WM30AV53H - CARLO GAVAZZI - Datasheet.Live

Specifications are subject to change without notice WM30 96 DS 161213 1

• Class 0.5 (kWh) according to

EN62053-22

• Class C (kWh) according to EN50470-3

• Class 2 (kvarh) according to EN62053-23

• Accuracy ±0.2% RDG (current/voltage)

• Instantaneous variables readout: 4x4 DGT

• Energies readout: 9+1 DGT

• System variables: VLL, VLN, A, VA, W, var, PF, Hz,

Phase-sequence-asymmetry-loss.

• Single phase variables: VLL, VLN, AL, An (calculated),

VA, W, var, PF

• Both system and single phase variables with average

and max calculation

• Harmonic analysis (FFT) up to the 32nd harmonic

(current and voltage)

• Energy measurements (imported/exported): total and

partial kWh and kvarh

• Energy measurements according to ANSI C12.20 CA

0.5, ANSI C12.1 (revenue grade)

• Run hours counter (8+2 DGT)

• Real time clock function

• Application adaptable display and programming

procedure (Easyprog function)

• Universal power supply: 18 to 60VAC/DC, 90 to

260AC/VDC

• Front dimensions: 96x96 mm

• Front protection degree: IP65, NEMA4X, NEMA12

Product Description

Three-phase smart power

analyzer with built-in advanced

configuration system and LCD

data displaying. Particularly

recommended for the

measurement of the main

electrical variables. WM30 is

based on a modular housing for

panel mounting with IP65 (front)

protection degree. Moreover, the

analyzer can be provided with

digital outputs that can be either

for pulse proportional to the

Energy Management

Smart Modular Power Analyzer

Type WM30 96

• One RS232 and RS485 port (on request)

• Communication protocol: MODBUS-RTU, iFIX SCADA

compatibility

• MODBUS TCP/IP Ethernet port (on request)

• BACnet-IP over Ethernet port (on request)

• BACnet MS/TP over RS485 (on request)

• Ethernet/IP port (on request)

• Up to 2 digital outputs (pulse, alarm, remote control)

(on request)

• Up to 4 freely configurable virtual alarms

• Up to 2 analogue outputs (+20mA, +10VDC) (on request)

active and reactive energy being

measured or/and for alarm

outputs. The instrument can be

equipped with the following

modules: RS485/RS232,

Ethernet, BACnet-IP or BACnet

MS/TP communication ports,

pulse and alarm outputs.

Parameters programming and

data reading can be easily

performed by means of

WM3040Soft.

Model

Range code

System

Power Supply

A Outputs

B Outputs

Communication

Option

How to order

WM30-96 AV5 3 H R2 A2 S1 XX

Type Selection

Range codes

AV4: 400/690VLL AC

1(2)A

VLN: 160V to 480VLN

VLL: 277V to 830VLL

AV5: 400/690VLL AC

5(6)A

VLN: 160V to 480VLN

VLL: 277V to 830VLL

AV6: 100/208VLL AC

5(6)A

VLN: 40V to 144VLN

VLL: 70V to 250VLL

AV7: 100/208VLL AC

1(2)A

VLN: 40V to 144VLN

VLL: 70V to 250VLL

Options

XX: none

System

3: balanced and

unbalanced load:

3-phase, 4-wire;

3-phase, 3-wire;

2-phase, 3-wire;

1-phase, 2-wire

A Outputs

XX: none

O2: Dual channel static

output

R2: Dual channel relay

output

Power supply

H: 90 to 260V AC/DC

(48 to 62Hz)

L: 18 to 60VAC/DC

(48 to 62Hz)

B Outputs

XX: none

A2: Dual channel 20mA

DC output

V2: Dual channel 10V

DC output

Communication

XX: none

S1: RS485/RS232 port

E2: Ethernet / Internet

port

B1: BACnet (IP) over

Ethernet

B3: BACnet (MS/TP)

over RS485

E6: Ethernet/IP port

2Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

Position of modules and combination

NOTE:

(1) Only one A type module per meter in a maximum

combination of 3 total mixed modules on the same meter.

(2) Only one B type module per meter in a maximum

combination of 3 total mixed modules on the same meter.

(3) Only one C type module per meter in a maximum

combination of 3 total mixed modules on the same meter.

The B-C position is not mandatory, if to fulfil the application,

module “A” is not necessary, just “B” can be mounted.

Another example: if modules “A” and “B” (anyone) are not

needed, then just module “C” maybe be mounted. If “A”

module is needed, it is mandatory to put it in “A” position.

When no modules are mounted, then WM30-96 becomes a

simple indicator.

ABC

Ref Description Main features Part number Pos. A Pos. B Pos. C

WM30 base provided with display,

power supply, measuring inputs

• Inputs/system: AV5.3

• Power supply: H WM30 AV5 3 H

2• Inputs/system: AV6.3

• Power supply: H WM30 AV6 3 H

3• Inputs/system: AV5.3

• Power supply: L WM30 AV5 3 L

4• Inputs/system: AV6.3

• Power supply: L WM30 AV6 3 L

5 Dual relay output (SPDT) • 2-channel

• Alarm or/and pulse output M O R2 (1) X

6 Dual static output (AC/DC Opto-Mos) • 2-channel

• Alarm or/and pulse output M O O2 (1) X

7 Dual analogue output (+20mADC) • 2-channel M O A2 (2) X

8 Dual analogue output (+10VDC) • 2-channel M O V2 (2) X

9 RS485 / RS232 port module • Max. 115.2 Kbps M C 485 232 (3) X

10 Ethernet port module • RJ45 10/100 BaseT M C ETH (3) X

11 BACnet-IP port module • Based on Ethernet bus M C BAC IP (3) X

12 BACnet-MS/TP port module • Over RS485 M C BAC MS (3) X

13 Ethernet/IP • Based on Ethernet M C E I (3) X

Specifications are subject to change without notice WM30 96 DS 161213 3

WM30 96

Rated inputs System type: 1, 2 or 3-

phase

Input type Galvanic insulation by

means of built-in CT’s

Current range (by CT) AV5 and AV6: 5(6)A

AV4 and AV7: 1(2)A

Voltage (by direct connection

or VT/PT) AV4, AV5: 400/690VLL;

