LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
1.5V, SC70, Multi-Gain Analog Temperature Sensor with Class-AB Output
Check for Samples: LM94022
1FEATURES DESCRIPTION
The LM94022 is a precision analog output CMOS
2• LM94022Q is AEC-Q100 Grade 0 qualified and integrated-circuit temperature sensor that operates at
is Manufactured on an Automotive Grade Flow a supply voltage as low as 1.5 Volts. A class-AB
• Low 1.5V Operation output structure gives the LM94022 strong output
• Push-Pull Output with 50µA Source Current source and sink current capability for driving heavy
loads. For example, it is well suited to source the
Capability input of a sample-and-hold analog-to-digital converter
• Four Selectable Gains with its transient load requirements. While operating
• Very Accurate Over Wide Temperature Range over the wide temperature range of −50°C to +150°C,
of −50°C to +150°C the LM94022 delivers an output voltage that is
inversely proportional to measured temperature. The
• Low Quiescent Current LM94022's low supply current makes it ideal for
• Output is Short-Circuit Protected battery-powered systems as well as general
• Extremely Small SC70 Package temperature sensing applications.
• Footprint Compatible with the Industry- Two logic inputs, Gain Select 1 (GS1) and Gain
Standard LM20 Temperature Sensor Select 0 (GS0), select the gain of the temperature-to-
voltage output transfer function. Four slopes are
APPLICATIONS selectable: −5.5 mV/°C, −8.2 mV/°C, −10.9 mV/°C,
and −13.6 mV/°C. In the lowest gain configuration
• Cell phones (GS1 and GS0 both tied low), the LM94022 can
• Wireless Transceivers operate with a 1.5V supply while measuring
• Battery Management temperature over the full −50°C to +150°C operating
range. Tying both inputs high causes the transfer
• Automotive function to have the largest gain of −13.6 mV/°C for
• Disk Drives maximum temperature sensitivity. The gain-select
• Games inputs can be tied directly to VDD or Ground without
any pull-up or pull-down resistors, reducing
• Appliances component count and board area. These inputs can
also be driven by logic signals allowing the system to
optimize the gain during operation or system
diagnostics.
KEY SPECIFICATIONS
VALUE UNIT
Supply Voltage 1.5 to 5.5 V
Supply Current 5.4 μA (typ)
Output Drive ±50 μA
20°C to 40°C ±1.5
–50°C to 70°C ±1.8
Temperature Accuracy °C
–50°C to 90°C ±2.1
–50°C to 150°C ±2.7
Operating Temperature −50 to 150 °C
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2006–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Single Battery
Cell
VDD (+1.5V to +5.5V)
LM94022
GND
OUT
VDD
GS1
GS0
LM94022
GND
OUT VDD
GS1
GS0
4
51
2
3
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
CONNECTION DIAGRAM
Figure 1. SC70-5 Top View
See Package Number DCK0005A
TYPICAL TRANSFER CHARACTERISTIC
Output Voltage vs Temperature
TYPICAL APPLICATION
Full-Range Celsius Temperature Sensor (−50°C to +150°C) Operating from a Single Battery Cell
2Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
VDD
GND
VDD
GND
ESD
CLAMP
LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
PIN DESCRIPTIONS
PIN
LABEL TYPE EQUIVALENT CIRCUIT FUNCTION
NUMBER
GS1 5 Logic Input Gain Select 1 - One of two inputs for selecting the
slope of the output response
GS0 1 Logic Input Gain Select 0 - One of two inputs for selecting the
slope of the output response
OUT 3 Analog Output Outputs a voltage which is inversely proportional to
temperature
VDD 4 Power Positive Supply Voltage
GND 2 Ground Power Supply Ground
ABSOLUTE MAXIMUM RATINGS (1)
VALUE UNIT
Supply Voltage −0.3 to +6.0 V
Voltage at Output Pin −0.3 to (VDD + 0.5) V
Output Current ±7 mA
Voltage at GS0 and GS1 Input Pins −0.3 to +6.0 V
Input Current at any pin (2) 5 mA
Storage Temperature −65 to +150 °C
Maximum Junction Temperature (TJMAX) +150 °C
Human Body Model 2500 V
ESD Susceptibility (3) :Machine Model 250 V
Soldering process must comply with Reflow Temperature Profile specifications. Refer to http://www.ti.com/packaging(4)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see
the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics
may degrade when the device is not operated under the listed test conditions.
