CD-700 Complete VCXO Based Phase Lock Loop CD-700 Description The VI CD-700 is a user-configurable crystal based PLL integrated circuit. It includes a digital phase detector, op-amp, VCXO and additional integrated functions for use in digital synchronization applications. Loop filter software is available as well SPICE models for circuit simulation. Features * * * * * * * * * Applications 5 x 7.5 x 2 mm, smallest VCXO PLL available Output Frequencies to 77.76 MHz 5.0 or 3.3 Vdc operation Tri-State Output Holdover on Loss of Signal Alarm VCXO with CMOS outputs 0/70 or -40/85 0C temperature range Hermetically sealed ceramic SMD package Product is compliant to RoHS directive * * * * * * * Frequency Translation Clock Smoothing, Clock Switching NRZ Clock recovery DSLAM, ADM, ATM, Aggregation, Optical Switching/Routing, Base Station Synchronous Ethernet Low jitter PLL's Block Diagram LOS (8) PHO OPN (3) (2) OPOUT VC (1) (16) LOSIN (4) DATAIN (5) CLKIN (6) Phase Detector and LOS RCLK (9) RDATA (10) OPP (15) VCXO OUT1 (13) Optional 2nd divider OUT2 (11) GND VDD (7) (14) HIZ (12) Page 1 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Performance Specifications Table 1. Electrical Performance Parameter Symbol Output Frequency (ordering option) OUT 1, 5.0 V option OUT 1, 3.3 V option Min Typical 1.000 1.000 Supply Voltage1 +5.0 +3.3 VDD Supply Current IDD Output Logic Levels Output Logic High2 Output Logic Low2 VOH VOL 4.5 2.97 5.0 3.3 tR tF Input Logic Levels Input Logic High2 Input Logic Low2 VIH VIL 2.0 Loss of Signal Indication Output Logic High2 Output Logic Low2 VOH VOL 2.5 Nominal Frequency on Loss of Signal Output 1 Output 2 Absolute Pull Range (ordering option) over operating temperure, aging, and power supply variations Units 77.760 77.760 MHz MHz 5.5 3.63 V V 63 mA 0.5 V V 3.0 3.0 ns ns 0.5 V V 0.5 V V 75 75 ppm ppm 40/60 45/55 40/60 % % % 2.5 Output Transition Times Rise Time2 Fall Time2 Symmetry or Duty Cycle3 Out 1 Out 2 RCLK Maximum SYM1 SYM2 RCLK APR 50 80 100 Test Conditions for APR (+5.0 V option) VC 0.5 4.5 V Test Conditions for APR (+3.3 V option) VC 0.3 3.0 V Gain Transfer Kv Phase Detector Gain +5.0 V option +3.3 V option Kv Operating temperature (ordering option) TOP Control Voltage Leakage Current IVCXO ppm Positive 0.53 0.35 rad/V rad/V 0/70 or -40/85 C 1.0 A 1. A 0.01uF and 0.1uF parallel capacitor should be located as close to pin 14 as possible (and grounded). 2. Figure 2 defines these parameters. Figure 3 illustrates the equivalent five gate TTL load and operating conditions under which these parameters are tested and specified. Loads greater than 15 pF will adversely effect rise/fall time as well as symmetry. 3. Symmetry is defined as (ON TIME/PERIOD with Vs=1.4 V for both 5.0 V and 3.3 V operation. Figure 2. Output Waveform Figure 3. OUT1, OUT2, RCLK, RDATA Test Conditions (25 50C) Page 2 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 2. Absolute Maximum Ratings Parameter Power Supply Storage Temperature Soldering Temperature/Duration Clock and Data Input Range Symbol Ratings Unit VDD 7 Vdc Tstorage -55/125 0C TPEAK / tP 260 / 40 0C/sec CLKIN, DATAIN Gnd-0.5 to VDD +0.5 V Reliability The CD-700 is capable of meeting the following qualification tests: Table 3. Environmental Compliance Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002 Mechanical Vibration MIL-STD-883, Method 2007 Solderability MIL-STD-883, Method 2003 Gross and Fine Leak MIL-STD-883, Method 1014, 100% Tested Resistance to Solvents MIL-STD-883, Method 2016 Handling Precautions Although ESD protection circuitry has been designed into the the CD-700, proper precautions should be taken when handling and mounting. VI employs a Human Body Model (HBM) and a Charged Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Table 4. Predicted ESD R$atings Minimum Conditions Human Body Model Model 1500 V MIL-STD 883, Method 3015 Charged Device Model 1000 V JESD 22-C101 Page 3 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 CD-700 Theory of Operation Phase Detector The phase detector has two buffered inputs (DATAIN and CLKIN) which are designed to switch at 1.4 volts. DATAIN is designed to accept