AV6, AV7: 100/208VLL

Accuracy (Display + RS485)

(@25°C ±5°C, R.H.

≤60%, 45 to 65 Hz) In: see below, Un: see

below

AV4 model In: 1A, Imax: 2A; Un: 160

to 480VLN (277 to 830VLL)

AV5 model In: 5A, Imax: 6A; Un: 160

to 480VLN (277 to 830VLL)

AV6 model In: 5A, Imax: 6A; Un: 40 to

144VLN (70 to 250VLL)

AV7 model In: 1A, Imax: 2A; Un: 40 to

144VLN (70 to 250VLL)

Current AV4, AV5, AV6,

AV7 models From 0.01In to 0.05In:

±(0.5% RDG +2DGT)

From 0.05In to Imax:

±(0.2% RDG +2DGT)

Phase-neutral voltage In the range Un: ±(0,2%

RDG +1DGT)

Phase-phase voltage In the range Un: ±(0.5%

RDG +1DGT)

Frequency ±0.01Hz (45 to 65Hz)

Active and Apparent power 0.01In to 0.05In, PF 1:

±(1%RDG+1DGT)

From 0.05In to Imax

PF 0.5L, PF1, PF0.8C:

±(0.5%RDG+1DGT)

Power Factor ±[0.001+0.5% (1.000 - “PF

RDG”)]

Reactive power 0.02In to 0.05In, senφ1:

±(1.5%RDG+1DGT)

0.05In to Imax, senφ1:

±(1%RDG+1DGT)

0.05In to 0.1In, senφ

0.5L/C:

±(1.5%RDG+1DGT)

0.1In to Imax, senφ0.5L/C:

±(1%RDG+1DGT)

Active energy Class 0.5 according to

EN62053-22, ANSI C12.20

Class C according to

EN50470-3.

Reactive energy Class 2 according to

EN62053-23, ANSI C12.1.

Start up current AV5, AV6 5mA

Start up current AV4, AV7 1mA

Energy additional errors According to EN62053-22,

ANSI C12.20,

Influence quantities Class B or C according to

EN50470-3, EN62053-23,

ANSI C12.1

Total Harmonic Distortion (THD) ±1% FS (FS: 100%)

AV4: Imin: 5mARMS;

Imax: 3A; Umin: 30VRMS;

Umax: 679V

AV5: Imin: 5mARMS; Imax:

15Ap; Umin: 30VRMS;

Umax: 679V

AV6: Imin: 5mARMS; Imax:

15Ap; Umin: 30VRMS;

Umax: 204V

AV7: Imin: 5mARMS; Imax:

3A; Umin: 30VRMS; Umax:

204V

Temperature drift ≤200ppm/°C

Sampling rate 3200 samples/s @ 50Hz,

3840 samples/s @ 60Hz

Measurements See “List of the variables

that can be connected to:”

Method TRMS measurements of

distorted wave forms.

Coupling type By means of CT’s

Crest factor AV5, AV6: ≤3 (15A max.

peak)

AV4, AV7: ≤3 (3A max.

peak)

Current Overloads

Continuous (AV5 and AV6) 6A, @ 50Hz

Continuous (AV4 and AV7) 2A, @ 50Hz

For 500ms (AV5 and AV6) 120A, @ 50Hz

For 500ms (AV4 and AV7) 40A, @ 50Hz

Voltage Overloads

Continuous 1.2 Un

For 500ms 2 Un

Input impedance

400VL-L (AV4 and AV5) > 1.6MΩ

208VL-L (AV6 and AV7) > 1.6MΩ

5(6)A (AV5 and AV6) < 0.2VA

1(2)A (AV4 and AV7) < 0.2VA

Frequency 40 to 440 Hz

Input specifications

4Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

Relay outputs (M O R2)

Physical outputs 2 (max. 1 module per

instrument)

Purpose For either alarm output or

pulse output

Type Relay, SPDT type

AC 1-5A @ 250VAC; AC

15-1.5A @ 250VAC

DC 12-5A @ 24VDC; DC

13-1.5A @ 24VDC

Configuration By means of the front key-

pad

Function The outputs can work as

alarm outputs but also as

pulse outputs, remote

controlled outputs, or in

any other combination.

Alarms Up alarm and down alarm

linked to the virtual alarms,

other details see Virtual

alarms

Min. response time ≤200ms, filters excluded.

Set-point on-time delay: “0 s”.

Pulse

Signal retransmission Total: +kWh, -kWh, +kvarh,

-kvarh.

Partial: +kWh, -kWh,

+kvarh, -kvarh.

Pulse type The above listed variables

can be connected to any

output. Programmable

from 0.001 to 10.00

kWh/kvarh per pulse.

