6N139 www.vishay.com Vishay Semiconductors High Speed Optocoupler, 100 kBd, Low Input Current, Photodiode Darlington Output FEATURES * High current transfer ratio, 500 % NC 1 8 VCC * Low input current, 1.6 mA A 2 7 VB * High common mode rejection, 500 V/s C 3 6 VO NC 4 5 GND DESIGN SUPPORT TOOLS * Adjustable bandwidth-access to base * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS click logo to get started * Microprocessor system interface * PLC, ATE input / output isolation Models Available Design Tools * EIA RS232 line receiver Available * TTL, CMOS voltage level translation DESCRIPTION * Multiplexed data transmission High common mode transient immunity and very high current ratio together with 5300 VRMS insulation are achieved by coupling and LED with an integrated high gain photo detector in an eight pin dual-in-line package. Separate pins for the photo diode and output stage enable TTL compatible saturation voltages with high speed operation. Access to the base terminal allows adjustment to the gain bandwidth. The 6N139 is suited for low power logic applications involving CMOS and low power TTL applications. A 400 % current transfer ratio with only 0.5 mA of LED current is guaranteed. * Digital control power supply * Ground loop and electrical noise elimination AGENCY APPROVALS * UL 1577 * cUL * DIN EN 60747-5-5 (VDE 0884-5), available with option 1 Caution: Due to the small geometries of this device, it should be handled with Electrostatic Discharge (ESD) precautions. Proper grounding would prevent damage further and/or degradation which may be induced by ESD. ORDERING INFORMATION DIP 6 N 1 3 # - X 0 # # T 7.62 mm PART NUMBER PACKAGE OPTION TAPE AND REEL Option 7 > 0.7 mm AGENCY CERTIFIED/PACKAGE UL, cUL DIP-8 SMD-8, option 7 SMD-8, option 9 UL, cUL, VDE (option 1) DIP-8 SMD-8, option 7 SMD-8, option 9 Option 9 > 0.1 mm CTR (%) 1.6 mA > 500 6N139 6N139-X007, 6N139-X007T 6N139-X009, 6N139-X009T > 500 6N139-X001 6N139-X017T 6N139-X019T Note * For additional information on the available options refer to option information Rev. 1.7, 24-Sep-2018 Document Number: 83605 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage VR 5 V Forward current IF 25 mA Average input current If(avg) 20 mA Input power dissipation Pdiss 35 mW VCC, VO OUTPUT Supply and output voltage Emitter base reverse voltage Peak input current Peak transient input current Pin 8 to 5, pin 6 to 5 -0.5 to 18 V Pin 5 to 7 0.5 V 50 % duty cycle - 1 ms pulse width 40 mA tp 1 s, 300 pps 1 A IO 60 mA Pdiss 100 mW Storage temperature Tstg -55 to +150 C Operating temperature Tamb -55 to +100 C Tsld 260 C Output current Pin 6 Output power dissipation COUPLER Lead soldering temperature t = 10 s Note * Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability ELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT IF = 1.6 mA VF - 1.4 1.7 V IR = 10 A BVR 5 - - V f = 1 MHz, VF = 0 CIN - 25 - pF - -1.8 - mV/C INPUT Input forward voltage Input reverse breakdown voltage Input capacitance Temperature coefficient of forward voltage IF = 1.6 mA OUTPUT Logic low, output voltage (1) IF = 1.6 mA, IO = 8 mA, VCC = 4.5 V VOL - 0.1 0.4 V IF = 5 mA, IO = 15 mA, VCC = 4.5 V VOL - 0.15 0.4 V IF = 12 mA, IO = 24 mA, VCC = 4.5 V VOL - 0.25 0.4 V Logic high, output current (1) IF = 0 mA, VCC = 18 V IOH - 0.05 100 A Logic low supply current (1) IF = 1.6 mA, VO = OPEN, VCC = 18 V ICCL - 0.2 1.5 mA Logic high supply current (1) IF = 0 mA, VO = OPEN, VCC = 18 V ICCH - 0.001 10 A - - 1 A - 0.6 - pF COUPLER Input output insulation leakage current Coupling capacitance 45 % relative humidity, Tamb = 25 C, t = 5 s, VIO = 3000 VDC f = 1 MHz CIO Notes * Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements (1) Pin 7 open