an NRZ data stream but may also be used for clock signals which have a 50% duty cycle. CLKIN is connected to OUT1 or OUT2, or a divided version of one of these outputs. CLKIN and DATAIN and are protected by ESD diodes and should not exceed the power supply voltage or ground by more than a few hundred millivolts. The phase detector is basically a latched flip flop/exclusive-or gate/differential amplifier filter design to produce a DC signal proportional to the phase between the CLKIN and DATAIN signals (see Figure 4 for a block diagram and Figure 5 for an open loop transfer curve). This will simplify the PLL design as the designer does not have to filter narrow pulse signals to a DC level. Under locked conditions the rising edge of CLKIN will be centered in the middle of the DATAIN signal (see Figure 6). The phase detector gain is 0.53V/rad x data density for 5volt operation and 0.35V/rad x data density for 3.3 volt operation. Data density is equal to 1.0 for clock signals and is system dependent on coding and design for NRZ signals, but 0.25 could be used as a starting point for data density. The phase detector output is a DC signal for DATAIN frequencies greater than 1 MHz but produces significant ripple when inputs are less than 200 kHz. Additional filtering is required for lower input frequencies applications such as 8kHz (see Figures 8 and 9 as examples). Figure 4. Simplified Phase Detector Block Diagram Under closed loop conditions the active filter has a blocking capacitor which provides a very high DC gain, so under normal locked conditions and input frequencies >1 MHz, PHO will be about VDD/2 and will not vary significantly with changes in input frequency (within lock range). The control voltage (pin 16) will vary according to the input frequency offset, but PHO will remain relatively constant. Recovered Clock and Data Alignment Outputs The CD-700 is designed to recover an embedded clock from an NRZ data signal and retime it with a data pattern. In this application, the VCXO frequency is exactly the same frequency as the NRZ data rate and the outputs are taken off Pin 9 (RCLK), and Pin 10 (RDATA). Under locked conditions, the falling edge of RCLK is centered in the RDATA pattern. Also, there is a 1.5 clock cycle delay between DATAIN and RDATA. Figure 6 shows the relationship between the DATAIN, CLKIN, RDATA and RCLK. Figure 5. Open Loop Phase Detecto Transfer Curve Figure 6. Clock and Data Timing Relationships for the NRZ data Other RZ encoding schemes such as Manchester or AMI can be accomodated by using a CD-700 at twice the baud rate. Page 4 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Loss of Signal, LOS and LOSIN The LOS circuit provides an output alarm flag when the DATAIN input signal is lost. The LOS output is normally a logic low and is set to a logic high after 256 consecutive clock periods on CLKIN with no detected DATAIN transitions. This signal can be used to either flag external alarm circuits and/or drive the CD-700's LOSIN input. When LOSIN is set to a logic high, the VCXO control voltage (pin 16) is switched to an internal voltage which sets OUT1 and OUT2 to center frequency +/-75ppm. Also, LOS automatically closes the op amp feedback which means the op-amp is a unity gain buffer and will produce a DC voltage equal to the +op amp voltage (pin 15), usually VDD/2. VCXO and Absolute Pull Range (APR) Specification The CD-700's VCXO is a varactor tuned crystal oscillator, which produces an output frequency proportional to the control voltage (pin 16). The frequency deviation of the CD-700 VCXO is specified in terms of Absolute Pull Range (APR). APR provides the user with a guaranteed specification for minimum available frequency deviation over all operating conditions. Operating conditions include power supply variation, operating temperature range, and differences in output loading and changes due to aging. A CD-700 VCXO with an APR of +/-50 ppm will track a +/-50 ppm reference source over all operating conditions. The fourth character of the product code in Table 7 specifies absolute Pull Range (APR). Please see Vectron's web site (www.vectron.com) for the