REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
a
Precision Rail-to-Rail
Input and Output Operational Amplifiers
OP184/OP284/OP484
FEATURES
Single-Supply Operation
Wide Bandwidth: 4 MHz
Low Offset Voltage: 65 V
Unity-Gain Stable
High Slew Rate: 4.0 V/s
Low Noise: 3.9 nV/Hz
APPLICATIONS
Battery Powered Instrumentation
Power Supply Control and Protection
Telecom
DAC Output Amplifier
ADC Input Buffer
GENERAL DESCRIPTION
The OP184/OP284/OP484 are single, dual and quad single-
supply, 4 MHz bandwidth amplifiers featuring rail-to-rail
inputs and outputs. They are guaranteed to operate from 3 to
36 (or ±1.5 to ±18) volts and will function with a single supply
as low as 1.5 volts.
These amplifiers are superb for single-supply applications
requiring both ac and precision dc performance. The combina-
tion of bandwidth, low noise and precision makes the OP184/
OP284/OP484 useful in a wide variety of applications, including
filters and instrumentation.
Other applications for these amplifiers include portable telecom
equipment, power supply control and protection, and as amplifi-
ers or buffers for transducers with wide output ranges. Sensors
requiring a rail-to-rail input amplifier include Hall effect, piezo
electric, and resistive transducers.
The ability to swing rail-to-rail at both the input and output
enables designers to build multistage filters in single-supply
systems and to maintain high signal-to-noise ratios.
The OP184/OP284/OP484 are specified over the HOT extended
industrial (–40°C to +125°C) temperature range. The single
and dual are available in 8-lead plastic DIP plus SO surface
mount packages. The quad OP484 is available in 14-lead plastic
DIPs and 14-lead narrow-body SO packages.
PIN CONFIGURATIONS
8-Lead Epoxy DIP
(P Suffix)
8-Lead SO
(S Suffix)
1
2
3
4
8
7
6
5
OUT A
V+
NULL
NC
NULL
–IN A
+IN A
V–
OP184
NC = NO CONNECT
+
8-Lead Epoxy DIP
(P Suffix)
8-Lead SO
(S Suffix)
1
2
3
4
8
7
6
5
OP284
OUT B
–IN B
+IN B
V+
OUT A
–IN A
+IN A
V–
14-Lead Epoxy DIP
(P Suffix)
14-Lead Narrow-Body SO
(S Suffix)
14
13
12
11
10
9
8
1
2
3
4
5
6
7
OP484
OUT A
–IN A
+IN A
V+
+IN B
–IN B
OUT B
OUT D
–IN D
+IN D
V–
+IN C
–IN C
OUT C
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700 www.analog.com
Fax: 781/326-8703 © Analog Devices, Inc., 2002
OP184/OP284/OP484–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Parameter Symbol Conditions Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage “OP184/284E” Grade V
OS
(Note 1) 65 µV
–40°C T
A
+125°C165 µV
Offset Voltage “OP184/284F” Grade V
OS
125 µV
–40°C T
A
+125°C350 µV
Offset Voltage “OP484E” Grade V
OS
75 µV
–40°C T
A
+125°C175 µV
Offset Voltage “OP484F” Grade V
OS
150 µV
–40°C T
A
+125°C450 µV
Input Bias Current I
B
60 450 nA
–40°C T
A
+125°C600 nA
Input Offset Current I
OS
250nA
–40°C T
A
+125°C50nA
Input Voltage Range 05V
Common-Mode Rejection Ratio CMRR V
CM
= 0 V to 5 V 60 dB
Common-Mode Rejection Ratio CMRR V
CM
= 1.0 V to 4.0 V, –40°C T
A
+125°C86 dB
Large Signal Voltage Gain A
VO
R
L
= 2 k, 1 V V
O
4 V 50 240 V/mV
R
L
= 2 k, –40°C T
A
+125°C25 V/mV
Bias Current Drift I
B
/T150 pA/°C
OUTPUT CHARACTERISTICS
Output Voltage High V
OH
I
L
= 1.0 mA 4.85 V
Output Voltage Low V
OL
I
L
= 1.0 mA 125 mV
Output Current I
OUT
±6.5 mA
POWER SUPPLY
Power Supply Rejection Ratio PSRR V
S
= 2.0 V to 10 V, –40°C T
A
+125°C76 dB
Supply Current/Amplifier I
SY
V
O
= 2.5 V, –40°C T
A
+125°C1.45mA
Supply Voltage Range V
S
336V
DYNAMIC PERFORMANCE
Slew Rate SR R
L
= 2 k1.65 2.4 V/µs
Settling Time t
S
To 0.01%, 1.0 V Step 2.5 µs
Gain Bandwidth Product GBP 3.25 MHz
Phase Margin Øo 45 Degrees
NOISE PERFORMANCE
Voltage Noise e
N
p-p 0.1 Hz to 10 Hz 0.3 µV p-p
Voltage Noise Density e
N
f = 1 kHz 3.9 nV/Hz
Current Noise Density i
N
0.4 pA/Hz
NOTES
1
Input Offset Voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power.
Specifications subject to change without notice.
REV. B
–2–
(@ V
S
= 5.0 V, V
CM
= 2.5 V, T
A
= 25C unless otherwise noted.)
ELECTRICAL CHARACTERISTICS
Parameter Symbol Conditions Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage “OP184/284E” Grade V
OS
(Note 1) 65 µV
–40°C T
A
+125°C165 µV
Offset Voltage “OP184/284F” Grade V
OS
125 µV
–40°C T
A
+125°C350 µV
Offset Voltage “OP484E” Grade V
OS
100 µV
–40°C T
A
+125°C200 µV
Offset Voltage “OP484F” Grade V
OS
150 µV
–40°C T
A
+125°C450 µV
Input Bias Current I
B
60 450 nA
–40°C T
A
+125°C600 nA
Input Offset Current I
OS
–40°C T
A
+125°C50nA
Input Voltage Range 03V
Common-Mode Rejection Ratio CMRR V
CM
= 0 V to 3 V 60 dB
Common-Mode Rejection Ratio CMRR V
CM
= 0 V to 3 V, –40°C T
A
+125°C56 dB
OUTPUT CHARACTERISTICS
Output Voltage High V
OH
I
L
= 1.0 mA 2.85 V
Output Voltage Low V
OL
I
L
= 1.0 mA 125 mV
POWER SUPPLY
Power Supply Rejection Ratio PSRR V
S
= ±1.25 V to ±1.75 V 76 dB
Supply Current/Amplifier I
SY
V
O
= 1.5 V, –40°C T
A
+125°C1.35 mA
DYNAMIC PERFORMANCE
Gain Bandwidth Product GBP 3 MHz
NOISE PERFORMANCE
Voltage Noise Density e
N
f = 1 kHz 3.9 nV/Hz
NOTES
1
Input Offset Voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power.
Specifications subject to change without notice.
REV. B –3–
OP184/OP284/OP484
(@ V
S
= 3.0 V, V
CM
= 1.5 V, T
A
= 25C unless otherwise noted.)
