3MTM 4-Wall, Tripolarized Header .050" x .100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle 810 Series * Tripolarized for robust alignment when mating to 820 series socket * 50 mil x 100 mil halves the connector length vs. traditional 100 mil x 100 mil products * Latching Ejector for rugged high performance applications * Available for through hole or surfacemount attachment * High temperature plastic for lead free surfacemount or Paste-in-Hole soldering methods * Four-wall shroud provides contact protection * Contacts: 20, 26, 36, 40, 50, 60, 68, 80 and 100 * See the Regulatory Information Appendix (RIA) in the "RoHS compliance" section of www.3Mconnectors.com for compliance information Date Modified: April 2, 2013 TS-0253-K Sheet 1 of 7 Physical Insulation: Material: High Temperature Plastic (LCP) Flammability: UL 94V-0 Color: Black Contact: Material: Copper Alloy Plating: Underplating: 100 " [2.54 mm] Nickel Wiping Area: 30 " [0.76 mm] Gold Solder Tails: Matte Tin or Tin Lead (See Ordering Information) Marking: 3M Logo, Part Number and Orientation Triangle Mating Compatibility: 820 Series (TS-0254) Electrical Current Rating: 3.00 A, 1 Contact Powered 2.00 A, 4 Contacts Powered 0.75 A, All Contacts powered Rating Conditions: EIA-364-070 Method 2, 30 degrees C maximum temperature rise, 20% derated. Reference appropriate 3M Product Specification for detailed current derating curves. Insulation Resistance: > 1 x 109 at 500 VDC Withstanding Voltage: 500 VRMS at Sea Level Environmental Temperature Rating: -55C to +105C Process Rating: Maximum 260C (Profile per J-STD-020C) Moisture Sensitivity Level: 1 (per J-STD-020C) UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM 4-Wall, Tripolarized Header .050" x .100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle Table 1 Inch [Imm] C .0 .00 .000 .1 .01 .005 Dimensions Contact Quantity Tolerance Unless Noted Inch [ ] Dimensions for Reference Only A B C D Short (Ref.) D Long (Ref.) 020 1.060 [26.92] 0.722 [18.34] 0.500 [12.70] 1.671 [42.44] 1.842 [46.79] 026 1.210 [30.73] 0.872 [22.15] 0.650 [16.51] 1.821 [46.25] 1.992 [50.60] 036 1.460 [37.08] 1.122 [28.50] 0.900 [22.86] 2.071 [52.60] 2.242 [56.95] 040 1.560 [39.62] 1.222 [31.04] 1.000 [25.40] 2.171 [55.14] 2.342 [59.49] 050 1.810 [45.97] 1.472 [37.39] 1.250 [31.75] 2.421 [61.49] 2.592 [65.84] 060 2.060 [52.32] 1.722 [43.74] 1.500 [38.10] 2.671 [67.84] 2.842 [72.19] 068 2.260 [57.40] 1.922 [48.82] 1.700 [43.18] 2.871 [72.92] 3.042 [77.27] 080 2.560 [65.02] 2.222 [56.44] 2.000 [50.80] 3.171 [80.54] 3.342 [84.89] 100 3.060 [77.72] 2.722 [69.14] 2.500 [63.50] 3.671 [93.24] 3.842 [97.59] A B C .015 X .015 [0.38] X [0.38] 2X .092 [2.34] See Note 1 Position 2 .310 [7.87] 810 Series Position 1 .100 Ref [2.54] .015 X .015 [0.38] X [0.38] Table 2 .050 Typ [1.27] PCB Thickness "F" Solder Tail Length .010 .062 [1.57] .090 [2.29] .094 [2.39] .112 [2.84] .125 [3.18] .143 [3.63] D Long Latch Short Latch .165 .010 [ 4.19 ] .440 .010 [11.18] .828 Ref [ 21.03 ] .620 Ref [ 15.75 ] .405 [10.29] 2X O.116 [2.95] .160 Ref [4.06] .265 [6.73] .306 Ref [7.77] .140 .010 [3.56] .015 [0.38] Position 1 Orientation Triangle Notes: 1. This polarization bump does not exist on the 20 position header. 