APR Application Note. APR is tested at 0.5 and 4.5 volts for the 5.0 volt option and 0.3 and 3.0 volts for the 3.3 volt option. VCXO Aging Quartz oscillators typically exhibit a part per million shift in output frequency during aging. The major factors, which lead to this shift, are changes in the mechanical stress on the crystal and mass-loading on the crystal. As the oscillator ages, relaxation of the crystal mounting stress or transfer of environmental stress through the package to the crystal mounting arrangement can lead to frequency variations. VI has minimized these two effects through the use of a miniature AT-cut strip resonator crystal which allows a superior mounting arrangement. This results in minimal relaxation and almost negligible environmental stress transfer. VI has eliminated the impact of mass loading by ensuring hermetic integrity and minimizing out-gassing by limiting the number of internal components through the use of ASIC technology. Mass-loading on the crystal generally results in a frequency decrease and is typically due to out-gassing of material within a hermetic package or from contamination by external material in a nonhermetic package. Under normal operating conditions the CD-700 will typically exhibit 2 ppm aging in the first year of operation. The device will then typically exhibit 1 ppm aging the following year with a logarithmic decline each year thereafter. Frequency Divider Feature The lowest available VCXO OUT1 frequency is 1.000 MHz. To achieve lower frequencies, OUT1 is divided by a 2n counter (n = 1 to 8) and is the OUT2 frequency. The divider values (2, 4, 8, 16, 32, 64, 128 and 256) are set at the factory, so it is user selectable upon ordering only. In addition, a disabled OUT2 option is also available. To achieve 1.024 MHz, a CD-700 with OUT1 frequency equal to 16.384 MHz and a divider value equal to 16 would be used. Additional external divider circuits can be used to further lower or change the frequency. Loop Filter A PLL is a feedback system which forces the output frequency to lock in both phase and frequency to the input frequency. While there will be some phase error, theory states there is no frequency error. The loop filter design will dictate many key parameters such as jitter reduction, stability, lock range and acquisition time. Be advised that many textbook equations describing loop dynamics, such as capture range are based on ideal systems. Such equations may not be accurate for real systems due to nonlinearities, DC offsets, noise and do not take into account the limited VCXO bandwidth. This section deals with some real world design examples. Also, there is loop filter software on the Vectron web site, plus a full staff of experienced applications engineers who are eager to assist in this process. Common CD-700 PLL applications are shown in Figures 8, 9 (frequency translation), Figure 10 (clock recovery) and Figure 11 (clock smoothing). Page 5 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Of primary concern to the designer is selecting a loop filter that insures lock-in, stability and provides adequate filtering of the input signal. For low input frequencies, a good starting point for the loop filter bandwidth is 10 Hz (typical). An example would be translating an 8 kHz signal to 44.736 MHz. Figures 8 and 9 show 8kHz to 44.736 MHz and 8kHz to 19.440 MHz frequency translation designs. For high input frequencies, a good starting point for the loop filter bandwidth is 100 ppm times the input frequency. It's fairly easy to set a low loop bandwidth for large frequency translations such as 8kHz to 44.736MHz, but becomes more difficult for clock smoothing applications such as 19.440 MHz input and 19.440MHz output. In this example, 100ppm * 19.440MHz is approximately 2kHz and this loop filter bandwidth may be too high to adequately reject jitter. A good way to resolve this is to lower the DATAIN frequency such as dividing the input frequency down. The loop filter bandwidth becomes lower since 100ppm * DATAIN is lowered. Figure 11 shows an example for clock smoothing on a relatively high input frequency signal and maintaining a