11433 Cover all Artwork 24/9/97 10:34 AM Page 1 S e m i c o n d u c t o r s f o r R a d i o / A u d i o Portable and home hi-fi/radio designer's guide June 1996 Philips Semiconductors CONTENTS Page Page INTRODUCTION 1 RADIO/AUDIO SYSTEMS Portable 1. Single chip AM pocket-sized radio 2. Mono FM card-sized radio 3. Portable mono AM/FM radio 4. Portable mono AM/FM radio/cassette recorder 5. Portable stereo AM/FM radio 6. Portable stereo FM radio 7. Portable self-tuned radio system (CPR120) Home 8. Electronically-tuned mini/midi AM/FM stereo receiver system 9. Music centre system (CCA210) 10. Astra digital radio 2 3 4 5 6 7 8 Multimedia radio tuners (OM5604/06/08) R(B)DS systems Radio PC cards DAB channel decoder NOTE Purchase of Philips I 2C components conveys a license under the Philips I 2C patent to use the components in the I 2C system, provided the system conforms to the I 2C specifications defined by Philips. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. Standard AM/FM radio receiver ICs Self-tuned AM/FM radio IC Audio amplifier ICs PLL frequency-synthesizer ICs Dolby noise-reduction ICs Microprocessor control and display Remote control circuits MPEG ICs Digital signal processing ICs Audio control ICs Discrete semiconductors for radio/audio CUSTOMER SUPPORT 9 10 12 Multimedia 11. 12. 13. 14. SEMICONDUCTORS FOR RADIO/AUDIO SYSTEMS 13 14 17 18 19 21 22 23 25 26 29 30 32 36 40 42 APPENDIX Alphanumeric index of ICs, modules and systems 44 INTRODUCTION The last few years have seen a revolution in the popularity of portable and home audio equipment. It's a revolution brought about by a greater choice of equipment for the consumer, ranging from pocket-sized radios and personal hi-fi to top quality music centres, at a price to suit all pockets. And it's almost entirely due to increased integration of electronic components and smaller packaging. This revolution is, of course, self-perpetuating: the enormous number of FM stereo stations that can now be received, and the availability of cassettes & CDs, has spurred on the production of even higher performance portable and domestic radio/audio with more features. For the semiconductor manufacturer, minimizing the number of peripheral circuit components is the norm, thus improving quality and reliability, and reducing the overall equipment size and cost. However integrating radio receivers presents its own special problems; overcrowded wavebands, small aerials and close proximity of components all increase the chances of interference. By fully exploiting the experience gained from our close relationship with radio setmakers, and combining it with our unrivalled experience of developing ICs using advanced circuit techniques, we've developed our present comprehensive range of completely-integrated radio systems that does more and performs better than ever before. Our range comprises ICs and discrete semiconductors for portable radios, mains-powered radios including Digital Satellite Broadcast (DSB) receivers, and radios for multimedia PCs. All are optimized for performance (distortion, sensitivity, etc.), minimum peripheral components and adjustments, and the best possible reception. For miniature `credit-card' or pocket-sized radios, we have an AM mono receiver IC that operates from a 3 V battery with minimum power consumption and requires very few peripheral components. This IC overcomes the difficulty of providing manual tuning for such a small radio by incorporating a simple search tuning facility operated by two push-buttons. For personal radios, clock radios, portable radios and portable radio-recorders, we offer a variety of highly-integrated two-chip manually-tuned AM/FM configurations; for mono and stereo reception. We also have an AM/FM stereo configuration that is optimized for use with a computercontrolled PLL frequency synthesizer for digital tuning. All these ICs operate from as little as 2 V or up to 18 V with minimum power consumption and require very few, if any, peripheral components. This minimizes costs and simplifies design. The latest addition to our range of radio ICs is an innovative computer-controlled AM/FM Self-Tuned Radio (STR) which 1) Dolby is a registered trademark of the Dolby Labs Licensing Corporation, San Francisco, CA, USA. 1 operates from a 2.2 V to 12 V supply. This single-chip self-tuned radio performs all the functions from the aerial input to the stereo decoder outputs. The tuning concept used in the STR combines the advantages of manual tuning with electronic tuning facilities and features. The inherent fuzzy logic behaviour of the STR mimics manual tuning (coarse tuning followed by fine tuning) and achieves fast and reliable tuning to the desired frequency. The performance, flexibility and wide supply voltage range of our ICs for personal radios and portables also allows them to be combined with other ICs from our radio/audio range to form chipsets for all performance classes of mains-powered stereo FM, MW and LW hi-fi tuners mini/midi systems and music centres. ICs that can be added include a PLL frequency synthesizer plus microcontroller for electronic tuning and control, source selector, tone/volume/balance control circuits, power amplifiers, CD player ICs, Dolby1) B/C noise reduction circuits for cassette recorders, and remote control ICs. And with the advent of multimedia systems we offer a range of radio PC cards based around the OM56xx family of tuners. These radio PC cards offer full R(B)DS capabilities and are fully shielded against the extreme electrical noise found within a PC to deliver clear, hi-fi quality FM stereo radio signals in a multimedia system. 1. SINGLE CHIP AM POCKET-SIZED RADIO (TEA5551T) The TEA5551T is a complete AM radio IC incorporating a dual AF amplifier with low quiescent current. It is primarily designed for pocket radios operating from a 3 V supply (maximum output power is with a 4.5 V supply, with a power output of 2 x 60 mW when used with 32 headphones or 100 mW in bridge-tied load (BTL) with a 50 loudspeaker). This IC has an AF part with low radiation (HF noise) and good overdrive performance. AM RECEIVER TEA5551T MSC126 Fig.1 Single-chip card-size AM radio Table 1 Typical radio data Characteristic Value supply voltage (VS) supply current frequency range up to 30 MHz IF Features very high sensitivity good IF suppression built-in dual AF amplifier with soft clipping and limited bandwidth AM mute switch low current consumption AF inputs are accessible for source selection, e.g. as in AM/ FM radio (with TDA7021T). 3V 5 mA 468 kHz temperature range -25 to +60 C Table 2 TEA5551T data (specified for 3 V supply) Characteristic Value supply voltage (VS) 1.8 to 4.5 V AM characteristics (modulation depth, m = 0.3) sensitivity for 10 mV AF output for (S+N)/N = 26 dB for (S+N)/N = 50 dB 1.5 V 15 V 10 mV signal handling (m = 0.8, THD = 10%) 80 mV THD 0.8 % AF characteristics output power per channel (THD = 10%, RL = 32 ) 25 mW voltage gain 32 dB channel separation package 50 dB SO16 (SOT109A) 2 2. MONO FM CARD-SIZED RADIO (TDA7088T + TDA7050T) The TDA7088T is the latest of our single-chip FM receivers for pocket radios. Previous single-chip receivers have used trim-capacitor tuning systems which meant using a very small tuning knob to cover the whole FM band. The TDA7088T overcomes this by incorporating a simple search tuning facility which can be operated by two push buttons. The TDA7088T contains all stages needed for FM reception. Operation is based on a Frequency-Locked Loop (FLL) system with conversion to an IF of 75 kHz. We recommend using this receiver in conjunction with the TDA7050T (or the TDA7052) audio amplifier. AM RECEIVER MONO AMPLIFIER TDA7088T TDA7050T (or TDA7052) MSC111 Fig.2 Two-chip card-size mono FM radio Table 3 Typical overall radio data Characteristic Value supply voltage (VS) supply current frequency range 0.5 to 110 MHz IF 75 kHz temperature range TDA7050T features no external components operates from a 1.6 to 6 V supply fixed gain of 32 dB (BTL). -10 to +70 C Table 4 TDA7088T data (specified for 3 V supply) Characteristic Value supply voltage (VS) TDA7088T features contains all stages of a mono FM receiver from antenna to audio output mute circuit search tuning with a single varicap diode mechanical tuning also possible with integrating AFC AM application is supported power supply polarity protection power supply voltage down to 1.8 V. 3V 8.4 mA 1.8 to 5 V supply current 5.2 mA AF output voltage (VO; RL = 22 k) 85 mV THD 1% sensitivity (EMF for -3 dB limiting) mute off mute on 3 V 6 V signal handling (f = 75 kHz, THD < 10%) S/N 200 mV 56 dB package SO16 (SOT109A) Note: frf = 96 MHz, f = 22.5 kHz and fmod = 1 kHz unless stated otherwise Table 5 TDA7050T data (specified for 3 V supply) Characteristic Value supply voltage (VS) 1.6 to 6 V quiescent current 3.2 mA BTL output power (PO; RL = 32 , THD = 10 %) 140 mW noise voltage at output 140 V The TDA7052 amplifier produces 39 dB gain with a 3 V supply. See page 22 Audio amplifier ICs for more amplifier details. 3 3. PORTABLE MONO AM/FM RADIO (TEA5710(T) + TDA7052/52A/52B) The TEA5710(T) is an AM/FM receiver IC for use in clock radios, portable radios, mains-fed radios and medium-fi sets. It incorporates all circuitry from the AM/FM frontend to the detector outputs. Only a minimum number of external components are required to complete a radio set. We recommend using it with the TDA7052 or TDA7052A/52B amplifier. The TEA5710(T) has many features such as distributed selectivity on both AM and FM, and a symmetrical AFC for tuning. The distributed IF gain allows a simple PCB layout. A new aspect in AM reception is the high impedance AM RF input made by a differential MOST pair. This enables connection to the top of the input selectivity (e.g. the ferroceptor) which simplifies radio design and reduces the number of necessary contacts. AM/FM RECEIVER MONO AMPLIFIER TEA5710(T) TDA7052 or TDA7052A/52B RL = 8 MSC112 Fig.3 Portable mono AM/FM radio Table 6 Typical overall radio data (specified for 3 to 6 V supply) Characteristic Value supply voltage (VS) supply current 3 to 12 V 11.5 to 16 mA frequency range AM FM up to 30 MHz 87.5 to 108 MHz temperature range -15 to +60 C Table 7 TEA5710(T) data (specified for 3 V supply) Characteristic Value supply voltage (VS) 2.0 to 12 V AM performance supply current 7.5 mA AF output voltage (VO) 45 mV THD 0.8 % sensitivity (EMF for -3 dB limiting) 1.6 mV/m FM performance TEA5710(T) Features wide supply voltage range low current consumption high selectivity with distributed IF gain LED driver for tuning indication high input sensitivity good strong-signal behaviour low output distortion designed for simple and reliable PCB layout high impedance MOSFET input on AM. Amplifiers The A and B versions differ from the TDA7052 in that they have a DC volume control with mute mode. See page 22 Audio amplifier ICs for more amplifier details. supply current 9.0 mA AF output voltage (VO) 65 mV THD 0.3 % sensitivity (EMF for -3 dB limiting) 1.2 V Note: AM: frf = 1 MHz, m = 30 % and fmod = 1 kHz FM: frf = 100 MHz, f = 22.5 kHz and fmod = 1 kHz Table 8 TDA7052 data (specified for 6 V supply) Characteristic Value supply voltage (VS) 3 to 18 V quiescent current 4 mA output power (PO; RL = 8 , THD = 10 %) 1.2 W THD 0.2 % Table 9 TDA7052A/53B data (specified for 6 V supply) Characteristic Value supply voltage (VS) 4.5 to 18 V quiescent current 7 mA output power (PO; RL = 8 , THD = 10 %) 1.1 W THD 0.3 % 4 4. PORTABLE MONO AM/FM RADIO/CASSETTE RECORDER (TEA5710(T) + TDA1016) With the same receiver as the previous radio, this design features the TDA1016 recorder/ playback amplifier IC. This couples all the qualities of the TEA5710(T) with those of the TDA1016 for a high-performance portable