Adjustable Recycle Time Delay
Relays (Flashers)
HDFA Series
Adjustable Recycle Timers
The HDFA Series low cost adjustable recycling
timers are packaged in the familiar hockey-puck
enclosure and may be used to alternately switch
power to two independent loads. Both OFF and ON
times are independently adjustable by means of
built-in potentiometers. Load power is controlled by
an isolated SPDT relay contact. Timing ranges are
adjustable of a 100:1 span and cover 0.25 seconds
to 100 minutes. Contact Rating: 10 amperes
maximum @ 250 VAC or 30 VDC. Operating
Temperature Range: Ð40¡C to 65¡C. Mounting:
Single center hole mount. Timing Cycle Interrupt
Transfer: None. UL and CSA approval pending.
Stock Mfr.Õs Recycle Input Mode of EACH
No. Type Delay Voltage Operation*
892-2012 120AA/AHDFA .25-10 sec. 120 VAC SPDT 40.49
892-2013 120AC/CHDFA .6-60 sec. 120 VAC SPDT 40.49
892-2014 120AF/FHDFA 1-100 min. 120 VAC SPDT 40.49
892-2015 12DA/AHDFA .25-10 sec. 12 VDC SPDT 40.49
892-2016 12DC/CHDFA .6-60 sec. 12 VDC SPDT 40.49
892-2017 12DF/FHDFA 1-100 min. 12 VDC SPDT 40.49
892-2018 24DA/AHDFA .25-10 sec. 24 VDC SPDT 40.49
892-2019 24DC/CHDFA .6-60 sec. 24 VDC SPDT 40.49
892-2020 24DF/FHDFA 1-100 min. 24 VDC SPDT 40.49
*SPDT = Single pole double throw contacts.
Amperite
Time Delay Relays and Flashers
For Fast, Dependable Service, Make Just One Call Ñ 1-800-433-5700 ALLIED
c
105
Delay on Release TDRs
CR Series TDR
The CR Series has solid state analog circuitry with SPDT
relay output. Triggered delay on release timing mode.
Compact size. Timing Selection: Knob adjustable
potentiometer or fixed. UL file #E96739(M). CSA File
#LR62586. Contact Rating: 1/2 amp @ 110-120 VAC,
1 amp @ 32 VDC. Operating Temperature Range: Ð25¡C
to +60¡C. Mounting: Single screw or optional 2-screw panel mount.
Stock Mfr.Õs Delay in Input Mode of EACH
No. Type Seconds Voltage Operation*
892-0063 115ASPDTR1-120C 1-120 115 VAC SPDT 31.89
892-0066 12DNOR1-120C 1-120 12 VDC N.O. 28.97
892-0067 12DSPDTR1-120C 1-120 12 VDC SPDT 31.89
892-0069 24ASPDTR1-120C 1-120 24 VAC SPDT 31.89
892-0071 24DSPDTR1-120C 1-120 24 VDC SPDT 32.71
*N.C. = Normally closed contacts, N.O. = Normally open contacts, SPDT =
Single pole double throw contacts.
CR10 Series (Low Cost 10 Amp TDR)
The CR10 Series has solid state analog circuitry with DPDT
relay output. Triggered delay on release timing mode. Timing
Selection: Knob adjustable potentiometer or fixed. UL
file #E96739(M). CSA File #LR62586-3. Contact Rating:
10 amps @ 240 VAC res. Operating Temperature Range:
Ð45¡C to +70¡C. Mounting: 11-pin octal style plug. Spade
terminal style available.
Stock Mfr.Õs Delay in Input EACH
No. Type Seconds Voltage
892-0077 120APR1-120C 1-120 120 VAC 49.71
892-0080 12DPR120-240C 120-240 12 VDC 49.71
892-0081 12DPR1-120C 1-120 12 VDC 46.73
892-0084 24DPR120-240C 120-240 24 VDC 46.73
892-0085 24DPR1-120C 1-120 24 VDC 46.73
Note: New Amperite products are continuously available. Call Allied for
availability and for information on custom termination, voltages and timing, as
well as accessories.
DCR10 Series Delay On
Release TDR
The DCR10 has CMOS digital circuitry with DPDT relay
output. Delay on Release timing mode. Timing Selection:
Knob adjustable potentiometer or fixed. UL File #E96739(M).