REV. B
–4–
OP184/OP284/OP484
ELECTRICAL CHARACTERISTICS
Parameter Symbol Conditions Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage “OP184/284E” Grade V
OS
(Note 1) 100 µV
–40°C T
A
+125°C200 µV
Offset Voltage “OP284F” Grade V
OS
175 µV
–40°C T
A
+125°C375 µV
Offset Voltage “OP484E” Grade V
OS
150 µV
–40°C T
A
+125°C300 µV
Offset Voltage “OP484F” Grade V
OS
250 µV
–40°C T
A
+125°C500 µV
Input Bias Current I
B
80 450 nA
–40°C T
A
+125°C575 nA
Input Offset Current I
OS
–40°C T
A
+125°C50nA
Input Voltage Range –15 +15 V
Common-Mode Rejection Ratio CMRR V
CM
= –14.0 V to +14.0 V, –40°C T
A
+125°C86 90 dB
Common-Mode Rejection Ratio CMRR V
CM
= –15.0 V to +15.0 V 80 dB
Large-Signal Voltage Gain A
VO
R
L
= 2 k, –10 V V
O
10 V 150 1000 V/mV
R
L
= 2 k, –40°C T
A
+125°C75 V/mV
Offset Voltage Drift “E” Grade V
OS
/T0.2 2.00 µV/°C
Bias Current Drift I
B
/T150 pA/°C
OUTPUT CHARACTERISTICS
Output Voltage High V
OH
I
L
= 1.0 mA 14.8 V
Output Voltage Low V
OL
I
L
= 1.0 mA –14.875 V
Output Current I
OUT
±10 mA
POWER SUPPLY
Power Supply Rejection Ratio PSRR V
S
= ±2.0 V to ±18 V, –40°C T
A
+125°C90 dB
Supply Current/Amplifier I
SY
V
O
= 0 V, –40°C T
A
+125°C2.0 mA
Supply Current/Amplifier I
SY
V
S
= ±18 V, –40°C T
A
+125°C2.25mA
DYNAMIC PERFORMANCE
Slew Rate SR R
L
= 2 k2.4 4.0 V/µs
Full-Power Bandwidth BW
p
1% Distortion, R
L
= 2 k, V
O
= 29 V p-p 35 kHz
Settling Time t
S
To 0.01%, 10 V Step 4 µs
Gain Bandwidth Product GBP 4.25 MHz
Phase Margin Øo 50 Degrees
NOISE PERFORMANCE
Voltage Noise e
N
p-p 0.1 Hz to 10 Hz 0.3 µV p-p
Voltage Noise Density e
N
f = 1 kHz 3.9 nV/Hz
Current Noise Density i
N
0.4 pA/Hz
NOTES
1
Input Offset Voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power.
Specifications subject to change without notice.
(@ V
S
= 15.0 V, V
CM
= 0 V, T
A
= 25C unless otherwise noted.)
REV. B –5–
OP184/OP284/OP484
ABSOLUTE MAXIMUM RATINGS
1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Differential Input Voltage
2
. . . . . . . . . . . . . . . . . . . . . . ±0.6 V
Output Short-Circuit Duration to GND
3
. . . . . . . . Indefinite
Storage Temperature Range
P, S Packages . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range
OP184/OP284/OP484E, F . . . . . . . . . . . . –40°C to +125°C
Junction Temperature Range
P, S Packages . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . . 300°C
Package Type
JA3
JC
Unit
8-Lead Plastic DIP (P) 103 43 °C/W
8-Lead SOIC (S) 158 43 °C/W
14-Lead Plastic DIP (P) 83 39 °C/W
14-Lead SOIC (S) 92 27 °C/W
NOTES
1
Absolute maximum ratings apply to both DICE and packaged parts unless
otherwise noted.
2
For input voltages greater than 0.6 volts, the input current should be limited to less
than 5 mA to prevent degradation or destruction of the input devices.
3
θ
JA
is specified for the worst case conditions; i.e., θ
JA
is specified for device in socket
for cerdip and P-DIP packages; θ
JA
is specified for device soldered in circuit board
for SOIC package.
R3
Q1
–IN +IN
QL1
QL2
Q4
Q3 Q2
QB5
QB6
RB2
QB3
R1
Q5
R2
QB4
JB2
QB1
CB1 N+
P+M
QB2
CC1
Q9
Q7
Q11
Q8
Q6
Q10
Q12
QB7 QB8
QB9
RB1
JB1
TP
R4
R5
R6
RB3
CFF
R7
R8
Q13 Q14
R10
Q15
RB4
QB10
CC2
CO
Q17
Q16
R11
Q18
V
CC
OUT
V
EE
R9
Figure 3. Simplified Schematic
ORDERING GUIDE
Temperature Package Package
Model Range Description Option
OP184EP*–40°C to +125°C8-Lead Plastic DIP N-8
OP184ES –40°C to +125°C8-Lead SOIC R-8
OP184FP*–40°C to +125°C8-Lead Plastic DIP N-8
OP184FS –40°C to +125°C8-Lead SOIC R-8
OP284EP –40°C to +125°C8-Lead Plastic DIP N-8
OP284ES –40°C to +125°C8-Lead SOIC R-8
OP284FP
*
–40°C to +125°C8-Lead Plastic DIP N-8
OP284FS –40°C to +125°C8-Lead SOIC R-8
OP484ES –40°C to +125°C14-Lead SOIC R-14
OP484FP –40°C to +125°C14-Lead Plastic DIP N-14
OP484FS –40°C to +125°C14-Lead SOIC R-14
NOTES
*Not for new design; obsolete April 2002.
INPUT OFFSET VOLTAGE – V
QUANTITY
300
0
–100 –75 100–50 –25 0 25 50 75
270
180
90
60
30
240
210
120
150
V
S
= 3V
T
A
= 25C
V
CM
= 1.5V
TPC 1. Input Offset Voltage
Distribution
OFFSET VOLTAGE DRIFT, TCV
OS
– µV/C
QUANTITY
300
0
00.25 1.50.50 0.75 1.0 1.25
250
200
150
100
50
V
S
= 5V
–40C T
A
+125C
TPC 4. Input Offset Voltage Drift
Distribution
COMMON MODE VOLTAGE – V
INPUT BIAS CURRENT – nA
500
–500
–15 –10 15–5 5 100
400
300
200
100
0
–100
–200
–300
–400
V
S
= 15V
TPC 7. Input Bias Current vs.
Common-Mode Voltage
–6–
INPUT OFFSET VOLTAGE – V
QUANTITY
300
0
–100 –75 100
–50 –25 0 25 50 75
270
180
90
60
30
240
210
120
150
VS = 5V
TA = 25C
VCM = 2.5V
TPC 2. Input Offset Voltage
Distribution
OFFSET VOLTAGE DRIFT, TCV
OS
– µV/C
QUANTITY
300
000.25 1.50.50 0.75 1.0 1.25
250
200
150
100
50
V
S
= ±15V
–40C T
A
+125C
TPC 5. Input Offset Voltage Drift
Distribution
LOAD CURRENT – mA
OUTPUT VOLTAGE – mV
1,000
100
10
0.01 0.1 10
1
VS = 15V
SOURCE
SINK
TPC 8. Output Voltage to Supply
Rail vs. Load Current
INPUT OFFSET VOLTAGE – V
QUANTITY
200
0
–125 –100 125
–75 –50 0 50 75 100
175
100
75
50
25
150
125
VS = ±15V
TA = 25C
–25 25
TPC 3. Input Offset Voltage
Distribution
TEMPERATURE – C
INPUT BIAS CURRENT – nA
–40
–80
–40 12525 85
–45
–50
–55
–60
–65
–70
–75
VS = 5V
VS = 15V
VCM = VS/2
TPC 6. Bias Current vs.
Temperature
TEMPERATURE – C
SUPPLY CURRENT/AMPLIFIER – mA
1.2
0.5
1.1
0.8
0.7
0.6
1.0
0.9
–40 12525 85
V
S
= 15V
V
S
= 5V
V
S
= 3V
TPC 9. Supply Current vs.