(2) When the input voltage (VI) at any pin exceeds power supplies (VI< GND or VI> V+), the current at that pin should be limited to 5 mA.
(3) The human body model is a 100 pF capacitor discharged through a 1.5 kΩresistor into each pin. The machine model is a 200 pF
capacitor discharged directly into each pin.
(4) Reflow temperature profiles are different for lead-free and non-lead-free packages.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM94022
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
OPERATING RATINGS (1)
VALUE UNIT
Specified Temperature Range: TMIN ≤TA≤TMAX °C
LM94022 −50 ≤TA≤+150 °C
Supply Voltage Range (VDD) +1.5 to +5.5 V
Thermal Resistance (θJA)(2)(3)
SC70 415 °C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see
the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics
may degrade when the device is not operated under the listed test conditions.
(2) The junction to ambient thermal resistance (θJA) is specified without a heat sink in still air.
(3) Changes in output due to self heating can be computed by multiplying the internal dissipation by the thermal resistance.
ACCURACY CHARACTERISTICS
These limits do not include DC load regulation. These stated accuracy limits are with reference to the values in the LM94022
Transfer Table. UNITS
PARAMETER CONDITIONS LIMITS (1) (LIMIT)
TA= +20°C to +40°C; VDD = 1.5V to 5.5V ±1.5 °C (max)
TA= +0°C to +70°C; VDD = 1.5V to 5.5V ±1.8 °C (max)
TA= +0°C to +90°C; VDD = 1.5V to 5.5V ±2.1 °C (max)
GS1=0
GS0=0 TA= +0°C to +120°C; VDD = 1.5V to 5.5V ±2.4 °C (max)
TA= +0°C to +150°C; VDD = 1.5V to 5.5V ±2.7 °C (max)
TA=−50°C to +0°C; VDD = 1.6V to 5.5V ±1.8 °C (max)
TA= +20°C to +40°C; VDD = 1.8V to 5.5V ±1.5 °C (max)
TA= +0°C to +70°C; VDD = 1.9V to 5.5V ±1.8 °C (max)
TA= +0°C to +90°C; VDD = 1.9V to 5.5V ±2.1 °C (max)
GS1=0
GS0=1 TA= +0°C to +120°C; VDD = 1.9V to 5.5V ±2.4 °C (max)
TA= +0°C to +150°C; VDD = 1.9V to 5.5V ±2.7 °C (max)
TA=−50°C to +0°C; VDD = 2.3V to 5.5V ±1.8 °C (max)
Temperature Error (2) TA= +20°C to +40°C; VDD = 2.2V to 5.5V ±1.5 °C (max)
TA= +0°C to +70°C; VDD = 2.4V to 5.5V ±1.8 °C (max)
TA= +0°C to +90°C; VDD = 2.4V to 5.5V ±2.1 °C (max)
GS1=1
GS0=0 TA= +0°C to +120°C; VDD = 2.4V to 5.5V ±2.4 °C (max)
TA= +0°C to +150°C; VDD = 2.4V to 5.5V ±2.7 °C (max)
TA=−50°C to +0°C; VDD = 3.0V to 5.5V ±1.8 °C (max)
TA= +20°C to +40°C; VDD = 2.7V to 5.5V ±1.5 °C (max)
TA= +0°C to +70°C; VDD = 3.0V to 5.5V ±1.8 °C (max)
TA= +0°C to +90°C; VDD = 3.0V to 5.5V ±2.1 °C (max)
GS1=1
GS0=1 TA= +0°C to +120°C; VDD = 3.0V to 5.5V ±2.4 °C (max)
TA= 0°C to +150°C; VDD = 3.0V to 5.5V ±2.7 °C (max)
TA=−50°C to +0°C; VDD = 3.6V to 5.5V ±1.8 °C (max)
(1) Limits are guaranteed to TI's AOQL (Average Outgoing Quality Level).