CSA File #LR62586. Contact Rating: 10 A at 240 V AC res.
Operating Temperature Range: Ð45¡C-+70¡C. Mounting:
11-pin octal style plug. Spade terminal style available.
Stock Mfr.Õs Delay Voltage EACH
No. Type Time
892-1201 120AP.1-10SDCR10 .1-10 sec. 120 AC 62.53
892-1002 120AP1-60HDCR10 1-60 hrs. 120 AC 59.39
892-1003 12DP.1-10SDCR10 .1-10 sec. 12 DC 59.39
892-1005 24DP.1-10SDCR10 .1-10 sec. 24 DC 59.39
Triggered Delay-On-Release
Time Delay Relays
STB Series Delay-On-Release TDRs
The STB Series triggered delay-on-release time
delay relay has CMOS digital timing circuitry. Units
are 100% solid state with no moving parts to wear
out. The relay is packaged in the popular hockey
puck enclosure, epoxy sealed. Timing can be
factory fixed or adjustable by use of a user
supplied resistor or potentiometer. Contact Rating:
2 amp continuous load. Mounting: Single center
hole mount. Timing Tolerance: Fixed units ±10%.
Repeatability: ±2%. Timing Cycle Interrupt
Transfer: None. UL and CSA approval pending.
Stock Mfr.Õs Delay in Input Mode of EACH
No. Type Seconds Voltage Operation*
892-2000 120A.1-10SSTB .1-10 120 AC N.O. 24.94
892-2001 120A1-100SSTB 1-100 120 AC N.O. 24.94
892-2002 12D.1-10SSTB .1-10 12 DC N.O. 24.94
892-2003 12D1-100SSTB 1-100 12 DC N.O. 24.94
892-2004 24D.1-10SSTB .1-10 24 DC N.O. 24.94
892-2005 24D1-100SSTB 1-100 24 DC N.O. 24.94
*N.O. = Normally open contacts.
Flashers (Low Cost 10 Amp Flasher)
DF10 Series
The DF10 Series has solid state analog circuitry with DPDT relay output.
Recycle timer/flasher timing mode. Timing Selection: fixed flash rates. Duty
Cycle: 50% UL File #E96739(M).CSA File #LR62586. Contact Rating: 10 amps
@ 240 VAC res. Operating Temperature Range: Ð45¡C to +70¡C. Mounting:
8-pin octal style plug. Spade terminal style available.
Stock Mfr.Õs Flash Rate Input Mode of EACH
No. Type F.P.M. Voltage Operation
892-0117 120AF60DF10 60 120 VAC Flasher 44.82
892-0118 120AF90DF10 90 120 VAC Flasher 44.82
892-0121 12DF60DF10 60 12 VDC Flasher 44.82
892-0123 24AF60DF10 60 24 VAC Flasher 44.82
892-0125 24DF60DF10 60 24 VDC Flasher 44.82
D Series
The D Series are solid state analog flashing devices. No moving parts to wear
out. 2 amp rating. Output: AC units Ñ Triac; DC units Ñ transistor. Low cost-
compact size. 3 terminal configuration. No current leakage to load. Fixed flash
rates. Duty Cycle: 50%. UL File #E96739(M). CSA File #LR62586. Operating
Temperature Range: Ð23¡C to +60¡C. Mounting: Single screw or optional 2
screw panel mount.
892-0133 115AF60D 60 115 VAC Flasher 20.01
892-0134 115AF90D 90 115 VAC Flasher 20.01
892-0137 12DF30D 30 12 VDC Flasher 20.01
892-0138 12DF60D 60 12 VDC Flasher 20.01
892-0142 24DF60D 60 24 VDC Flasher 20.01
DF Series
DFA Series Adjustable Recycle Timer
Relay Accessories
For use with C10, CI, DC10, DF10, DFA, DFV, DOD, G, SWDC and SWPDC series.
892-9998. 8-PIN-SM. 8 pin surface mount socket...........................EACH 6.22
For use with CR10, CIR, DCR10 and SWUDC series.
892-9999. 11-PIN-SM. 11 pin surface mound socket .....................EACH 10.72
For use with B, BF, D, DF and Fixed C and CR series.
892-1000. PANEL MOUNT. Non-adjustable 2-screw bracket ..........EACH 1.24
For use with adjustable C and CR series.