Temperature
OP184/OP284/OP484–Typical Performance Characteristics
REV. B
REV. B –7–
OP184/OP284/OP484
SUPPLY VOLTAGE – V
SUPPLY CURRENT (PER AMPLIFIER) – mA
1.50
002.5 205.0 10 12.5 15
1.25
1.00
0.75
0.50
0.25
17.57.5
T
A
= 25C
TPC 10. Supply Current vs. Supply
Voltage
0
45
90
135
180
225
270
PHASE SHIFT – Degrees
FREQUENCY – Hz
OPEN-LOOP GAIN – dB
60
10k 100k 10M
1M
40
20
0
–20
80
50
10
30
–10
–30
V
S
= 3V
T
A
= 25C
NO LOAD
TPC 13. Open-Loop Gain and Phase
vs. Frequency (No Load)
FREQUENCY – Hz
30
10
CLOSED-LOOP GAIN – dB
40
60
10
–40 100 10k 1M 10M
–10
–20
–30
0
20
50
1k 100k
VS = 5V
RL = 2k
TA = 25C
TPC 16. Closed-Loop Gain vs.
Frequency (2 k
Load)
TEMPERATURE – C
SHORT CIRCUIT CURRENT – mA
50
0
–50 125
40
30
20
10
V
S
= 15V
–25 0 25 7550 100
V
S
= 5V, V
CM
= 2.5V
+I
SC
–I
SC
–I
SC
+I
SC
TPC 11. Short Circuit Current vs.
Temperature
0
45
90
135
180
225
270
PHASE SHIFT – Degrees
FREQUENCY – Hz
OPEN-LOOP GAIN – dB
60
10k 100k 10M
1M
40
20
0
–20
80
50
10
30
–10
–30
V
S
= ±15V
T
A
= 25C
NO LOAD
TPC 14. Open-Loop Gain and Phase
vs. Frequency (No Load)
30
10
CLOSED-LOOP GAIN – dB
40
60
10
–40 100 10k 1M 10M
–10
–20
–30
0
20
50
1k 100k
V
S
= 15V
R
L
= 2k
T
A
= 25C
FREQUENCY – Hz
TPC 17. Closed-Loop Gain vs.
Frequency (2 k
Load)
0
45
90
135
180
225
270
PHASE SHIFT – Degrees
FREQUENCY – Hz
OPEN-LOOP GAIN – dB
60
10k 100k 10M
1M
40
20
0
–20
80
50
10
30
–10
–30
V
S
= 5V
T
A
= 25C
NO LOAD
TPC 12. Open-Loop Gain and Phase
vs. Frequency (No Load)
TEMPERATURE – C
OPEN-LOOP GAIN – V/mV
2.5k
0
–50 125
2k
1.5k
1k
500
–25 0 25 7550 100
VS = 5V
1V < VO < 4V
RL = 2k
VS = 15V
–10V < VO < 10V
RL = 2k
TPC 15. Open-Loop Gain vs.
Temperature
FREQUENCY – Hz
30
10
CLOSED-LOOP GAIN – dB
40
60
10
–40 100 10k 1M 10M
–10
–20
–30
0
20
50
1k 100k
VS = 3V
RL = 2k
TA = 25C
TPC 18. Closed-Loop Gain vs.
Frequency (2 k
Load)
REV. B
–8–
OP184/OP284/OP484
FREQUENCY – Hz
210
10
OUTPUT IMPEDANCE –
240
300
150
0
100 10k 1M 10M
90
60
30
120
180
270
1k 100k
V
S
= 5V
T
A
= 25C
A
V
= 1
A
V
= 100
A
V
= 10
TPC 19. Output Impedance vs.
Frequency
FREQUENCY – Hz
3
1k
MAXIMUM OUTPUT SWING – V p-p
4
5
2
010k 100k 1M 10M
1
V
S
= 5V
V
IN
= 0.5–4.5V
R
L
= 2k
T
A
= 25C
TPC 22. Maximum Output Swing
vs. Frequency
FREQUENCY – Hz
100
10
PSSR – dB
120
160
60
–40 100 10k 1M 10M
20
0
–20
40
80
140
1k 100k
T
A
= 25C
V
S
= 15V
V
S
= 5V
V
S
= 3V
TPC 25. PSRR vs. Frequency
FREQUENCY – Hz
210
10
OUTPUT IMPEDANCE –
240
300
150
0100 10k 1M 10M
90
60
30
120
180
270
1k 100k
V
S
= 15V
T
A
= 25C
A
V
= 100
A
V
= 1
A
V
= 10
TPC 20. Output Impedance vs.
Frequency
FREQUENCY – Hz
3
1k
MAXIMUM OUTPUT SWING – V p-p
4
5
2
010k 100k 1M 10M
1
V
S
= 15V
V
IN
= 14V
R
L
= 2k
T
A
= 25C
6
TPC 23. Maximum Output Swing
vs. Frequency
CAPACITIVE LOAD – pF
OVERSHOOT – %
80
70
0
10 100 1000
60
50
40
30
20
10
–OS
+OS
V
S
= 2.5V
T
A
= 25C, A
VCL
= 1
V
IN
= 50mV
TPC 26. Small Signal Overshoot vs.
Capacitive Load
FREQUENCY – Hz
210
10
OUTPUT IMPEDANCE –
240
300
150
0100 10k 1M 10M
90
60
30
120
180
270
1k 100k
V
S
= 3V
T
A
= 25C
A
V
= 100
A
V
= 10
A
V
= 1
TPC 21. Output Impedance vs.
Frequency
FREQUENCY – Hz
120
10
CMRR – dB
140
180
80
–20 100 10k 1M 10M
40
20
0
60
100
160
1k 100k
TA = 25C
VS = 15V
VS = 5V
VS = 3V
TPC 24. CMRR vs. Frequency
TEMPERATURE – C
SLEW RATE – V/s
7
0
–50 125
–25 0 75 100
6
3
2
1
5
4
25 50
+SLEW RATE
–SLEW RATE
V
S
= 15V
R
L
= 2k
V
S
= 5V
R
L
= 2k
+SLEW RATE
–SLEW RATE
TPC 27. Slew Rate vs. Temperature
REV. B –9–
OP184/OP284/OP484
30
01000
15
5
10
25
20
10010
FREQUENCY – Hz
1
2.5V V
S
±15V
T
A
= 25C
NOISE DENSITY – nV/ Hz
TPC 28. Voltage Noise Density
vs. Frequency
SETTLING TIME – s
STEP SIZE – V
10
–1001 624
8
6
4
2
0
53
–2
–4
–6
–8
V
S
= 15V
T
A
= 25C
0.1% 0.01%
TPC 31. Settling Time vs. Step Size
FREQUENCY – Hz
100
120
160
60
–40
20
0
–20
40
80
140
CHANNEL SEPARATION – dB
100 1k 100k 10M10k 1M
VS = 15V
VS = 3V
TA = 25C
TPC 34. Channel Separation
vs. Frequency
10
0
1000
2
4
8
6
10010
FREQUENCY – Hz
1
2.5V VS ±15V
TA = 25C
CURRENT NOISE DENSITY – pA/ Hz
TPC 29. Current Noise Density
vs. Frequency
10
0%
100
90
1s
10mV
V
S
= 15V
A
V
= 100k
e
n
= 0.3V p-p
TPC 32. 0.1 Hz to 10 Hz Noise
10
0%
100
90
1
s
100mV
V
S
= 5V
A
V
= 1
R
L
= OPEN
C
L
= 300pF
T
A
= 25C
400mV
0V
TPC 35. Small Signal Transient
Response
SETTLING TIME – s
STEP SIZE – V
5
–501 624
4
3
2
1
0
53
–1
–2
–3
–4
VS = 5V
TA = 25C
0.1% 0.01%
TPC 30. Settling Time vs. Step Size
10
0%
100
90
1s
V
S
= 5V, 0V
A
V
= 100k
e
n
= 0.3V p-p
10mV
TPC 33. 0.1 Hz to 10 Hz Noise
10
0%
100
90
1
s
100mV
VS = 5V
AV = 1
RL = 2k
CL = 300pF
TA = 25C
400mV
0V
TPC 36. Small Signal Transient
Response
REV. B
–10–
OP184/OP284/OP484
APPLICATIONS
Functional Description
The OP284 and OP484 are precision single-supply, rail-to-rail
operational amplifiers. Intended for the portable instrumenta-
tion marketplace, the OP184/OP284/OP484 combine the
attributes of precision, wide bandwidth, and low noise to make
it a superb choice in those single-supply applications that require
both ac and precision dc performance. Other low supply voltage
applications for which the OP284 is well suited are active filters,
audio microphone preamplifiers, power supply control, and
telecom. To combine all of these attributes with rail-to-rail
input/output operation, novel circuit design techniques are used.