(2) Accuracy is defined as the error between the measured and reference output voltages, tabulated in the Transfer Table at the specified
conditions of supply gain setting, voltage, and temperature (expressed in °C). Accuracy limits include line regulation within the specified
conditions. Accuracy limits do not include load regulation; they assume no DC load.
4Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
ELECTRICAL CHARACTERISTICS
Unless otherwise noted, these specifications apply for +VDD = +1.5V to +5.5V. Boldface limits apply for TA= TJ= TMIN to
TMAX ; all other limits TA= TJ= 25°C. UNITS
PARAMETER CONDITIONS TYPICAL (1) LIMITS (2) (LIMIT)
GS1 = 0, GS0 = 0 –5.5 mV/°C
GS1 = 0, GS1 = 1 –8.2 mV/°C
Sensor Gain GS1 = 1, GS0 = 0 –10.9 mV/°C
GS1 = 1, GS0 = 1 –13.6 mV/°C
Source ≤50 μA, (VDD - VOUT)≥200mV –0.22 –1 mV (max)
Load Regulation (3) Sink ≤50 μA, VOUT ≥200mV 0.26 1mV (max)
Line Regulation (4) 200 μV/V
ISTA= +30°C to +150°C, (VDD - VOUT)≥5.4 8.1 μA (max)
100mV
Supply Current TA= -50°C to +150°C, (VDD - VOUT)≥5.4 9μA (max)
100mV
CLOutput Load Capacitance 1100 pF (max)
Power-on Time (5) CL= 0 pF to 1100 pF 0.7 1.9 ms (max)
VIH GS1 and GS0 Input Logic "1" VDD– 0.5V V (min)
Threshold Voltage
VIL GS1 and GS0 Input Logic "0" 0.5 V (max)
Threshold Voltage
IIH Logic "1" Input Current (6) 0.001 1μA (max)
IIL Logic "0" Input Current (6) 0.001 1μA (max)
(1) Typicals are at TJ= TA= 25°C and represent most likely parametric norm.
(2) Limits are guaranteed to TI's AOQL (Average Outgoing Quality Level).
(3) Source currents are flowing out of the LM94022. Sink currents are flowing into the LM94022.
(4) Line regulation (DC) is calculated by subtracting the output voltage at the highest supply voltage from the output voltage at the lowest
supply voltage. The typical DC line regulation specification does not include the output voltage shift discussed in OUTPUT VOLTAGE
SHIFT.
(5) Guaranteed by design and characterization.
(6) The input current is leakage only and is highest at high temperature. It is typically only 0.001µA. The 1µA limit is solely based on a
testing limitation and does not reflect the actual performance of the part.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM94022
-50 -25 0 25 50 75 100 125 150
TEMPERATURE (ºC)
-4
-3
-2
-1
0
1
2
3
4
TEMPERATURE ERROR (ºC)
MIN Limit
MAX Limit
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
Temperature Error vs. Temperature Minimum Operating Temperature vs. Supply Voltage
Figure 2. Figure 3.
Supply Current vs. Temperature Supply Current vs. Supply Voltage
Figure 4. Figure 5.
Load Regulation, Sourcing Current Load Regulation, Sinking Current
Figure 6. Figure 7.
6Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Change in Vout vs. Overhead Voltage Supply-Noise Gain vs. Frequency
Figure 8. Figure 9.
Output Voltage vs. Supply Voltage Output Voltage vs. Supply Voltage
Gain Select = 00 Gain Select = 01
Figure 10. Figure 11.
Output Voltage vs. Supply Voltage Output Voltage vs. Supply Voltage
Gain Select = 10 Gain Select = 11
Figure 12. Figure 13.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM94022
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
LM94022 TRANSFER FUNCTION
The LM94022 has four selectable gains, each of which can be selected by the GS1 and GS0 input pins. The
output voltage for each gain, across the complete operating temperature range is shown in Table 1. This table is
the reference from which the LM94022 accuracy specifications (listed in the ELECTRICAL CHARACTERISTICS
section) are determined. This table can be used, for example, in a host processor look-up table. A file containing
this data is available for download at http://www.ti.com/lsds/ti/analog/temperature_sensor.page.