892-1140. PMCR BRACK..................................................................EACH 1.24
The DF Series are totally encapsulated solid state analog flashing devices.
Universal Input: 24 V to 120 V AC or DC operation in one device. No moving
parts to wear out. 2 amp rating. Low cost Ñ compact size. 2 terminal
configuration Ñ easy connection to load. Fixed flash rates. Duty Cycle: 50%
UL File #D96739(M). CSA File #LR62586. Operating Temperature Range:
Ð23¡C to +60¡C. Mounting: Single screw or optional 2 screw panel mount.
892-0144 24-120F30DF 30 24-120 VAC/DC Flasher 18.93
892-0145 24-120F45DF 45 24-120 VAC/DC Flasher 18.93
892-0146 24-120F60DF 60 24-120 VAC/DC Flasher 18.93
892-0147 24-120F90DF 90 24-120 VAC/DC Flasher 18.93
DFS Series
The DFA has CMOS digital circuitry with DPDT relay output. Adjustable Recycle
timing mode. Timing Selection: Two knob adjustable potentiometers or fixed.
UL File No. E96739 (M). CSA File No. LR62586. Contact Rating: 10 A at 240 V
AC res. Operating Temperature Range: Ð45¡C to +70¡C. Mounting: 8-pin octal
style plug. Spade terminal style available.
Stock Mfr.Õs Delay Voltage EACH
No. Type Time
892-1009 120AA/ADFA .1-10 sec. 120 AC 60.83
892-1010 120AF/FDFA 1-100 min. 120 AC 60.83
892-1011 24DA/ADFA .1-10 sec. 24 DC 60.83
892-1012 12DF/FDFA 1-100 min. 12 DC 60.83
Stop-Alert Lamp Pulsator
Two terminal solid state vehicular lamp enhancement device. Timing Mode:
5 pulses per second @ 85% duty cycle. Power Rating: 60 W continuous,
120 W intermittent. Operating Temperature: Ð40¡C to +60¡C. Mounting:
Single screw or 2 hole panel mount adapter available.
Stock Mfr.Õs Flash Rate Input Power EACH
No. Type F.P.M. Voltage Rating
892-1139 STOP-ALERT 300 12 VDC 60 W 18.93
The DFS series are CMOS digital three terminal flashers that are packaged in
the familiar 2 ´2 ´
3
/
4
" hockey puck enclosure, epoxy sealed. Load Current
Ratings: 3 A and 12 A available. Flash Rate: Fixed and can be customer
specified over a range of 1 to 1,000 flashes per minute with a 50% duty cycle.
UL File #E96739(M). CSA File #LR62586. Operating Temperature: Ð23¡C to
+60¡C. Mounting: Center hole.
892-1127 DFS152-60* 60 120 VAC Flasher 34.13
892-1128 DFS152-90* 90 120 VAC Flasher 34.13
892-1129 DFS154-60 60 120 VAC Flasher 42.68
892-1130 DFS154-90 90 120 VAC Flasher 42.68
892-1131 DFS219-60* 60 12 VDC Flasher 34.13
892-1132 DFS219-90* 90 12 VDC Flasher 34.13
892-1133 DFS220-60 60 12 VDC Flasher 42.68
892-1134 DFS220-90 90 12 VDC Flasher 42.68
892-1135 DFS224-60* 60 24 VDC Flasher 34.13
892-1136 DFS224-90* 90 24 VDC Flasher 34.13
892-1137 DFS225-60 60 24 VDC Flasher 42.68
892-1138 DFS225-90 90 24 VDC Flasher 42.68
*3 A. 12 A.
DFV Series Adjustable
Flasher
The DFV has solid state analog circuitry with DPDT
relay output. Adjustable Flasher Circuitry. Flash Rate
Timing Selection: Knob adjustable potentiometer. UL
File No. E96739 (M). CSA File No. LR62586. Contact
Rating: 10 A at 240 V AC res. Operating Temperature
Range: Ð45¡C to +70¡C. Mounting: 8-pin octal style
plug. Spade terminal style available.
Stock Mfr.Õs Flash Rate Input EACH
No. Type F.P.M. Voltage
892-1016 120AF10-120DFV 10-120 120 AC 42.70
892-1017 24DF10-120DFV 10-120 24 DC 42.70
892-1018 12DF10-120DFV 10-120 12 DC 42.70
4