wide lock range. There is no known accurate formula for calculating acquisition time and so the best way to provide realisitc figures is to measure the lock time for a CD-700. By measuring the control voltage settling time, acquisiton time was measured in the range of 3-5 seconds for applications such as 8kHz to 34.368 MHz frequency translation which is similar to the application in Figures 8 and 9, to sub 10 milliseconds for NRZ data patterns such as Figure 10. It may be tempting to reduce the damping factor to 0.7 or 1.0 in order to improve acquisition time; but, it degrades stability and will not signifigantly improve acquisition time. A damping factor of 4 is fairly conservative and allows for excellent stability. Some general quidelines for selecting the loop filter elements include: Values should be less than 1Megohm and at least 10kohm between the PHO and OPN, the capacitor should be low leakage and a polarized capacitor is acceptable, the R/C's should be located physically close to the CD-700 .The loop filter software available on the web site was written for 5 volt operation. A simple way to calculate values for 3.3 volt operation is to multiply the data density by 0.66 (3.3V / 5V). SPICE models are another design aid. In most cases a new PLL CD-700 design is calculated by using the software and verified with SPICE models. The simple active SPICE model is shown in Figure 7. Loop filter values can be modified to suit the system requirements and application. There are many excellent references on designing PLL's, such as "Phase-Locked Loops, Theory, Design and Applications", by Roland E Best (McGraw-Hill). Figure 7. SPICE Model *****CD-700 ac Loop model vi 1 0 ac 1 ri 1 0 1k *****Phase Detector e1 2 0 1 0 1 (for closed loop response use: e1 2 0 1 12 1) r2 2 3 30k c1 3 0 60p *****Phase Detector Gain=0.53 x Data Density (Data Density = 1 for clocks) for 5 volt operation and = 0.35 x Data Density for 3.3 volt operation e2 4 0 3 0 .35 *****Loop filter r1 4 5 60k c2 5 0 10p rf 5 6 90k cf 6 7 1.0u e3 7 0 5 0 -10000 Page 6 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 ***** VCXO, Input Bandwidth=50kHz r5 7 8 160k c4 8 0 20p *****VCXO Gain x 2 (Example: 19.440 MHz x 100 ppm x 2 x ) e4 9 0 8 0 12214 *****1/S model r6 9 10 1000 c5 10 11 0.001u e5 11 0 10 0 -1e6 ****Divide by n e6 12 0 11 0 1 r7 12 0 1k The bold numbers are user selectable R and C values that will vary depending on the application (see Figure 11). Layout Considerations To achieve stable, low noise performance good analog layout techniques should be incorporated and a partial list is shown below. The CD-700 should be treated more like an analog device and the power supply must be well decoupled with a good quality RF 0.01 uF capacitor in parallel with a 0.1 uF capacitor, located as close to pin 14 as possible and connected to ground. In some cases, a PI filter such as a large capacitor (10uF) to ground, a series ferrite bead or inductor with 0.01 uF and 100 pF capacitor to ground to decouple the device supply. The traces for the OUT1, OUT2, RCLK and RDATA ouputs should be kept as short as possible. It is common practice to use a series resistor ( 50 to 100 ohms ) in order to reduce reflections if these traces are more than a couple of inches long. Also OUT1, OUT2, RCLK and RDATA should not be routed directly underneath the device. The op-amp loop filter components should be kept as close to the device as possible and the feedback capacitor should be located close to the op-amp input terminal. The loop filter capacitor(s) should be low leakage (polarized capacitors are allowed). Unused outputs should be left floating and it is not required to load or terminate them (such as an ECL or PECL output). Loading unused outputs will only increase current consumption. Application Circuits Figure 8. 8kHz to 44.736MHz Frequency Translation Page 7 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Figure 9. 8kHz to 19.44MHz Frequency Translation Figure 10. 40.00MHz NRZ CLock Recovery Figure 11. 