radio-recorder. The TDA1016 incorporates an audio power amplifier, preamplifier and ALC circuit. Its wide supply voltage range makes it suitable for both portable and mains applications. AM/FM RECEIVER MONO AMPLIFIER TEA5710(T) TDA1016 MSC113 Fig.4 Portable mono AM/FM radio/cassette recorder Table 10 Typical overall radio-recorder data (specified for 6 V supply) Characteristic Value recommended supply voltage (VS) supply current 6 to 12 V 19 mA frequency range AM FM up to 30 MHz 87.5 to 108 MHz temperature range TDA1016 features separate record/playback preamplifier and power amplifier incorporates ALC (automatic level control) for recording voltage stabilization (2.6 V) short-circuit protection thermal protection standby switching facility to minimize current drain. RL = 4 -15 to +60 C Table 11 TEA5710(T) data (specified for 3 V supply) Characteristic Value supply voltage (VS) 2.0 to 12 V AM performance supply current 7.5 mA AF output voltage (VO) 45 mV THD 0.8 % sensitivity (EMF for -3 dB limiting) 1.6 mV/m FM performance supply current 9.0 mA AF output voltage (VO) 65 mV THD 0.3 % sensitivity (EMF for -3 dB limiting) 1.2 V Note: AM: frf = 1 MHz, m = 30 % and fmod = 1 kHz FM: frf = 100 MHz, f = 22.5 kHz and fmod = 1 kHz Table 12 TDA1016 data (specified for 6 V supply) Characteristic Value supply voltage (VS) quiescent current 3.6 to 15 V 10 mA output power: Vs = 6 V; RL = 4 , THD = 10 % Vs = 9 V; RL = 4 , THD = 10 % 5 1W 2W 5. PORTABLE STEREO AM/FM RADIO (TEA5711(T)/ 12(T) + TDA7053(A)A/57(A)Q) For a portable stereo radio, we offer a variety of two-chip solutions, depending on your performance requirements. The TDA7057Q/57AQ amplifiers offer outputs as high as 3 W per channel while the TDA7053/53A offer 1.2 W per channel. All ICs can operate from a 3 to 12 V supply and require no peripheral components. Both the TEA5711 and TEA5712 receiver ICs differ from the TEA5710 in that they include a stereo decoder. Principally, their applications include portable radios, Mini/Midi receiver sets and personal headphone radios. The TEA5712 also facilitates digital tuning. Details of all three receivers are given in section 7. TEA5711(T)/12(T) features wide supply voltage range low current consumption high selectivity with distributed IF gain high input sensitivity good strong-signal behaviour (10 V/m AM, 500 mV FM) low output distortion simple, reliable PCB layout high impedance AM input LED driver for stereo indication soft mute signal-dependent stereo signal-level output (TEA5711) stop-signal output (TEA5712) IF output signals available for IF counting (TEA5712). Amplifiers features fixed closed-loop voltage gain (39 dB for TDA7053(A), 40 dB for TDA7057(A)Q) DC volume control with mute mode (TDA7053A/57AQ only). STEREO AM/FM RECEIVER STEREO AMPLIFIER L TEA5711(T) or TEA5712(T) TDA7053/53A or TDA7057Q/57AQ R RL = 8 (2x), for TDA7053/53A RL = 16 (2x), for TDA7057Q/57AQ MSC114 Fig.5 Portable stereo AM/FM radio Table 13 Typical overall radio data (specified for 6 V supply) Characteristic Value supply voltage (VS) 18 mA frequency range AM FM up to 30 MHz 87.5 to 108 MHz temperature range -15 to +60 C Table 14 TEA5711(T) and TEA5712(T) data (specified for 3 V supply) Characteristic Value supply voltage (VS) 2.0 to 12 V channel separation 30 dB AM performance supply current 14 mA AF output voltage (VO) 45 mV THD 0.8 % sensitivity (EMF for -3 dB limiting) 1.6 mV/m FM performance supply current 16 mA AF output voltage (VO) 65 mV THD 0.3 % sensitivity (EMF for -3 dB limiting) 1.2 V Note: AM: frf = 1 MHz, m = 30 % and fmod = 1 kHz FM: frf = 100 MHz, f = 22.5 kHz and fmod = 1 kHz Table 15 TDA7053/53A data (specified for 6 V supply) Characteristic Value supply voltage (VS) 3 to 18 V quiescent current 9 mA output power/channel (PO; RL = 2 x 8 , 10% THD) 1.2 W THD 0.2 % Table 16 TDA7057Q/57AQ data (specified for 11 V supply) Characteristic Value supply voltage (VS) quiescent current See page 22 Audio amplifier ICs for more amplifier details. 3 to 12 V supply current 3 to 18 V 10 mA output power/channel (PO; RL = 2 x 16 , 10% THD) THD 3W 0.25 % 6 6. PORTABLE STEREO FM RADIO (TDA7021T + TDA7040T + TDA7050T) The TDA7021T stereo FM receiver circuit is for pocket-sized radios and is fully compatible with applications using the low-voltage micro tuning system (MTS). The IC has a frequency locked loop (FLL) system with intermediate frequency of 76 kHz. The selectivity is obtained by active RC filters. Because of the low-pass characteristics of the FLL, a 50 kHz roll-off compensation is performed by the integral LF amplifier. For mono applications, this amplifier can be used to drive an earphone. The field-strength detector enables field-strength dependent channel separation control. We recommend using this receiver in conjunction with the TDA7040T PLL stereo decoder and the TDA7050T stereo audio amplifier. FM RECEIVER TDA7021T STEREO DECODER STEREO AMPLIFIER TDA7040T TDA7050T MSC115 Fig.6 Three-chip card-size stereo FM radio Table 17 Typical overall radio data Characteristic Value supply voltage (VS) supply current 9.5 mA frequency range 1.5 to 110 MHz temperature range -10 to +70 C Table 18 TDA7021T data (specified for 3 V supply) Characteristic Value supply voltage (VS) TDA7040T features built-in four pole low-pass filter with 70 kHz corner frequency integrated 228 kHz oscillator pilot presence detector and soft mono/stereo blend built-in interference suppression adjustable gain. 1.8 to 6 V supply current 6.3 mA AF output voltage (VO; RL = 100 k) 90 mV THD (f = 22.5 kHz) 0.7% sensitivity muting disabled muting 4.0 V 5.0 V signal handling (f = 75 kHz, THD < 10%) 200 mV S/N TDA7021T features RF input stage mixer local oscillator IF amplifier/limiter frequency detector mute circuit loop amplifier internal reference circuit LF amplifier for mono earphone amplifier or MUX filter field-strength dependent channel separation control facility. 3V 60 dB Note: frf = 96 MHz, f = 22.5 kHz and fmod = 1 kHz unless stated otherwise Table 19 TDA7050T data (specified for 3 V supply) Characteristic Value supply voltage (VS) 1.6 to 6 V quiescent current 3.2 mA noise voltage at output 140 V Table 20 TDA7040T data (specified for 3 V supply) Characteristic Value supply voltage (VS) supply current 1.8 to 6 V 3.0 mA total harmonic distortion 0.3% signal to noise ratio 70 dB TDA7050T features no external components operates from a 1.6 to 6 V supply very low quiescent current (typ. 3.2 mA with 3 V supply). 7 7. PORTABLE SELF-TUNED RADIO SYSTEM (CPR120) The CPR120 computer-controlled personal radio system comprises an FM, MW, LW and SW stereo self-tuned radio. The system contains functions such as search tuning, preset control, LCD display and an interface for a cassette player (optional). The ICs at the heart of the music centre system are: P83CLX34 CPR120S masked programmed microcontroller. See page 26 Microprocessor control and display for more information. TEA5757H AM receiver (LW, MW and SW) FM stereo receiver tuning synthesizer and radio on one chip microcontroller bus interface auto-search and preset-mode high input sensitivity low output distortion tuning is independent of channel spacing low power consumption due to standby mode. See page 21 Self-tuned AM/FM radio IC for more details on the TEA5757H. TDA7050(T) 150 mW BTL or 2 x 75 mW headphone amplifier operates with battery supplies from 6 V down to 1.6 V very low quiescent current (typically 3.2 mA with 3 V supply). TDA1308T 60 mW stereo headphone amplifier 110 dB signal-to-noise ratio low current drain (typically 3 mA with 5 V supply). TUNER F/E L IF AMP/DET. MPX R TEA5757H SYNTH. L HEADPHONE AMPLIFIER TDA8542(T), TDA7050(T) or TDA1308T R volume CPR120 MICROCONTROLLER P83CLX34 LCD DISPLAY MSB622 Fig.7 CPR120 electronically tuned personal radio TDA8542(T) 2 x 1 W headphone amplifier Standby mode controlled by CMOS compatible levels Gain can be fixed with external resistors. CPR120 features Tuning - FM, MW, LW and SW bands - Search up/down tuning with wrap round. Actual search is done by the TEA5757 IC and the frequency found is read by the microcontroller - Manual up/down tuning - Frequency scan-up function, searching for the next station in the band and pausing 6 s before the next station is searched - 5 presets for FM, MW, LW and SW - AST (Automatic Store Tuning) searches for and stores the strongest (FM and MW) transmitters - Saving last band and frequency of the station at power off (in standby mode) - Preset up/down or preset 1 to preset 5 select keys - 16 geographical area options (programmable). 8 Clock functions - 24 hr clock display function, also in standby mode - Switch on timer function - Sleep timer function. Sound control - Mute output to mute headphone or power amplifier. Standard or extended LCD Icons: SLEEP, TIMER, STEREO, TUNED, FM, MW, LW, SW, MHz, kHz, AST, P1 to P5 (preset number), 5 (5 kHz in SW band), MEMORY. Cassette deck - Tape play detection by means of the mute pin. Local control - 9 local keys. Switching on/off - Momentary on/off switch - Continuous mains power supply allows the RAM to save preset data and clock functions - Recall of last band, preset and frequency when switching on from standby - Output allows power supply to be controlled by the timer functions - Input detects static power-on switch. 8. ELECTRONICALLY-TUNED MINI/MIDI AM/FM STEREO RECEIVER SYSTEM This mains-fed, mid-fi radio design offers a wide degree of flexibility in terms of features and power output. The design is based on the TEA5712(T) AM/FM stereo receiver, which includes a stereo decoder. Remote-controlled digital tuning is managed by a microcontroller (P83Cxxx family) operating a PLL frequency synthesizer (TSA6060(T)) via the I2C-bus. The TDA1524A audio controller facilitates bass, treble and volume control for each channel. A variety of amplifiers are available for a wide range of power outputs. TEA5712(T) features wide supply voltage range low current consumption high selectivity with distributed IF gain high input sensitivity good strong-signal behaviour (10 V/m AM, 500 mV FM) low output distortion simple, reliable PCB layout high impedance AM input LED driver for stereo indication soft mute signal-dependent stereo stop-signal output IF output signals available for IF counting. AM/FM RECEIVER WITH STEREO DECODER AUDIO CONTROL TDA1524A TEA5712(T) PLL FREQUENCY SYNTHESIZER MICROCONTROLLER TSA6060(T) P83Cxxx L AUDIO AMPLIFIER TDA2615, TDA2616 (2x), TDA1514A (2x) or TDA1521 R REMOTE CONTROL MSC116 Fig.8 Electronically-tuned Mini/Midi AM/FM stereo receiver Table 21 Typical overall radio data Characteristic Value frequency range AM FM up to 30 MHz 87.5 to 108 MHz temperature range TSA6060(T) features on-chip, high input-sensitivity AM & FM prescalers on-chip, high-performance 1 input (2 output) tuning voltage amp. for AM & FM loop filters on-chip, multi-level current amp to adjust loop gain high-speed tuning due to a powerful digital memory phase detector oscillator frequency ranges of 512 kHz to 30 MHz, 30 to 200 MHz 1 reference oscillator for both AM & FM selectable reference frequencies for both tuning ranges serial 2-wire I2C-bus. in-lock detector output pin TDA1524A features few external components required low noise bass emphasis can be increased by a double-pole lowpass filter wide power supply voltage range mute switch via external pin loudness function. 9 -15 to +60 C Amplifier features (RL = 8) TDA2615 - 2 x 6 W TDA2616 (x2) - 2 x 20 W TDA1514A (x2) - 2 x 40 W TDA1521 - 2 x 12 W. Full details of all these ICs are given in the appropriate sections of this guide. 