2. Recommended Notes:to be mated to the .050" X .100" Wiremount Socket 820 Series. Ordering Information "F" (See Table 2) PTH Right Angle Header 81XXX - 5X0X03 - XX Ejector Latches (If Ordered Separately) Contact Quantity (See Table 1) Long Latches 3505-28B (black) Short Latches 3505-29B (black) .105 [2.67] Ejector/Latch System: 0 = None (Special Order) 5 = With Short Ejectors Installed (Special Order) 6 = With Long Ejector Latches Installed (Standard) Plating suffix: blank = 125 " tin lead tails (RIA E3 & C2 apply) RB = 250 " matte tin tails (RIA E1 & C1 apply) Contact Tail: 2 = Solder Tail for .062 [ 1.57 ] PC Board (Standard) 3 = Solder Tail for .094 [ 2.39 ] PC Board (Special Order) 4 = Solder Tail for .125 [ .318 ] PC Board (Special Order) TS-0253-K Sheet 2 of 7 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM 4-Wall, Tripolarized Header .050" x .100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle .050 .002 [1.27] O.024 .003 Typ [0.64] Table 3 Ejector Latches *Solder Thief Solder Pads (See Note 2) .100 .002 [2.54] 810 Series Dimension E Min None .575 [14.61] Long 1.010 [25.65] Short .885 [22.48] .045 - .060 [1.14] - [1.52] .025 - .035 [0.64] - [0.89] *Solder Thief Solder Pads required only on Solder side of PC Board. View A E C .002 .025 .002 [0.64] .050 .002 Typ [1.27] Tolerance Noncumulative .355 Max [9.02] .305 Min [7.75] Position 2 Flow Solder Direction View A Position 1 2X O .109 .002 [2.77] O.024 .003 Typ [0.64] .100 .002 [2.54] .160 .002 [4.06] Recommended Mounting Hole Pattern PTH Right Angle Header (shown for mounting side of PC Baord) Notes: 1. Recommended to process PC Boards through the solder bath such that the connector enters end first (two solder tails at a time). This will help prevent solder bridging. 2. A Dummy or Solder Thief Solder Pad at the end of each row is recommended on the bottom or solder side of the PC Board in order to help prevent solder bridging on the end solder tails. The solder thiefs are only required on the end of the rows which leave the solder bath last. 3. In order to facilitate soldering it is recommended that ejector latches be installed after the soldering process. 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com TS-0253-K Sheet 3 of 7 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM 4-Wall, Tripolarized Header .050" x .100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle 810 Series Table 4 Dimensions Contact Quantity A B C Short (Ref.) C Long (Ref.) D 020 1.060 [26.92] 0.722 [18.34] 1.671 [42.44] 1.842 [46.79] 0.860 [21.84] 026 1.210 [30.73] 0.872 [22.15] 1.821 [46.25] 1.992 [50.60] 1.010 [25.65] 036 1.460 [37.08] 1.122 [28.50] 2.071 [2.60] 2.242 [56.95] 1.260 [32.00] 040 1.560 [39.62] 1.222 [31.04] 2.171 [55.14] 2.342 [59.49] 1.360 [34.54] 050 1.810 [45.97] 1.472 [37.39] 2.421 [61.49] 2.592 [65.84] 1.610 [40.89] 060 2.060 [52.32] 1.722 [43.74] 2.671 [67.84] 2.842 [72.19] 1.860 [47.24] 068 2.260 [57.40] 1.922 [48.82] 2.871 [72.92] 3.042 [77.27] 2.060 [52.32] 080 2.560 [65.02] 2.222 [56.44] 3.171 [80.54] 3.342 [84.89] 2.360 [59.94] 100 3.060 [77.72] 2.722 [69.14] 3.671 [93.24] 3.842 [97.59] 2.860 [72.64] A Table 5 B .310 [7.87] C PCB Thickness "F" Solder Tail Length .010 .062 [1.57] .092 [2.34] .094 [2.39] .110 [2.79] See Note 1 Position 2 Position 1 .100 Ref [2.54] .015 X .015 [ 0.38 ] X [ 0.38 ] .050 Typ [1.27] .265 [6.73] .165 .010 .440 4.18 .05 Ref Contact Mating Point .010 .140 .010 11.17 .828 Ref 21.03 .100 [2.54] .620 Ref 15.75 .405 "F" (See Table 2) 10.29 2X .092 .015 2.34 .38 .015 X.015 [0.38 X 0.38] 2XO .116 2,95 Position 1 Orientation Triangle Optional Press fit post mount alignment feature D Ordering Information PTH Straight Header 81XXX - 6X0X0X - XX Ejector Latches Contact Quantity (See Table 4) (If Ordered Separately) Long Latches 3505-28B (black) Short Latches 3505-29B (black) Notes: 1. This polarization bump does not exist on the 20 position header. 