Rev. 1.7, 24-Sep-2018 Document Number: 83605 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors CURRENT TRANSFER RATIO PARAMETER Current transfer ratio (1) TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT IF = 0.5 mA, VO = 0.4 V, VCC = 4.5 V CTR 400 1600 - % IF = 1.6 mA, VO = 0.4 V, VCC = 4.5 V CTR 500 2000 - % Notes (1) Pin 7 open SAFETY AND INSULATION RATINGS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION Climatic classification SYMBOL VALUE According to IEC 68 part 1 Comparative tracking index UNIT 55 / 100 / 21 Insulation group IIIa CTI 175 Maximum rated withstanding isolation voltage According to UL 1577, t = 1 min VISO 5300 VRMS Maximum transient isolation voltage According to DIN EN 60747-5-5 VIOTM 8000 Vpeak Maximum repetitive peak isolation voltage According to DIN EN 60747-5-5 VIORM 890 Vpeak Tamb = 25 C, VIO = 500 V RIO 1012 Tamb = 100 C, VIO = 500 V RIO 1011 PSO 500 mW Input safety current ISI 300 mA Input safety temperature TS 175 C Isolation resistance Output safety power Creepage distance DIP-8 Clearance distance Creepage distance SMD-8, option 7, SMD-8, option 9 Clearance distance Insulation thickness DTI 7 mm 7 mm 8 mm 8 mm 0.4 mm Note * As per IEC 60747-5-5, 7.4.3.8.2, this optocoupler is suitable for "safe electrical insulation" only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits SWITCHING CHARACTERISTICS PARAMETER Propagation delay time to logic low at output TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT IF = 0.5 mA, RL = 4.7 k tPHL - 6 25 s IF = 12 mA, RL = 270 tPHL - 0.6 1 s Propagation delay time to logic high at output IF = 0.5 mA, RL = 4.7 k tPLH - 4 60 s Propagation delay time to logic high at output IF = 12 mA, RL = 270 tPLH - 1.5 7 s I 10 % duty cycle 1/f < 100 s 0 1 Pulse generator ZO = 5 0 tr = 5 n s +5V 8 5V V IF 2 (saturated response) 7 RL 3 6 0.1 F I F = monitor 4 Rm 5 1.5 V 1.5 V VOL VO t PLH t PHL C L = 15 pF VO (non-saturated response) 5V 10 % tf isfh6318t_01 90 % 90 % 10 % tr Fig. 1 - Switching Test Circuit Rev. 1.7, 24-Sep-2018 Document Number: 83605 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors COMMON MODE TRANSIENT IMMUNITY PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Common mode transient immunity, logic high level output (1) IF = 0 mA, RL = 2.2 k, RCC = 0, |VCM| = 10 VP-P |CMH| - 500 - V/s Common mode transient immunity, logic low level output (1) IF = 16 mA, RL = 2.2 k, RCC = 0, |VCM| = 10 VP-P |CML| - - 500 - V/s Note (1) In applications where dV/dt may exceed 50 000 V/s (such as state discharge) a series resistor, R CC should be included to protect IC from destructively high surge currents. The recommend value is RCC [(1 V)/(0.15 IF (mA)] k RCC (see Note 6) 1 8 2 7 IF +5V 220 VCM 90 % RL A 3 6 4 5 90 % 0 V 10 % 0.1 F 10 % tr tf t f + t f =16 ns VO B VO 5V Switch at A: IF = 0 mA VCC VCM + - VO isfh6318t_02 VOL Switch at B: IF = 1.6 mA Pulse Generator Fig. 2 - Test Circuit for Transient Immunity and Typical Waveforms TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 120 100 Total Power (mW) IF - LED Current (mA) 30 20 10 Detector 80 60 40 Emitter 20 0 22418 0 0 25 50 75 100 125 Tamb - Ambient Temperature (C) Fig. 2 - Permissible Forward LED Current vs. Temperature Rev. 1.7, 24-Sep-2018 0 22419 25 50 75 100 125 Tamb - Ambient Temperature (C) Fig. 3 - Permissible Power Dissipation vs. Temperature Document Number: 83605 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS (in millimeters) DIP-8 3.10 0.25 7.62 typ. 10.16 max. 9.75 0.15 0.95 0.20 0.70 0.20 6.00 0.25 3.55 0.20 6.70 0.15 1.27 0.10 0.50 0.10 2.54 nom. 7 typ. 3 x 2.54 = 7.62 8 7 6 5 1 2 3 4 .10 0.25 0 PIN ONE I.D. 22672 SMD-8, Option 7 10.05 0.25 10.16 max. 7.62 typ. 9.75 0.15 6.70 0.15 0.25 0.10 