19.44MHz CLock Smoothing Page 8 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Table 5. Environmental Compliance Parameter Symbol Value PreHeat Time tS 60 sec Min, 180 sec Max Ramp Up RUP 3 0C/sec Max tL 60 sec Min, 150 sec Max tAMP-B 480 sec Max tP 20 sec Min, 40 sec Max RDN 6 0C/sec Max Time Above 217 oC Time To Peak Temperature Time At 260 oC Ramp Down The device has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements. The temperatures refer to the topside of the package, measured on the package body surface. The CD-700 device is hermetically sealed so an aqueous wash is not an issue. Figure 12. Suggested IR Profile Tape and Reel Figure 13. Tape and Reel Table 6. Tape and Reel Information Tape Dimensions (mm) Reel Dimensions (mm) A B C D E F G H I J K L #/Reel 16 7.5 1.5 4 8 1.5 20.2 13 50 6 16.4 178 200 Page 9 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Figure 14. Outline Diagram Table 7. Pin Functions Pin Symbol Function 1 OPOUT 2 OPN Op-Amp Negative Input 3 PHO Phase detector Output 4 LOSIN 5 DATAIN Phase detector Input signal (TTL switching thresholds) 6 CLKIN Phase detector Clock signal (TTL switching thresholds) 7 GND Cover and Electrical Ground 8 LOS OUTPUT (Used with LOSIN) Logic 1 if there are no transitions detected at DATAIN after 256 clock cycles at CLKIN. As soon as a transition occurs at DATAIN, LOS is set to a logic low. Logic 0 = Input frequency detected 9 RCLK Recovered Clock 10 RDATA Recovered Data 11 OUT2 Divided-down VCXO Output, or Disabled 12 HIZ 13 OUT1 14 VDD Power Supply Voltage (3.3 V 10% or 5.0 V 10%) 15 OPP Op-Amp Positive Input 16 VC VCXO Control Voltage Op-Amp Output INPUT (Used with LOS) Logic 0, VCXO control voltage is enabled. Logic 1, VCXO control voltage (pin 16) is disabled and OUT1 and OUT2 are within +/-75 ppm of center frequency Has Internal pull-down resistor INPUT Logic 0, OUT1, OUT2, RCLK, RDATA are set to a high impedance state. Logic 1, OUT1, OUT2, RCLK, RDATA are active. Has Internal pull-up resistor VCXO Output Page 10 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Table 8. Standard OUT1 Frequencies (MHz) 12M2880000 19M2000000 21M0050840 29M4912000 38M8800000 44M4343000 52M0000000 70M0000000 12M3076860 19M3926580 22M0000000 29M5000000 39M0625000 44M6218000 53M3300000 70M6560000 12M3520000 19M4400000 22M1047720 30M0000000 39M3216000 44M7360000 54M7460000 71M6100000 12M8000000 19M5312500 22M2171000 30M7200000 39M8437500 44M9280000 55M0000000 73M7280000 13M0000000 19M6608000 22M5792000 30M8800000 40M0000000 45M1584000 60M0000000 74M1250000 13M5000000 19M6989680 24M0000000 31M2500000 40M2830630 45M8240000 61M3800000 74M1758000 14M8351600 19M7190000 24M5760000 32M0000000 40M9600000 46M0379460 61M4400000 74M2500000 15M0000000 19M9218750 24M7040000 32M7680000 41M0888870 46M7200000 62M2080000 75M0000000 15M0336000 20M0000000 25M0000000 33M0000000 41M6571440 46M8750000 62M5000000 76M8000000 15M3600000 20M1416000 25M1658000 33M3330000 41M6600000 48M0000000 62M9145000 77M7600000 16M0000000 20M4800000 25M6000000 34M3680000 41M8329130 49M1520000 63M3600000 16M3840000 20M5444340 25M9200000 34M5600000 42M0000000 49M4080000 63M8976000 17M1840000 20M7135000 26M0000000 36M8640000 42M0101690 50M0000000 64M0000000 18M4320000 20M8285720 27M0000000 37M0560000 42M5000000 50M0480000 64M1520000 18M5280000 20M8286000 27M6480000 37M1250000 42M6600000 51M2000000 65M5360000 Page 11 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009 Ordering Information CD - 700 - D A E - K A N N - xxMxxxxxxx Product Family CD: Clock and Data Recovery Frequency (See Above) Package 700: 5.0 x 7.5 x 2.0mm Performance Options N: Standard A: Improved Phase Noise Input D: 5.0 Vdc 10% E: 3.3 Vdc 10% Factory Use Output A: CMOS/HCMOS/ACMOS Output 2 Divider A: Divide by 2 B: Divide by 4 C: Divide by 8 D: Divide by 16 E: Divide by 32 F: Divide by 64 G: Divide by 128 H: Divide by 256 K: Disabled Operating Temperature E: -40 to 85 C T: 0 to 70 C Absolute Pull Range K: 50 ppm S: 100 ppm Note: Not all combinations are available. Check with the factory for the optimum device configuration for your application For Additional Information, Please Contact USA: Europe: Asia: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Page 12 of 12 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Rev: 30Mar2009