gain select pin. When the GAIN pin is tied to GND, both DACs output a span from 0 V to VREF. If the GAIN pin is tied to VLOGIC, both DACs output a span of 0 V to 2 x VREF. D is the decimal equivalent of the binary code that is loaded to the DAC register as follows: 0 to 4,095 for the 12-bit device and 0 to 65,535 for the 16-bit device. N is the DAC resolution. DAC ARCHITECTURE The DAC architecture consists of a string DAC followed by an output amplifier. Figure 41 shows a block diagram of the DAC architecture. VREF 2.5V REF REF (+) DAC REGISTER RESISTOR STRING REF (-) GND GAIN (GAIN = 1 OR 2) Internal Reference The AD5689R/AD5687R on-chip reference is on at power-up but can be disabled via a write to a control register. See the Internal Reference Setup section for details. The AD5689R/AD5687R have a 2.5 V, 2 ppm/C reference, giving a full-scale output of 2.5 V or 5 V, depending on the state of the GAIN pin. The internal reference associated with the device is available at the VREF pin. This buffered reference is capable of driving external loads of up to 10 mA. Output Amplifiers The output buffer amplifier can generate rail-to-rail voltages on its output, which gives an output range of 0 V to VDD. The actual range depends on the value of VREF, the GAIN pin, the offset error, and the gain error. The GAIN pin selects the gain of the output, as follows: VOUTX 11256-043 INPUT REGISTER Figure 42. Resistor String Structure Figure 41. Single DAC Channel Architecture Block Diagram The resistor string structure is shown in Figure 42. It is a string of resistors, each of Value R. The code loaded to the DAC register determines the node on the string where the voltage is to be tapped off and fed into the output amplifier. If the GAIN pin is tied to GND, both DAC outputs have a gain of 1, and the output range is 0 V to VREF. If the GAIN pin is tied to VLOGIC, both DAC outputs have a gain of 2, and the output range is 0 V to 2 x VREF. These amplifiers are capable of driving a load of 1 k in parallel with 2 nF to GND. The slew rate is 0.8 V/s with a 1/4 to 3/4 scale settling time of 5 s. Rev. B | Page 19 of 28 AD5689R/AD5687R Data Sheet The data-word comprises 16-bit or 12-bit input code, followed by zero don't care bits (for the AD5689R) or four don't care bits (for the AD5687R), as shown in Figure 43 and Figure 44, respectively). These data bits are transferred to the input shift register on the 24 falling edges of SCLK and updated on the rising edge of SYNC. SERIAL INTERFACE The AD5689R/AD5687R have a 3-wire serial interface (SYNC, SCLK, and SDIN) that is compatible with SPI, QSPITM, and MICROWIRE(R) interface standards as well as most DSPs. See Figure 2 for a timing diagram of a typical write sequence. The AD5689R/AD5687R contain an SDO pin that allows the user to daisy-chain multiple devices together (see the Daisy-Chain Operation section) or read back data. Commands can be executed on individual DAC channels or on both DAC channels, depending on the address bits selected. Input Shift Register Table 8. Address Commands The input shift register of the AD5689R/AD5687R is 24 bits wide, and data is loaded MSB first (DB23). The first four bits are the command bits, C3 to C0 (see Table 9), followed by the 4-bit DAC address bits, composed of DAC B, DAC A, and two don't care bits that must be set to 0 (see Table 8). Finally, the data-word completes the input shift register. DAC B 0 1 1 Address (n) 0 0 0 0 0 0 0 0 DAC A 1 0 1 Selected DAC Channel DAC A DAC B DAC A and DAC B Table 9. Command Definitions C0 0 1 0 1 0 1 0 1 0 1 0 ... 1 Description No operation Write to Input Register n (dependent on LDAC) Update DAC Register n with contents of Input Register n Write to and update DAC Channel n Power down/power up DAC Hardware LDAC mask register Software reset (power-on reset) Internal reference setup register Set up DCEN register (daisy-chain enable) Set up readback register (readback enable) Reserved Reserved No operation in daisy-chain mode DB23 (MSB) C3 C2 DB0 (LSB) C1 C0 DAC B 0 0 DAC A D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 COMMAND BITS 11256-045 DATA BITS ADDRESS BITS Figure 43. AD5689R Input Shift Register Content DB23 (MSB) C3 C2 DB0 (LSB) C1 C0 DAC B 0 0 DAC D11 D10 A D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X X DATA BITS COMM AND BITS 11256-046 C3 0 0 0 0 0 0 0 0 1 1 1 ... 