Table 1. LM94022 Transfer Table
TEMPERATURE GS = 00 GS = 01 GS = 10 GS = 11
(°C) (mV) (mV) (mV) (mV)
-50 1299 1955 2616 3277
-49 1294 1949 2607 3266
-48 1289 1942 2598 3254
-47 1284 1935 2589 3243
-46 1278 1928 2580 3232
-45 1273 1921 2571 3221
-44 1268 1915 2562 3210
-43 1263 1908 2553 3199
-42 1257 1900 2543 3186
-41 1252 1892 2533 3173
-40 1247 1885 2522 3160
-39 1242 1877 2512 3147
-38 1236 1869 2501 3134
-37 1231 1861 2491 3121
-36 1226 1853 2481 3108
-35 1221 1845 2470 3095
-34 1215 1838 2460 3082
-33 1210 1830 2449 3069
-32 1205 1822 2439 3056
-31 1200 1814 2429 3043
-30 1194 1806 2418 3030
-29 1189 1798 2408 3017
-28 1184 1790 2397 3004
-27 1178 1783 2387 2991
-26 1173 1775 2376 2978
-25 1168 1767 2366 2965
-24 1162 1759 2355 2952
-23 1157 1751 2345 2938
-22 1152 1743 2334 2925
-21 1146 1735 2324 2912
-20 1141 1727 2313 2899
-19 1136 1719 2302 2886
-18 1130 1711 2292 2873
-17 1125 1703 2281 2859
-16 1120 1695 2271 2846
-15 1114 1687 2260 2833
-14 1109 1679 2250 2820
-13 1104 1671 2239 2807
-12 1098 1663 2228 2793
8Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
Table 1. LM94022 Transfer Table (continued)
TEMPERATURE GS = 00 GS = 01 GS = 10 GS = 11
(°C) (mV) (mV) (mV) (mV)
-11 1093 1656 2218 2780
-10 1088 1648 2207 2767
-9 1082 1639 2197 2754
-8 1077 1631 2186 2740
-7 1072 1623 2175 2727
-6 1066 1615 2164 2714
-5 1061 1607 2154 2700
-4 1055 1599 2143 2687
-3 1050 1591 2132 2674
-2 1044 1583 2122 2660
-1 1039 1575 2111 2647
0 1034 1567 2100 2633
1 1028 1559 2089 2620
2 1023 1551 2079 2607
3 1017 1543 2068 2593
4 1012 1535 2057 2580
5 1007 1527 2047 2567
6 1001 1519 2036 2553
7 996 1511 2025 2540
8 990 1502 2014 2527
9 985 1494 2004 2513
10 980 1486 1993 2500
11 974 1478 1982 2486
12 969 1470 1971 2473
13 963 1462 1961 2459
14 958 1454 1950 2446
15 952 1446 1939 2433
16 947 1438 1928 2419
17 941 1430 1918 2406
18 936 1421 1907 2392
19 931 1413 1896 2379
20 925 1405 1885 2365
21 920 1397 1874 2352
22 914 1389 1864 2338
23 909 1381 1853 2325
24 903 1373 1842 2311
25 898 1365 1831 2298
26 892 1356 1820 2285
27 887 1348 1810 2271
28 882 1340 1799 2258
29 876 1332 1788 2244
30 871 1324 1777 2231
31 865 1316 1766 2217
32 860 1308 1756 2204
33 854 1299 1745 2190
34 849 1291 1734 2176
35 843 1283 1723 2163
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM94022
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
Table 1. LM94022 Transfer Table (continued)
TEMPERATURE GS = 00 GS = 01 GS = 10 GS = 11
(°C) (mV) (mV) (mV) (mV)
36 838 1275 1712 2149
37 832 1267 1701 2136
38 827 1258 1690 2122
39 821 1250 1679 2108
40 816 1242 1668 2095
41 810 1234 1657 2081
42 804 1225 1646 2067
43 799 1217 1635 2054
44 793 1209 1624 2040
45 788 1201 1613 2026
46 782 1192 1602 2012
47 777 1184 1591 1999
48 771 1176 1580 1985
49 766 1167 1569 1971
50 760 1159 1558 1958
51 754 1151 1547 1944
52 749 1143 1536 1930
53 743 1134 1525 1916
54 738 1126 1514 1902
55 732 1118 1503 1888
56 726 1109 1492 1875
57 721 1101 1481 1861
58 715 1093 1470 1847