D1
D2
Q4
R2
4k
VPOS
I1
R1
4k
Q3Q1 Q2
R4
3k
I2
R3
3k
V01
–IN
V02
VNEG
+IN
Figure 4. OP284 Equivalent Input Circuit
For example, Figure 4 illustrates a simplified equivalent circuit
for the OP184/OP284/OP484’s input stage. It is comprised of
an NPN differential pair, Q1–Q2, and a PNP differential pair,
Q3–Q4, operating concurrently. Diode network D1–D2
serves to clamp the applied differential input voltage to the
OP284, thereby protecting the input transistors against ava-
lanche damage. Input stage voltage gains are kept low for input
rail-to-rail operation. The two pair of differential output volt-
ages are connected to the OP284’s second stage, which is a
compound folded cascode gain stage. It is also in the second
gain stage where the two pairs of differential output voltages are
combined into a single-ended output signal voltage used to drive
the output stage. A key issue in the input stage is the behavior of
the input bias currents over the input common-mode voltage
range. Input bias currents in the OP284 are the arithmetic sum
of the base currents in Q1–Q3 and in Q2–Q4. As a result of
this design approach, the input bias currents in the OP284 not
only exhibit different amplitudes, but also exhibit different po-
larities. This effect is best illustrated in TPC 6. It is, therefore,
of paramount importance that the effective source impedances
connected to the OP284’s inputs be balanced for optimum dc and
ac performance.
To achieve rail-to-rail output, the OP284 output stage design
employs a unique topology for both sourcing and sinking current.
This circuit topology is illustrated in Figure 5. As previously
mentioned, the output stage is voltage-driven from the second
gain stage. The signal path through the output stage is inverting;
that is, for positive input signals, Q1 provides the base current
drive to Q6 so that it conducts (sinks) current. For negative
input signals, the signal path via Q1–Q2–D1–Q4–Q3 provides
the base current drive for Q5 to conduct (source) current.
Both amplifiers provide output current until they are forced
into saturation, which occurs at approximately 20 mV from
negative rail and 100 mV from the positive supply rail.
V
POS
I2
I1
Q1 Q3
Q4
Q2
V
NEG
Q5
V
OUT
Q6
R6
R3
R2
R1
R4
INPUT FROM
SECOND GAIN
STAGE
R5
D1
Figure 5. OP284 Equivalent Output Circuit
10
0%
100
90
500ns
100mV
V
S
= 1.5V
A
V
= 1
NO LOAD
T
A
= 25C
200mV
0V
–200mV
TPC 37. Small Signal Transient
Response
200mV
0V
–200mV 10
0%
100
90
1
s
100mV
V
S
= 0.75V
A
V
= 1
NO LOAD
T
A
= 25C
TPC 38. Small Signal Transient
Response
FREQUENCY – Hz
THD+N – %
0.1
0.010
0.000520 100 10k
1k
0.001
20k
VO = 0.75V
VO = 2.5V
VO = 1.5V
AV = 1000
VS = 2.5V
RL = 2k
TPC 39. Total Harmonic Distortion
vs. Frequency
REV. B –11–
OP184/OP284/OP484
Thus, the saturation voltage of the output transistors sets the
limit on the OP284’s maximum output voltage swing. Output
short circuit current limiting is determined by the maximum
signal current into the base of Q1 from the second gain stage.
Under output short circuit conditions, this input current level is
approximately 100 µA. With transistor current gains around
200, the short circuit current limits are typically 20 mA. The
output stage also exhibits voltage gain. This is accomplished by
use of common-emitter amplifiers, and as a result, the voltage
gain of the output stage (thus, the open-loop gain of the device)
exhibits a dependence to the total load resistance at the output
of the OP284.
Input Overvoltage Protection
As with any semiconductor device, if conditions exist where
the applied input voltages to the device exceed either supply
voltage, the device’s input overvoltage I-V characteristic must
be considered. When an overvoltage occurs, the amplifier could
be damaged, depending on the magnitude of the applied voltage
and the magnitude of the fault current. Figure 6 illustrates the
overvoltage I-V characteristic of the OP284. This graph was
generated with the supply pins connected to GND and a curve
tracer’s collector output drive connected to the input.
5
4
3
2
1
0
–1
–2
–3
–4
–5
–5 –4 –3 –2 1 0 1 2 3 4 5
INPUT CURRENT – mA
INPUT VOLTAGE – Volts
Figure 6. Input Overvoltage I-V Characteristics of the
OP284
As shown in the figure, internal p-n junctions to the OP284
energize and permit current flow from the inputs to the supplies
when the input is 1.8 V more positive and 0.6 V more negative
than the respective supply rails. As illustrated in the simplified
equivalent circuit shown in Figure 4, the OP284 does not have
any internal current limiting resistors; thus, fault currents can
quickly rise to damaging levels.
This input current is not inherently damaging to the device,
provided that it is limited to 5 mA or less. For the OP284, once
the input exceeds the negative supply by 0.6 V, the input current
quickly exceeds 5 mA. If this condition continues to exist, an
external series resistor should be added at the expense of addi-
tional thermal noise. Figure 7 illustrates a typical noninverting
configuration for an overvoltage protected amplifier where the
series resistance, R
S
, is chosen such that:
RS=VIN (MAX )VSUPPLY
5mA
R1
R2
VIN
VOUT
1/2
OP284
Figure 7. A Resistance in Series with an Input Limits
Overvoltage Currents to Safe Values
For example, a 1 k resistor will protect the OP284 against
input signals up to 5 V above and below the supplies. For other
configurations where both inputs are used, then each input should
be protected against abuse with a series resistor. Again, in order
to ensure optimum dc and ac performance, it is recommended
to balance source impedance levels. For more information on
the general overvoltage characteristics of amplifiers, please refer
to the 1993 System Applications Guide, Section 1, pages 56-69.
This reference textbook is available from the Analog Devices
Literature Center.
Output Phase Reversal
Some operational amplifiers designed for single-supply opera-
tion exhibit an output voltage phase reversal when their inputs
are driven beyond their useful common-mode range. Typically
for single-supply bipolar op amps, the negative supply deter-
mines the lower limit of their common-mode range. With these
devices, external clamping diodes, with the anode connected to
ground and the cathode to the inputs, prevent input signal
excursions from exceeding the device’s negative supply (i.e.,
GND), preventing a condition that could cause the output
voltage to change phase. JFET-input amplifiers may also exhibit
phase reversal, and, if so, a series input resistor is usually required
to prevent it.
