CRYPTORF® EPOXY GLASS TAGS
CryptoRF is a 13.56 MHz RFID device family with a 64-bit embedded hardware encryption engine, mutual authentication capability, and
up to 64-Kbits of user memory. Based on ISO 14443-B standard, CryptoRF is ideally suited to meet a variety of security applications such
as contactless payment, product authentication, patient safety, and patron management.
CryptoRF devices are great for proximity applications where hardware security is desired or when environmental factors such as dirt,
moisture, chemicals, etc., exist.
CryptoRF devices are available with EEPROM densities from 1-Kbit to 64-Kbits of user memory to accommodate a wide range of
information storage and cost requirements. The user memory is divided into 4, 8 or 16 separate sections, each of which can be
customized to allow different levels of read and write access, including:
n Free access
n Password protection
n Authentication
n Data encryption and message authentication codes (MACs)
These user selectable optional security features give customers tremendous flexibility in developing and deploying a secure RF
solution. CryptoRF is also deliverable as modules for creation of complete RFID tags, RFID cards and thinned wafers.
Highlights: Stream encryption ensuring data privacy, multiple key sets for authentication and encryption, encrypted passwords with
attempt counters, selectable access rights by zone, tamper sensors, compliant with industry standards.
Advantages of Using Epoxy Glass: High reliability, long life (10 years or more in most applications), corrosion and moisture
resistant.
CryptoRF supports the most stringent security standards used for track and trace, logistics
management, anti-cloning and anti-counterfeiting, identification, and e-purse.
CryptoRF® World’s Largest Family of Secure RF Memories
ELECTRICAL
Parameter Typical Value Units
Resonance Frequency, f0 14.0 MHz
Write Endurance 100,000 Cycles
Data Retention 10 Years
Parameter Typical Value Units
Resonance Frequency, f0 14.5 MHz
Write Endurance 100,000 Cycles
Data Retention 10 Years
MECHANICAL
Parameter Typical Value Units
Substrate Epoxy Glass -
Substrate Thickness 110 µm
Track Cu with Ni+Au plating -
Center Hole Diameter 3 mm
Max Operating Distance* 7 to 15 mm
Typical Punched Outer Dimension 17.0 diameter mm
Maximum Thickness 0.6 mm
Parameter Typical Value Units
Substrate Epoxy Glass -
Substrate Thickness 110 µm
Track Cu with Ni+Au plating -
Center Hole Diameter - mm
Max Operating Distance* 5 to 13 mm
Typical Punched Outer Dimension 13.0 x 13.0 mm
Maximum Thickness 0.9 mm
MY1 Epoxy Glass
17mm thin profile round tag transponders
MX1 Epoxy Glass
13mm thin profile square tag transponders
* Communication range is dependent on the reader antenna design.
Delivery Option
35mm Tape
TEMPERATURE
Parameter Range Units
Storage -40° to +85° Celsius
Operating -25° to +70° Celsius
Parameter Range Units
Storage -40° to +85° Celsius
Operating -25° to +70° Celsius
Delivery Option
35mm Tape
© 2009 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, CryptoRF®, and others are the registered trademarks or trademarks of Atmel Corporation. Other terms and
product names may be the trademarks of others.
Atmel Corporation, Colorado Springs, 1150 E. Cheyenne Mtn. Blvd., Colorado Springs CO 80906 USA • Tel: (719) 576-3300 • Fax: (719) 540-1759
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale
of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE
FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING
OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of
the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically
provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
For free samples of the 4k device
contact Atmel sales at
www.atmel.com/contacts
MX1 Epoxy Glass
MY1 Epoxy Glass
8578-SMEM-02/09/500
Catalog Configuration Memory User Memory Zones RF Protocol
AT88SC0104CRF-MX1, AT88SC0104CRF-MY1 2 Kbits 1 Kbit 4 ISO/IEC 14443 Type B
AT88SC0204CRF-MX1, AT88SC0404CRF-MY1 2 Kbits 2 Kbit 4 ISO/IEC 14443 Type B
AT88SC0404CRF-MX1, AT88SC0404CRF-MY1 2 Kbits 4 Kbit 4 ISO/IEC 14443 Type B
AT88SC0808CRF-MX1, AT88SC0808CRF-MY1 2 Kbits 8 Kbit 8 ISO/IEC 14443 Type B
AT88SC1616CRF-MX1, AT88SC1616CRF-MY1 2 Kbits 16 Kbit 16 ISO/IEC 14443 Type B
AT88SC3216CRF-MX1, AT88SC3216CRF-MY1 2 Kbits 32 Kbit 16 ISO/IEC 14443 Type B
AT88SC6416CRF-MX1, AT88SC6416CRF-MY1 2 Kbits 64 Kbit 16 ISO/IEC 14443 Type B
PRODUCTS
Target Applications: Anti-counterfeiting, clone prevention and authentication, IP and brand protection, energy metering and
payments, medical, safety, and security.
CryptoRF is available in many different shapes and sizes. Specially designed CryptoRF tags in a variety of shapes can be developed
for high volume applications.
Delivery Format for MY1 Module Delivery Format for MX1 Module