Pulse duration ≥100ms <120msec (ON),

≥120ms (OFF), according

to EN62052-31

Remote controlled

outputs The activation of the

outputs is managed

through the serial

communication port

Insulation See “Insulation between

inputs and outputs” table

Static outputs (M O O2) Opto-Mos type

Physical outputs 2 (max. 1 module per

instrument)

Purpose For either pulse output or

alarm output

Signal VON:2.5VAC/DC/max.100mA

VOFF: 260VAC/DC max.

Configuration By means of the front key-

pad

Function The outputs can work as

alarm outputs but also as

pulse outputs, remote

controlled outputs, or in

any other combination.

Alarms Up alarm and down alarm

linked to the virtual alarms,

other details see Virtual

alarms

Min. response time ≤200ms, filters excluded.

Set-point on-time delay: “0

s”.

Pulse

Signal retransmission Total: +kWh, -kWh, +kvarh,

-kvarh.

Partial: +kWh, -kWh,

+kvarh, -kvarh.

Pulse type The above listed variables

can be connected to any

output. Programmable

from 0.001 to 10.00

kWh/kvarh per pulse.

Pulse duration ≥100ms < 120msec (ON),

≥120ms (OFF), according

to EN62052-31

Remote controlled outputs The activation of the

outputs is managed

through the serial

communication port

Insulation See “Insulation between

inputs and outputs” table

20mA analogue outputs

(M O A2)

Number of outputs 2 (max. 1 module per

instrument)

Accuracy

(@ 25°C ±5°C, R.H. ≤60%) ±0.2%FS

Range 0 to 20mA

Configuration By means of the front key-

pad

Signal retransmission The signal output can be

connected to any

instantaneous variable

available in the table “List

of the variables that can be

connected to”.

Scaling factor Programmable within the

whole range of

retransmission.

Response time ≤400 ms typical (filter

excluded)

Ripple ≤1% (according to IEC

60688-1, EN 60688-1)

Total temperature drift ≤500 ppm/°C

Load ≤600Ω

Insulation See “Insulation between

inputs and outputs” table

10VDC analogue outputs

(M O V2)

Number of outputs 2 (max. 1 module per

instrument)

Accuracy

(@ 25°C ±5°C, R.H.  60%) ±0.2%FS

Range 0 to 10 VDC

Configuration By means of the front key-

pad

Signal retransmission The signal output can be

connected to any

instantaneous variable

available in the table “List

of the variables that can be

connected to”.

Scaling factor Programmable within the

whole range of

retransmission;

Response time ≤400 ms typical (filter

excluded)

Ripple ≤1% (according to IEC

60688, EN 60688)

Total temperature drift ≤500 ppm/°C

Load ≥10kΩ

Insulation See “Insulation between

inputs and outputs” table

Output specifications

Specifications are subject to change without notice WM30 96 DS 161213 5

WM30 96

RS485 (on request)

Type Multidrop, bidirectional

(static and dynamic

variables)

Connections 2-wire

Max. distance 1000m,

termination directly on the

module

Addresses 247, selectable by means

of the front key-pad

Protocol MODBUS/JBUS (RTU)

Data (bidirectional)

Dynamic (reading only) System and phase

variables: see table “List of

variables...”

Static (reading and writing only) All the configuration

parameters.

Data format 1 start bit, 8 data bit,

no/even/odd parity,1 stop bit

Baud-rate Selectable: 9.6k, 19.2k,

38.4k, 115.2k bit/s

Driver input capability 1/5 unit load. Maximum

160 transceivers on the

same bus.

Note With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation See “Insulation between

inputs and outputs” table

RS232 port (on request)

Type Bidirectional (static and

dynamic variables)

Connections 3 wires. Max. distance

15m

Protocol MODBUS RTU /JBUS

Data (bidirectional)

Dynamic (reading only) System and phase

variables: see table “List of

variables...”

Static (reading and writing only) All the configuration

parameters

Data format 1 start bit, 8 data bit,

no/even/odd parity,1 stop

bit

Baud-rate Selectable: 9.6k, 19.2k,

38.4k, 115.2k bit/s

Note With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation See “Insulation between

inputs and outputs” table

Ethernet/Internet port

(on request)

Protocols Modbus TCP/IP

IP configuration Static IP / Netmask /

Default gateway

Port Selectable (default 502)

Client connections Max 5 simultaneously

Connections RJ45 10/100 BaseTX

Max. distance 100m

Data (bidirectional)

Dynamic (reading only) System and phase

variables: see table “List of

variables...”

Static (reading and

writing only) All the configuration

parameters.

Note With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation See “Insulation between

inputs and outputs” table

BACnet-IP

(on request)

Protocols BACnet-IP (for

measurement reading

purpose) and Modbus

TCP/IP (for measurement

reading purpose and for

programming parameter

purpose)

Device object instance 0 to 9999 selectable by

key-pad

0 to 2^22-2 = 4.194.302,

selectable by programming

software or by BACnet.

Protocol BACnet MS/TP (for

measurement reading

purpose and to write

object description)

Supported services “I have”, “I am”, “Who

has”, “Who is”, “Read

(multiple) Property”

Supported objects Type 2 (analogue value,

including COV property),

Type 5 (binary-value for up

to 16 virtual alarm re-

transmission)

Type 8 (device)

IP configuration Static IP / Netmask /

Default gateway

BACnet-IP Port Fixed: BAC0h

Modbus Port Selectable (default 502)

Client connections Modbus only: max 5

simultaneously

Connections RJ45 10/100 BaseTX

Max. distance 100m

Data

Dynamic (reading only) System and phase

variables (BACnet-IP and

Output specifications (cont.)

6Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

Modbus): see table “List of

variables...”

Static (reading and

writing only) All the configuration

parameters (Modbus only).

Note With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation See “Insulation between

inputs and outputs” table

BACnet MS/TP (on request)

Available ports 2: RS485 and Ethernet

RS485 port

Type Multidrop, mono-

directional (dynamic

variables)

Connections 2-wire Max. distance

1000m, termination directly

on the module

Device object instance 0 to 9999 selectable by

key-pad

0 to 2^22-2 = 4.194.302,

selectable by programming

software or by BACnet.

Protocol BACnet MS/TP (for

measurement reading

purpose and to write

object description)

Supported services “I have”, “I am”, “Who

has”, “Who is”, “Read

(multiple) Property”

Supported objects Type 2 (analogue value,

including COV property),

Type 5 (binary-value for up

to 16 virtual alarm re-

transmission)

Type 8 (device)

Data (mono-directional)

Dynamic System and phase

variables: see table “List of

variables...”

Static Not available

Data format 1 start bit, 8 data bit, no

parity,1 stop bit

Baud-rate Selectable: 9.6k, 19.2k,

38.4k or 76.8k kbit/s

Driver input capability 1/5 unit load. Maximum

160 transceivers on the

same bus.

MAC addresses Selectable: 0 to 127

Ethernet port

Protocol Modbus TCP/IP (for

programming parameter

purpose)

IP configuration Static IP / Netmask /

Default gateway

Modbus Port Selectable (default 502)

Client connections Modbus only: max 5

simultaneously

Connections RJ45 10/100 BaseTX Max.

distance 100m

Data

Dynamic (reading only) System and phase

variables: see table “List of

variables...”

Static (reading and

writing only) All the configuration

parameters (Modbus only).

Note With the rotary switch (on

the back of the basic unit)

in lock position the

modification of the

programming parameters

and the reset command by

means of the serial

communication is not

allowed anymore. In this

case just the data reading

is allowed.

Insulation See “Insulation between

inputs and outputs” table

Ethernet/IP (on request)

Protocols Ethernet/IP (for

measurement reading

purpose) and Modbus

TCP/IP (for programming

parameter purpose)

IP configuration Static IP / Netmask /

Default gateway

Modbus Port Selectable (default 502)

Modbus only: max 5

simultaneously RJ45

10/100 Base TX

Max distance 100m

Ethernet/IP port

Topology Star

RJ45 standard

Max distance 100m

Level Commercial level

Connection Connection establishment:

target

Messanging Class 1 and class 3

messanging

Supported features ACD (Address Conflict

Detection)

UCMM

List service 0x0004

List identity 0x0063

Unregister session 0x0066

Send RR data 0x006F

Send Unit Data 0x0070

Data

Dynamic (reading only) System and phase

variables (Ethernet/IP): see

Ethernet/IP protocol

document

Static (reading and writing

only) All the configuration

parameters (Modbus TCP

only)

Insulation See “Insulation between

inputs and outputs” table

Output specifications (cont.)

Specifications are subject to change without notice WM30 96 DS 161213 7

WM30 96

Min. -9,999,999,999

kWh/kvarh

Max. 9,999,999,999

kWh/kvarh.

Energy Meters

Total energy meters +kWh, +kvarh, -kWh,

-kvarh

Partial energy meters +kWh, +kvarh, -kWh,

-kvarh

Meters

Total 4 (9+1 digit)

Partial 4 (9+1 digit)

Pulse output Connectable to total

and/or partial meters

Energy meter recording Storage of total and partial

energy meters.

Energy meter storage

format (EEPROM)

Energy meters

The same for the other

phases: L2, L3.

System The harmonic distortion

can be measured in 3-wire

or 4-wire systems.

Tw: 0.02 sec@50Hz

without filter

Analysis principle FFT

Harmonic measurement

Current Up to the 32nd harmonic

Voltage Up to the 32nd harmonic

Type of harmonics THD (VL1 and VL1-N)

The same for the other

phases: L2, L3.

THD (AL1)

Harmonic distortion analysis

kWh pulsating 0.001 kWh/kvarh by pulse

if the Ct ratio by VT ratio is

≤7

0.01 kWh/kvarh by pulse if

the Ct ratio by VT ratio is

≥7.1 ≤70.0

0.1 kWh/kvarh by pulse if

the Ct ratio by VT ratio is

≥70.1 ≤700.0

1 kWh/kvarh by pulse if

the Ct ratio by VT ratio is

≥700.1 ≤7000

10 kWh/kvarh by pulse if

the Ct ratio by VT ratio is

≥7001 ≤70.00k

100 kWh/kvarh by pulse if

the Ct ratio by VT ratio is

>70.01k

Max frequency: 16Hz,

according to EN50470-1

Back position LEDs

On the base Green as power-on

On the communication modules Two LEDs: one for TX

(green) and one for RX

(amber).

Key-pad For variable selection,

programming of the

instrument working

parameters, “dmd”, “max”,

total energy and partial

energy Reset

Display refresh time ≤250 ms

Display 4 lines, 4-DGT, 1 lines,

10-DGT

Type LCD, single colour

backlight

Digit dimensions 4-DGT: h 9.5mm; 10-DGT:

h 6.0mm

Instantaneous variables read-out 4-DGT

Energies variables read-out Imported Total/Partial:

9+1DGT or 10DGT;

Exported Total/Partial:

9+1DGT or 10DGT (with “-

“ sign).