The OP284 is free from reasonable input voltage range restric-
tions, provided that input voltages no greater than the supply
voltages are applied. Although the device’s output will not
change phase, large currents can flow through the input protec-
tion diodes as was shown in Figure 6. Therefore, the technique
recommended in the Input Overvoltage Protection section
should be applied to those applications where the likelihood of
input voltages exceeding the supply voltages is high.
Designing Low Noise Circuits in Single Supply Applications
In single supply applications, devices like the OP284 extend the
dynamic range of the application through the use of rail-to-rail
operation. In fact, the OP284 family is the first of its kind to
combine single-supply, rail-to-rail operation and low noise in
one device. It is the first device in the industry to exhibit an
input noise voltage spectral density of less than 4 nV/Hz at
1 kHz. It was also designed specifically for low-noise, single-
supply applications, and as such, some discussion on circuit
noise concepts in single-supply applications is appropriate.
REV. B
–12–
OP184/OP284/OP484
Referring to the op amp noise model circuit configuration illus-
trated in Figure 8, the expression for an amplifier’s total
equivalent input noise voltage for a source resistance level R
S
is
given by:
e
nT
=2e
nR
()
2
+i
nOA
×R
()
2
[]
+e
nOA
()
2
,units in V
Hz
where R
S
= 2R = Effective, or equivalent, circuit source
resistance,
(e
nOA
)
2
= Op amp equivalent input noise voltage spectral
power (1 Hz BW),
(i
nOA
)
2
= Op amp equivalent input noise current spectral
power (1 Hz BW),
(e
nR
)
2
= Source resistance thermal noise voltage power =
(4kTR),
k = Boltzmann’s constant = 1.38 × 10
–23
J/K, and
T = Ambient temperature of the circuit, in Kelvin, =
273.15 + T
A
(°C)
i
NOA
e
NR
e
NOA
R
"NOISELESS"
i
NOA
e
NR
R
"NOISELESS"
IDEAL
NOISELESS
OP AMP
R
S
= 2R
Figure 8. Op Amp Noise Circuit Model Used to
Determine Total Circuit Equivalent Input Noise Voltage
and Noise Figure
As a design aid, Figure 9 illustrates the total equivalent input
noise of the OP284 and the total thermal noise of a resistor for
comparison. Note that for source resistance less than 1 k, the
equivalent input noise voltage of the OP284 is dominant.
TOTAL SOURCE RESISTANCE, R
S
100
0
100 100k
EQUIVALENT THERMAL NOISE – nV/ Hz
10
10k1k
FREQUENCY = 1kHz
T
A
= 25C
OP284 TOTAL
EQUIVALENT NOISE
RESISTOR THERMAL
NOISE ONLY
Figure 9. OP284 Total Noise vs. Source Resistance
Since circuit SNR is the critical parameter in the final analysis,
the noise behavior of a circuit is often expressed in terms of its
noise figure, NF. Noise figure is defined as the ratio of a circuit’s
output signal-to-noise to its input signal-to-noise. An expres-
sion of a circuit’s NF in dB, and in terms of the operational
amplifier’s voltage and current noise parameters defined previ-
ously, is given by:
NF (dB)=10 log 1 +enOA
()
2+inOA R
S
()
2
enRS
()
2
where NF (dB) = Noise figure of the circuit, expressed in dB,
R
S
= Effective, or equivalent, source resistance presented
to amplifier,
(e
nOA
)
2
= OP284 noise voltage spectral power (1 Hz BW),
(i
nOA
)
2
= OP284 noise current spectral power (1 Hz BW),
(e
nRS
)
2
= Source resistance thermal noise voltage power
= (4kTR
S
),
Circuit noise figure is straightforward to calculate because the
signal level in the application is not required to determine it.
However, many designers using NF calculations as the basis for
achieving optimum SNR believe that low noise figure is equal to
low total noise. In fact, the opposite is true, as illustrated in
Figure 10. Here, the noise figure of the OP284 is expressed as a
function of the source resistance level. Note that the lowest
noise figure for the OP284 occurs at a source resistance level of
10 k. However, Figure 9 shows that this source resistance level
and the OP284 generate approximately 14 nV/Hz of total
equivalent circuit noise. Signal levels in the application would
invariably be increased to maximize circuit SNR—not an option
in low voltage, single-supply applications.
TOTAL SOURCE RESISTANCE, RS
10
100 100k
NOISE FIGURE – dB
5
10k1k
0
9
8
7
6
4
3
2
1
FREQUENCY = 1kHz
TA = 25C
Figure 10. OP284 Noise Figure vs. Source Resistance
In single supply applications, therefore, it is recommended for
optimum circuit SNR to choose an operational amplifier with
the lowest equivalent input noise voltage and to choose source
resistance levels consistent in maintaining low total circuit noise.
REV. B –13–
OP184/OP284/OP484
Overdrive Recovery
The overdrive recovery time of an operational amplifier is the time
required for the output voltage to recover to its linear region
from a saturated condition. The recovery time is important in
applications where the amplifier must recover quickly after a
large transient event. The circuit shown in Figure 11 was used
to evaluate the OP284’s overload recovery time. The OP284
takes approximately 2 µs to recover from positive saturation and
approximately 1 µs to recover from negative saturation.
2
3
1
+5V
8
4
R3
9k
R1
10k
R2
10k
V
IN
10V STEP –5V
V
OUT
1/2
OP284
Figure 11. Output Overload Recovery Test Circuit
A Single-Supply, 3 V Instrumentation Amplifier
The OP284’s low noise, wide bandwidth, and rail-to-rail input/
output operation makes it ideal for low supply voltage applica-
tions such as in a two op amp instrumentation amplifier as
shown in Figure 12. The circuit uses the classic two op amp
instrumentation amplifier topology with four resistors to set the
gain. The transfer equation of the circuit is identical to that of a
noninverting amplifier. Resistors R2 and R3 should be closely
matched to each other as well as to resistors (R1 + P1) and R4
to ensure good common-mode rejection performance. Resistor
networks should be used in this circuit for R2 and R3 because they
exhibit the necessary relative tolerance matching for good per-
formance. Matched networks also exhibit tight relative resistor
temperature coefficients for good circuit temperature stability.
Trimming potentiometer P1 is used for optimum dc CMR
adjustment, and C1 is used to optimize ac CMR. With the
circuit values as shown, circuit CMR is better than 80 dB over
the frequency range of 20 Hz to 20 kHz. Circuit RTI (Referred-to-
Input) noise in the 0.1 Hz to 10 Hz band is an impressively low
0.45 µV p-p. Resistors RP1 and RP2 serve to protect the OP284’s
inputs against input overvoltage abuse. Capacitor C2 can be
included to the limit circuit bandwidth and, therefore, wide
bandwidth noise in sensitive applications. The value of this
capacitor should be adjusted depending on the required closed-
loop bandwidth of the circuit. The R4-C2 time constant creates
a pole at a frequency equal to:
f(3dB)=1
2πR4C2
V
OUT
R3
1.1k
5
6
7
3V
A1, A2 = 1/2 OP284
GAIN = 1 + R4
R3
SET R2 = R3
R1 + P1 = R4
8
4
R4
10k
C2
RP1
1k
RP2
1k
R2
1.1k
R1
9.53k
P1
500
3
2
1
C1
AC CMRR
TRIM
5pF–40pF
V
IN
A1
+
A2
Figure 12. A Single Supply, 3 V Low Noise Instrumenta-
tion Amplifier
A 2.5 V Reference from a 3 V Supply
In many single-supply applications, the need for a 2.5 V refer-
ence often arises. Many commercially available monolithic
2.5 V references require at least a minimum operating supply of
4 V. The problem is exacerbated when the minimum operating
supply voltage is 3 V. The circuit illustrated in Figure 13 is an
example of a 2.5 V reference that operates from a single 3 V
supply. The circuit takes advantage of the OP284’s rail-to-rail
input/output voltage ranges to amplify an AD589’s 1.235 V
output to 2.5 V. The OP284’s low TCV
OS
of 1.5 µV/°C helps
maintain an output voltage temperature coefficient that is domi-
nated by the temperature coefficients of R2 and R3. In this
circuit with 100 ppm/°C TCR resistors, the output voltage
exhibits a temperature coefficient of 200 ppm/°C. Lower tempco
resistors are recommended for more accurate performance over
temperature.