2. Recommended to be mated to the .050" x .100" 820 Series Socket. Ejector/Latch System: 0 = None (Special Order) 5 = With Short Ejectors Installed (Special Order) 6 = With Long Ejector Latches Installed (Standard) 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com Plating suffix: blank = 125 " tin lead tails (RIA E3 & C2 apply) RB = 250 " matte tin tails (RIA E1 & C1 apply) Board Mounting Options: 1 = None (Special Order) 3 = Press fit posts both ends (Standard) Contact Tail: 2 = Solder Tail for .062 [ 1.57 ] PC Board (Standard) 3 = Solder Tail for .094 [ 2.39 ] PC Board (Special Order) 4 = Solder Tail for .125 [ .318 ] PC Board (Special Order) TS-0253-K Sheet 4 of 7 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM 4-Wall, Tripolarized Header .050" x .100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle Table 6 .050 .002 [1.27] .025 .003 [0.64] .100 .002 [2.54] Ejector/Latches *Solder Thief Solder Pads (See Note2) .025 - .035 [0.64] - [0.89] 810 Series Dimension E (Min) None .215 [5.46] Long .650 [16.51] Short .525 [13.34] .045 - .060 [1.14] - [1.52] *Solder Thief Solder Pads required only on Solder side of PC Board. View A D .002 E .160 Min [4.06] 2X .205 .003 [5.21] .050 .003 [1.27] .050 .002 Typ [1.27] Tolerance Noncumulative .100 .002 [2.54] Flow Solder Direction VIEW A View A 2X .109 .002 [2.77] .225 Min [5.72] .100 .002 [2.54] .025 .003 Typ [0.64] Recommended Mounting Hole Pattern PTH Vertical Header Inch [Imm] (shown for mounting side of PC Board) Tolerance Unless Noted Inch Note: 1. Recommended to process PC Boards through the solder bath such that the connector enters end first (two solder tails at a time). This will help prevent solder bridging. 2. A Solder Thief Solder Pad (Dummy Pad) at the end of each row is recommended on the bottom or solder side of the PC Board in order to help prevent solder bridging on the end solder tails. The Solder Thiefs are only required on the end of the rows which leave the solder bath last. 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com .0 .00 .000 .1 .01 .005 [ ] Dimensions for Reference Only TS-0253-K Sheet 5 of 7 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM 4-Wall, Tripolarized Header .050" x .100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle 810 Series Table 7 C Contact Quantity A B 020 1.060 [26.92] 0.722 [18.34] 1.671 [42.44] 1.842 [46.79] WF 026 1.210 [30.73] 0.872 [22.15] 1.821 [46.25] 1.992 [50.60] WF 036 1.460 [37.08] 1.122 [28.50] 2.071 [2.60] 2.242 [56.95] WG 040 1.560 [39.62] 1.222 [31.04] 2.171 [55.14] 2.342 [59.49] WG 2.592 1.810 [37.39] [61.49] [65.84] WG 060 2.060 [52.32] 1.722 [43.74] 2.671 [67.84] 2.842 [72.19] WG 068 2.260 [57.40] 1.922 [48.82] 2.871 [72.92] 3.042 [77.27] WH 080 2.560 [65.02] 2.222 [56.44] 3.171 [80.54] 3.342 [84.89] WH 100 3.060 [77.72] 2.722 [69.14] 3.671 [93.24] 3.842 [97.59] WH D Long Latch .440 .010 [11.18] .015 [0.38] Optional Single Press Fit Post Mount/Alignment Feature .116 [2.95] .405 [10.29] Ejector/Latch System: 0 = None (Special Order) 5 = With Short Ejectors Installed (Special Order) 6 = With Long Ejector Latches Installed (Standard) 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com .265 [6.73] .05 Ref Contact Mating Point .346 .010 [8.79] .093 [2.36] Inch [Imm] Optional Metal Clip Retention Tolerance Unless Noted Notes: 1. This polarization bump does not exist on the 20 position header. 2. Recommended to be mated to the .050" X .100" 820 Series Wiremount Socket. Contact Quantity (See Table 7) .140 .010 [3.56] .828 Ref [21.03] .620 Ref [15.75] Ordering Information 2.421 Tape & Reel Suffix Notes: L atches supplied in the "open" position unless specified otherwise Suffix determined with no posts or clips. Addition of posts or clips may increase suffix. 120 mm (WH) is the maximum width of pocket tape. .165 .010 [4.19] .092 [2.34] 1.472 D Long (Ref.) [45.97] 050 Short Latch Position 1 Orientation Triangle Dimensions D Short (Ref.) Inch .00 .000 .01 .005 [ ] Dimensions for Reference Only SMT Straight Header Ejector Latches (If Ordered Separately) 81XXX - 6X0C0X - XX - XX Board Mounting Options: 1 = None 4 = Press Fit Post Mount at Position 1 end 7 = Metal retention clips 8 = #1 end press fit post & metal retention clips (Special Order) .0 .1 Packaging Options: Blank = Trays WX = Tape & Reel Package (see table) Long Latches 3505-28B (black) Short Latches 3505-29B (black) Plating suffix: blank = 125 " tin lead tails (RIA E3 & C2 apply) RB = 250 " matte tin tails (RIA E1 & C1 apply) TS-0253-K Sheet 6 of 7 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM 4-Wall, Tripolarized Header .050" x .100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle 810 Series Dimensions Ejector Latches .065 .002 Typ [1.65] H Min None .775 [19.69] Long 1.085 [27.56] Short 1.21 [30.73] .042 .003 Typ (Plated thru hole) [1.07] No. of Positions Typ, Full R Detail A Optional plated thru hole for metal clip retention Dimensions F G 20 .450 [11.43] N/A 26 .600 [15.24] .025 [0.64] 36 .850 [21.59] N/A 40 .950 [24.13] N/A 50 1.200 [30.48] .025 [.64] 60 1.450 [36.83] 0.000 68 1.650 [41.91] 0.000 80 1.950 [49.53] 0.000 100 2.450 [62.23] 0.000 C L F Optional Drilled Hole for Plastic Post .109 .002 [2.77] C L See Detail A .158 .002 [4.01] Position 2 .050 .002 Typ [1.27] Tolerance Noncumulative .029 .001 [0.74] 2X .075 .002 [1.905] C L G .220 .003 [5.59] .110 .002 [2.79] .376 [9.55] Position 1 C L H .280 [7.11] .205 .003 [5.21] Recommended Mounting Hole Pattern, SMT Straight Header (Shown for mounting side of PC Board) TS-0253-K Sheet 7 of 7 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3Mconnectors.com Please recycle. Printed in USA. (c) 3M 2012. All rights reserved. RIA-2217B-E 3M is a trademark of 3M Company. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: 3M: CHG-2064-001010-KCP CHG-2064-001010-KEP 81020-620201 81060-620201 81040-520203 C3667/34-100 C3667/20-100 81040-620201 81020-520203 81026-520203 81068-620201 81026-620201 81068-520203 81060520203 81080-520203 81036-520203 81080-620201 81100-620201 81100-520203 81036-620201 81060-620203 81026-620203 81080-620203 81100-M10203 81026-620203-RB 81060-620203-RB 81080-620203-RB 81100M10203-RB 81050-520203 81060-620303 81020-620C04 CHG-2004-001010-KCP 81100-660203RB 81026600C01-RB-WE 81068-600C07RB 81068-660C01-RB-WG