59 710 1084 1459 1833
60 704 1076 1448 1819
61 698 1067 1436 1805
62 693 1059 1425 1791
63 687 1051 1414 1777
64 681 1042 1403 1763
65 676 1034 1391 1749
66 670 1025 1380 1735
67 664 1017 1369 1721
68 659 1008 1358 1707
69 653 1000 1346 1693
70 647 991 1335 1679
71 642 983 1324 1665
72 636 974 1313 1651
73 630 966 1301 1637
74 625 957 1290 1623
75 619 949 1279 1609
76 613 941 1268 1595
77 608 932 1257 1581
78 602 924 1245 1567
79 596 915 1234 1553
80 591 907 1223 1539
81 585 898 1212 1525
82 579 890 1201 1511
10 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
Table 1. LM94022 Transfer Table (continued)
TEMPERATURE GS = 00 GS = 01 GS = 10 GS = 11
(°C) (mV) (mV) (mV) (mV)
83 574 881 1189 1497
84 568 873 1178 1483
85 562 865 1167 1469
86 557 856 1155 1455
87 551 848 1144 1441
88 545 839 1133 1427
89 539 831 1122 1413
90 534 822 1110 1399
91 528 814 1099 1385
92 522 805 1088 1371
93 517 797 1076 1356
94 511 788 1065 1342
95 505 779 1054 1328
96 499 771 1042 1314
97 494 762 1031 1300
98 488 754 1020 1286
99 482 745 1008 1272
100 476 737 997 1257
101 471 728 986 1243
102 465 720 974 1229
103 459 711 963 1215
104 453 702 951 1201
105 448 694 940 1186
106 442 685 929 1172
107 436 677 917 1158
108 430 668 906 1144
109 425 660 895 1130
110 419 651 883 1115
111 413 642 872 1101
112 407 634 860 1087
113 401 625 849 1073
114 396 617 837 1058
115 390 608 826 1044
116 384 599 814 1030
117 378 591 803 1015
118 372 582 791 1001
119 367 573 780 987
120 361 565 769 973
121 355 556 757 958
122 349 547 745 944
123 343 539 734 929
124 337 530 722 915
125 332 521 711 901
126 326 513 699 886
127 320 504 688 872
128 314 495 676 858
129 308 487 665 843
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM94022
(-5.50 mV / oC) u
V = T + 1035 mV
(-5.50 mV / oC)u
V - 925 mV = (T - 20oC)
760 mV - 925 mV
50oC - 20oCu
¹
·
¹
·
V - 925 mV = (T - 20oC)
V2 - V1
T2 - T1u
¹
·
¹
·
V - V1 = (T - T1)
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
Table 1. LM94022 Transfer Table (continued)
TEMPERATURE GS = 00 GS = 01 GS = 10 GS = 11
(°C) (mV) (mV) (mV) (mV)
130 302 478 653 829
131 296 469 642 814
132 291 460 630 800
133 285 452 618 786
134 279 443 607 771
135 273 434 595 757
136 267 425 584 742
137 261 416 572 728
138 255 408 560 713
139 249 399 549 699
140 243 390 537 684
141 237 381 525 670
142 231 372 514 655
143 225 363 502 640
144 219 354 490 626
145 213 346 479 611
146 207 337 467 597
147 201 328 455 582
148 195 319 443 568
149 189 310 432 553
150 183 301 420 538
Although the LM94022 is very linear, its response does have a slight umbrella's parabolic shape. This shape is
very accurately reflected in Table 1. The Transfer Table can be calculated by using the parabolic equation.
(1)
For a linear approximation, a line can easily be calculated over the desired temperature range from the Table
using the two-point equation:
(2)
Where V is in mV, T is in °C, T1and V1are the coordinates of the lowest temperature, T2and V2are the
coordinates of the highest temperature.