One measure of the performance of a voltage reference is its
capacity to recover from sudden changes in load current. While
sourcing a steady-state load current of 1 mA, this circuit recov-
ers to 0.01% of the programmed output voltage in 1.5 µs for a
total change in load current of ±1 mA.
2.5V
REF
P1
5k
3
2
1
3V
8
4
R2
100k
R3
100k
3V
0.1F
R1
17.4k
AD589
RESISTORS = 1%, 100ppm/C
POTENTIOMETER = 10 TURN, 100ppm/C
1/2
OP284
Figure 13. A 2.5 V Reference that Operates on a Single
3 V Supply
REV. B
–14–
OP184/OP284/OP484
A 5 V Only, 12-Bit DAC Swings Rail-to-Rail
The OP284 is ideal for use with a CMOS DAC to generate a
digitally controlled voltage with a wide output range. Figure 14
shows a DAC8043 used in conjunction with the AD589 to
generate a voltage output from 0 V to 1.23 V. The DAC is
actually operating in “voltage switching” mode where the refer-
ence is connected to the current output, I
OUT
, and the output
voltage is taken from the V
REF
pin. This topology is inherently
noninverting as opposed to the classic current output mode,
which is inverting and not usable in single-supply applications.
VOUT = –––– (5V)
D
4096
R4
100k
1%
3
2
1
5V
8
4
R2
32.4k
1%
R3
232
1%
R1
17.8k
AD589 GND CLK SR1 LD
VREF
RFB
VDD
IOUT
1.23V
47 65
8
2
13 DAC8043
5V
DIGITAL
CONTROL
1/2
OP284
Figure 14. A 5 V Only, 12-Bit DAC Swings Rail-to-Rail
In this application the OP284 serves two functions. First, it
buffers the high output impedance of the DAC’s V
REF
pin,
which is on the order of 10 k. The op amp provides a low
impedance output to drive any following circuitry. Second, the
op amp amplifies the output signal to provide a rail-to-rail out-
put swing. In this particular case, the gain is set to 4.1 so that
the circuit generates a 5 V output when the DAC output is at
full scale. If other output voltage ranges are needed, such as 0 V
V
OUT
4.095 V, the gain can be easily changed by adjusting
the values of R2 and R3.
A High-Side Current Monitor
In the design of power supply control circuits, a great deal of
design effort is focused on ensuring a pass transistor’s long-term
reliability over a wide range of load current conditions. As a
result, monitoring and limiting device power dissipation is of
prime importance in these designs. The circuit illustrated in
Figure 15 is an example of a 3 V, single-supply high-side current
monitor that can be incorporated into the design of a voltage
regulator with fold-back current limiting or a high current power
supply with crowbar protection. This design uses an OP284’s
rail-to-rail input voltage range to sense the voltage drop across a
0.1 current shunt. A p-channel MOSFET used as the feedback
element in the circuit converts the op amp’s differential input
voltage into a current. This current is applied to R2 to generate
a voltage that is a linear representation of the load current. The
transfer equation for the current monitor is given by:
Monitor Output =R2×RSENSE
R1
×IL
For the element values shown, the Monitor Output’s transfer
characteristic is 2.5 V/A.
8
1
4
3
3V 0.1F
R
SENSE
0.13V
I
L
G
S
D
2
M1
Si9433
MONITOR
OUTPUT
3V
R2
2.49k
R1
100
1/2
OP284
Figure 15. A High-Side Load Current Monitor
Capacitive Load Drive Capability
The OP284 exhibits excellent capacitive load driving capabili-
ties. It can drive up to 1 nF as shown in TPC 24. Even though
the device is stable, a capacitive load does not come without
penalty in bandwidth. The bandwidth is reduced to under
1 MHz for loads greater than 2 nF. A “snubber” network on the
output does not increase the bandwidth, but it does significantly
reduce the amount of overshoot for a given capacitive load. A
snubber consists of a series R-C network (R
S
, C
S
), as shown in
Figure 16, connected from the output of the device to ground.
This network operates in parallel with the load capacitor, C
L
, to
provide the necessary phase lag compensation. The value of the
resistor and capacitor is best determined empirically.
5V
RS
50CL
1nF
CS
100nF
VIN
100mVp-p
0.1F
VOUT
1/2
OP284
Figure 16. Snubber Network Compensates for Capacitive
Load
The first step is to determine the value of the resistor R
S
. A
good starting value is 100 (typically, the optimum value will
be less than 100 ). This value is reduced until the small-signal
transient response is optimized. Next, C
S
is determined—10 µF
is a good starting point. This value is reduced to the smallest
value for acceptable performance (typically, 1 µF). For the case
of a 10 nF load capacitor on the OP284, the optimal snubber
network is a 20 in series with 1 µF. The benefit is immediately
apparent as shown in the scope photo in Figure 17. The top
trace was taken with a 1 nF load, and the bottom trace was
taken with the 50 , 100 nF snubber network in place. The
amount of overshoot and ringing is dramatically reduced.
Table I below illustrates a few sample snubber networks for
large load capacitors.
REV. B –15–
OP184/OP284/OP484
R9
27.4k
C4
0.1F
C5
0.01F
R11
1k
R6
4.99k
R8
301k
+V
S
R10
1k
R2
8.06k
C3
0.1F
R
S
0.05
C6
10F
3
2
1
8
4
R7
4.99k
U1A
OP284
D2
AD589
D1
1N4148
R5
22.1k
Q1
SI9433DY
R4
2.21k
6
5
7
C1
0.01F
U1B
OP284
D3
1N4148
2
6
4
3
U2
REF192
C2
1F
R1
4.53k
V
OUT
2
2.5V
R3
10k5.0V
4.5V
3.3V
3.0V
4.99
4.53
2.43
1.69
10.0
8.06
3.24
2.00
10.0
10.0
10.0
10.0
V
OUT
R1kR2kR3k
OUTPUT TABLE
V
S
>
V
OUT
+ 0.1V
OPTIONAL
ON/OFF CONTROL INPUT
CMOS HI (OR OPEN) = ON
LO = OFF
V
IN
COMMON
V
C
V
OUT
=
4.5V @ 350mA
(SEE TABLE)
V
OUT
COMMON
Figure 18. A Low Dropout Regulator with Current Limiting
10
0%
100
90
1nF LOAD
ONLY
SNUBBER
IN
CIRCUIT
50mv50mv2
s
s
DLY
L
W
B
Figure 17. Overshoot and Ringing Is Reduced by Adding a
“Snubber” Network in Parallel with the 1 nF Load
Table I. Snubber Networks for Large Capacitive Loads
Load Capacitance Snubber Network
(C
L
)(R
S
, C
S
)
1 nF 50 , 100 nF
10 nF 20 , 1 µF
100 nF 5 , 10 µF
A Low Dropout Regulator with Current Limiting
Many circuits require stable regulated voltages relatively close,
in potential to an unregulated input source. This “low dropout”
type of regulator is readily implemented with a rail-to-rail out-
put op amp such as the OP284 because the wide output swing
allows easy drive to a low saturation voltage pass device. Fur-
thermore, it is particularly useful when the op amp also enjoys a
rail-to-rail input feature, as this factor allows it to perform high-
side current sensing for positive rail current limiting. Typical
examples are voltages developed from 3 V to 9 V range system
sources or anywhere where low dropout performance is required
for power efficiency. The 4.5 V case here works from 5 V nomi-
nal sources with worst-case levels down to 4.6 V or less.