1 Command C2 C1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 ... ... 1 1 ADDRESS BITS Figure 44. AD5687R Input Shift Register Content Rev. B | Page 20 of 28 Data Sheet AD5689R/AD5687R STANDALONE OPERATION AD5689R/ AD5687R 68HC11* The write sequence begins by bringing the SYNC line low. Data from the SDIN line is clocked into the 24-bit input shift register on the falling edge of SCLK. After the last of 24 data bits is clocked in, SYNC is brought high. The programmed function is then executed; that is, an LDAC-dependent change in DAC register contents and/or a change in the mode of operation occurs. If SYNC is taken high at a clock before the 24th clock, it is considered a valid frame and invalid data may be loaded to the DAC. SYNC must be brought high for a minimum of 20 ns (single channel, see t8 in Figure 2) before the next write sequence so that a falling edge of SYNC can initiate the next write sequence. Idle SYNC at the rails between write sequences for an even lower power operation of the part. The SYNC line is kept low for 24 falling edges of SCLK, and the DAC is updated on the rising edge of SYNC. MOSI SDIN SCK SCLK PC7 SYNC PC6 LDAC SDO MISO SDIN AD5689R/ AD5687R SCLK SYNC LDAC SDO SDIN When the data has been transferred into the input register of the addressed DAC, both DAC registers and outputs can be updated by taking LDAC low while the SYNC line is high. AD5689R/ AD5687R SCLK WRITE AND UPDATE COMMANDS SYNC Write to Input Register n (Dependent on LDAC) LDAC Update DAC Register n with Contents of Input Register n Command 0010 loads the DAC registers/outputs with the contents of the input registers selected and updates the DAC outputs directly. Write to and Update DAC Channel n (Independent of LDAC) Command 0011 allows the user to write to the DAC registers and update the DAC outputs directly. DAISY-CHAIN OPERATION For systems that contain several DACs, the SDO pin can be used to daisy-chain several devices together. SDO is enabled through a software executable daisy-chain enable (DCEN) command. Command 1000 is reserved for this DCEN function (see Table 9). Daisy-chain mode is enabled by setting Bit DB0 in the DCEN register. The default setting is standalone mode, where DB0 (LSB) = 0. Table 10 shows how the state of the bit corresponds to the mode of operation of the device. Table 10. Daisy-Chain Enable (DCEN) Register DB0 (LSB) 0 1 Description Standalone mode (default) DCEN mode *ADDITIONAL PINS OMITTED FOR CLARITY. 11256-047 SDO Command 0001 allows the user to write to the dedicated input register of each DAC individually. When LDAC is low, the input register is transparent (if not controlled by the LDAC mask register). Figure 45. Daisy-Chaining Multiple AD5689R/AD5687R Devices The SCLK pin is continuously applied to the input shift register when SYNC is low. If more than 24 clock pulses are applied, the data ripples out of the input shift register and appears on the SDO line. This data is clocked out on the rising edge of SCLK and is valid on the falling edge. By connecting this line to the SDIN input on the next DAC in the chain, a daisy-chain interface is constructed. Each DAC in the system requires 24 clock pulses. Therefore, the total number of clock cycles must equal 24 x N, where N is the total number of devices that are updated. If SYNC is taken high at a clock that is not a multiple of 24, it is considered a valid frame, and invalid data may be loaded to the DAC. When the serial transfer to all devices is complete, SYNC is taken high. This latches the input data in each device in the daisy chain and prevents any further data from being clocked into the input shift register. The serial clock can be continuous or a gated clock. A continuous SCLK source can be used only if SYNC can be held low for the correct number of clock cycles. In gated clock mode, a burst clock containing the exact number of clock cycles must be used, and SYNC must be taken high after the final clock to latch the data. Rev. B | Page 21 of 28 