9. MUSIC CENTRE SYSTEM (CCA210) The CCA210 computer-controlled music centre system comprises an FM, MW, LW and SW stereo radio (for battery and mains-fed portables, and mini/midi audio systems), combined with a cassette player deck and a CD player. The entire system is controlled by a CMOS microcontroller. The ICs at the heart of the music centre system are: TEA5757H An AM/FM STR (self-tuned radio) receiver including synthesizer and stereo decoder. TDA2615/16(Q) 2 x 10/20 W (maximum output power) hi-fi audio amplifier with mute. PCF8577CT I2C-bus controlled LCD driver providing 32 segment drive lines and 2 backplane select lines (64 segments total). SAA3010T RC-5 remote control transmitter (optional). Main features of the CCA210: Tuning - Four bands FM, MW, LW and SW - FLL tuning principle - Search up/down tuning with wrap round. Actual search is done by the TEA5757 IC and the frequency found is read by the microcontroller - Manual up/down tuning - 10 presets for FM; 5 presets for MW, LW and SW - Preset scan pausing for 10 s on every station before selecting the next preset in that band - AST (Automatic Store Tuning) searches for and stores the strongest (FM, MW LW and SW) transmitters - Saving last band and frequency of the station at power off (in standby mode) - 16 geographical area options (programmable). Sound control - Volume up/down control by means of a motor-controlled potentiometer - Volume, balance, bass and treble control by means of an I2C-bus controlled audio processor or by potentiometers - Audio select key to select the audio function bass, treble and balance controls by means of the audio up/down keys - Selectable inputs: radio, CD, tape and auxiliary - Mute output to mute the power amplifiers (via pin or audio processor) - Saving last sound settings at power off (standby mode). Control - 36 local keys and/or RC-5 remote. Clock functions - 12/24 hr clock display function, also in standby mode - Switch on/off timer functions - Sleep timer function. aux TUNER TEA5757H radio CD tape INPUT SELECTOR HEF4052 AUDIO CONTROL TDA8424 OR MOTOR VOLUME CONTROL POWER AMPLIFIER TDA2615/16 mute audio control via pins or I 2 C-bus tuner interface CD PLAYER CDM12.1 SAA7376GP TDA1300T TDA7073A (2x) TDA1311AT MICRO CONTROLLER CCA210S OM5234/FBP EEPROM PCF8582C (optional) I 2 C-bus RC-5 RECEIVER TAPE DECK CD record & tape play LCD DRIVER PCF8577CT STAND-BY POWER SUPPLY RC-5 TRANSMITTER SAA3010T (optional) LCD MSC117 Fig.9 CCA210 music centre using a self-tuned radio 10 Display Icons: CD INTRO, CD REPEAT, CD RANDOM, SLEEP, TIMER ON/OFF, CD MEMORY, CD TRACK, FM, MW, LW, SW, MHz, kHz, CH, AM/PM CLOCK, STEREO Other: two 7-segment digits for CD TRACK or PRESET, and four 7-segment digits for frequency and time. Cassette deck - Key to select tape mode - Automatic detection of play mode when the play key is pressed - Interfaces with a mechanicallycontrolled deck - CD synchro record mode. In CD mode the CD starts playing when the record key is pressed. CD player - 3-beam CDM 12.1 mechanism and motorized tray loader - full CD control including: random and scan play, track programming features, track/ search up/down control, A-B repeat, track and disc repeat, direct track selection, various display formats, and a service mode - CD system to be used with a tray loader (L1210) or a top loader Auxiliary input - Key to select auxiliary mode. Switching on/off - Momentary on/off switch - Continuous mains power supply allows (RAM to save the preset data when no EEPROM is used) clock functions - Recall of last mode (radio/CD/ tape/aux.). In radio mode, last band, preset and frequency, analog sound settings when switching on from standby 11 - Output to allow the power supply to be controlled by the timer functions. Non-volatile memory A 256 byte non-volatile memory can be installed to store the following information: - 10 presets for each band - Last selected band, preset number and frequency - Audio settings (volume, balance, bass, treble) and selected source - Status and settings of the switch on/off timers. 10. ASTRA DIGITAL RADIO Our Astra digital radio (ADR) design is based on the SAA2530 ADR/DMX digital receiver, and the SAA2502 ISO/MPEG audio source decoder. SAA2530 features full ADR frequency range gain control amplifier buffered clock output of 12.288 MHz and 8.192 MHz or 4.096 Mhz 8-bit ADC QPSK demodulation depuncturing decimation and matched filters soft decision thresholds for Viterbi decoding differential decoding descrambling DMX (digital music express) decryption MPEG layer 2 synchronization and output additional programmable clock output FEC for ancillary data L3- and I2C-bus interface QFP44 package. SAA2502 features DAC output (256 or more times oversampled internal dynamic range compression algorithm CRC protection of scale factors (ADR/DAB) ADR DEMODULATION, DECODING & AUDIO PROCESSING L SATELLITE TUNER MPEG SAA2530 R SAA2502 I2S-bus SPDIF LNB POWER ancillary data REMOTE CONTROL TRANSCEIVER MICROCONTROLLER PUSH BUTTONS AND DISPLAYS CARD READER AND ELECTRONICS MSC027 Fig.10 ADR receiver block diagram low sampling frequency decoding possibilities (24 kHz, 22.05 kHz and 16 kHz) SPDIF and I2S output bit-rate and sampling frequency may be overruled by the microcontroller while the SAA2502 is trying to establish frame synchronization L3- and I2C-bus interface QFP44 package. Full details of other peripheral ICs in the ADR receiver are given in the appropriate sections of this guide. 12 11. MULTIMEDIA RADIO TUNERS (OM5604/06/08) The OM5604, OM5606 and OM5608 FM tuner modules are designed to operate in the harsh electrical environment of the PC and deliver clear, hi-fi quality stereo radio signals in a multimedia system. The modules are fully shield for the PC environment and offer MPX output for Radio (Broadcast) Data Systems (R(B)DS) decoding. Both modules have an 75 RF aerial input (the OM5604 has an F-connector and the OM5606 and an IEC-connector). The OM5604/06 modules comprise three ICs: the TEA5757H, the PCF8574T and the TDA1308T. The TEA5757H self-tuned radio (STR) FM receiver lies at the heart of the modules. It is an FM receiver, stereo decoder and tuning synthesizer on one chip. After searching for the desired channel, it automatically locks onto the signal for the best possible reception. If the receiver is tuned to a strong local transmission, local/DX switching ensures reception is not overpowered. More details on the TEA5757H STR are given in the section Selftuned AM/FM radio IC. The PCF8574T is a bus converter that provides I2C-bus control and has three I/O lines for additional control functions. The TDA1308T is a line amplifier with two line outputs. FM RECEIVER FE 75 aerial IF AMP/DET MPX R line LINE AMPLIFIER TDA1308T TEA5757H output L SYNTH. MPX OM5604 BUS CONVERTOR PCF8574T (optional) 3 I/Os MSB942 IIC-bus or STR-pins Fig.11 PC-radio base module Table 22 OM5604 and OM5606 data Characteristic Value supply voltage (VS) audio output 4.5 to 5.5 V 900 mV RMS RF input connector frequency range 75 87.5 to 108 MHz FM stereo signal-to-noise ratio 63 dB channel separation 28 dB channel imbalance 0.5 dB stereo blend function 10 dB total harmonic distortion FM mono signal-to-noise ratio 3% 71 dB 3 dB limiting sensitivity 3.5 dB RF sensitivity 2.2 dB AM suppression 58 dB total harmonic distortion 1.5% Features local/DX switching MPX output for R(B)DS decoding I2C-bus controlled with three I/O ports for additional control functions 13 small package size (34 x 86 x 14 mm) electronic fast tuning system meets FCC requirements on radiation. 12. R(B)DS SYSTEMS TP QUAL TA M/S SYNC I2C-bus RDS system This demodulator & decoder system is based around two ICs: the SAA6579T RDS demodulator and the CCR910, CCR911, CCR912 or CCR921 RDS decoder. These ICs recover the bi-phase inaudible frequency/programme information which is serially transmitted with FM radio broadcasts that use the Radio Data System (RDS). The information is converted into data for controlling the tuning/ display functions of the radio via the I2C-bus and the main microcontroller of the radio. In the RDS demodulator, the RDS signal is separated from the MPX signal by a 57 kHz bandpass filter, and digitized using a comparator. The digitized signal is then synchronously demodulated to recover the bi-phase data symbols. For this function, the suppressed 57 kHz subcarrier is regenerated by a special PLL system (Costas loop). The demodulated data symbols are further processed in an integrate and dump circuit followed by a differential decoder which generates the RDS data (RDDA) signal. The bit rate RDS clock (RDCL) is recovered by a second PLL. The integrate and dump circuit also generates a quality signal (QUAL) for every data bit. The RDS decoder is an 80C51 family microcontroller with intelligent RDS data decoding and/ or pre-processing software. The software incorporates automatic error detection/correction. A subset of the decoded RDS data is present within the serial interface protocol and also made available on the pins of the decoder IC. RDS DEMODULATOR RDDA 57 kHz FILTER MPX DIGITIZER R(B)DS DECODER CCR9xx RDS DEMOD. RDCL SAA6579T to/from radio microcontroller MSC118 Fig.12 RDS demodulator and decoder system Table 23 SAA6579T data Characteristic Value supply voltage (VS) 5V supply current 6 mA oscillator frequency 4.332/8.664 MHz min. RDS input amplitude (RMS) 1 mV temperature range -40 to +85 C package DIL16, SO16 +5 V OSCI MPX signal MUX ANTIALIASING FILTER 57 kHz BANDPASS (8th ORDER) RECONSTRUCTION FILTER V DDD OSCO OSCILLATOR AND DIVIDER QUALITY BIT GENERATOR QUAL DIFFERENTIAL DECODER RDDA SCOUT SAA6579T CIN +5 V CLOCKED COMPARATOR VDDA V ref COSTAS LOOP VARIABLE AND FIXED DIVIDER BIPHASE SYMBOL DECODER VP1 REFERENCE VOLTAGE RDCL CLOCK REGENERATION AND SYNC VSSA TEST LOGIC AND OUTPUT SELECTOR SWITCH TSTLD TEST T57 VSSD MGA510 Fig.13 RDS demodulator (SAA6579T) RDS/RBDS system This is similar to the RDS system described above, except a CCR921 R(B)DS decoder is used. The CCR921 supports all types of R(B)DS groups and is easy to use via the I2C-bus interface. Furthermore, as the timing requirements of the (main-) set controller of the R(B)DS data 14 processing are reduced, radio control software can be developed specifically for radio features. SAA6579T features on-chip preamplifier on-chip 57 kHz bandpass filter on-chip comparator quality signal output CMOS-level digital outputs. CCR910/911/912 features synchronization on binary RDS data stream from demodulator synchronization available via pin error detection & correction: - checks for transmission error - corrects errors when enabled - pin-programmable correction (no correction; max. 2 bits or 5 bits burst error) decoder control via I2C-bus (CCR910 and CCR912) or via extra input pins (CCR911) decoding of clock time and date information (CCR912 only). CCR921 features all R(B)DS group types supported simplified hard-software development for setmakers capable of storing last received R(B)DS blocks for 700 ms fast synchronization with block type A search error processing with correction status for every block decoder control via I2C-bus. decoder is always an I2C-bus slave - no multimaster bus required The following table gives a comparison of the four decoders. Table 24 CCR91xx data Characteristic supply voltage (VS) supply current CCR910 CCR911 CCR912 CCR921 5V 5V 5V 5V 24 mA 20 mA 24 mA 24 mA 4.332 MHz 8.664 MHz 6.664 MHz 8.664 MHz decoder control I2C-bus extra pins I2C-bus I2C-bus output prepared data via I2C-bus 3-wire bus I2C-bus I2C-bus oscillator frequency 2 I C-bus outputs: programme service name (group 0) programme identification (all groups) alternative freq. (group OA, method A+B) traffic programme (all groups) traffic announcement (groups 0 & 15B) programme type (all groups) decoder identification (groups 0 & 15B) music/speech (groups 0 & 15B) clock time PS PI AF TP TA PTY DI M/S output decoded data via extra pins: traffic programme traffic announcement music/speech synchronized RDS TP