Figure 18 shows such a regulator set up using an OP284 plus a
low R
DS(ON)
, P-channel MOSFET pass device. Part of the low
dropout performance of this circuit is provided by Q1, which
has a rating of 0.11 with a gate drive voltage of only 2.7 V.
This relatively low gate drive threshold allows operation of the
regulator on supplies as low as 3 V without compromising over-
all performance.
The circuit’s main voltage control loop operation is provided by
U1B, half of the OP284. This voltage control amplifier amplifies
the 2.5 V reference voltage produced by three terminal U2, a
REF192. The regulated output voltage V
OUT
is then:
V
OUT
=V
OUT 2
1+R2
R3
()
For this example, since V
OUT
of 4.5 V with V
OUT2
= 2.5 V requires
a U1B gain of 1.8 times, R3 and R2 are chosen for a ratio of
1.2:1 or 10.0 k:8.06 k (using closest 1% values). Note that
for the lowest V
OUT
dc error, R2R3 should be maintained equal
to R1 (as here), and the R2-R3 resistors should be stable, close
tolerance metal film types. The table in Figure 18 summarizes
R1-R3 values for some popular voltages. However, note that, in
general, the output can be anywhere between V
OUT2
and the
12 V maximum rating of Q1.
While the low voltage saturation characteristic of Q1 is a key
part of the low dropout, another component is a low current
sense comparison threshold with good dc accuracy. Here, this is
provided by current sense amplifier U1A, which is provided by a
20 mV reference from the 1.235 V AD589 reference diode D2
and the R7-R8 divider. When the product of the output current
and the R
S
value match this voltage threshold, the current con-
trol loop is activated, and U1A drives Q1’s gate through D1.
This causes the overall circuit operation to enter current mode
control with a current limit I
LIMIT
defined as:
ILIMIT =VR(D2)
R
S
R7
R7+R8
()
REV. B
–16–
OP184/OP284/OP484
Obviously, it is desirable to keep this comparison voltage small,
since it becomes a significant portion of the overall dropout
voltage. Here, the 20 mV reference is higher than the typical
offset of the OP284 but still reasonably low as a percentage of
V
OUT
(< 0.5%). In adapting the limiter for other I
LIMIT
levels,
sense resistor R
S
should be adjusted along with R7-R8, to main-
tain this threshold voltage between 20 mV and 50 mV.
Performance of the circuit is excellent. For the 4.5 V output
version, the measured dc output change for a 225 mA load
change was on the order of a few microvolts while the dropout
voltage at this same current level was about 30 mV. The current
limit as shown is 400 mA, which allows the circuit to be used at
levels up to 300 mA or more. While the Q1 device can actually
support currents of several amperes, a practical current rating
takes into account the SO-8 device’s 2.5 W, 25°C dissipation.
Because a short circuit current of 400 mA at an input level of
5 V will cause a 2 W dissipation in Q1, other input conditions
should be considered carefully in terms of Q1’s potential over-
heating. Of course, if higher powered devices are used for Q1,
this circuit can support outputs of tens of amperes as well as the
higher V
OUT
levels noted above.
The circuit shown can be used either as a standard low dropout
regulator, or it can be used with ON/OFF control. By driving
Pin 3 of U1 with the optional logic control signal V
C
, the output
is switched between ON and OFF. Note that when the output is
OFF in this circuit, it is still active (i.e., not an open circuit). This
is because the OFF state simply reduces the voltage input to R1,
leaving the U1A/B amplifiers and Q1 still active.
When ON/OFF control is used, resistor R10 should be used
with U1 to speed ON-OFF switching and to allow the output of
the circuit to settle to a nominal zero voltage. Components D3
and R11 also aid in speeding up the ON-OFF transition by
providing a dynamic discharge path for C2. OFF-ON transition
time is less than 1 ms, while the ON-OFF transition is longer
but under 10 ms.
A 3 V, 50 Hz/60 Hz Active Notch Filter with False Ground
To process signals in a single-supply system, it is often best
to use a false ground biasing scheme. A circuit that uses this
approach is illustrated in Figure 19. In this circuit, a false-ground
circuit biases an active notch filter used to reject 50 Hz/60 Hz
power line interference in portable patient monitoring equip-
ment. Notch filters are quite commonly used to reject power
line frequency interference that often obscures low frequency
physiological signals, such as heart rates, blood pressure read-
ings, EEGs, EKGs, etc. This notch filter effectively squelches
60 Hz pickup at a filter Q of 0.75. Substituting 3.16 k resis-
tors for the 2.67 k in the twin-T section (R1 through R5)
configures the active filter to reject 50 Hz interference.
1
3
5
6
7
11
2
3V
R1
2.67kC1
1F
C2
1F
R3
2.67k
C3
2F
(1F x 2)
R4
2.67k
R5
1.33k
(2.67k ÷ 2)
R2
2.67k
V
O
R6
10k
V
IN
R8
1k
A2
A1
8
A3
R7
1k
R11
10k
4
10
9
C5
0.03F
R12
150
R10
20k
C4
1F
R9
20k
3V
1.5V
C6
1F
A1, A2, A3 = OP484
Q = 0.75
NOTE: FOR 50Hz APPLICATIONS
CHANGE R1–R4 TO 3.1k
AND R5 TO 1.58k(3.16k ÷ 2).
Figure 19. A 3 V Single Supply, 50/60 Hz Active Notch
Filter with False Ground
Amplifier A3 is the heart of the false-ground bias circuit. It
simply buffers the voltage developed at R9 and R10 and is the
reference for the active notch filter. Since the OP484 exhibits a
rail-to-rail input common-mode range, R9 and R10 are chosen
to split the 3 V supply symmetrically. An in-the-loop compensa-
tion scheme is used around the OP484 that allows the op amp
to drive C6, a 1 µF capacitor, without oscillation. C6 maintains
a low impedance ac ground over the operating frequency range
of the filter.
The filter section uses a OP484 in a twin-T configuration whose
frequency selectivity is very sensitive to the relative matching of
the capacitors and resistors in the twin-T section. Mylar is the
material of choice for the capacitors, and the relative match-
ing of the capacitors and resistors determines the filter’s pass
band symmetry. Using 1% resistors and 5% capacitors produces
satisfactory results.
REV. B –17–
OP184/OP284/OP484
*OP284 SPICE Macro-model 9/94 / Rev. A
*ARG/ADI
*
* Copyright 1995 by Analog Devices
*
* Refer to “README.DOC” file for License Statement. Use of
this model
* indicates your acceptance of the terms and provisions in the
License
* Statement.