AD5689R/AD5687R Data Sheet READBACK OPERATION Table 11. Modes of Operation Readback mode is invoked through a software executable readback command. If the SDO output is disabled via the daisy-chain mode disable bit in the control register, it is automatically enabled for the duration of the read operation, after which it is disabled again. Command 1001 is reserved for the readback function in when DCEN is enable. This command, in association with selecting one of the address bits, DAC B or DAC A, selects the register to be read. Note that only one DAC register can be selected during readback. The remaining three address bits (which include the two don't care bits) must be set to Logic 0. The remaining data bits in the write sequence are ignored. If more than one address bit is selected or no address bit is selected, DAC Channel A is read back by default. During the next SPI write, the data that appears on the SDO output contains the data from the previously addressed register. Operating Mode Normal Operation Mode Power-Down Modes 1 k to GND 100 k to GND Three-State 1. 2. Either or both DACs (DAC B, DAC A) can be powered down to the selected mode by setting the corresponding bits. See Table 12 for the contents of the input shift register during the power-down/ power-up operation. 1 0 1 The output is connected internally to GND through a 1 k resistor. The output is connected internally to GND through a 100 k resistor. The output is left open-circuited (three-state). The output stage is illustrated in Figure 46. AMPLIFIER DAC POWER-DOWN OPERATION The AD5689R/AD5687R contain three separate power-down modes. Command 0100 controls the power-down function (see Table 9). These power-down modes are software-programmable by setting eight bits, Bit DB7 to Bit DB0, in the input shift register. There are two bits associated with each DAC channel. Table 11 explains how the state of the two bits corresponds to the mode of operation of the device. 0 1 1 When both Bit PDx1 and Bit PDx0 (where x is the channel that is selected) in the input shift register are set to 0, the parts work normally, with a normal power consumption of 4 mA at 5 V. However, for the three power-down modes of the AD5689R/ AD5687R, the supply current falls to 4 A at 5 V. Not only does the supply current fall, but the output stage is also internally switched from the output of the amplifier to a resistor network of known values. This switchover has the advantage that the output impedance of the part is known while the part is in power-down mode. The three power-down options are as follows: Write 0x900000 to the AD5689R/AD5687R input register. This setting configures the part for read mode with the Channel A DAC register selected. Note that all data bits, DB15 to DB0, are don't care bits. Follow this write operation with a second write, a nop operation, 0x000000 (0xF00000 in daisy-chain mode). During this write, the data from the register is clocked out on the SDO line. DB23 to DB20 contain undefined data, and the last 16 bits contain the DB19 to DB4 DAC register contents. PDx0 0 VOUTX POWER-DOWN CIRCUITRY RESISTOR NETWORK 11256-048 For example, to read back the DAC register for Channel A, implement the following sequence: PDx1 0 Figure 46. Output Stage During Power-Down The bias generator, output amplifier, resistor string, and other associated linear circuitry are shut down when the power-down mode is activated. However, the contents of the DAC register are unaffected when in power-down, and the DAC register can be updated while the device is in power-down mode. The time that is required to exit power-down is typically 4.5 s for VDD = 5 V. To further reduce the current consumption, the on-chip reference can be powered off (see the Internal Reference Setup section). Table 12. 