Run Hours counter 8+2 DGT (99.999.999

hours and 59 minutes max)

Overload status EEEE indication when the

value being measured is

exceeding the “Continuous

inputs overload”

(maximum measurement

capacity)

Max. and Min. indication Max. instantaneous

variables: 9999; energies:

9 999 999 999. Min.

instantaneous variables:

0.000; energies 0.0

Front position LEDs

Virtual alarms 4 red LED available in case

of virtual alarm (AL1-AL2-

AL3-AL4). Note: the real

alarm is just the activation

of the proper static or relay

output if the proper

module is available.

Energy consumption Red LED (only kWh)

Display, LEDÊs and commands

8Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

programmable from 0

(always on) to 255 minutes

Virtual alarms

Working condition In case of basic unit or

with the addition of M O

R2 or M O O2 digital

output modules.

No. of alarms Up to 4

Working mode Up alarm and down alarm.

Controlled variables The alarms can be

connected to any

instantaneous variable

available in the table “List

of the variables that can be

connected to”.

Set-point adjustment From 0 to 100% of the

display scale

Hysteresis From 0 to 100% of the

display scale

On-time delay 0 to 255s

Min. response time ≤200ms, filters excluded.

Set-point on-time delay:

“0 s”.

Reset By means of the front key-

pad. It is possible to reset

the following data:

- all the max and dmd

values.

- total energies: kWh,

kvarh;

- partial energies: kWh,

kvarh

Harmonic analysis Up to the 32nd harmonics

on current and voltage

Clock

Functions Universal clock and calendar.

Time format Hour: minutes: seconds

with selectable 24 hours or

12H AM/PM format.

Date format Day-month-year with

selectable DD-MM-YY or

MM-DD-YY format.

Battery life 10 years

Easy programming function For all the display

selections, both energy

and power measurements

are independent from the

current direction. The

displayed energy is always

“imported” with the only

exception of “D”, “F” and

“G” types (see “display

pages” table). For those

latter selections the

energies can be either

“imported” or “exported”

depending on the current

direction.

Password Numeric code of max. 4

digits; 2 protection levels

of the programming data:

1st level Password “0”, no

protection;

2nd level Password from 1 to 9999,

all data are protected

System selection

System 3-Ph.n unbalanced load 3-phase (4-wire)

System 3-Ph. unbalanced load 3-phase (3-wire), three

currents and 3-phase to

phase voltage

measurements, or in case

of Aaron connection two

currents (with special

wiring on screw terminals)

and 3-phase to phase

voltage measurements.

System 3-Ph.1 balanced load 3-phase (3-wire), one

current and 3-phase to

phase voltage

measurements

3-phase (4-wire), one

current and 3-phase to

neutral voltage

measurements.

System 3-Ph.2 balanced load 3-phase (2-wire), one

current and 1-phase (L1) to

neutral voltage

measurement.

System 2-Ph 2-phase (3-wire)

System 1-Ph 1-phase (2-wire)

Transformer ratio

VT (PT) 1.0 to 999.9 /

1000 to 9999.

CT 1.0 to 999.9 / 1000 to 9999

(up to 10kA in case of CT

with 1A secondary current

and up to 50kA in case of

CT with 5A secondary

current).

Filter

Operating range Selectable from 0 to 100%

of the input display scale

Filtering coefficient Selectable from 1 to 32

Filter action Measurements, analogue

signal retransmission,

serial communication

(fundamental variables: V,

A, W and their derived

ones).

Displaying

Number of variables Up to 5 variables per page.

See “Front view”. 7

different set of variables

available (see “Display

pages”) according to the

application being selected.

One page is freely

programmable as

combination of variables.

Backlight The backlight time is

Main functions

Specifications are subject to change without notice WM30 96 DS 161213 9

WM30 96

Standard compliance

Safety IEC60664, IEC61010-1

EN60664, EN61010-1

EN62052-11.

Metrology EN62053-22, EN62053-23,

EN50470-3.

Pulse output DIN43864, IEC62053-31

Approvals Eligible System

performance Meter for Go

Solar California, CE, cULus

“Listed”

Connections Screw-type

Cable cross-section area max. 2.5 mm2.

min./max. screws

tightening torque: 0.4 Nm /

0.8 Nm.

Suggested screws

tightening torque: 0.5 Nm

Housing DIN

Dimensions (WxHxD) Module holder:

96x96x50mm.

“A” and “B” type modules:

89.5x63x16mm.

“C” type module:

89.5x63x20mm.

Max. depth behind the panel With 3 modules (A+B+C):

81.7 mm

Material ABS/Nylon PA66, self-

extinguishing: UL 94 V-0

Mounting Panel mounting

Protection degree

Front IP65, NEMA4x, NEMA12

Screw terminals IP20

Weight Approx. 400 g (packing

included)

Operating temperature -25°C to +55°C (-13°F to

131°F) (R.H. from 0 to 90%

non-condensing @ 40°C)

according to EN62053-21,

EN50470-1 and EN62053-

Storage temperature -30°C to +70°C (-22°F to

158°F) (R.H. < 90% non-

condensing @ 40°C)

according to EN62053-21,

EN50470-1 and EN62053-

Installation category Cat. III (IEC60664,

EN60664)

Insulation (for 1 minute) See “Insulation between

inputs and outputs” table

Dielectric strength 4kVAC RMS for 1 minute

Noise rejection CMRR 100 dB, 48 to 62 Hz

EMC According to EN62052-11

Electrostatic discharges 15kV air discharge

Immunity to irradiated Test with current: 10V/m

from 80 to 2000MHz

Electromagnetic fields Test without any current:

30V/m from 80 to 2000MHz

Burst On current and voltage

measuring inputs circuit:

4kV

Immunity to conducted

disturbances 10V/m from 150KHz to

80MHz

Surge On current and voltage

measuring inputs circuit:

4kV; on “L” auxiliary power

supply input: 1kV

Radio frequency suppression According to CISPR 22

General specifications

Insulation between inputs and outputs

(1): respect another module 4kV, in the same module 0kV.

-: combination not allowed.

NOTE: all the models have, mandatory, to be connected to external current transformers because the isolation among the

current inputs is just functional (100VAC).

Power Supply

(H o L)

Mesuring

inputs

Relè output

(MOR2)

Static ouput

(MOO2) Serial port Ethernet port Analogue

outputs

Power Supply

(H o L) - 4kV 4kV 4kV 4kV 4kV 4kV

Mesuring inputs 4kV - 4kV 4kV 4kV 4kV 4kV

Relè output

(MOR2) 4kV 4kV 2kV - 4kV 4kV 4kV

Static ouput

(MOO2) 4kV 4kV - 2kV 4kV 4kV 4kV

Serial port 4kV 4kV 4kV 4kV - - 4kV

Ethernet port 4kV 4kV 4kV 4kV - - 4kV

Analogue outputs 4kV 4kV 4kV 4kV 4kV 4kV 4kV(1)

10 Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

No Variable 1-ph.

sys

2-ph.

sys

3-ph. 3/4-wire

balanced sys

3-ph. 2-wire

balanced sys

3-ph. 3-wire

unbal. sys

3-ph. 4-wire

unbal. sys Notes

1 VL-N sys O X X X # X sys= system= ∑

2 VL1 X X X X # X

3 VL2 O X X X # X

4 VL3 O O X X # X

5 VL-L sys O # X X X X sys= system= ∑

6 VL1-2 # X X X X X

7 VL2-3 # O X X X X

8 VL3-1 # O X X X X

9Asys O X O O X X

10 An # X O O O X

11 AL1 X X X X X X

12 AL2 O X X X X X

13 AL3 O O X X X X

14 VA sys X X X X X X sys= system= ∑

15 VA L1 X X X X # X

16 VA L2 O X X X # X

17 VA L3 O O X X # X

18 var sys X X X X X X sys= system= ∑

19 var L1 X X X X # X

20 var L2 O X X X # X

21 var L3 O O X X # X

22 W sys X X X X X X sys= system= ∑

23 WL1 X X X X # X

24 WL2 O X X X # X

25 WL3 O O X X # X

26 PF sys X X X X X X sys= system= ∑

27 PF L1 X X X X # X

28 PF L2 O X X X # X

29 PF L3 O O X X # X

30 Hz X X X X X X

31 Phase seq. O X X X X X

32 Asy VLL O O X X X X Asymmetry

33 Asy VLN O X # O # X Asymmetry

34 Run Hours X X X X X X

35 kWh (+) X X X X X X Total

36 kvarh (+) X X X X X X Total

37 kWh (+) X X X X X X Partial

38 kvarh (+) X X X X X X Partial

39 kWh (-) X X X X X X Total

40 kvarh (-) X X X X X X Total

41 kWh (-) X X X X X X Partial

42 kvarh (-) X X X X X X Partial

43 A L1 THD X X X X X X

44 A L2 THD O X X X X X

45 A L3 THD O O X X X X

46 V L1 THD X X X X O X

47 V L2 THD O X X X O X

48 V L3 THD O O X X O X

49 V L1-2 THD X X X X X X

50 V L2-3 THD O X X X X X

51 V L3-1 THD O O X X X X

List of the variables that can be connected to:

• Communication port (all listed variables)

• Analogue outputs (all variables with the only exclusion of “energies” and “run hour counter”

• Pulse outputs (only “energies”)

• Alarm outputs (“energies” , “hour counter” and “max” excluded)

(X) = available; (O) = not available (variable not available on the display); (#) Not available (the relevant page is not displayed)

Specifications are subject to change without notice WM30 96 DS 161213 11

WM30 96

Power consumption AC: 6 VA;

DC: 3.5 W

Auxiliary power supply H: 90 to 260VAC/DC;

L: 18 to 60VAC/DC (48 to

62Hz)

Power supply specifications

Description Notes

ACost allocation Imported energy metering

BCost control Imported and partial energy metering

CComplex cost allocation Imported/exported energy (total and partial)

DSolar Imported and exported energy metering with some basic

power analyzer function

EComplex cost and power analysis Imported/exported energy (total and partial) and power

analysis

FCost and power quality analysis Imported energy and power quality analysis

GAdvanced energy and power analysis for power generation Complete energy metering and power quality analysis