*
* Node assignments
*noninverting input
*| inverting input
*| | positive supply
*| | | negative supply
*| | | | output
*| | | | |
.SUBCKT OP284 1 2 99 50 45
*
* INPUT STAGE
*
Q1 5 23QIN 1
Q2 6 11 3 QIN 1
Q3 7 24QIP 1
Q4 8 11 4 QIP 1
DC1 2 11 DC
DC2 11 2 DC
Q5 4 9 99 QIP 1
Q6 9 9 99 QIP 1
Q7 3 10 50QIN 1
Q8 10 10 50 QIN 1
R1 99 5 4E3
R2 99 6 4E3
R3 7 50 4E3
R4 8 50 4E3
IREF 9 10 50.5E-6
EOS 1 11 POLY(2) (22,98) (14,98) -25E-6 1E-2 1
IOS 2 1 5E-9
CIN 1 2 2E-12
GN1 98 1 (17,98) 1E-3
GN2 98 2 (23,98) 1E-3
*
* VOLTAGE NOISE SOURCE WITH FLICKER NOISE
*
VN1 13 98 DC 2
VN2 98 15 DC 2
DN1 13 14 DEN
DN2 14 15 DEN
*
* CURRENT NOISE SOURCE WITH FLICKER NOISE
*
VN3 16 98 DC 2
VN4 98 18 DC 2
DN3 16 17 DIN
DN4 17 18 DIN
*
* 2ND CURRENT NOISE SOURCE WITH FLICKER
NOISE
*
VN5 19 98 DC 2
VN6 98 24 DC 2
DN5 19 23 DIN
DN6 23 24 DIN
*
* GAIN STAGE
*
EREF 98 0 POLY(2) (99,0) (50,0) 0 0.5 0.5
G1 98 20 POLY(2) (6,5) (8,7) 0 0.5E-3 0.5E-3
R9 20 98 1E3
*
* COMMON MODE STAGE WITH ZERO AT 100Hz
*
ECM 98 21 POLY(2) (1,98) (2,98) 0 0.5 0.5
R10 21 22 1
R11 22 98 100E-6
C4 21 22 1.592E-3
*
* NEGATIVE ZERO AT 20MHz
*
E1 27 98 (20,98) 1E6
R17 27 28 1
R18 28 98 1E-6
C8 25 26 7.958E-9
ENZ 25 98 (27,28) 1
VNZ 26 98 DC 0
FNZ 27 28 VNZ -1
*
* POLE AT 40MHz
*
G4 98 29 (28,98) 1
R19 29 98 1
C9 29 98 3.979E-9
*
* POLE AT 40MHz
*
G5 98 30 (29,98) 1
R20 30 98 1
C10 30 98 3.979E-9
*
* OUTPUT STAGE
*
ISY 99 50 0.276E-3
GIN 50 31 POLY(1) (30,98) .862574E-6 505.879E-6
RIN 31 50 2.75E6
VB 99 32 0.7
Q11 32 31 33 QON 1
R21 33 34 4.5E3
I1 34 50 50E-6
R22 99 35 6E3
Q12 36 36 35 QOP 1
I2 36 50 50E-6
R23 99 37 2.6E3
R24 34 38 5E3
Q13 39 36 37 QOP 1
Q14 39 38 40 QON 1.5
R25 40 50 40
Q15 39 39 41 QON 1
R26 41 42 1E3
R27 99 43 220
Q16 44 44 43 QOP 1.5
Q17 44 39 42 QON 1
R28 42 50 2E3
VSCP 99 97 DC 0
REV. B
–18–
OP184/OP284/OP484
FSCP 46 99 VSCP 1
RSCP 46 99 40
Q20 44 46 99 QOP 1
Q18 45 44 97 QOP 4.5
Q19 45 34 51 QON 4.5
VSCN 51 50 DC 0
FSCN 50 47 VSCN 1
RSCN 47 50 40
Q21 34 47 50 QON 1
CC2 31 45 20E-12
CF1 31 34 15E-12
CF2 31 42 15E-12
CO1 34 45 15E-12
CO2 42 45 5E-12
D3 45 99 DX
D4 50 45 DX
.MODEL DC D(IS=130E-21)
.MODEL DX D()
.MODEL DEN D(RS=100 KF=12E-15 AF=1)
.MODEL DIN D(RS=5.358 KF=56E-15 AF=1)
.MODEL QIN NPN(BF=200 VA=200 IS=0.5E-16)
.MODEL QIP PNP(BF=100 VA=60 IS=0.5E-16)
.MODEL QON NPN(BF=200 VA=200 IS=0.5E-16 RC=50)
.MODEL QOP PNP(BF=200 VA=200 IS=0.5E-16 RC=160)
.ENDS
REV. B –19–
OP184/OP284/OP484
8-Lead Plastic Dual-in-Line Package [PDIP]
(N-8)
Dimensions shown in inches and (millimeters)
SEATING
PLANE
0.015
(0.38)
MIN
0.180
(4.57)
MAX
0.150 (3.81)
0.130 (3.30)
0.110 (2.79) 0.060 (1.52)
0.050 (1.27)
0.045 (1.14)
8
14
5
0.295 (7.49)
0.285 (7.24)
0.275 (6.98)
0.100 (2.54)
BSC
0.375 (9.53)
0.365 (9.27)
0.355 (9.02)
0.150 (3.81)
0.135 (3.43)
0.120 (3.05)
0.150 (0.38)
0.010 (0.25)
0.008 (0.20)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES)
COMPLIANT TO JEDEC STANDARDS MO-095AA
8-Lead Standard Small Outline Package [SOIC]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
0.25 (0.0098)
0.19 (0.0075)
1.27 (0.0500)
0.41 (0.0160)
0.50 (0.0196)
0.25 (0.0099) 45
8
0
1.75 (0.0688)
1.35 (0.0532)
SEATING
PLANE
0.25 (0.0098)
0.10 (0.0040)
85
41
5.00 (0.1968)
4.80 (0.1890)
4.00 (0.1574)
3.80 (0.1497)
1.27 (0.0500)
BSC
6.20 (0.2440)
5.80 (0.2284)
0.51 (0.0201)
0.33 (0.0130)
COPLANARITY
0.10
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MS-012AA
OUTLINE DIMENSIONS
14-Lead Plastic Dual-in-Line Package [PDIP]
(N-14)
Dimensions shown in inches and (millimeters)
14
17
8
0.685 (17.40)
0.665 (16.89)
0.645 (16.38)
0.295 (7.49)
0.285 (7.24)
0.275 (6.99)
0.100 (2.54)
BSC
SEATING
PLANE
0.180 (4.57)
MAX
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.150 (3.81)
0.130 (3.30)
0.110 (2.79) 0.060 (1.52)
0.050 (1.27)
0.045 (1.14)
0.150 (3.81)
0.135 (3.43)
0.120 (3.05)
0.015 (0.38)
0.010 (0.25)
0.008 (0.20)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.015 (0.38)
MIN
CONTROLLING DIMENSIONS ARE IN INCH; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MO-095-AB
14-Lead Standard Small Outline Package [SOIC]
Narrow Body
(R-14)
Dimensions shown in millimeters and (inches)
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COPLANARITY
0.10
14 8
7
1
6.20 (0.2441)
5.80 (0.2283)
4.00 (0.1575)
3.80 (0.1496)
8.75 (0.3445)
8.55 (0.3366)
1.27 (0.0500)
BSC
SEATING
PLANE
0.25 (0.0098)
0.10 (0.0039)
0.51 (0.0201)
0.33 (0.0130)
1.75 (0.0689)
1.35 (0.0531)
8
0
0.50 (0.0197)
0.25 (0.0098) 45
1.27 (0.0500)
0.40 (0.0157)
0.25 (0.0098)
0.19 (0.0075)
Revision History
Location Page
6/02—Data Sheet changed from REV. 0 to REV. A.
9/02—Data Sheet changed from REV. A to REV. B.
Updated PIN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications changed; Input Bias Current max changed to 450 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ORDERING GUIDE updated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PRINTED IN U.S.A. C00293–0–9/02(B)
–20–