24-Bit Input Shift Register Contents of Power-Down/Power-Up Operation1 DB23 (MSB) 0 DB22 1 DB21 0 DB20 0 Command bits (C3 to C0) 1 DB19 to DB16 X DB15 to DB8 X Address bits; don't care DB7 DB6 PDB1 PDB0 Power-down, select DAC B X = don't care. Rev. B | Page 22 of 28 DB5 1 DB4 1 Set to 1 DB3 1 DB2 1 Set to 1 DB1 DB0 (LSB) PDA1 PDA0 Power-down, select DAC A Data Sheet AD5689R/AD5687R updated by taking LDAC low after SYNC is taken high. The update then occurs on the falling edge of LDAC. LOAD DAC (HARDWARE LDAC PIN) The AD5689R/AD5687R DACs have double buffered interfaces consisting of two banks of registers: input registers and DAC registers. The user can write to any combination of the input registers. Updates to the DAC register are controlled by the LDAC pin. LDAC MASK REGISTER Command 0101 is reserved for a software LDAC mask function, which allows the address bits to be ignored. A write to the DAC, using Command 0101, loads the 4-bit LDAC mask register (DB3 to DB0). The default setting for each channel is 0; that is, the LDAC pin works normally. Setting the selected bit to 1 forces the DAC channel to ignore transitions on the LDAC pin, regardless of the state of the hardware LDAC pin. This flexibility is useful in applications where the user wishes to select which channels respond to the LDAC pin. OUTPUT AMPLIFIER VREF 16-/12-BIT DAC VOUTX DAC REGISTER LDAC The LDAC mask register gives the user extra flexibility and control over the hardware LDAC pin (see Table 13). Setting an LDAC bit (DB3, DB0) to 0 for a DAC channel means that the update of this channel is controlled by the hardware LDAC pin. INPUT REGISTER INTERFACE LOGIC SDO SDIN Table 13. LDAC Overwrite Definition 11256-049 SCLK SYNC Load LDAC Register LDAC Bits (DB3, DB0) 0 1 Figure 47. Simplified Diagram of Input Loading Circuitry for a Single DAC Instantaneous DAC Updating (LDAC Held Low) LDAC is held low while data is clocked into the input register using Command 0001. Both the addressed input register and the DAC register are updated on the rising edge of SYNC, and then the output begins to change (see Table 14 and Table 15). 1 LDAC Pin LDAC Operation 1 or 0 X1 Determined by the LDAC pin. DAC channels update and override the LDAC pin. DAC channels see the LDAC pin as set to 1. X = don't care. Deferred DAC Updating (LDAC Pulsed Low) LDAC is held high while data is clocked into the input register using Command 0001. Both DAC outputs are asynchronously Table 14. 24-Bit Input Shift Register Contents for LDAC Operation1 DB23 (MSB) 0 DB22 1 DB21 0 DB20 1 DB19 X Command bits (C3 to C0) 1 DB18 X DB17 X DB16 X Address bits, don't care DB2 0 DB1 0 DB0 (LSB) DAC A DB15 to DB4 X DB3 DAC B Don't care Setting the LDAC bit to 1 overrides the LDAC pin X = don't care. Table 15. Write Commands and LDAC Pin Truth Table1 Command 0001 Description Write to Input Register n (dependent on LDAC) 0010 Update DAC Register n with contents of Input Register n 0011 Write to and update DAC Channel n Hardware LDAC Pin State VLOGIC GND2 VLOGIC GND VLOGIC GND Input Register Contents Data update Data update No change No change Data update Data update DAC Register Contents No change (no update) Data update Updated with input register contents Updated with input register contents Data update Data update A high-to-low hardware LDAC pin transition always updates the contents of the DAC register with the contents of the input register on channels that are not masked (blocked) by the LDAC mask register. 2 When the LDAC pin is permanently tied low, the LDAC mask bits are ignored. 1 Rev. B | Page 23 of 28 AD5689R/AD5687R Data Sheet HARDWARE RESET (RESET) SOLDER HEAT REFLOW RESET is an active low reset that allows the outputs to be cleared to either zero scale or midscale. The clear code value is user selectable via the power-on reset select pin (RSTSEL). RESET must be kept low for a minimum amount of time to complete the operation (see Figure 2). When the RESET signal is returned high, the output remains at the cleared value until a new value is programmed. The outputs cannot be updated with a new value while the RESET pin is low. There is also a software executable reset function that resets the DAC to the power-on reset code. Command 0110 is designated for this software reset function (see Table 9). Any events on LDAC during a power-on reset are ignored. If the RESET pin is pulled low at power-up, the device does not initialize correctly until the pin is released. As with all IC reference voltage circuits, the reference value experiences a shift induced by the soldering process. Analog