ADA1200 Linear Amplifier ADVANCED PRODUCT INFORMATION - Rev 0.2 FEATURES * 50 to 1000 MHz Frequency Range * Input IP3: +24 dBm * Noise Figure: 2.3 dB * Single +5 V Supply * Small SOT-89 Package APPLICATIONS * Low Noise Amplifier for CATV Set-Top Boxes * CATV Drop Amplifier S24 Package SOT-89 PRODUCT DESCRIPTION The ADA1200 is a highly linear amplifier developed to meet the stringent requirements of CATV systems. Offered in a low cost SOT-89 package, this GaAs MESFET design offers low noise and low distortion over a wide range of frequencies. The device is ideally suited for applications as a Low Noise Amplifier in CATV Set-Top Boxes, and as a Drop Amplifier in CATV distribution systems. The ADA1200 requires a single +5 V supply, and typically consumes 400 mW of power. RF Input RF Output / Bias Figure 1: Block Diagram 05/2003 ADA1200 GND 4 1 2 3 RF IN GND RF OUT Figure 2: Pinout Table 1: Pin Description 2 PIN NAME 1 RFIN RF Input 2 GND Ground 3 RFOUT RF Output / Bias 4 GND Ground DESCRIPTION ADVANCED PRODUCT INFORMATION - Rev 0.2 05/2003 ADA1200 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Device Voltage (VCC) 0 +9 VD C RF Input Power (PIN) - +10 dB m -40 +150 C - TBD C Storage Temperature (TSTG) Junction Temperature Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER RF Input/Output Frequency Supply Voltage (VDD) Case Temperature (TC) MIN TYP MAX UNIT 50 - 1000 MHz - +5 - VD C -40 - +100 C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. ADVANCED PRODUCT INFORMATION - Rev 0.2 05/2003 3 ADA1200 Table 4: Electrical Specifications (TA = +25 C, VDD = +5 VDC, 75 system) PARAMETER Gain CTB (1) CSO (1) XMOD (1) MIN TYP MAX UNIT - 12 - dB - -75 - dB c - -63 - dB c - -73 - dB c 3rd Order Input Intercept Point (IIP3) (2) - +24 - dB m 2rd Order Input Intercept Point (IIP2) (3) - +46 - dB m Noise Figure - 2.3 - dB Input Return Loss - -25 - dB Output Return Loss - -25 - dB Thermal Resistance (JC) - - 50 C/W Supply Current - 80 - mA Notes: (1) 132 channels, +15 dBmV per channel (measured at input), 6 MHz channel spacing. (2) Two tones, -10 dBm per tone at input, 1 MHz spacing. (3) Two tones, at 425 MHz and 475 MHz, -10 dBm input per tone. VDD 0.01uF 100pF 10pF 5.1 Ohms 820nH ADA1200 6.8nH 3.3nH RF IN RF OUT 0.01uF 150pF Figure 3: Test Circuit 4 ADVANCED PRODUCT INFORMATION - Rev 0.2 05/2003 ADA1200 PERFORMANCE DATA Figure 4: Gain vs. Frequency (TA = +25 C, VDD = +5 V, 75 W System) 13.0 3.5 12.5 3.0 12.0 11.5 11.0 2.5 2.0 1.5 10.5 50 150 250 350 450 550 650 750 850 1.0 950 50 Frequency (MHz) 150 250 350 450 550 650 750 850 950 Frequency (MHz) Figure 6: Input Return Loss vs. Frequency (TA = +25 C, VDD = +5 V, 75 W System) 0 0 -10 Figure 7: Output Return Loss vs. Frequency (TA = +25 C, VDD = +5 V, 75 W System) -10 Output Return Loss (dB) Input Return Loss (dB) Figure 5: Noise Figure vs. Frequency (TA = +25 C, VDD = +5 V, 75 W System) 4.0 Noise Figure (dB) Gain (dB) 13.5 -20 -30 -40 -50 -20 -30 -40 -50 -60 50 150 250 350 450 550 650 750 850 950 -60 50 150 250 350 Frequency (MHz) 450 550 650 750 850 950 Frequency (MHz) S-parameter data for the unmatched device are available upon request, and on the ANADIGICS web site. ADVANCED PRODUCT INFORMATION - Rev 0.2 05/2003 5 ADA1200 28 -55 27 -60 26 -65 C T B (d B c ) IIP3 (dBm ) Figure 9: CTB vs. Frequency (TA = +25 C, VDD = +5 V, 132 channels, +15 dBmV input power per channel) Figure 8: Input IP3 vs. Frequency (TA = +25 C, VDD = +5 V, 75 W System) 25 -70 24 -75 23 -80 -85 22 50 150 250 350 450 550 650 750 850 0 950 100 200 300 500 600 700 800 900 Figure 11: CSO vs. Frequency (TA = +25 C, VDD = +5 V, 132 channels, +15 dBmV input power per channel) Figure 10: Input IP3 vs. Output Power (TA = +25 C, VDD = +5 V, 75 W system) 30 400 Frequency (MHz) Frequency (MHz) -55 -60 25 C S O (d B c ) IIP3 (dBm) -65 20 -75 50 MHz 200 MHz 600 MHz 900 MHz 15 -70 +0.75/-1.25MHzoffset -80 +1.25MHzoffset -85 10 0 2 4 6 8 10 0 12 100 200 300 700 800 900 -60 40 30 #1 20 10 XMOD (dBc) IIP 2 ( d B m ) 600 -55 50 -65 -70 -75 -80 0 0 2 4 6 8 10 12 -85 0 100 200 300 Output Power (dBm) 6 500 Figure 13: XMOD vs. Frequency (TA = +25 C, VDD = +5 V, 132 channels, +15 dBmV input power per channel) Figure 12: Input IP2 vs. Output Power (TA = +25 C, VDD = +5 V, 75 W system) 60 400 Frequency(MHz) Output Power (dBm) ADVANCED PRODUCT INFORMATION - Rev 0.2 05/2003 400 500 Frequency (MHz) 600 700 800 900 ADA1200 PACKAGE OUTLINE Figure 14: S24 Package Outline - SOT-89 1200 LLLLNN LLLL= FOUR NUMERIC CHARACTERS Figure 15: Branding Specification ADVANCED PRODUCT INFORMATION - Rev 0.2 05/2003 7 ADA1200 ORDERING INFORMATION PART NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING ADA1200S24Q1 -40 to +100C SOT-89 Package 1,000 piece Tape and Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 ADVANCED PRODUCT INFORMATION - Rev 0.2 05/2003