For example, if we want to determine the equation of a line with the Gain Setting at GS1 = 0 and GS0 = 0, over a
temperature range of 20°C to 50°C, we would proceed as follows:
(3)
(4)
(5)
12 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
[ ]
TJ = TA + TJA (VDDIQ) + (VDD - VO) IL
LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
Using this method of linear approximation, the transfer function can be approximated for one or more
temperature ranges of interest.
MOUNTING AND THERMAL CONDUCTIVITY
The LM94022 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be
glued or cemented to a surface.
To ensure good thermal conductivity, the backside of the LM94022 die is directly attached to the GND pin (Pin
2). The temperatures of the lands and traces to the other leads of the LM94022 will also affect the temperature
reading.
Alternatively, the LM94022 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath
or screwed into a threaded hole in a tank. As with any IC, the LM94022 and accompanying wiring and circuits
must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate
at cold temperatures where condensation can occur. If moisture creates a short circuit from the output to ground
or VDD, the output from the LM94022 will not be correct. Printed-circuit coatings are often used to ensure that
moisture cannot corrode the leads or circuit traces.
The thermal resistance junction to ambient (θJA) is the parameter used to calculate the rise of a device junction
temperature due to its power dissipation. The equation used to calculate the rise in the LM94022's die
temperature is:
(6)
where TAis the ambient temperature, IQis the quiescent current, ILis the load current on the output, and VOis the
output voltage. For example, in an application where TA= 30 °C, VDD =5V,IDD =9μA, Gain Select = 11, VOUT =
2.231 mV, and IL=2μA, the junction temperature would be 30.021 °C, showing a self-heating error of only
0.021°C. Since the LM94022's junction temperature is the actual temperature being measured, care should be
taken to minimize the load current that the LM94022 is required to drive. Table 2 shows the thermal resistance of
the LM94022.
Table 2. LM94022 Thermal Resistance
DEVICE NUMBER NS PACKAGE NUMBER THERMAL RESISTANCE (θJA)
LM94022BIMG DCK0005A 415°C/W
OUTPUT AND NOISE CONSIDERATIONS
A push-pull output gives the LM94022 the ability to sink and source significant current. This is beneficial when,
for example, driving dynamic loads like an input stage on an analog-to-digital converter (ADC). In these
applications the source current is required to quickly charge the input capacitor of the ADC. See the
APPLICATION CIRCUITS section for more discussion of this topic. The LM94022 is ideal for this and other
applications which require strong source or sink current.
The LM94022's supply-noise gain (the ratio of the AC signal on VOUT to the AC signal on VDD) was measured
during bench tests. It's typical attenuation is shown in the TYPICAL PERFORMANCE CHARACTERISTICS
section. A load capacitor on the output can help to filter noise.
For operation in very noisy environments, some bypass capacitance should be present on the supply within
approximately 2 inches of the LM94022.
CAPACITIVE LOADS
The LM94022 handles capacitive loading well. In an extremely noisy environment, or when driving a switched
sampling input on an ADC, it may be necessary to add some filtering to minimize noise coupling. Without any
precautions, the LM94022 can drive a capacitive load less than or equal to 1100 pF as shown in Figure 14. For
capacitive loads greater than 1100 pF, a series resistor may be required on the output, as shown in Figure 15.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM94022
RS
OUT
LM94022
VDD
GND CLOAD > 1100 pF
OPTIONAL
BYPASS
CAPACITANCE
OUT
LM94022
VDD
GND
OPTIONAL
BYPASS
CAPACITANCE CLOAD < 1100 pF
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
Figure 14. LM94022 No Decoupling Required for Capacitive Loads Less than 1100 pF
Figure 15. LM94022 with Series Resistor for Capacitive Loading Greater than 1100 pF
CLOAD MINIMUM RS
1.1 nF to 99 nF 3 kΩ
100 nF to 999 nF 1.5 kΩ
1μF 800 Ω
OUTPUT VOLTAGE SHIFT
The LM94022 is very linear over temperature and supply voltage range. Due to the intrinsic behavior of an
NMOS/PMOS rail-to-rail buffer, a slight shift in the output can occur when the supply voltage is ramped over the
operating range of the device. The location of the shift is determined by the relative levels of VDD and VOUT. The
shift typically occurs when VDD- VOUT = 1.0V.