TA M/S TPN (active LOW) TAN (active LOW) M/SN (active LOW) TP TA M/S SYNC TP TA M/S SYNC based on microcontroller P83C652FFB P80CL51HFH P83C652FBB P83652FBB package QFP44, DIL40 QFP44 DIL40 QFP44 PS PI AF TP TA PTY DI M/S CT decoding is done by main C all RDS data available for main C continuous updating of RDS data RDS information decoding, collection and request information no real-time decoding operations for main C supports Enhanced Other Network supports RDS/RBDS 15 I2 C REQUEST RDDA signals from RDS demodulator I 2C-CLOCK CCR910 OSCI RDCL SYNC TP TA I2 C-DATA 2 additional outputs I C-address M/S A0 MGA532 - 2 A1 RDDA signals from RDS demodulator RDCL CCR911 OSCI RESET ECMD0 TPN TAN M/SN SYNCN switching outputs STAOUT CLKOUT DATOUT NEWSYN interface for main set controller/ tuning processor ECMD1 error correction mode setting MGA533 - 2 I2 C SYNC RDDA signals from RDS demodulator RDCL M/S CCR912 TA switching outputs TP OSCI MSC119 RQ to main set controller/tuning processor I2 C CTRQN RDDA signals from RDS/RBDS demodulator RDCL OSCI DAVN CCR921 additional outputs RESET SYNC TP TA M/S I 2C-CLOCK I 2 C-address A0 A1 I2 C-DATA MSC120 Fig.14 CCR9xx RDS and RDS/RBDS decoders 16 13. RADIO PC CARDS Philips has a range of radio PC card applications available based around the OM56xx family of radio tuners. These tuner modules are all fully shielded against the extreme electrical noise found within a PC and deliver clear, hi-fi quality FM stereo radio signals in a multimedia system. A user-friendly Windows-based program mimics the controls of a high-end system and gives the user full control over all the functions at the click of a mouse. Furthermore, designing the PC radio cards in a modular fashion, set makers can specify the feature they require, resulting in a single board design for various modes of the final radio. The most advanced system offers full R(B)DS capabilities and includes: CCR912 or CCR921 - R(B)DS decoder SAA6579T - R(B)DS demodulator OM56xx - FM stereo tune TEA6360T - audio preamplifier TEA6320 - sound processor TDA1517P - 2 x 6 W audio power amplifier ISA-bus interface. For more details about these components, refer to the relevant sections within this Designer's Guide. CCR921 R(B)DS DECODER SAA6579 RDS DEMODULATOR OM5604 FM MULTIMEDIA MODULE 75 aerial I2C-bus CD-ROM sound line input ISA-BUS INTERFACE TEA6320 SOUND PROCESSOR TDA1517P POWER AMPLIFIER power output line output TEA6360 5 BAND EQUALIZER MULTIMEDIA FM-RADIO CARD MSB943 Fig.15 Radio PC-card with R(B)DS PC radio features FM stereo radio with - search, step and preset tuning - AST (automatic storage of up to 100 presets) - local/DX switch - instalable search level - one-click precision manual tuning full R(B)DS capabilities, including PTY search and text display 5-band equalizer with 5 predefined and 4 user presets per source loudness filter 17 mute key separate line and power outputs with input level scaling 3-line inputs (e.g. CD audio, TV sound and auxiliary) master volume control simple CD player interface three versions available: - OM5604 for Europe: 87.5 to 108 MHz IEC-connector - OM5606 for USA: 87.5 to 108 MHz F-connector - OM5608 for Japan: 76 to 91 MHz F-connector. 14. DAB RECEIVER DAB Features supports DAB modes I, II & III key components comply with Eureka-147 supports all the main features of the EBU ETSI draft prETS 300 401 real-time processing of the fast information channel (FIC) and up to 6 service components error protection for audio and data services soft decision Viterbi decoder suitable for small DAB receivers. The key digital processing ICs are: FADIC - Differential demodulator and DSP interface The FADIC is frame independent and operates on a symbol basis. It is able to process all the symbols contained in the baseband frame, which it does in an identical way. Features input symbol buffering frequency transposition 2048-point, 512-point or 256point complex FFT differential demodulation metric generation four interfaces - an 8-bit parallel input interface - a 16-bit parallel control interface - an 8-bit parallel output interface - a boundary scan-test interface (IEEE 1149-1) DIGITAL MODULE TUNER MODULE Philips' DAB (Digital Audio Broadcast) concept contains all the key components for the Eureka-147 DAB system. The three main IC at the centre of the decoder are the FADIC, the SIVIC and SAA2501 or SAA2502. The complete chip-set supports all the main features of the ETS specification. RAM TUNER FADIC IF SAA2501 or SAA2502 SIVIC I2S CONTROL DSP MSB960 user interface Fig.16 DAB receiver Table 25 FADIC and SIVIC data Characteristic FADIC supply voltage (VS) SIVIC 5V 5V 1) total power dissipation 500 mW operating temperature range 0 to 70 C 0 to 70 C PLCC68 QFP64 package 350 mW 1) depending on the number of symbols processed SIVIC - Program selector The SIVIC performs service selection, frequency and time deinterleaving and Viterbi decoding. Features decoding of the fast information channel and up to 6 service components 4-bit soft decision Viterbi decoder, with a code rate 1/4 maximum decoding capacity of 320 Kbytes (excl. FIC) de-interleaving capacity maximum of 432 capacity units error flag generated by reencoding CRC syndrome calculation on each FIB five interfaces - a 4-bit parallel input interface - a serial output interface (DAB3) - a serial microcontroller interface (L3) - a 256K x 4 DRAM interface - a boundary scan-test interface (IEEE 1149-1) 18 SAA2501 - ISO/MPEG audio source decoder layer I and layer II combatable Eureka-147 combatable decoded sub-band signal output for concealment I2C interface processing of programme and audio service synchronized data L3 microcontroller interface SAA2502 - ISO/MPEG audio source decoder low sample frequency decoding possibilities (MPEG2 half sample frequencies) L3 and I2C-bus interface DAC output ( 256 times oversampled) 15. STANDARD AM/FM RADIO RECEIVER ICs The TEA5710(T), TEA5711(T) and TEA5712(T) are all highperformance, BiCMOS ICs for use in portable AM/FM radios. All necessary functions are integrated, from the AM & FM front end to the detector output stages, to make a complete radio. The TEA5710(T) design has new features to improve performance and tuning behaviour. Performance features include distributed selectivity on both AM and FM, and minimal variation with supply voltage. Tuning is improved by using a symmetrical AFC. The distributed IF gain allows a simple PCB layout. Furthermore, the AM/FM inputs and the varicon are referred to ground. A new aspect in AM reception is the high impedance AM RF input made by a differential MOST pair. This enables connection to the top of the input selectivity (e.g. the ferroceptor) which simplifies radio design and reduces the number of necessary switches in multiband radios. The TEA5711(T) and TEA5712(T) have all the features of the TEA5710(T). In addition, they also have a built-in stereo decoder with stereo blend controlled by field strength. They also feature a soft mute to suppress inter-station noise. The TEA5712(T) differs from the TEA5711(T) in that it is optimized for digital tuning systems: the AM/FM IF output signal is available for IF counting. Common features wide supply voltage range low current consumption high selectivity with distributed IF gain high input sensitivity good strong-signal behaviour (10 V/m AM, 500 mV FM) low output distortion simple, reliable PCB layout high impedance MOSFET input on AM. Specific features TEA5710(T) - LED driver for tuning indication TEA5711(T) - LED driver for stereo indication - soft mute - signal-dependent stereo - signal-level output TEA5712(T) - LED driver for stereo indication - soft mute - signal-dependent stereo - stop-signal output - IF output signals available for IF counting. The figure on the following page shows the FM performance of the of the TEA5711(T) and TEA5712(T). Table 26 Comparison of TEA5710(T), TEA5711(T) and TEA5712(T) Characteristic TEA5710(T) TEA5711(T) TEA5712(T) supply voltage (VS) 2.0 to 12 V 2.0 to 12 V 2.0 to 12 V supply current 7.5 mA 14 mA 14 mA AF output voltage (VO) 45 mV 45 mV 45 mV THD 0.8 % 0.8 % 0.8 % 1.6 mV/m 1.6 mV/m 1.6 mV/m supply current 9.0 mA 16 mA 16 mA AF output voltage (VO) 65 mV 65 mV 65 mV AM performance sensitivity (EMF for -3 dB limiting) FM performance THD 0.3 % 0.3 % 0.3 % sensitivity (EMF for -3 dB limiting) 1.2 V 1.2 V 1.2 V MPX performance channel separation package - 30 dB 30 dB SDIL24/SO24 SDIL32/SO32 SDIL32/SO32 Note: AM: frf = 1 MHz, m = 30 %, fmod = 1 kHz, VS = 3 V FM: frf = 100 MHz, f = 22.5 kHz, fmod = 1 kHz, VS = 3 V 19 0 VAF (dB) 0 dB = 65 mV -10 CS (dB) -20 MSC121 7 signal mute off mute on 4 stereo level noise 3 mono -50 2 THD (75 kHz) -60 -70 10-1 THD (%) 5 CS (75 kHz) -30 -40 level (A x 100) 6 frf = 100 MHz fmod = 1 kHz f = 22.5 kHz VS = 3 V 1 THD (22.5 kHz) 1 10 102 103 104 Fig.17 FM performance of the TEA5711(T)/12(T) 20 105 Vin1 (V) 0 106 16. SELF-TUNED AM/FM RADIO IC The TEA5757H IC is single-chip, self-tuned radio (STR). It contains a complete AM/FM receiver, stereo decoder, self-tuning VCO, stop circuitry and bus interface. As such it perform all the functions from the aerial input to the stereo decoder outputs. The tuning concept used in the IC combines the advantages of manual tuning with the facilities and features associated with electronic tuning. This is because of the inherent fuzzy logic behaviour of the STR which mimics manual tuning (course tuning followed by fine tuning) and achieves fast and reliable tuning to the desired frequency. The STR searches for strong signals and allocates them to preset channels, typically identifying 40 stations within just 20 seconds. When the station is selected the signal is locked and the IC goes into a standby mode. If at any time the quality of the signal weakens, the chip "wakes up" and fine-tunes itself again. Also, local/DX switching ensures reception is not overpowered when tuned to a strong local transmitter. RECEIVER INTERFACE AM VCO AM AFC AM CHANNEL LEVEL V/I A/D level FM AFC FM CHANNEL bus DIGITAL CONTROL & TUNING FUNCTION ref. osc. Sout DET. FM VCO MPXin Cloop FM STEREO DECODER SDS TEA5757H STABILIZER MSB961 L audio R Fig.18 TEA5757H self-tuned radio Table 27 TEA5757H data Characteristic Value static supply voltage (VCC1) 2.2 to 12 secondary supply voltage for tuning (VCC2) supply current (IVCC1) AM FM tuning voltage 12 12 to 18 mA 13 to 19 mA 0.7 to VCC2 - 0.75 V AM performance frequency range RF sensitivity AF output voltage total harmonic distortion 0.144 to 30 MHz 40 to 70 V 36 to 70 mV 0.8% FM performance frequency range RF sensitivity AF output voltage total harmonic distortion 50 to 150 MHz 0.4 to 3.8 V 40 to 57 mV 0.3% MPX performance channel separation package Features AM receiver (LW, MW and SW) FM stereo receiver tuning synthesizer and radio on one chip stop detection circuitry microcontroller bus interface manual-search, auto-search, auto-store and preset-mode TUNING 30 dB QFP44 (SOT307) few external components required high input sensitivity low output distortion tuning is independent of the channel spacing low power consumption due to standby mode. 21 Two other derivatives of the TEA5757H are also available: the TEA5759H for Japanese frequency ranges, and the TEA5762H with external FM frontends for CENELEC applications. 17. AUDIO AMPLIFIER ICs The tables below gives an overview of our audio amplifier ICs for portable and mains-powered radio/audio systems. For more details on each type, refer to our publication Design-in guide: Audio amplifier ICs, ordering code 9398 706 66011. Table 28 Audio amplifiers for portable systems Type No. TDA1016 Po (W) Supply (V) Package Remarks 2 3.6 to 15 DIL16 record/playback + ALC 2 x 0.06 (dtot = 0.1%) 3 to 7 SO8 stereo headphone driver TDA7050 [0.15]/2 x 0.075 1.6 to 6 SO8 no peripheral components TDA7050T TDA1308T [0.15]/2 x 0.075 1.6 to 6 DIL8 no peripheral components TDA7052 1 3 to 18 DIL8 no peripheral components TDA7053 2x1 3 to 18 DIL16 no peripheral components 1 4.5 to 18 DIL8 DC volume control; 35.5 dB gain 0.5 4.5 to 18 SO8 DC volume control; 35.5 dB gain 1 4.5 to 18 DIL8 DC volume control; 40 dB gain 0.5 4.5 to 18 SO8 DC volume control; 40 dB gain 2x1 4.5 to 18 DIL16 DC volume control; 40 dB gain 2 x 0.5 4.5 to 18 SO16 DC volume control; 40 dB gain 3 3 to 18 SIL9 no peripheral components; 39 dB gain TDA7057Q 2x3 3 to 18 SIL13 no peripheral components; 39 dB gain TDA7056A 3 4.5 to 18 SIL9 DC volume control; 35.5 dB gain TDA7056B 5 4.5 to 18 SIL9 DC volume control; 40 dB gain 2x5 4.5 to 18 SIL13 DC volume control; 40 dB gain 1 2.2 to 18 SO8, DIP8 BTL amplifier with standby/mute logic TDA8542(T) 2x1 2.2 to 18 SO16, DIP16 BTL amplifier with standby/mute logic TDA8559(T) 2 x 0.35 1.8 to 30 SO16, DIP16 low-voltage stereo headphone amplifier TDA7052A TDA7052AT TDA7052B TDA7052BT TDA7053A TDA7053AT TDA7056 TDA7057AQ TDA8541 Note: Output powers are RMS and quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker impedance. Figures in brackets are for higher loudspeaker impedance. Table 29 Audio amplifiers for mains-powered systems Type No. Po (W) Supply (V) Package Remarks 50 (d = 0.1%) 15 to 60 SIL9 mono 1-end amp., super hi-fi, 20 - 46 dB gain TDA1517(P) 2x6 8.5 to 18 SIL9 20 dB gain TDA1521(Q) 2 x 12 (d = 0.5%) 15 to 42 SIL9, DBS9 automatic mute; hi-fi TDA1521A 2 x 6 (d = 0.5%) 15 to 42 SIL9 automatic mute; hi-fi TDA1560Q [40] 8 to 18 DBS17 BTL class-H amplifier, [30]dB gain TDA1561Q 2 x 23 8 to 18 DBS13 SE-BTL power amplifier TDA2611A 4 to 10 6 to 35 SIL9 adjustable input impedance 6 (d = 0.5%) 15 to 42 SIL9 automatic mute; hi-fi TDA2614 6 (d = 0.5%) 15 to 42 SIL9 TDA2613 with extra mute pin TDA2615 2 x 6 (d = 0.5%) 15 to 42 SIL9 TDA1521A with extra mute pin TDA2616(Q) 2 x 12 (d = 0.5%) 15 to 42 SIL9, DBS9 TDA1521(Q) with extra mute pin TDA8577 dual line receiver 5 to 18 SIL9 completely separated inputs TDA8578(T) dual line receiver 5 to 18 DIL16, SO16 completely separated inputs TDA8579(T) dual line receiver 5 to 18 DIL8, SO8 inverting inputs linked TDA1514A TDA2613 Note: Output powers are RMS and quoted at THD = 10% unless stated otherwise and depend on supply voltage and loudspeaker impedance. Figures in square brackets refer to performance in BTL configuration. 22 18. PLL FREQUENCYSYNTHESIZER ICs Our AM/FM PLL synthesizer range for radio tuning systems comprises three I2C-bus controlled ICs: TSA6057(T)/60(T)/61(T). All these ICs have sensitive prescalers and receive VCO signals directly from AM and FM tuners. Their loop gain can be bus-controlled to combine fast search tuning with stable locking. The two-loop amplifiers allow the loop characteristics to be independently set for AM and FM. Some of them incorporate an inlock detector. Common features on-chip, high input-sensitivity AM & FM prescalers on-chip, high-performance 1 input (2 output) tuning voltage amp. for AM & FM loop filters high-speed tuning due to a powerful digital memory phase detector serial 2-wire I2C-bus. TSA6057(T) specific features on-chip 2-level current amplifier (charge pump) to adjust loop gain 1 reference oscillator (4 MHz) for both AM & FM 40 kHz output reference frequency for FM IF system & microcomputer based tuning interface oscillator frequency ranges of 512 kHz to 30 MHz, 30 to 150 MHz 3 selectable reference frequencies for both tuning ranges (1, 10, 25 kHz) software-controlled bandswitch output. TSA6060(T) specific features on-chip 2-level current amplifier (charge pump) to adjust loop gain 1 reference oscillator (8 or 4 MHz) for both AM & FM 40 kHz output reference frequency for FM IF system & microcomputer based tuning interface oscillator frequency ranges of 512 kHz to 30 MHz, 30 to 200 MHz 4 selectable reference frequencies for both tuning ranges (1, 10, 25, 50 kHz) software-controlled bandswitch output in-lock detector output pin. Table 30 Comparison of TSA6057(T) and TSA6060(T) Characteristic TSA6057(T) TSA6060(T) supply voltage (VS) 4.5 to 5.5 V 4.5 to 5.5 V frequency range of AM prescaler 0.5 to 30 MHz 0.5 to 50 MHz frequency range of FM prescaler 30 to 150 MHz 30 to 200 MHz frequency divider programmable: swallow counter: 13 bits 4 bits 17 bits reference oscillator pins: frequency: 2 4 MHz 1 4/8 MHz 1,10,25 kHz 1,10,25,50 kHz I2C I2C reference frequencies control bus separate loop amplifier outputs AM/FM AM/FM 5 A; 500 A 50 A; 500 A in-lock detector output - wired IF counter for 10.7 MHz AM/FM & 450 kHz AM - - 6-bit ADC - - 1 output 1 output DIL16, SO16 DIL16, SSOP20 charge pump current (CP=0; CP=1) ports 40 kHz reference output package 23 40 kHz reference output AM VCO input prescaler decoupling FM VCO input PRESCALER +3, +4 MULTIPLEXER PRESCALER +3, +4 13-BIT PROGRAMMABLE DIVIDER DIGITAL PHASE DETECTOR 3-1 MULTIPLEXER REFERENCE COUNTER IN LOCK DETECTOR 4-BIT SWALLOW COUNTER VCC1 VEE REFERENCE OSCILLATOR POWER SUPPLY INLCK VCC2 FM / AM SWITCH FREQUENCY LATCHES PROGRAMMABLE CURRENT AMPLIFIER AM output for external loop filter tuning voltage amplifier input AM / FM SWITCH serial data input reference oscillator FM output for external loop filter I 2 C-BUS CONTROL serial clock input BAND SWITCH TSA6057(T) bandswitch output AS MSC122 Fig.19 TSA6057(T) PLL frequency synthesizer 40 kHz reference output AM VCO input prescaler decoupling MULTIPLEXER 17-BIT PROGRAMMABLE DIVIDER DIGITAL PHASE DETECTOR 3-1 MULTIPLEXER REFERENCE COUNTER FM VCO input REFERENCE OSCILLATOR IN LOCK DETECTOR reference oscillator INLCK VCC2 FM / AM SWITCH VCC1 VEE POWER SUPPLY FREQUENCY LATCHES PROGRAMMABLE CURRENT AMPLIFIER tuning voltage amplifier input AM / FM SWITCH serial data input serial clock input AM output for external loop filter FM output for external loop filter I 2 C-BUS CONTROL TSA6060(T) BAND SWITCH AS MGA522 Fig.20 TSA6060(T) PLL frequency synthesizer 24 bandswitch output 19. DOLBY NOISEREDUCTION ICs TEA0665(T) SWITCHING LOGIC TEA0665(T) Dolby B/C IC This IC is designed for use in Dolby B and Dolby C type audio noise reduction (NR) systems. It provides the high and low level stages for one channel of a Dolby C type NR system, including NR on/off switching and all electronic switching necessary for Dolby C type systems. In addition the TEA0665 includes a preamplifier for the record and playback functions and a multiplex buffer amplifier. The circuit offers two different line-output levels (-6 & 0 dBm) and a low-pass filter, which can be fed into the signal path in playback mode. The TEA0665 comes in a SOT117 28-lead plastic DIL package. The TEA0665T comes in a surface-mount 28-lead mini-pack (SO28; SOT136A). POWER SUPPLY DOLBY B/C NR PLAY in SWITCHING REC in REC/PLAY ON/OFF DOLBY B/C HIGHLEVEL STAGE LOWLEVEL STAGE REC out MSC123 line output 1 line output 2 Fig.21 The TEA0665(T) Dolby B/C noise reduction circuit FILTER P R REC in output channel B DOLBY B NR PLAY in P TEA0657 SWITCHING REC/PLAY NR ON/OFF POWER SUPPLY P PLAY in output channel A DOLBY B NR REC in R R Features few external components includes record/play preamplifiers plus multiplex filter buffer amplifier two line-output levels all electronic switching. CHANNEL B R CHANNEL A P FILTER MSC124 Fig.22 The TEA0657 Dolby B noise reduction circuit Table 31 TEA0665(T) and TEA0657 data TEA0657 Dolby B IC This IC provides two channels of Dolby B noise reduction. The circuit contains all internal electronic switching to provide playback or record functions. In addition, the TEA0657 includes preamplifiers for the playback and record modes and multiplex filter buffers for both channels. The IC will operate with power supplies ranging from 9 to 15 V, output overload level increasing with supply voltage. Current drain varies with supply voltage and noise reduction on/off, so it is advisable to use a regulated power supply or a supply with a long time constant. Characteristic TEA0665(T) TEA0657 supply voltage (VS) 8.0 to 16.0 V 9.0 to 15.0 V supply current (typ.) 17 mA 19 mA signal + noise to noise ratio record mode: playback mode: 66 dB 66 dB 72 dB 90 dB DIL28 (SOT117)/ SO28 (SOT136A) DIL24 (SOT101B) package The TEA0657 comes in a 24-lead DIL plastic package (SOT101B). Features dual NR channels full playback/record switching separate playback/record inputs 25 multiplex filter buffers simultaneous switching on both channels dual or single supply operations Dolby reference level = 580 mV input sensitivity = 30 mV. 20. MICROPROCESSOR CONTROL AND DISPLAY Over the years, the continually expanding range of Philips' ICs for radio and audio has allowed set manufacturers to implement remote control and extend microcomputer control to virtually all the functions of a radio and hifi system. This has led to incorporation of many new facilities such as electronic tuning with search facilities, preset station selection, digital frequency indication and operation in conjunction with Radio Data System (RDS) information. Microprocessor control To assist audio equipment manufacturers incorporate computer control into their circuit designs, Philips supply one of the widest available ranges of 8-bit CMOS microcontroller derivatives. All are based on the industry standard 8051, with architectural enhancements that make them suitable for radio and hi-fi control systems. They all include an EEPROM I 2 C-bus I 2 C-bus LCD DRIVER EEPROM MICROCONTROLLER WITH LCD DRIVE MICROCONTROLLER WITHOUT LCD DRIVE LCD MGA503 LCD Fig.23 Typical radio control and display systems 80C51 CPU, use the 80C51 instruction set, and have a wide variety of on-chip peripheral functions; expansion of I/O lines, A to D conversion, I2C-bus interface, expanded program ROM and data RAM, watchdog timer, UART, 16-bit timer/event counters, and on-chip oscillator and timing circuits. Our microcontrollers are supported by a range of 1K to 8K CMOS static EEPROMs. Most of these non-volatile memories have an I2C-bus interface and unique Philips' circuitry for improving reliability by correcting single-bit failures. Display drivers To simplify the user interface of hi-fi equipment, it is necessary to have a multitude of parameters displayed by LCD segments. Examples of such displays are tuning information, analog control settings, RDS/RBDS functions, CD and tape information etc. Philips' extensive range of I2Cbus controlled LCD drivers are ideal for driving LCD segments or dot-matrix LCD graphics panels either directly or at multiplex rates up to 1:4 (segment displays) or 1:32 (dot-matrix displays). Table 32 Features of microcontrollers with LCD drive P83CL434 P83CL834 ROM capacity 4 Kbytes 8 Kbytes RAM capacity 128 bytes supply voltage 256 bytes 3.3 to 5.5 V I/O ports 12 pins clock frequency 0.7 to 12 MHz 1 second interrupt power-on reset timers 2 LCD driver 22-24 segments 1-4 backplanes packages DIP42, QFP44 26 Table 33 Features and performance of microcontrollers without LCD drive Type number ROM capacity (Kbytes) RAM capacity (bytes) Timers I/O ports Serial interfaces Frequency range (MHz) P83C750 1 64 1 2-3/8 - 3.5 to 40 P83C748 2 64 1 2-3/8 - 3.5 to 16 P83C749 2 64 1 2-5/8 - 3.5 to 16 P83C751 2 64 1 2-3/8 I2C 3.5 to 16 2 P83C752 2 64 1 2-5/8 IC 3.5 to 16 P80CL51 4 128 2 4 UART 0 to 16 P80C51 4 128 2 4 UART 1.2 to 30 P83CL410 4 128 2 4 I2C 0 to 12 P83C451 4 128 2 7 UART 3.5 to 16 P83C550 4 128 2 + watchdog 4 UART 3.5 to 16 P83C851 4 128 2 4 UART Special features low voltage low voltage 8-input ADC 1.2 to 16 2 P83CL580 6 256 3 + watchdog 5 UART, I C 0 to 12 P80C52 8 256 3 4 UART 3.5 to 24 2 low voltage P83C552 8 256 3 + watchdog 6 UART, I C 1.2 to 30 8-input ADC P83C562 8 256 3 + watchdog 6 UART 1.2 to 16 8-input ADC P83C652 8 256 2 4 2 1.2 to 24 2 UART, I C P83C524 16 512 3 + watchdog 4 UART, I C 1.2 to 16 P83CE654 16 256 2 4 UART, I2C 1.2 to 24 EMC optimized, 8-input ADC P83C654 16 256 2 4 UART, I2C 1.2 to 24 8-input ADC P83CL781 16 256 3 4 UART, I2C 0 to 12 low voltage 2 0 to 12 low voltage 2 P83CL782 16 256 3 4 UART, I C P83C528 32 512 3 + watchdog 4 UART, I C 1.2 to 16 P83CE528 32 512 3 + watchdog 4 UART, I2C 1.2 to 16 EMC optimized 2 P83CE558 32 1024 3 + watchdog 6 UART, I C 1.2 to 16 EMC optimized, 8-input ADC, PLL oscillator 32 kHz reference P83CE598 32 512 3 + watchdog 6 UART, CAN 1.2 to 16 EMC optimized, 8-input ADC P89CE558 32 1024 3 + watchdog 5 UART, I2C 3.5 to 16 EMC optimized, flash EEPROM, PLL oscillator 32 kHz reference P83CE559 48 1536 3 + watchdog 6 UART, I2C 1.2 to 16 EMC optimized 27 Table 34 Features and performance of CMOS static EEPROMs with I2C-bus interface Type number Capacity Temp. range (K bit) (C) Supply voltage (V) -40 to +85 4.5 to 5.5 PCF8581(T) PCF8581C(T) 1 -40 to +85 Error correction Write cycles over temp. range Write cycles at 22 C Package 104 105 DIL8 (SO8) 4 5 DIL8 (SO8) 6 2.5 to 6 10 10 5 PCF8582C-2(T) -40 to +85 2.5 to 6 10 10 DIL8 (SO8) PCD8582D-2(T) -25 to +70 3 to 6 104 105 DIL8 (SO8) 4 5 DIL8 (SO8) 6 DIL8 (SO8) PCF8582E-2(T) 2 -40 to +85 4.5 to 5.5 10 PCA8582F-2(T) -40 to +125 4.5 to 5.5 10 PCA8522E(T) -40 to +85 2.7 to 5.5 105 PCF8594C-2(T) -40 to +85 PCD8594D-2(T) PCF8594E-2(T) 4 PCA8594F-2(T) 10 DIL8 (SO8) 5 2.5 to 6 10 6 DIL8 (SO8) 5 10 4 -25 to +70 3 to 6 10 10 DIL8 (SO8) -40 to +85 4.5 to 5.5 104 105 DIL8 (SO8) 4.5 to 5.5 5 6 DIL8 (SO8) -40 to +125 PCA8524E(T) 10 5 -40 to +85 10 10 5 2.7 to 5.5 10 DIL8 (SO8) 5 6 PCF8598C-2(T) -40 to +85 2.5 to 6 10 10 DIL8 (SO8) PCD8598D-2(T) -25 to +70 3 to 6 104 105 DIL8 (SO8) 4 5 DIL8 (SO8) 6 DIL8 (SO8) PCF8598E-2(T) PCA8598F-2(T) 8 -40 to +85 -40 to +125 4.5 to 5.5 10 10 5 4.5 to 5.5 10 10 Table 35 Features and performance of the LCD segment drivers with I2C-bus interface Type number PCF8566(T) PCF8576T PCF8576C PCF8577C(T) 24 40 40 32 1:1, 1:2, 1:3, 1:4 1:1, 1:2, 1:3, 1:4 1:1, 1:2, 1:3, 1:4 1:1, 1:2 Segments driven per IC 96 40 40 32 Max. ICs per system 16 16 16 8 1536 2560 2560 512 V 2 to 6 2 to 9 2 to 6 2.5 to 9 A A 90 40 180 60 120 60 250 bits 24 x 4 40 x 4 40 x 4 Hz 0.5, 1, 2 0.5, 1, 2 0.5, 1, 2 DIL40, VSO40 VSO56 VSO56, LQFP64 Segment drive outputs Multiplex rate Max. segments driven per system Supply voltage Max. supply current: operating at 5 V power saving mode Display data RAM Blinking modes Package 28 DIL40, VSO40 21. REMOTE CONTROL CIRCUITS In the past, insufficient command capacity of remote controllers and non-standardization of commands and protocols made it impossible to operate all remotely controlled equipment from a single remotecontrol handset. To solve this problem, Philips has developed a remote control protocol (RC-5) and the ICs to support it. The RC-5 protocol provides unified remote control of consumer equipment. It can handle up to 4096 commands organized as two sets of 64 commands in 32 individually addressable groups, each of which can be allocated to a separate unit or system. Since many of the 128 commands can control the same function in each different pieces of equipment (e.g. a tuner or an amplifier), RC-5 allows a single remote control handset with relatively few keys to control any individual item of equipment or an entire integrated system. Obviously, to ensure that there are no spurious responses to commands given to items of equipment from different manufacturers, it is essential to have some degree of standardization in the allocation of system addresses and command codes. This standardization, and a procedure for the allocation of new or additional codes, already exists within Philips and is available to our customers. Remote control system architecture The remote control system consists of an infrared transmitter, CONSUMER EQUIPMENT CENTRAL MICROCONTROLLER RECEIVER LOCAL KEYBOARD TRANSMITTER REMOTE CONTROL keyboard 8x8 MBA855 Fig.24 Typical remote control system a receiver, and decoding software in the central microcontroller of the equipment being controlled. The transmitter is a dedicated PCA84CX22 microcontroller for the required digital data output. A biphase-coded bitstream modulates a 36 kHz carrier which is subsequently converted into an infrared signal by an IR LED. At the receiving end, the infrared signal from the transmitter is detected, demodulated, amplified and filtered. If local control is required, amplified output from the keyboard scanner is passed directly to the central microcontroller of the equipment for decoding. PCA84CX22 - remote control transmitters Philips' PCA84CX22 family of transmitters are dedicated lowvoltage, stand-alone 8-bit microcontrollers that can be mask- 29 programmed to generate the control command codes in accordance with the RC-5 protocol or any other protocol of a set manufacture's choice. Each contains an 84CXXX CPU with ROM, RAM and the following additional on-chip peripherals: interrupt gate modulator for providing adjustable pulse bursts, pulse duration and pulse duty factor watchdog timer to prevent malfunction or the transmitter being locked 8-bit programmable timer/event counter with 5-bit prescaler 1 Mhz to 6 Mhz oscillator. Input/output expanders We also have two I/O expanders to complement our remote control ICs - the PCF8574(A) and the SAA130. These two ICs provide remote I/O expansion for most microcontrollers via the I2C-bus. 22. MPEG ICs The perceptual audio encoding/ decoding scheme defined within the ISO/IEC MPEG-1 (Motion Picture Expert Group) Audio Standard (11172-3) results in considerable reduction of the quantity of data required for digital audio, yet maintains a high level of perceived sound quality. The coding is based on a psychoacoustic model of the human auditory system and exploits the fact that weak spectral components are inaudible if they are in the proximity (in both time and frequency) of loud components. This phenomenon is called masking. Layers I and II of ISO/MPEG-1 reduce the data by splitting the broadband audio source signal into 32 sub-bands of equal width. The masking threshold (the amount of imperceptible audio energy as a function of frequency) is determined for the given signal by using the psycho-acoustic model. The sub-band samples are then re-quantized to an accuracy that ensures that the spectral distribution of the re-quantization noise does not exceed the masking threshold. This reduction of representation accuracy provides the reduction of the audio data. The re-quantized sub-band samples are multiplexed with side information concerning the actual re-quantization to form the MPEG audio bitstream. During decoding, the MPEG audio bitstream is de-multiplexed and the side information is used to reconstruct the sub-band signals which are combined to form a broadband audio output signal. We have two MPEG audio decoders suitable for hi-fi systems: a Digital audio broadcast decoder (SAA2501H) and an MPEG-1/2compatible audio decoder (SAA2502H). Depending on features (see below), both products are ideally suited for use in ADR and DAB receivers. Table 36 Comparison of SAA2501H and SAA2502H Type number SAA2501H SAA2502H 5 10% V 5 10% V QFP44 QFP44 ISO/MPEG audio source decoder Layer I and Layer II compatible Suitable for DAB (Eureka-147 compatible) Decoded sub-band signal output for concealment Processing of programme and audio service synchronized data Dynamic range control MPEG 2 compatible (for stereo output) Handles byte- and non-byte-aligned input data I 2C microcontroller interface IEC 958 digital output Integrated DAC 256 x fs clock locked to external reference I 2S interface Low power consumption L3 microcontroller interface Clock generator Microcontrolled and stand-alone modes Error concealment Burst mode data input Stereo Sample clock switching Variable bit precision Supply voltage Package 30 URDA L3CLK STOP L3MODE L3DATA FSCLKM FSCLK FSCLK384 FSCLKIN X22IN CLOCK GENERATOR DECODING CONTROL RESET SAA2501H SYNTHESIS SUBBAND FILTER BANK & OUTPUT PROCESSOR DEQUANTISATION & SCALING PROCESSOR SD SCK WS FDA1 FDA0 MSB467 FDEF TC0 CDM CDMEF CDMCL CDMWS FDFSY INPUT PROCESSOR TC1 CDS CDSEF CDSCL CDSWA CDSSY X22OUT MCLK MCLK24 MCLKIN MCLKOUT TDI TDO TCK TMS TRST Fig.25 SAA2501H digital broadcast decoder PC MCLKIN MCLKOUT X22OUT X22IN L3MODE DIVIDER REF-CLK CLOCK GENERATOR PHASE COMPARATOR DECODING CONTROL L3/I 2C CLOCK L3DATA/I2 CDATA FSCLKIN FSCLKOUT URDA/STOP CDSCL/CDMCL CDSEF/CDMEF analogue right DEQUANTIZATION CDS/CDM DAC analogue left I/P PROCESSOR SD SYNTHESIS CDSWA/CDMWS CDSSY SPDIF ENCODER SAA2502H TC1 TC0 TD1 TD0 TCK TMS TRST SPDIF RESET Fig.26 SAA2502H MPEG-1/2- compatible audio decoder 31 WS SCK MSB515 23. DIGITAL SIGNAL PROCESSING ICs Our digital signal processing (DSP) ICs comprise the SAA7740H DSP IC, the SAA7710T Dolby Pro Logic DSP, and two DACs with DSP features: the TDA1546T and TDA1548T. SAA7040H Digital Audio Processing IC This is a very flexible functionspecific 4-channel DSP for audio signals. In the general mode, it can provide listening environment enhancements such as equalization, concert hall-effects, reverberation, surround sound/ karaoke processing, and digital volume/balance control. In the dual/quad filter modes, the IC can also be reconfigured as a dual or quad digital filter with programmable frequency characteristics. A stereo expansion mode provides stereo digital filtering, 5-band graphic equalization and complex stereo expansion for headphone out-of-head and incredible stereo applications. Function parameters, correction coefficients and a number of configurations can be downloaded to the IC via an I2C-bus interface. Features two digital audio inputs and outputs in the I 2S format independent input and output interfaces slave input and output interfaces I 2C microcontroller interface DC filtering at the inputs CLOCK COUNTER XTAL DIW DID 2 I2 S-BUS INPUT INPUT BUFFER DIC DIGITAL SIGNAL PROCESSING CORE 2nd-ORDER FILTER MAC OFFSET FILTER REGISTERS 16 PROGRAM COUNTER PROGRAMMABLE ROM DOW 2 I2 S-BUS OUTPUT OUTPUT BUFFER DOD DOC 16 7 COEFFICIENT RAM A0 to A8 ADDRESS CONTROL UNIT DRAM D0 to D3 16 SAA7740H SCL SDA I 2 C-BUS INTERFACE MSB469 Fig.27 SAA7740H Digital audio processing IC Table 37 SAA7740H data Characteristic SAA7740H typical crystal frequency supply voltage (VS) total supply current (fc = 16.9344 Mhz) total power dissipation (fc = 16.9344 Mhz) operating temperature range package 16.9344 MHz 4.5 to 5.5 V 145 mA 700 mW -40 to +85 C QFP64 one programmable 2nd-order digital filter unit 5-band parametric equalizer with selectable centre freq., slope and boost/cut gain settings of 12 dB External delay-line processing for delays of up to 1 s Reverberation with selectable reverberation time (up to 5 s) and energy Three different surround sound programs to obtain a spatial effect with four loudspeakers 32 Passive Dolby surround sound processing, with addition of an external dynamic noise reduction IC stereo width control from mono to stereo to spatial stereo stereo listening environment acoustic effects (e.g. concert hall) with 8 coefficients and 8 delayed taps per channel digital volume and balance control Soft-controlled soft mute/demute via the microcontroller interface. SAA7710T Dolby Pro Logic surround sound circuit This is a high-quality audioperformance add-on digital signal processor. It comprises all the necessary features on chip for complete Dolby Surround Pro Logic sound. In addition, the device also incorporates 3- and 5-band parametric equalizers, and tone and volume controls. These features can be used to replicate surround sound as an alternative to Dolby Pro Logic, or when the input is non-Dolby surround coded. Features adaptive matrix 7 kHz low-pass filters adjustable delay for surround channel modified Dolby B noise reduction noise sequencer output volume control automatic balance and master level control with DC-offset filter hall and matrix surround sound functions Either: - 3-band parametric equalizer on main channels left, centre, right (fs = 44.1 kHz), or - 5-band parametric equalizer on main channels left, centre, right (fs = 32 kHz), or - tone control (bass/treble) on all four output channels (fs = 44.1 kHz) optional clock divider for crystal oscillator I2C-bus mode control SAA7710 AUTO BALANCE FUNCTION L IIS_DATAIN1 DOLBY PRO LOGIC OR HALL/MATRIX SURROUND IIS inputs IIS_DATAIN2 C R SURROUND CHANNEL DELAY LINE CONTROL DSP_RESET L/R 3- OR 5-BAND PARAMETRIC EQUALISER OR TONE CONTROL IIS_DATAOUT1 C/R IIS_DATAOUT2 IIS outputs IIS_DATAOUT3 (not used) S IIC BUS TRANSCEIVER OSC. MGC727 DSP_IN1 SDA DSP_IN2 DSP_OUT1 DSP_OUT2 SCL AD XTAL OSC Fig.28 SAA7710T Dolby Pro Logic surround sound IC Table 38 SAA7710T data Characteristic SAA7710T supply voltage (VS) 4.5 to 5.5 V on-chip delay line (fs = 44.1 khz) 45 mA 4-channel active surround sound 20 to 20 000 Hz stereo I2C digital input channels 2 2 stereo I C digital output channels package 2 SO32 33 TDA1546T and TDA1548T Bitstream/CC filter-DACs These filter-DACs feature a unique combination of bitstream and continuous calibration techniques. The DAC functions as a bitstream converter for low-level signals, and as a dynamic continuous calibration converter for large signals. This technique results in low power consumption, a small chip and simple application. These DACs include upsampling filtering and noiseshaping. The combination of high oversampling up to 16fs, secondorder noise-shaping and continuous calibration ensures that only simple 1st-order analog postfiltering is required. These DACs accept input in I2S format or Japanese format with word lengths of 16, 18 and 20 bits. Four cascaded filters increase the oversampling rate to x16. A sample-and-hold function increases the oversampling rate in normal speed mode to x96 (fsys = 384fs) or x128 (fsys = 256fs) or to x48 (fsys = 256fs) or x64 (fsys = 384fs). A 2nd-order noise shaper converts this oversampled data into a bitstream. The DACs incorporate special data encoding. This ensures an extremely high signal-to-noise ratio, superior dynamic range, and immunity to process variations and component ageing. Table 39 TDA1546T and TDA1548T data Characteristic TDA1546T TDA1548T single supply voltage 3.8 to 5.5 V 2.7 to 4 V power dissipation 265 mW 50 mW -88(0.004) dB(%) -85(.0056) dB(%) -44(0.6) dB(%) -35(1.179) dB(%) 108 dB 95 dB Full-scale output voltage (RMS value) 1.5 V 0.7 V Selectable system clock 256, 384 xfs 256, 384, 64 xfs 128 96 64 48 128 96 64 48 I 2S, "S" 1fs, 16, 18 or 20-bit I 2S, "S" 1fs, 16, 18 or 20-bit SO28 SO28 typ. THD + N at full-scale (0 dB) typ. THD + N at -60 dB (A-weighting) Typical signal-to-noise-ratio (A-weighting) x oversampling: normal speed (fsys = 256fs) normal speed (fsys = 384fs) double speed (fsys = 256fs) double speed (fsys = 384fs) Serial input format package Two on-chip operational amplifiers convert the DAC output currents into voltages. Externallyconnected capacitors perform the required 1st-order post filtering. No further filtering is required. The unique combination of bitstream and continuouscalibration techniques, together with a high degree of analog and digital integration, results in a single-filter DAC with 18-bit dynamic range, high linearity, and simple, low-cost application. 34 Common features simple application continuous calibration DAC combined with the bitstream technique cascaded 4-stage digital filter incorporating 2-stage FIR filter, linear interpolator and sample and hold DSP features (digital volume and tone control) master or slave mode clock system smoothed transitions before and after muting (soft mute) noise shaper no zero crossing distortion. BCK WS DATA CKSL MULTIPLE INPUT FORMAT CRYSTAL OSCILLATOR XTAL1 DE-EMPHASIS SPECTRUM ANALYSER PEAK DETECTION SILENCE DETECTION OVERLOAD DETECTION VERS1 SOFT MUTE TONE CONTROL 1 BASS TONE CONTROL 2 TREBLE VERSATILE OUTPUT VERS0 CDEC CLOCK & GENERATION DISTRIBUTION SOURCE SELECTION VOLUME CONTROL BALANCE dB CONVERTER TONE CONTROL 3 BASS BOOST V SSd V DDd MICROPROCESSOR INTERFACE FIR FILTER STAGE 1 : 1FS - 2FS TEST1 FIR FILTER STAGE 2 : 2FS - 4FS TEST2 FIR FILTER STAGE 3 : 4FS - 8FS LIN. INTERPOLATOR 8FS - 16 FS 8x OVERSAMPLING (SAMPLE & HOLD) 2nd ORDER NOISE SHAPER DATA ENCODER LEFT OUTPUT SWITCHES XTAL2 VDDx VSSx POR L3DATA L3CLK L3MODE LIN. INTERPOLATOR 8FS - 16 FS 8x OVERSAMPLING (SAMPLE & HOLD) 2nd ORDER NOISE SHAPER DATA ENCODER RIGHT OUTPUT SWITCHES FILTCR FILTCL RCONV1 1 nF 2.2 k C EXT1 VOL 16 (4-bit) CALIBRATED CURRENT SOURCES 16 (4-bit) CALIBRATED CURRENT SOURCES R CONV2 1 nF C EXT2 2.2 k OP1 VOR OP1 16 (4-bit) CALIBRATED CURRENT SINKS V REF 16 (4-bit) CALIBRATED CURRENT SINKS 1 F TDA1546T REFERENCE SOURCE GND VSSO VDDO V DDA MSB471 V SSA Fig.29 TDA1546T bitstream/continuous calibration filter-DAC IF1 IF2 DATA WS BCK MUTE SERIAL DATA INPUT DEEM VOLUME AND SOUND CONTROL VOLUME CONTROL SYSCLK SOFT MUTE CONTROL TIMING AD3S ADVC ADBB CLSEL ADTR SOUND CONTROL 1 FS V DDA FILTER STAGE 1 2 FS MODE0 OP FILTER STAGE 2 MODE1 ADREF 4 FS LINEAR INTERPOLATOR 8 FS IOL RCONV1 1 nF GND 8 x OVERSAMPLING (SAMPLE-AND-HOLD) 8 x OVERSAMPLING (SAMPLE-AND-HOLD) 2nd ORDER NOISE SHAPER 2nd ORDER NOISE SHAPER DATA ENCODER DATA ENCODER V SSD VDDD 16 (4-bit) CALIBRATED CURRENT SOURCES 16 (4-bit) CALIBRATED CURRENT SOURCES LEFT OUTPUT SWITCHES RIGHT OUTPUT SWITCHES 2.2 k C EXT1 VOL OP1 VDDO V REF IOR R CONV2 1 nF C EXT2 2.2 k VOR OP1 REFERENCE SOURCE 16 (4-bit) CALIBRATED CURRENT SINKS 16 (4-bit) CALIBRATED CURRENT SINKS 1 F OP3 GND TDA1548T GND VSSO VDDO V COM V DDA V SSA MSB470 Fig.30 TDA1548T bitstream/continuous calibration filter-DAC 35 24. AUDIO CONTROL ICs Philips' audio control ICs incorporate stereo pairs of resistive voltage dividers connected to multi-input op-amps, the tail currents of which are either DC controlled via potentiometers, or digitally controlled via the I2C-bus to adjust volume level, stereo balance, bass level, treble level and fader/output selection. The advantages of this principle are very wide dynamic range combined with low noise and distortion. The low noise and low distortion figures have resulted in approval for use with cassette players with Dolby B and C noise reduction. Some of the ICs include a fader control which is independent of the volume control which permits sound distribution adjustment between two pairs of audio power amplifiers. And some include a source selector (e.g. for FM, AM or cassette player inputs). Audio control ICs with I2C-bus control Our sounds fader control ICs comprise five I2C-bus controlled ICs: TEA6320(T)/21/22T/23T/30T. Common features bass and treble control balance control interface for equalizer mute switch via I 2C-bus mute switch via IC pin maximum gain 20 dB THD = 0.05%. Table 40 Comparison stereo audio control circuits with I2C-bus control (measured with an 8.5 V supply) Type number TEA6320(T) TEA6321 TEA6322T TEA6323T TEA6330T 4 (1) 4 (1) 4 (1) 4 (1) 1 (0) interface for noise reduction circuits mute control at audio signal zero crossing loudness with bass and treble setting loudness control combined with volume setting stereo (mono) inputs differential inputs supply voltage V 7.5 to 9.5 7.5 to 9.5 7.5 to 9.5 7.5 to 9.5 7 to 10 max. input (output) signal V 2 (2) 2 (2) 2 (2) 2 (2) 2 (1.1) min. output load resistance k 2 2 2 2 10 stereo volume 1 control: range step resolution dB dB 51 1 51 1 51 1 51 1 86 2 L/R & F/R channel volume control: range step resolution dB dB 55 1 55 1 55 1 55 1 total volume control range dB 106 106 106 106 loudness control: bass boost treble boost dB dB 17 4.5 17 4.5 17 4.5 17 4.5 fader control range dB bass control: range step resolution dB dB 15 1.5 18 1.8 15 1.5 18 1.8 15 3 treble control: range step resolution dB dB 12 1.5 12 1.5 12 1.5 12 1.5 12 3 channel separation dB 96 96 80 80 90 ripple rejection dB 76 76 76 76 70 input isolation dB 105 105 105 105 signal-to-noise ratio dB package 86 30 105 105 105 105 98 SDIL32, SO32 SO32 VSO40 VSO40 SO20 36 MUTE Vref audio left Vref audio right VOLUME BALANCE BASS/ LOUDNESS TREBLE/ LOUDNESS Vref I2C-BUS LOGIC Vref FADER MUTE MSC125 SDA SDA I2C-bus Fig.31 TEA6330T sound fader control circuit left output front rear SOURCE SELECTOR audio left BASS LEFT TEA6320(T) TEA6321 TEA6322T TEA6323T VOLUME 1 LOUDNESS TREBLE LEFT + / - 12 dB (1) MUTE & ZERO CROSS DETECTOR VOLUME 2, LEFT BASS FADER + G = 0...+55 dB G = 20...-31 dB audio right POWER SUPPLY VOLUME 2, RIGHT BASS FADER I 2 C-BUS BASS RIGHT TREBLE RIGHT MGC874 SDA front SCL rear right output (1) Bass gain = +/-15 dB for TEA6320(T)/22T and +/-18 dB for TEA6321/23T (with T-filter network) Fig.32 TEA6320(T)/21/22T/23T sound fader control circuit 37 Audio equalizer circuit with I2C-bus control The TEA6360(T) is a highlyintegrated 5-band stereo equalizer with an I2C-bus controlled tone processor for music centres and car radio. It incorporates 5 stereo pairs of constant-bandwidth boost/ cut bandpass filter sections, each centred on a different audio frequency. It also has a built-in I2C-bus interface for receiving filter setting commands from a microcontroller. Each stereo pair of filters has a linear frequency response setting and can be simultaneously controlled in 5 steps of centre frequency boost or cut. The IC is optimized for a frequency boost/cut of 12 dB in five 2.4 dB steps. The frequency response of the filters can be controlled with constant or variable Q-factor. Each filter section consists of a bridged-T RC network (notch filter) connected in the input or feedback path of an internal operational amplifier. To allow free choice of the centre frequency, maximum gain and Q-factor, the reactive components of each filter section (2 capacitors and one resistor) are external. These can be standard surface-mount types. In the complete equalizer, 5 filter sections are directly connected in series for each stereo channel. Since the overall DC gain of the circuit is 0 dB irrespective of the filter settings, offset voltages are not amplified. Because the entire circuit is DCcoupled, has a wide input signal swing (2.1 V to VS - 1 V) and a typical offset of zero, components for DC decoupling and reference voltages are not necessary. output right GND1 MAD GND2 n.c. 31 input right 29 30 27 26 25 24 23 22 21 20 19 18 17 32 2.95 kHz input left 28 12 kHz 790 Hz 205 Hz TEA6360 59 Hz I 2 C-BUS CONTROL 1 2 4 3 5 6 7 8 9 10 11 12 13 14 15 16 MLA931 n.c. SDA SCL V P output left Fig.33 The TEA6360(T) 5-band stereo equalizer Table 41 TEA6360(T) data (measured with an 8.5 V supply) Characteristic Value supply voltage (VS) supply current 7 to 13.2 V 24.5 mA max. input signal 2.1 V max. output signal 1.1 V frequency response (-1 dB, linear) channel separation 0 to 20 kHz 75 dB total harmonic distortion 0.2 % ripple rejection 60 dB signal-to-noise ratio 93 dB package DIL32 (SOT232)/ SO32 (SOT287) Features 5 filters per channel centre frequency, bandwidth and maximum boost/cut defined by external components variable or constant Q-factor via I2C software I2C control for all functions defeat mode for linear frequency response and optimum noise performance all stages DC coupled 120 dB crosstalk attenuation between I2C-bus inputs and audio outputs 2 different programmable module addresses. 38 Audio control circuits without I2C-bus control Both the TDA1524A and TDA1526 are ICs designed as an active stereo tone/volume control for mains-fed equipment. They include functions for bass and treble control, volume control with built-in contour (can be switched off) and balance. All these functions can be controlled by DC voltages (remote control) or by single linear potentiometers. The TDA1524A is also suitable for car radios with Dolby noise reduction systems. left output VP VOLUME CONTROLLED AMPLIFIER BASS & TREBLE CONTROLLED AMPLIFIER + SUPPLY TDA1524A TDA1526 left input bass treble volume VOLUME CONTROLLED AMPLIFIER BASS & TREBLE CONTROLLED AMPLIFIER + VOLUME / BALANCE CONTROL VOLTAGE CONVERTER TREBLE CONTROL VOLTAGE CONVERTER BASS CONTROL VOLTAGE CONVERTER right input contour linear Common features loudness with bass (and treble) setting bass and treble control balance control mute switch via IC pin. right output volume balance treble bass MGA525 Fig.34 The TDA1524A and TDA1526 stereo audio control circuit Table 42 TDA1524A and TDA1526 data (measured with an 8.5 V supply) Characteristic supply voltage (VS) max. gain max. input signal max. output signal TDA1524A TDA1526 7.5 to 16.5 V 7.5 to 16.5 V 21.5 dB 21.5 dB 2.4 V 2V 2V 2V min. output load resistance 4.7 k 4.7 k stereo volume control range 100 dB 100 dB fader control range 30 dB 30 dB bass control range -19 to +17 dB -15 to +17 dB treble control range 15 dB 15 dB channel separation 60 dB 60 dB total harmonic distortion 0.3 % 0.5 % ripple rejection 50 dB 50 dB signal-to-noise ratio 85 dB 90 dB DIL18 (SOT102) DIL18 (SOT102) package 39 25. DISCRETE SEMICONDUCTORS FOR RADIO/AUDIO Table 43 n-channel JFETs for the RF input stages of AM tuners Type number Yfs (mS) IDSS (mA) -V(P)GS Case min. min. max. min. max. typ. J109 - 40 - 2 6 - J110 - 10 - 0.5 4.0 - BF245A-C 3.0 2 25 0.25 8.0 - BF256A-C 4.5 3 18 0.5 7.5 - BF247A 8 30 80 0.6 14.5 - J309 10 12 30 1.0 4.0 6 J310 10 24 60 2 6.5 6 BF851A-C 12 2 25 0.2 2 1.5 BSR58 - 8 80 0.8 4.0 - PMBFJ110 - 10 - 0.5 4.0 - BF545A-C 3 2 25 0.4 7.8 - BF556A-C 4.5 3 18 0.5 7.5 40 PMBFJ309 10 12 30 1.0 4.0 6 BF861A-C 12 2 25 0.2 2 1.5 TO-92 SOT23 Table 44 MOSFETs for AM/FM tuners Type number Cig1-s (pF) typ. Yfs (mS) typ. V(P)G1-S (V) min. V(P)G2-S (V) min. F (dB) typ. Case BF908(WR) 3.1 43 -2 -1.5 0.6 at 200 MHz 1.5 at 800 MHz SOT143 (SOT342R) BF992 4.0 25 -1.3 -1.1 1.2 at 200 MHz SOT-143 BF998 2.1 24 -2.5 -2.0 1.0 at 800 MHz 0.6 at 200 MHz SOT-143 BF1100(WR) 2.2 28 -1.5 -1.5 2 at 800 MHz SOT143 (SOT343R) 40 Table 45 Varicap diodes for AM tuning Type number VRM (V) Cd (pF) at V(1) (V) Cd (pF) at V(2) (V) Cd ratio at V1/V2 rs () max. f (MHz) C (pF) Matched Case BB112 12 440-540 1.0 17-29 8.5 >18 <1.5 0.5 C1 V <3% SOD-69 BB130 32 450-550 1.0 12-21 28 >23 <2.0 1.0 C1 V <3% SOD-69 BB212 12 500-620 0.5 <22 8.0 >22.5 <2.5 0.5 500 <3.5% TO-92 Table 46 Varicap diodes for FM tuning Type number VRM (V) Cd (pF) at V(1) (V) Cd (pF) at V(2) (V) Cd ratio at V1/V2 rs () max. BB135 30 17.5-21 0.5 1.7-2.1 28 8.9-12 <0.75 470 9 no SOD-323 BB204 30 37-42 3.0 14 30 2.5-2.8 <0.4 100 38 no TO-92 BB804 20 42-47.5 2.0 26 8 1.65-1.75 0.2 100 38 no SOT-23 41 f (MHz) C (pF) Matched Case CUSTOMER SUPPORT During the more than twenty years that Philips has been supplying ICs to meet the needs of radio/ audio manufacturers, we've built an unrivalled reputation for keeping our customers at the forefront of circuit design and innovation. This reputation wasn't earned solely by providing integrated circuits to meet the industry's needs, but also by offering extensive applications and designin support in many countries. An important part of our customer support package is our comprehensive and regularly updated descriptive publications and data handbooks. Another important item is an IICRADIO I2C-bus control program (available on 3.5 inch disk). This program allows engineers to evaluate, analyze and test Philips' radio/audio ICs which have an I2C-bus interface, without knowledge of the internal software structure of the circuits. All that's needed to run the program is an IBM or compatible PC with MS-DOS or PC-DOS and at least 1 Mb of RAM. An I2C-bus interface board must be connected between the I2C-bus of the board under test and the CENTRONICS parallel printer port of the PC. The program incorporates a database for IC control data and a set of easy to use dedicated or universal menus for controlling the ICs. All the menus are selfexplanatory and the desired functions can be accessed with a single keystroke. The dedicated menus show all the control functions of the associated IC divided into logical groups. All data communication on the I2C-bus is subjected to error checking and, if errors occur, they're displayed on the PC screen as simple, easily understood messages. Table 47 Documentation relating to radio/hi-fi ICs Title Ordering code Publication type Audio amplifier ICs designer's guide 9398 706 66011 brochure Audio data converters and misc. digital audio IC's designer's guide 9397 750 00151 brochure Car radio designer's guide 9397 750 00149 brochure CD designer's guide 9397 750 00356 brochure I C-bus control programs for consumer applications 9398 362 90011 brochure Integrated Audio Amplifier... ... from 60 mW to 100 W 9398 706 92011 brochure Philips DCC Key Modules 3122 321 52272 brochure R(B)DS radio PC-card using OM5604 9397 750 00262 brochure Remote control ICs and RC-5 command tables 9398 393 39911 brochure TDA1561Q high-efficiency audio amplifier 9398 707 24011 brochure The I C-bus and how to use it (including specifications) 9398 393 40011 brochure TV designer's guide 9397 750 00148 brochure IC01a - Semiconductors for radio and audio systems 9398 652 61011 data book IC01b - Semiconductors for radio and audio systems 9398 652 62011 data book IC11 - General purpose/linear ICs 9398 182 10011 data book IC12 - I C peripherals 9397 750 00306 data book IC14 - 8048-based 8-bit microcontrollers 9398 177 00011 data book IC20 - 80C51-based 8-bit microcontrollers 9397 750 00013 data book SC07 - Small-signal field-effect transistors 9397 750 00085 data book CPR120S outline specification (version 1.0) AN96020 application note CCA210S outline specification (version 1.0) AN96017 application note ERA/UM96001 user manual AT/RA3490 user manual 2 2 2 CCA210 user manual (version 1.0) CCR910S RDS decoder user manual 42 Title Ordering code Publication type CCR910S RDS decoder outline specification 9398 076 4001 lab. report CCR911S RDS decoder functional specifications HAT/AN92012 lab. report CCR912S RDS decoder user manual HAT/AN92021 user manual CCR921 R(B)DS decoder out line specifications AN95048 application note CCR921 R(B)DS decoder user manual (version 1.0) AN95066 user manual HiFi7000 CD audio system user manual (version 1.0) SAU/UM95018 user manual AN95109 application note Influence of the audio frequency modulation on the RDS data reception HAT/AN92023 application note Quartz crystal oscillator for SAA6579T HAS/AN93001 application note AN95014 user manual SAA6579T RDS demodulator application report HAT/AN92001 application note SAA7740H design engineering software user guide NBA/AN9403 user manual SAA7740H digital audio processor IC for consumer applications NBA/AN9410 lab. report SAA7740H game management user guide NBA/AN9407 user manual AN95108 user manual TDA1548T(Z) low voltage, low power headphone filter DAC (version 1.1) NBA/AN9507 lab. report TDA1551Q/54Q/55Q/58Q audio power amplifiers for car radio NBA/AN9202 lab. report TDA1552Q/53(A)Q, TDA1556Q and TDA1557Q double BTL amplifiers NBA/AN9013 lab. report TDA1560Q power lifting amplifier NBA/AN9206 lab. report TDA2613: economic 6 W hi-fi audio amplifier for mains-fed applications NBA/AN8902 lab. report TDA2614: economic 6.5 W hi-fi audio amplifier for mains-fed applications NBA/AN9110 lab. report TDA2616: 12 W stereo hi-fi audio amplifier NBA/AN9205 lab. report NBA8907 lab. report TDA7052A: 1 W BTL mono audio amplifier NBA/AN9207 lab. report TDA7056: 3 W mono BTL audio amplifier NBA/AN9004 lab. report TDA7056A: 3 W BTL mono audio amplifier with DC volume control NBA/AN9208 lab. report TDA7057: 3 W componentless BTL stereo audio amplifier NBA/AN9009 lab. report HBA9101 lab. report TEA5710: the next step in AM/FM reception NBA/AN9201 lab. report TEA5711/12: AM/FM-stereo ICs for manual & digital tuning NBA/AN9307 lab. report AN95006 lab. report ERA95012.0 lab. report TEA57xx family self tuned single-chip AM/FM receivers AN94082 lab. report TEA6320(T) audio control IC in combination with TEA6360(T) equalizer IC AN95101 lab. report TEA6320T audio control IC measurement results AN95082 lab. report TEA632x family: audio control ICs AN95054 lab. report ZE/21/02/94 lab. report HiFi7000 CD player system outline specification (version 1.2) SAA2500/SAA2501 MPEG Audio Decoders user manual (version 1.0) Smart radio user manual (version 1.0) TDA7052/53: 1 W componentless BTL mono/stereo audio amplifiers TDA7088T: FM one chip receiver TEA5757: FM/MW/LW radio receiver TEA5757H: PC-control TSA6060 fast PLL synthesizer for all radios 43 APPENDIX Alphanumeric index of ICs, modules and systems Type number Description Page ADR Astra digital radio (ADR) system block diagram 12 CCA210 audio system with CD 10 CCR910 radio data system (RDS) decoder 14 CCR911 radio data system (RDS) decoder 14 CCR912 radio data system (RDS) decoder 14 CCR921 radio data system (RDS) decoder 14 CPR120 radio/audio system 8 DAB digital audio broadcasting (DAB) system block diagram 18 OM5604 multimedia radio module 13 OM5606 multimedia radio module 13 OM5608 multimedia radio module 13 P83CL434 8-bit CMOS microcontroller with LCD drive 8, 26 P83CL834 8-bit CMOS microcontroller with LCD driver 8, 26 PC card radio PC card with RDS/RBDS 17 SAA2501H DAB/ADR MPEG audio decoder 18, 30 SAA2502H DAB/ADR MPEG audio decoder 18, 30 SAA2530 ADR/DMX digital receiver 12 SAA6579T radio data system (RDS) demodulator 14 SAA7710T Dolby circuit 32 SAA7740H DSP digital signal processor 32 TDA1016 audio power amplifier 5, 22 TDA1308T audio power amplifier 8, 13, 22 TDA1514A audio power amplifier 9, 22 TDA1517P audio power amplifier 17, 22 TDA1521(Q) audio power amplifier 9, 22 TDA1521A audio power amplifier 9, 22 TDA1524A stereo tone/volume control circuit 9, 39 TDA1526 stereo tone/volume control circuit 39 TDA1546T filter DSP bitstream conversion DAC 32, 34 TDA1548T low power DSP bitstream conversion DAC 32, 34 TDA1560Q audio power amplifier 22 TDA1561Q audio power amplifier 22 TDA2611A audio power amplifier 22 TDA2613 audio power amplifier 22 TDA2614 audio power amplifier 22 TDA2615 audio power amplifier 22 TDA2616 audio power amplifier 22 TDA7021T FM receiver for MTS 2, 7 44 Type number Description Page TDA7050(T) audio power amplifier 22 TDA7052 audio power amplifier 22 TDA7052A audio power amplifier 22 TDA7052AT audio power amplifier 22 TDA7052B audio power amplifier 22 TDA7052BT audio power amplifier 22 TDA7053 audio power amplifier 22 TDA7053A audio power amplifier 22 TDA7053AT audio power amplifier 22 TDA7056 audio power amplifier 22 TDA7056A audio power amplifier 22 TDA7056B audio power amplifier 22 TDA7057AQ audio power amplifier 22 TDA7057Q audio power amplifier 22 TDA7088T FM receiver for battery supply 3 TDA8542(T) audio power amplifier 8, 22 TDA8559(T) audio power amplifier 22 TDA8577 audio power amplifier 22 TDA8578(T) audio power amplifier 22 TDA8579(T) audio power amplifier 22 TEA0657 dual Dolby B noise reduction circuit 25 TEA0665(T) Dolby B & C type noise reduction circuit 25 TEA5551T AM receiver 2 TEA5710(T) AM/FM receiver 4, 5, 19 TEA5711(T) AM/FM receiver 6, 19 TEA5712(T) AM/FM receiver 6, 9, 19 TEA5757H self-tuned AM/FM receiver 8, 10, 13, 21 TEA5759H self-tuned AM/FM receiver 21 TEA5762H self-tuned AM/FM receiver 21 TEA6320(T) sound fader controller 17, 36 TEA6321 sound fader controller 36 TEA6322(T) sound fader controller 36 TEA6323(T) sound fader controller 36 TEA6330T sound fader controller 36 TEA6360(T) 5 band equalizer circuit; I2C-bus TSA6057(T) TSA6060(T) 17, 38 2 radio tuning PLL frequency synthesizer; I C-bus 23 2 radio tuning PLL frequency synthesizer for RDS applications; I C-bus 45 9, 23