8.00 min. 8.40 min. 1.27 0.10 0.75 0.25 2.54 nom. 3 x 2.54 = 7.62 PIN ONE I.D. 0.70 0.20 3.55 0.20 0.95 0.20 8 7 6 5 1 2 3 4 Leads Coplanarity 0.10 max. 22674 Rev. 1.7, 24-Sep-2018 Document Number: 83605 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors SMD-8, Option 9 9.78 0.25 7.62 typ. 10.16 max. 9.75 0.15 0.95 0.20 3.55 0.20 0.18 0.08 0.25 0.10 6.70 0.15 0.75 0.20 1.27 0.10 2.54 nom. 8.00 min. Leads Coplanarity 0.10 max. 3 x 2.54 = 7.62 PIN ONE I.D. 8 7 6 5 1 2 3 4 22675 PACKAGE MARKING 6N139 V YWW 68 Fig. 3 - Example of 6N139-X017T Note * VDE logo is only marked on option 1 parts * Tape and reel suffix (T) is not part of the package marking Rev. 1.7, 24-Sep-2018 Document Number: 83605 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors PACKING INFORMATION (in millimeters) Tube 528 0.2 330 0.5 260 0.5 200 0.5 150 0.5 125 0.5 - 1.0 30 0.5 B VISHAY OPTOSEMICONDUCTOR MADE IN MALAYSIA ANTISTATIC Detail B Detail A A - 1.0 - 1.0 3 0.5 - 1.0 380 1 0.7 0.5 1.0 14 x 13 x 10 = 130 17996-3 Fig. 4 - Shipping Tube Specifications for DIP-8 Packages DEVICES PER TUBS TYPE UNITS/TUBE TUBES/BOX UNITS/BOX DIP-8 50 40 2000 DIP-8 12 0.3 B 6.6 0.3 Transparent rigid PVC 2.7 0.2 R 0. 1 6 4.4 0.3 0. 5 11 0.3 R 0.6 0.1 10 A // 0.2 B Detail A Detail B 5.7 0.15 17996-4 Section A - B Not to scale Fig. 5 - Tube Shipping Medium Rev. 1.7, 24-Sep-2018 Document Number: 83605 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors Tape and Reel ESD sticker Tape slot in core 330 (13") Top cover tape Regular, special or bar code label Embossed carrier Embossment 17999 17998 Fig. 6 - Tape and Reel Shipping Medium Fig. 7 - Tape and Reel Shipping Medium SMD-8 (option 7) Pin 1 and top of component 0.35 (0.014) 4 0.1 (1.57 0.004) 2 0.05 (0.079 0.002) 1.5 (0.059) min. 10 pitch cumulative tolerance on tape 0.2 (0.008) 1.75 0.1 (0.069 0.004) Top cover tape 10.41 (0.410) 7.5 0.05 16.0 0.3 (0.295 0.002) (0.630 0.012) 4.7 (0.185) 10.21 (0.402) 13.3 (0.523) 12.0 (0.472) 0.1 (0.004) max. Embossment Center lines of cavity 18008 1.5 (0.059) Direction of feed Fig. 8 - Tape and Reel Packing (1000 pieces on Reel) SMD-8 (option 9) Pin 1 and top of component 4 0.1 (1.57 0.004) 2 0.05 (0.079 0.002) 1.5 (0.059) min. 10 pitch cumulative tolerance on tape 0.2 (0.008) 0.35 (0.014) 1.75 0.1 (0.069 0.004) Top cover tape 10.2 (0.402) 7.5 0.05 16.0 0.3 (0.295 0.002) (0.630 0.012) 4.17 (0.164) 10.31 (0.406) 13.3 (0.523) 12.0 (0.472) 0.1 (0.004) max. 18009 Embossment Center lines of cavity 1.5 (0.059) Direction of feed Fig. 9 - Tape and Reel Shipping Medium Rev. 1.7, 24-Sep-2018 Document Number: 83605 8 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6N139 www.vishay.com Vishay Semiconductors SOLDER PROFILES Axis Title Axis Title 10000 5s 10000 300 Lead temperature 1000 ca. 2 K/s ca. 200 K/s 150 Full line: typical Dotted lines: process limits Second wave 100 C to 130 C 100 100 2 K/s 50 2nd line Temperature (C) 200 10 100 150 200 Max. 30 s 150 Max. 120 s 100 Max. 100 s Max. ramp down 6 C/s 100 Max. ramp up 3 C/s Fig. 10 - Wave Soldering Double Wave Profile According to J.STD-020 for DIP-8 Devices 10 0 0 250 Time (s) 948626 1000 200 50 0 50 245 C ca. 5 K/s Forced cooling 0 255 C 240 C 217 C 250 235 C to 260 C First wave 1st line 2nd line 2nd line Temperature (C) 250 Max. 260 C 1st line 2nd line 300 19841 50 100 150 200 250 300 Time (s) Fig. 11 - Lead (Pb)-free Reflow Solder Profile According to J-STD-020 for SMD-8 Devices HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 Floor life: unlimited Conditions: Tamb < 30 C, RH < 85 % Moisture sensitivity level 1, according to J-STD-020 Rev. 1.7, 24-Sep-2018 Document Number: 83605 9 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2021 1 Document Number: 91000