This slight shift (a few millivolts) takes place over a wide change (approximately 200 mV) in VDD or VOUT. Since
the shift takes place over a wide temperature change of 5°C to 20°C, VOUT is always monotonic. The accuracy
specifications in the ELECTRICAL CHARACTERISTICS table already include this possible shift.
SELECTABLE GAIN FOR OPTIMIZATION AND IN SITU TESTING
The Gain Select digital inputs can be tied to the rails or can be driven from digital outputs such as microcontroller
GPIO pins. In low-supply voltage applications, the ability to reduce the gain to -5.5 mV/°C allows the LM94022 to
operate over the full -50 °C to 150 °C range. When a larger supply voltage is present, the gain can be increased
as high as -13.6 mV/°C. The larger gain is optimal for reducing the effects of noise (for example, noise coupling
on the output line or quantization noise induced by an analog-to-digital converter which may be sampling the
LM94022 output).
Another application advantage of the digitally selectable gain is the ability to perform dynamic testing of the
LM94022 while it is running in a system. By toggling the logic levels of the gain select pins and monitoring the
resultant change in the output voltage level, the host system can verify the functionality of the LM94022.
14 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
+1.5V to +5.5V
GND
OUT
VDD
GS0
4
5 1
2
3
CBP
RIN
Input
Pin
CFILTER
LM94022
CSAMPLE
Reset
Sample
GS1
CIN
SAR Analog-to-Digital Converter
LM94022
VOUT
VDD
SHUTDOWN
Any logic
device output
R1
4.1V
R3
R2
0.1 PF
U3LM4040
R4
VOUT
V+
VT
VTemp
+
-U1
LM94022
VDD
U2
(High = overtemp alarm)
VT1
VT2
VTEMP
VOUT
VT1 = R1 + R2||R3
(4.1)R2
VT2 = R2 + R1||R3
(4.1)R2
LM94022
www.ti.com
SNIS140E –MAY 2006–REVISED JUNE 2013
APPLICATION CIRCUITS
Figure 16. Celsius Thermostat
Figure 17. Conserving Power Dissipation with Shutdown
Most CMOS ADCs found in microcontrollers and ASICs have a sampled data comparator input structure. When the
ADC charges the sampling cap, it requires instantaneous charge from the output of the analog source such as the
LM94022 temperature sensor and many op amps. This requirement is easily accommodated by the addition of a
capacitor (CFILTER). The size of CFILTER depends on the size of the sampling capacitor and the sampling frequency.
Since not all ADCs have identical input stages, the charge requirements will vary. This general ADC application is
shown as an example only.
Figure 18. Suggested Connection to a Sampling Analog-to-Digital Converter Input Stage
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM94022
LM94022
SNIS140E –MAY 2006–REVISED JUNE 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (February 2013) to Revision D Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 15
16 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM94022
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM94022BIMG NRND SC70 DCK 5 1000 TBD Call TI Call TI -50 to 150 22B
LM94022BIMG/NOPB ACTIVE SC70 DCK 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -50 to 150 22B
LM94022BIMGX/NOPB ACTIVE SC70 DCK 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -50 to 150 22B
LM94022QBIMG/NOPB ACTIVE SC70 DCK 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -50 to 150 22Q
LM94022QBIMGX/NOPB ACTIVE SC70 DCK 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -50 to 150 22Q
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM94022, LM94022-Q1 :
•Catalog: LM94022
•Automotive: LM94022-Q1
NOTE: Qualified Version Definitions:
•Catalog - TI's standard catalog product
•Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM94022BIMG SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3
LM94022BIMG/NOPB SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3
LM94022BIMGX/NOPB SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3
LM94022QBIMG/NOPB SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3
LM94022QBIMGX/NOPB SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM94022BIMG SC70 DCK 5 1000 210.0 185.0 35.0
LM94022BIMG/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM94022BIMGX/NOPB SC70 DCK 5 3000 210.0 185.0 35.0
LM94022QBIMG/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM94022QBIMGX/NOPB SC70 DCK 5 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated