To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
Is Now Part of
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2
May 2016
FODM3062, FODM3063, FODM3082, FODM3083
4-Pin Full Pitch Mini-Flat Package Zero-Cross
Triac Driver Output Optocouplers
Features
• Critical Rate of Rise of Off-Stage Voltage
- dv/dt of 600 V/µs Guaranteed
• Zero Voltage Crossing
• Peak Blocking Voltage
- 600 V (FODM306X)
- 800 V (FODM308X)
• Compact 4-Pin Surface Mount Package
- 2.4 mm Maximum Standoff Height
• Safety Regulatory Approvals:
- UL1577, 3,750 VACRMS for 1 Minute
- DIN-EN/IEC60747-5-5, 565 V Peak Working
Insulation Voltage
Applications
• Solenoid/valve controls
• Lighting controls
• Static power switches
• AC motor drives
• Temperature controls
• E.M. contactors
• AC motor starters
• Solid state relays
Description
The FODM306X and FODM308X series consist of an
infrared emitting diode optically coupled to a monolithic
silicon detector performing the function of a zero voltage
crossing bilateral triac driver, and is housed in a compact
4-pin mini-flat package. The lead pitch is 2.54 mm. They
are designed for use with a triac in the interface of logic
systems to equipment powered from 115/240 VAC lines,
such as solid state relays, industrial controls, motors,
solenoids and consumer appliances.
Functional Schematic Package Outlines
MAIN TERM.
1
2
ANODE
CATHODE 3
4MAIN TERM.
ZERO
CROSSING
CIRCUIT
)LJXUH)XQFWLRQDO6FKHPDWLF
)LJXUH3DFNDJH2XWOLQH
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 2
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Safety and Insulation Ratings
As per DIN EN/IEC 60747-5-5, this optocoupler is suitable for “safe electrical insulation” only within the safety limit
data. Compliance with the safety ratings shall be ensured by means of protective circuits.
Note:
1. Safety limit values – maximum values allowed in the event of a failure.
Parameter Characteristics
Installation Classifications per DIN VDE
0110/1.89 Table 1, For Rated Mains Voltage
< 150 VRMS I–IV
< 300 VRMS I–III
Climatic Classification 40/100/21
Pollution Degree (DIN VDE 0110/1.89) 2
Comparative Tracking Index 175
Symbol Parameter Value Unit
VPR
Input-to-Output Test Voltage, Method A, VIORM x 1.6 = VPR,
Type and Sample Test with tm = 10 s, Partial Discharge < 5 pC 904 Vpeak
Input-to-Output Test Voltage, Method B, VIORM x 1.875 = VPR,
100% Production Test with tm = 1 s, Partial Discharge < 5 pC 1060 Vpeak
VIORM Maximum Working Insulation Voltage 565 Vpeak
VIOTM Highest Allowable Over-Voltage 6000 Vpeak
External Creepage 5mm
External Clearance 5mm
DTI Distance Through Insulation (Insulation Thickness) 0.4 mm
TSCase Temperature(1) 150 °C
IS,INPUT Input Current(1) 200 mA
PS,OUTPUT Output Power(1) 300 mW
RIO Insulation Resistance at TS, VIO = 500 V(1) > 109
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 3
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be opera-
ble above the recommended operating conditions and stressing the parts to these levels is not recommended. In addi-
tion, extended exposure to stresses above the recommended operating conditions may affect device reliability. The
absolute maximum ratings are stress ratings only. TA = 25°C unless otherwise specified.
Symbol Parameter Value Unit
TSTG Storage Temperature -55 to +150 °C
TOPR Operating Temperature -40 to +100 °C
TJJunction Temperature -40 to +125 °C
TSOL Lead Solder Temperature 260 for 10 sec °C
EMITTER
IF (avg) Continuous Forward Current 60 mA
IF (pk) Peak Forward Current (1 μs pulse, 300 pps.) 1 A
VRReverse Input Voltage 6 V
PD(EMITTER) Power Dissipation (No derating required over operating temp. range) 100 mW
DETECTOR
IT(RMS) On-State RMS Current 70 mA
VDRM Off-State Output Terminal Voltage FODM3062/FODM3063 600 V
FODM3082/FODM3083 800 V
PD(DETECTOR) Power Dissipation (No derating required over operating temp. range) 300 mW
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 4
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Electrical Characteristics
TA = 25°C unless otherwise specified.
Individual Component Characteristic s
Transfer Characteristics
Zero Crossing Characteristics
Isolation Characteristics
Notes:
2. Test voltage must be applied within dv/dt rating.
3. This is static dv/dt. See Figure 10 for test circuit. Commutating dv/dt is function of the load-driving thyristor(s) only.
4. All devices are guaranteed to trigger at an IF value less than or equal to max IFT
. Therefore, recommended
operating IF lies between max IFT (10mA for FODM3062/82, 5mA for FODM3063/83) and absolute max IF (60 mA).
5. Steady state isolation voltage, VISO, is an internal device dielectric breakdown rating. For this test, pins 1 & 2 are
common, and pins 3 & 4 are common.
Symbol Parameter Test Conditions Device Min. Typ. Max. Unit
EMITTER
VFInput Forward Voltage IF = 30 mA All 1.50 V
IRReverse Leakage Current VR = 6 V All 100 μA
DETECTOR
IDRM
Peak Blocking Current Either
Direction Rated VDRM, IF = 0(2) All 500 nA
dv/dt Critical Rate of Rise of
Off-State Voltage IF = 0 (Figure 10)(3) All 600 V/μs
Symbol Parameter Test Conditions Device Min. Typ. Max. Unit
IFT LED Trigger Current Main Terminal
Voltage = 3 V(4)
FODM3062,
FODM3082 10
mA
FODM3063,
FODM3083 5
IH
Holding Current, Either Direc-
tion All 300 µA
VTM
Peak On-State Voltage,
Either Direction
IF = Rated IFT
,
ITM = 100 mA peak All 3 V
Symbol Parameter Test Conditions Device Min. Typ. Max. Unit
VIH
Inhibit Voltage,
MT1-MT2 Voltage
above which device
will not trigger
IFT = Rated IFT
All 20 V
IDRM2 Leakage in Inhibit State
IFT = Rated IFT
,
Rated VDRM,
Off-State
All 2 mA
Symbol Parameter Test Conditions Device Min. Typ. Max. Unit
VISO Steady State Isolation
Voltage(5)
1 Minute,
R.H. = 40% to 60% All 3,750 VACRMS
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 5
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Performance Characteristics
10
IF - FORWARD CURRENT (mA)
Fig. LED Forward Voltage vs. Forward Current
1 100
VF - FORWARD VOLTAGE (V)
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.8
1.7
TA
= -40°C
TA
= 25°C
TA
= 100°C
-40 -20 02040 60 80
TA - AMBIENT TEMPERATURE (°C)
Fig. Leakage Current vs. Ambient Temperature
100
IDRM - LEAKAGE CURRENT (nA)
0.1
1
10
100
1000
VDRM = 600V
02040 06
TA - AMBIENT TEMPERATURE (°C)
Fig. Holding Current vs. Ambient Temperature
-40 -20 100
IH
- HOLDING CURRENT (NORMALIZED)
0.1
1.0
10
80
NORMALIZED TO TA = 25°C
0204060
TA - AMBIENT TEMPERATURE (°C)
Fig. Trigger Current vs. Ambient Temperature
-40 -20 80
IFT - TRIGGER CURRENT (NORMALIZED)
0.8
0.6
0.8
1.0
1.2
1.4
1.6
VTM = 3V
NORMALIZED TO TA = 25°C
100
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 6
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Performance Characteristics (Continued)
-1012
VTM - ON-STATE VOLTAGE (V)
Fig. On-State Characteristics
-4 -3 -2 3 4
ITM - ON-STATE CURRENT (mA)
-200
-400
-600
-800
0
200
400
600
800
TA = 25°C
Fig. Off-State Output Terminal Voltage vs. Ambient Temperature
10
PWIN - LED TRIGGER PULSE WIDTH (°C)
Fig. LED Current Required to Trigger vs. LED Pulse Width
1001
IFT - LED TRIGGER CURRENT (NORMALIZED)
0
2
4
6
8
10
12
NORMALIZED TO
PWIN>
> 100μs
NORMALIZED TO T
A = 25°C
02040 06
TA - AMBIENT TEMPERATURE (°C)
VDRM
- OFF-STATE OUTPUT TERMINAL VOLTAGE
(NORMALIZED)
1.3
1.2
1.1
1.0
0.9
0.8
0.7
0.6
1.4
-40 -20
80 100
TA = 25°C
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 7
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Application Information
Figure . Static dv/dt Test Circuit
800V (FODM3082)Vdc
(FODM3083)
600V (FODM3062)
(FODM3063)
R = 10 kΩ
CTEST
X100
SCOPE
PROBE
PULSE
INPUT MERCURY
WETTED
RELAY
78V (FODM3062, FODM3063)
504V (FODM3082, FODM3083)
0 VOLTS
APPLIED VOLTAGE
WAVEFORM
dv/dt = 0.63 Vmax
RTEST
D.D.UU..TT..
τRC
Vmax == 800V (FODM3082, FODM3083)
=600V (FODM3062, FODM3063)
= 378
τRC (FODM3062, FODM3063)
= 504
τRC (FODM3082, FODM3083)
τRC
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
1. The mercury wetted relay provides a high speed repeated
pulse to the D.U.T.
2. 100x scope probes are used, to allow high speeds and
voltages.
3. The worst-case condition for static dv/dt is established by
triggering the D.U.T. with a normal LED input current, then
removing the current. The variable RTEST allows the dv/dt
to be gradually increased until the D.U.T. continues to trigger
in response to the applied voltage pulse, even after the LED
current has been removed. The dv/dt is then decreased until
the D.U.T. stops triggering. tRC is measured at this point
and recorded.
Figure . Inverse-Parallel SCR Driver Circuit (240VAC)
VCC
Rin
1
2
4
3
240 VAC
SCR
360 Ω
R1 D1
SCR
R2 D2
LOAD
Suggested method of firing two, back-to-back
SCR’s, with a Fairchild triac driver. Diodes can
be 1N4001; resistors, R1 and R2, are optional
330 ohms.
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
FODM3062
FODM3063
FODM3082
FODM3083
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 8
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Determining the Power Rating of the Series Resistors Used in a Zero-Cross Opto-
TRIAC Driver Application
Figure 1. Hot-Line Switching Application Circuit
0.01ȝ)
VCC
Rin 1
2
4
3240 VAC
HOT
NEUTRAL
360 Ω
*For highly inductive loads (power factor < 0.5), change this value to 360 ohms.
FODM3062
FODM3063
FODM3082
FODM3083 39
LOAD
Typical circuit for use when hot line switching of 240VAC
is required. In this circuit the “hot” side of the line is
switched and the load connected to the cold or neutral
side. The load may be connected to either the neutral or
hot line.
Rin is calculated so that IF is equal to the rated IFT of the
part, 5mA for the FODM3063/83 and 10mA for the
FODM3062/82. The 39Ω resistor and 0.01μF capacitor
are for snubbing of the triac and may or may not be
necessary depending upon the particular triac and load
used.
The following will present the calculations for
determining the power dissipation of the current
limiting resistors found in an opto-TRIAC driver
interface.
Figure 1 shows a typical circuit to drive a sensitive
gate four quadrant power TRIAC. This figure provides
typical resistor values for a zero line cross detecting
opto-TRIAC when operated from a mains voltage of
20V to 240V. The wattage rating for each resistor
isnot given because their dissipation is dependent
uponcharacteristics of the power TRIAC being driven.
Recall that the opto-TRIAC is used to trigger a four
quadrant power TRIAC. Please note that these opto-
TRIACs are not recommended for driving
“snubberless” three quadrant power TRIACs.
Under normal operation, the opto-TRIAC will fire when
the mains voltage is lower than the minimum inhibit
trigger voltage, and the LED is driven at a current
greater than the maximum LED trigger current. As an
example for the FODM3063, the LED trigger current
should be greater than 5mA, and the mains voltage is
less than 10V peak. The inhibit voltage has a typical
range of 10V minimum and 20V maximum. This
means that if a sufficient LED current is flowing when
the mains voltage is less than 10V, the device will fire.
If a trigger appears between 10V and 20V, the device
may fire. If the trigger occurs after the mains voltage
has reached 20Vpeak, the device will not fire.
The power dissipated from resistors placed in series
with the opto-TRIAC and the gate of the power TRIAC
is much smaller than one would expect. These current
handling components only conduct current when the
mains voltage is less than the maximum inhibit
voltage. If the opto-TRIAC is triggered when the mains
voltage is greater than the inhibit voltage, only the
TRIAC leakage current will flow. The power dissipation
in a 360Ω resistor shown in Figure 1 is the product
ofthe resistance (360Ω) times the square of the
currentsum of main TRIAC’s gate current plus the
currentflowing gate to the MT2 resistor connection
(330Ω).This power calculation is further modified by
the dutyfactor of the duration for this current flow.
The dutyfactor is the ratio of the turn-on time of the
main TRIACto the sine of the single cycle time.
Assuming a mainTRIAC turn-on time of 50μs
and a 60Hz mainsvoltage, the duty cycle is
approximately 0.6%.The opto-TRIAC only conducts
current while triggeringthe main TRIAC. Once the
main TRIAC fires, its on-state voltage is typically
lower than the on-statesustaining voltage of the
opto-TRIAC. Thus, once themain TRIAC fires, the
opto-TRIAC is often shunted off.This situation results
in very low power dissipation forboth the 360Ω and
330Ω resistors, when driving atraditional four
quadrant power TRIAC.
If a three quadrant “snubberless” TRIAC is driven by
the opto-TRIAC, the calculations are different. When
the main power TRIAC is driving a high power factor
(resistive) load, it shuts off during the fourth quadrant.
30 Ω
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 9
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
If sufficient holding current is still flowing through the
opto-TRIAC, the opto-TRIAC will turn-on and attempt
to carry the power TRIACs load. This situation typically
causes the opto-TRIAC to operate beyond its
maximum current rating, and product and resistor
failures typically result. For this reason, using an opto-
TRIAC to drive a three quadrant “snubberless” power
TRIAC is not recommended.
Power in the 360Ω resistor, when driving a sensitive
gate 4 quadrant power TRIAC:
IGT = 20mA
VGT = 1.5V
DF = 0.6%
P = (IGT +VGT / 330Ω)2 x 360Ω x DF
P = (20mA + 1.5 / 330Ω)2 *x 360Ω x 0.6% = 1.3mW
A 1/4 watt resistor is more than adequate for both the
360Ω and 330Ω resistors.
The real power in the snubber resistor is based upon
the integral of the power transient present when the
load commutes. A fast commuting transient may allow
a peak current of 4A to 8A in the snubbing filter.For
best results, the capacitor should be a non-polarized
AC unit with a low ESR. The 39Ω seriesresistor sets
a time constant and limits the peakcurrent. For a
resistive load with a power factor nearunity, the
commutating transients will be small. Thisresults in a
very small peak current given the 0.01μFcapacitor’s
reactance. Normally, for factional horse-power reactive
loads, the resistor found in the snubbercircuit will
have a power rating from 1/2W to 2W. Theresistor
should be a low inductance type to adequatelyfilter
the high frequency transients.
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 10
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Reflow Profile
Profile Freature Pb-Free Assembly Profile
Temperature Min. (Tsmin) 150°C
Temperature Max. (Tsmax) 200°C
Time (tS) from (Tsmin to Tsmax) 60–120 seconds
Ramp-up Rate (tL to tP) 3°C/second max.
Liquidous Temperature (TL) 217°C
Time (tL) Maintained Above (TL) 60–150 seconds
Peak Body Package Temperature 260°C +0°C / –5°C
Time (tP) within 5°C of 260°C 30 seconds
Ramp-down Rate (TP to TL) 6°C/second max.
Time 25°C to Peak Temperature 8 minutes max.
Time (seconds)
Temperature (°C)
Time 25°C to Peak
260
240
220
200
180
160
140
120
100
80
60
40
20
0
TL
ts
tL
tP
TP
Tsm a x
Tsm i n
120
Preheat Area
Max. Ramp-up Rate = 3°C/S
Max. Ramp-down Rate = 6°C/S
240 360
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 11
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Ordering Information
Note:
The product orderable part number system listed in this table also applies to the FODM3062, FODM3082 and
FODM3083 products.
Marking Information
Figure 13. Top Mark
Table 1. Top Mark Definitions
Part Number Package Packing Method
FODM3063 Full Pitch Mini-Flat 4-Pin Tube (100 units)
FODM3063R2 Full Pitch Mini-Flat 4-Pin Tape and Reel (2500 Units)
FODM3063V Full Pitch Mini-Flat 4-Pin, DIN EN/IEC60747-5-5 Option Tube (100 Units)
FODM3063R2V Full Pitch Mini-Flat 4-Pin, DIN EN/IEC60747-5-5 Option Tape and Reel (2500 Units)
1 Fairchild Logo
2 Device Number
3 DIN EN/IEC60747-5-5 Option (only appears on component ordered with this option)
4 One-Digit Year Code, e.g., “6”
5 Digit Work Week, Ranging from “01” to “53”
6 Assembly Package Code
1
2
6
4
35
3063
XV R
YY
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 12
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Tape Specifications
D
D
W
K
t
d
1
0PP
A
P
0
B0
0
2
E
F
W
1
0
Reel Diameter
Devices Per Reel
Max. Component Rotation or Tilt
Cover Tape Thickness
Cover Tape Width
Pocket Hole Dia.
Pocket Dimension
Pocket Location
Sprocket Hole Location
Sprocket Hole Dia.
Sprocket Hole Pitch
Tape Thickness
Pocket Pitch
Tape Width
Description Symbol Dimensions
2.54 Pitch
B
d
W1
D
K0
1
0
E
A
P
0
P
F
2
D
P
0
0
t
W
330 mm (13")
12.00±0.4
7.30±0.20
20° max
1.55±0.20
2.30±0.20
0.065±0.02
9.20
1.75±0.20
8.00±0.20
2.00±0.20
5.50±0.20
4.75±0.20
1.55±0.20
4.00±0.20
0.35±0.02
2500
©2006 Fairchild Semiconductor Corporation www.fairchildsemi.com
FODM30XX Rev. 1.2 13
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Footprint Drawing for PCB Layout
Note:
All dimensions are in mm.
0.80
6.50
2.54
1.00
www.onsemi.com
1
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
© Semiconductor Components Industries, LLC