Devices, Inc., performs a reliability test, called precondition, that mimics the effect of soldering a device to a board. The output voltage specification that is listed in Table 2 includes the effect of this reliability test. Figure 48 shows the effect of solder heat reflow (SHR) as measured through the reliability test (precondition). PRESOLDER HEAT REFLOW 50 HITS 40 RESET SELECT PIN (RSTSEL) 30 The AD5689R/AD5687R contain a power-on reset circuit that controls the output voltage during power-up. When the RSTSEL pin is connected low (to GND), the output powers up to zero scale. Note that this is outside the linear region of the DAC. When the RSTSEL pin is connected high (to VLOGIC), VOUTX powers up to midscale. The output remains powered up at this level until a valid write sequence is sent to the DAC. To ensure that the RSTSEL pin functions correctly, a power sequence must be followed. Power up VLOGIC first, before VDD; otherwise, VOUT remains at zero scale. INTERNAL REFERENCE SETUP Command 0111 is reserved for setting up the internal reference (see Table 9). By default, the on-chip reference is on at power-up. To reduce the supply current, this reference can be turned off by setting the software-programmable bit, DB0, as shown in Table 17. Table 16 shows how the state of the bit corresponds to the mode of operation. 20 10 2.498 2.499 2.500 2.501 2.502 VREF (V) 11256-050 0 Figure 48. SHR Reference Voltage Shift LONG-TERM TEMPERATURE DRIFT Figure 49 shows the change in the VREF (ppm) value after 1000 hours at 25C ambient temperature. 140 120 100 80 60 Table 16. Reference Setup Register 40 Action Reference on (default) Reference off 20 0 -20 0 100 200 300 400 500 600 700 800 900 1000 Figure 49. Reference Drift Through to 1000 Hours Table 17. 24-Bit Input Shift Register Contents for Internal Reference Setup Command1 DB23 (MSB) 0 1 DB22 DB21 DB20 1 1 1 Command bits (C3 to C0) DB19 X DB18 DB17 X X Address bits (A3 to A0) X = don't care. Rev. B | Page 24 of 28 DB16 X DB15 to DB1 X Don't care DB0 (LSB) 1 or 0 Reference setup register 11256-155 Internal Reference Setup Register (DB0) 0 1 POSTSOLDER HEAT REFLOW 60 Data Sheet AD5689R/AD5687R 9 THERMAL HYSTERESIS 8 Thermal hysteresis is the voltage difference induced on the reference voltage by sweeping the temperature from ambient to cold, to hot, and then back to ambient. 7 6 5 4 3 2 1 0 -200 -150 -100 -50 DISTORTION (ppm) Figure 50. Thermal Hysteresis Rev. B | Page 25 of 28 0 50 11256-052 HITS Thermal hysteresis data is shown in Figure 50. It is measured by sweeping the temperature from ambient to -40C, next to +105C, and then returning to ambient. The VREF delta is then measured between the two ambient measurements and shown in blue in Figure 50. The same temperature sweep and measurements are immediately repeated and the results are shown in red in Figure 50. FIRST TEMPERATURE SWEEP SUBSEQUENT TEMPERATURE SWEEPS AD5689R/AD5687R Data Sheet APPLICATIONS INFORMATION MICROPROCESSOR INTERFACING Microprocessor interfacing to the AD5689R/AD5687R is achieved via a serial bus using a standard protocol that is compatible with DSP processors and microcontrollers. The communications channel requires a 3-wire or 4-wire interface consisting of a clock signal, a data signal, and a synchronization signal. Each device requires a 24-bit data-word with data valid on the rising edge of SYNC. AD5689R/AD5687R TO ADSP-BF531 INTERFACE The SPI interface of the AD5689R/AD5687R is designed to be easily connected to industry-standard DSPs and microcontrollers. Figure 51 shows the AD5689R/AD5687R connected to an Analog Devices Blackfin(R) DSP. The Blackfin has an integrated SPI port that connects directly to the SPI pins of the AD5689R/AD5687R. AD5689R/ AD5687R which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. In systems where there are many devices on one board, it is often useful to provide some heat sinking capability to allow the power to dissipate easily. Each AD5689R or AD5687R has an exposed paddle beneath the device. Connect this paddle to the GND supply for the part. For optimum performance, use special considerations to design the motherboard and to mount the package. For enhanced thermal, electrical, and board level performance, solder the exposed paddle on the bottom of the package to the corresponding thermal land paddle on the PCB. Design thermal vias into the PCB land paddle area to further improve heat dissipation. The GND plane on the device can be increased (as shown in Figure 53) to provide a natural heat sinking effect. AD5689R/ AD5687R ADSP-BF531 GND PLANE Figure 51. ADSP-BF531 Interface to the AD5689R/AD5687R BOARD AD5689R/AD5687R TO SPORT INTERFACE The Analog Devices ADSP-BF527 has one SPORT serial port. Figure 52 shows how one SPORT interface can be used to control the AD5689R/AD5687R. AD5689R/ AD5687R ADSP-BF527 GPIO0 GPIO1 SYNC SCLK SDIN LDAC RESET 11256-054 SPORT_TFS SPORT_TSCK SPORT_DTO Figure 52. SPORT Interface to the AD5689R/AD5687R LAYOUT GUIDELINES Figure 53. Paddle Connection to Board GALVANICALLY ISOLATED INTERFACE In many process control applications, it is necessary to provide an isolation barrier between the controller and the unit being controlled to protect and isolate the controlling circuitry from any hazardous common-mode voltages that may occur. The iCoupler(R) products from Analog Devices provide voltage isolation in excess of 2.5 kV. The serial loading structure of the AD5689R/ AD5687R makes these parts ideal for isolated interfaces because the number of interface lines is kept to a minimum. Figure 54 shows a 4-channel isolated interface to the AD5689R/AD5687R using an ADuM1400. For additional information, visit www.analog.com/icouplers. CONTROLLER In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. Design the PCB on which the AD5689R/ AD5687R are mounted so that the AD5689R/AD5687R lie on the analog plane. Provide the AD5689R/AD5687R with ample supply bypassing of 10 F in parallel with 0.1 F on each supply, located as close to the package as possible, ideally right up against the device. The 10 F capacitor is of the tantalum bead type. Use a 0.1 F capacitor with low effective series resistance (ESR) and low effective series inductance (ESI), such as the common ceramic types, SERIAL CLOCK IN SERIAL DATA OUT SYNC OUT LOAD DAC OUT ADuM14001 VIA VIB VIC VID ENCODE DECODE ENCODE DECODE ENCODE DECODE ENCODE DECODE 1 ADDITIONAL PINS OMITTED FOR CLARITY. Figure 54. Isolated Interface Rev. B | Page 26 of 28 VOA VOB VOC VOD TO SCLK TO SDIN TO SYNC TO LDAC 11256-056 LDAC RESET 11256-055 PF9 PF8 SYNC SCLK SDIN 11256-053 SPISELx SCK MOSI Data Sheet AD5689R/AD5687R OUTLINE DIMENSIONS PIN 1 INDICATOR 0.30 0.23 0.18 0.50 BSC 13 PIN 1 INDICATOR 16 1 12 1.75 1.60 SQ 1.45 EXPOSED PAD 9 TOP VIEW 0.80 0.75 0.70 4 5 8 0.50 0.40 0.30 BOTTOM VIEW FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE 0.25 MIN 08-16-2010-E 3.10 3.00 SQ 2.90 COMPLIANT TO JEDEC STANDARDS MO-220-WEED-6. Figure 55. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 3 mm x 3 mm Body, Very Very Thin Quad (CP-16-22) Dimensions shown in millimeters 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.65 BSC 0.30 0.19 COPLANARITY 0.10 0.20 0.09 SEATING PLANE 8 0 COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 56. 16-Lead Thin Shrink Small Outline Package [TSSOP] (RU-16) Dimensions shown in millimeters Rev. B | Page 27 of 28 0.75 0.60 0.45 AD5689R/AD5687R Data Sheet ORDERING GUIDE Model1 AD5689RACPZ-RL7 AD5689RBCPZ-RL7 AD5689RARUZ AD5689RARUZ-RL7 AD5689RBRUZ AD5689RBRUZ-RL7 AD5687RBCPZ-RL7 AD5687RBRUZ AD5687RBRUZ-RL7 EVAL-AD5687RSDZ EVAL-AD5689RSDZ 1 Resolution 16 Bits 16 Bits 16 Bits 16 Bits 16 Bits 16 Bits 12 Bits 12 Bits 12 Bits Temperature Range -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C Accuracy 8 LSB INL 2 LSB INL 8 LSB INL 8 LSB INL 2 LSB INL 2 LSB INL 1 LSB INL 1 LSB INL 1 LSB INL Reference Tempco (ppm/C) 5 (typ) 5 (max) 5 (typ) 5 (typ) 5 (max) 5 (max) 5 (max) 5 (max) 5 (max) Z = RoHS Compliant Part. (c)2013-2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D11256-0-3/17(B) Rev. B | Page 28 of 28 Package Description 16-Lead LFCSP_WQ 16-Lead LFCSP_WQ 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead LFCSP_WQ 16-Lead TSSOP 16-Lead TSSOP Evaluation Board Evaluation Board Package Option CP-16-22 CP-16-22 RU-16 RU-16 RU-16 RU-16 CP-16-22 RU-16 RU-16 Branding DLU DL2 DL1