Instruction Sheet
408-8875
AMP NETCONNECT
Assembly Instructions for
LOC B
1
of 2
E
2007 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
27 NOV 07 Rev B
ETHERSEAL* Receptacle Kits
Toolless
Jack
Nut
O-Ring
Receptacle
Bend-Limiting Strain Relief
SL Series Jack
Shield
(With Shielded Kits Only)
In-Line Coupler
AMP-TWIST 6S Jack
PART NUMBER RECEPTACLE KIT DESCRIPTION
1479561-2 UTP, Cat 5e, Toolless Jack
1479562-2 Shielded, Cat 5e, Toolless Jack
1479563-2 UTP, Cat 5e, SL Series Jack
1479564-2 Shielded, Cat 5e, SL Series Jack
1479565-2 UTP, Cat 6, SL Series Jack
1479566-2 Shielded, Cat 6 SL Series Jack
1479567-2 Receptacle Only, No Jack
1479599-2 UTP, Cat 5e, In-Line Coupler
1479600-2 Shielded, Cat 5e, In-Line Coupler
1933589-2 AMP-TWIST 6S Jack
Figure 1
1. INTRODUCTION
This instruction sheet provides assembly procedures
for the receptacle kits listed in Figure 1.
To obtain information on AMP NETCONNECT products,
call PRODUCT INFORMATION at the number at the
bottom of this page, or visit the AMP NETCONNECT
website at
www.ampnetconnect.com
.
Dimensions are in millimeters [with inches in
brackets]. Figures are not drawn to scale.
2. DESCRIPTION
Each receptacle kit includes a receptacle, an O–ring,
a nut, and either a Toolless Jack Assembly, an
SL Series Jack Assembly, an In–Line Coupler, or an
NOTE
i
408-8875
Assembly Procedures for ETHERSEAL Receptacle Kits
Rev
B2
of 2 Tyco Electronics Corporation
AMP–TWIST 6S Jack. The shielded kits also include
a shield.
The jacks accept four–pair, twisted–pair cable with 22
to 24 AWG solid conductors and 24 AWG stranded
conductors. The maximum conductor insulation
diameter is 1.14 [.045] (Toolless jack) and 1.27 [.050]
(SL Series jack).
3. TERMINATION PROCEDURES
Refer to the instruction sheet listed in Figure 2 for
wire preparation and termination of each jack
assembly.
JACK ASSEMBLY DESCRIPTION INSTRUCTION SHEET
Unshielded Toolless Jack 408-4542
Shielded Toolless Jack 408-4588
Unshielded SL Series Jack 408-8417
Shielded SL Series Jack 408-8602
AMP-TWIST 6S Jack 411-93007
Figure 2
4. RECEPTACLE AND JACK INSTALLATION
The receptacle can be installed in a panel or a
faceplate cutout. Faceplates can be purchased
separately. Refer to Figure 3 for recommended panel
cutout dimensions.
Figure 3
25.65 [1.010]
28.45 [1.120]
Refer to Figure 4 and proceed as follows:
1. Slide O–ring over threaded portion of
receptacle.
2. Insert threaded portion of receptacle through
front of panel/faceplate cutout. Orient receptacle in
cutout so that white arrow indicator on front of
receptacle is facing up.
3. Attach nut (with 20–in–lb torque) to threaded
portion of receptacle at back of panel/faceplate.
4. Insert jack (or coupler) into back of receptacle
by aligning the fixed tab on the jack with the white
arrow indicator on the front of the receptacle. See
Figure 5.
5. Tilt the back of the jack (or coupler) up at a
slight angle and slide it into the opening in the
receptacle. Hook the fixed latch into the slot inside
the receptacle.
6. Rotate the back of the jack (or coupler) down.
The movable latch will deflect and lock into the
receptacle.
Figure 4
O-Ring
Receptacle
Faceplate
White Arrow Indicator
Nut
Figure 5
Fixed
Latch
White Arrow Indicator
(Ref - Front of Receptacle)
Insert Jack (or Coupler) at a
Slight Angle and Rotate UnĆ
til Movable Latch Snaps
Into Place
Movable
Latch
5. REVISION SUMMARY
Added AMP–TWIST 6S Jack and Cat 6 SL Series
Jack.