Var

Type No Line 1

Variable Type

Line 2

Variable Type

Line 3

Variable Type

Line 4

Variable Type

Line 5

Variable Type Note Applications

A B C D E F G

0Home page Programmable x x x x x x x

a 1 Total kWh (+) b, c, d b, c, d b, c, d b, c, d x x x x x x x

a 2 Total kvarh (+) b, c, d b, c, d b, c, d b, c, d x x x x x x x

a 3 Total kWh (-) b, c, d b, c, d b, c, d b, c, d x x x x

a 4 Total kvarh (-) b, c, d b, c, d b, c, d b, c, d x x x x

a 5 kWh (+) partial b, c, d b, c, d b, c, d b, c, d x x x x x

a 6 kvarh (+) part. b, c, d b, c, d b, c, d b, c, d x x x x x

a 7 kWh (-) partial b, c, d b, c, d b, c, d b, c, d x x x

a 8 kvarh (-) part. b, c, d b, c, d b, c, d b, c, d x x x

a 9 Run Hours

(99999999.99) b, c, d b, c, d b, c, d b, c, d x x x x x

b 10 a/Phase seq. VLN ∑VL1 VL2 VL3 (1) (2) x x x x

b 11 a/Phase seq. VLN ∑VL1-2 VL2-3 VL3-1 (1) (2) x x x x

b 12 a/Phase seq. An AL1 AL2 AL3 (1) (2) x x x x

b 13 a/Phase seq. Hz “ASY” VLL sys

(% asy)

VLL sys

(% asy) (1) (2) x x x x

b 14 a/Phase seq. A ∑AL1 AL2 AL3 (1) (2) x x x x

c 15 a/Phase seq. W ∑WL1 WL2 WL3 (1) (2) x x x x

c 16 a/Phase seq. var ∑var L1 var L2 var L3 (1) (2) x x x

c 17 a/Phase seq. PF ∑PF L1 PF L2 PF L3 (1) (2) x x x

c 18 a/Phase seq. VA ∑VA L1 VA L2 VA L3 (1) (2) x x x

d 19 a/Phase seq. THD V1 THD V2 THD V3 (1) (2) x x

d 20 a/Phase seq. THD V12 THD V23 THD V31 (1) (2) x x

d 21 a/Phase seq. THD A1 THD A2 THD A3 (1) (2) x x

Display pages

List of selectable applications

Note: the table refers to system 3P.n.

(1) Also maximum value storage (no EEPROM storage).

(2) Also average (dmd) value (no EEPROM storage).

12 Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

Function Rotary switch position Description

Unlok 1

All programming parameters are freely modifiable by means

of the front key-pad and by means of the communication

port.

Lock 7

The key-pad, as far as programming is concerned and the

data through the serial communication cannot be changed

(no writing into meter allowed). Data reading is allowed.

Back protection rotary switch

No Line 1 Line 2 Line 3 Line 4 Line 5 Note Applications

A B C D E F G

1Lot n. (text) xxxx Yr. (text) xx SYS (text) x (1/2/3) 1...60 (min) “dmd” x x x x x x x

Conn. xxx.x

(3ph.n/3ph/3ph./

3ph.2/1ph/2ph)

CT.rA (text) 1.0 … 99.99k PT.rA (text) 1.0...9999 x x x x x x x

3LED PULSE (text)

kWh

xxxx kWh per

pulse x x x x x x x

4PULSE out1

(text) kWh/kvarh

xxxx kWh/kvarh

per pulse +/- tot/PAr x x x x x x x

5PULSE out2

(text) kWh/kvarh

xxxx kWh/kvarh

per pulse +/- tot/PAr x x x x x x x

6Remote out out1 (text) on/oFF Out2 (text) on/oFF x x x x x x x

7Alarm 1 nE/nd None / out 1 /

out 2 Set 1 Set 2 (measurement) x x x x

8Alarm 2 nE/nd None / out 1 /

out 2 Set 1 Set 2 (measurement) x x x x

9Alarm 3 nE/nd None / out 1 /

out 2 Set 1 Set 2 (measurement) x x x x

10 Alarm 4 nE/nd None / out 1 /

out 2 Set 1 Set 2 (measurement) x x x x

11 Analogue 1 Hi:E 0.0 ... 9999 Hi.A 0.0 ... 100.0% x x x x

12 Analogue 2 Hi:E 0.0 ... 9999 Hi.A 0.0 ... 100.0% x x x x

13 COM port None / out 1 /

out 2 xxx (address) bdr (text) 9.6/19.2/

38.4/115.2 x x x x x x x

14 IP address XXX XXX XXX XXX x x x x x x x

Additional available information on the display

Specifications are subject to change without notice WM30 96 DS 161213 13

WM30 96

Accuracy (According to EN50470-3 and EN62053-23)

kWh, accuracy (RDG) depending on the current

Percentage error limits for class index C

6A (Imax)

2A (Imax)

6A (Imax)

2A (Imax)

5A (In)

1A (Iref)

5A (In)

1A (Iref)

0.25A (Itr)

0.05A (Itr)

0.25A (Itr)

0.05A (Itr)

0.05A (Imin)

0.01A (Imin)

Accuracy limits (Active energy)

Start-up current: 5mA (AV5-6), 1mA (AV4-7)

kvarh, accuracy (RDG) depending on the current

Error

Accuracy limits (Reactive energy)

Start-up current: 5mA (AV5-6), 1mA (AV4-7)

PF=1

PF=L0.5

or C0.8

6A (Imax)

2A (Imax)

6A (Imax)

2A (Imax)

5A (In)

1A (Ib)

5A (In)

1A (Ib)

0.25A

0.05A

0.5A

0.1A

0.02A

0.25A

0.05A

sinj=1

sinj=0.5

+0.5%

+1%

-0.5%

-1%

+2%

+2,5%

-2%

-2,5%

System variables

Equivalent three-phase voltage

Voltage asymmetry

Three-phase reactive power

Three-phase active power

Three-phase apparent power

Total harmonic distortion

Used calculation formulas

Phase variables

Instantaneous effective voltage

Instantaneous active power

Instantaneous power factor

Instantaneous effective current

Instantaneous apparent power

Instantaneous reactive power

Energy metering

Where:

i= considered phase (L1, L2 or L3)

P= active power; Q= reactive power;

t1, t2=starting and ending time points

of consumption recording; n= time

unit; t= time interval between two

successive power consumptions;

n1, n2= starting and ending discrete

time points of consumption recording

Three-phase power factor

(TPF)

LLL L

LL V

ASY )( minmax

LNLN

LN V

ASY )( minmax

WM3040Soft parameter progr. and var. reading software

Working mode Three different working

modes can be selected:

- management of local

RS232 (MODBUS);

- management of a local

RS485 network (MODBUS);

- managed via TCP port

WM3040Soft Multi-language software

(Italian, English, French,

German, Spanish) for vari-

able reading, instrument

calibration and parameters

programming.The program

runs under Windows

XP/Vista/7

14 Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

3-CT and 3-VT/PT connections

3-CT connection

3-ph, 4-wire, unbalanced load Fig. 4

3-ph, 4-wire, unbalanced load Fig. 3

3-CT and 2-VT/PT connections

3-ph, 3-wire, unbalanced load Fig. 6

2-CT and 2-VT/PT connections ARON

3-ph, 3-wire, unbalanced load Fig. 8

2-CT connections (ARON)

3-ph, 3-wire, unbalanced load Fig. 7

3-CT connection

3-ph, 3-wire, unbalanced load Fig. 5

System type selection: 3-Ph

L2 L3 N S1 S2 S1 S2 S1 S2

I1 I2 I3

Wiring diagrams

1-CT and 1-VT/PT connections

1-CT connection

3-ph, 2-wire, balanced load Fig. 2

3-ph, 2-wire, balanced load Fig. 1

L1 N S1 S2

System type selection: 3-Ph.2

Power Supply

WM30 BACK-VIEW

L1 L2 L3 N S1 S2 S1 S2 S1 S2

I1 I2 I3

L1 L2 L3 N S1 S2 S1 S2 S1 S2

I1 I2 I3

L1 L2 L3 N S1 S2 S1 S2 S1 S2

I1 I2 I3

L1 L2 L3 N S1 S2 S1 S2 S1 S2

I1 I2 I3

L1 L2 L3 N S1 S2 S1 S2 S1 S2

I1 I2 I3

System type selection: 3-Ph.n

System type selection: 3-Ph (cont.)

Specifications are subject to change without notice WM30 96 DS 161213 15

WM30 96

Wiring diagrams

3-ph, 3-wire, balanced load Fig. 9

System type selection: 3-Ph.1

2-CT connection

2-ph, 3-wire Fig. 11

System type selection: 2-Ph

2-CT and 2-VT/PT connections

2-ph, 3-wire Fig. 12

1-CT connection

1-ph, 2-wire Fig. 13

System type selection: 1-Ph

1-CT and 2-VT/PT connections

3-ph, 3-wire, balanced load Fig. 10

1-CT and 1-VT/PT connections

1-ph, 2-wire Fig. 14

90 to 260VAC/DC (H option) Fig. 15 18 to 60VAC/DC (L option) Fig. 16

F= 250V [T] 630mA F= 250V [T] 3,15A

1212

Power Supply

L1 L2 L3 N S1 S2

I1 L1 L2 N S1 S2 S1 S2

I1 I2

L1 L2 N S1 S2 S1 S2

I1 I2

L1 N S1 S2

1-CT connections

System type selection: 2-Ph (cont.)

16 Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

RS485 and RS232 wiring diagrams

RS485 port

Static, relay and analogue outputs wiring diagrams

Relays

Analogue 20mA DC Analogue 10V DC

Out1 Out2 Out1 Out2

1234 1234

Opto-mosfet

RS232 port

NOTE. RS485: additional devices provided with RS485 are connected in parallel. The termination of the serial output is

carried out only on the last instrument of the network, by means of a jumper between (B+) and (T). : the communication

RS232 and RS485 ports can’t be connected and used simultaneously.

Out 1

234

Out 2

56 7

56781234

Out 1

Out 2

M O O2, M O R2, modules

M O A2, M O V2, modules

M C 485 232, module

Out1 Out2 Out1 Out2

Mandatory

termination

Specifications are subject to change without notice WM30 96 DS 161213 17

WM30 96

1. Key-pad

To program the configuration parameters and scroll the

variables on the display.

2. Display

LCD-type with alphanumeric indications to:

- display configuration parameters;

- display all the measured variables.

3. kWh LED

Red LED blinking proportional to the energy being

measured

4. Alarm LED’s

Red LED’s light-on when virtual alarms are activated.

5. Main bar-graph

To display the power consumption versus the

installed power.

Front panel description

RS485 wiring diagram of Bacnet module

RS485 port

NOTE. RS485: additional devices provided with RS485 are connected in parallel. The termination of the serial output is

carried out only on the last instrument of the network, by means of a jumper between (B+) and (T).

M C BAC MS, module

18 Specifications are subject to change without notice WM30 96 DS 161213

WM30 96

Dimensions and Panel cut-out