MULTILAYER CERAMIC ANTENNA FOR GSM/DCS (900/1800MHz) Product Specification1 (Preliminary) QUICK REFERENCE DATA Frequency Range 880-960 MHz 1710-1880 MHz Bandwidth 30 MHz 170 MHz (Dependant on ground plane size and tuning circuit of customer) Peak Gain 900MHz 0.5~1 dBi 1800MHz 0.5~1 dBi (Dependant on ground plane size and tuning circuit of customer) VSWR 2.7 (Dependant on ground plane size and tuning circuit of customer) Polarization Linear Impedance 50 Operating Temperature -55~125 oC Size 21*12*0.9 mm Special Environmental Concerns- Green Products Design: The foil making process is using environmentally-friendly aqueous solvent technology. Termination is lead free (Pb free) and packing materials can be re-cycled 1 All the technical data and information contained herein are subject to change without prior notice Print date 02/10/16 HF R&D Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 1 sheet 190-1 Oct. 14, 02 A4 PPLICATION 12mm Suggested Layout Ground plane(back side) 2mm Cleanance 6mm Antenna (No ground plane Backside) Bluetooth module or other RF Module Cleanance 6mm 50Ohm Transmission Line (by Microstrip Line or Coplanar Waveguide) DIMENSIONAL DATA Figure Dimension Port W W 20.5 0.25 mm C S T S1 S1 L 11.80.2 mm T 0.900.2 mm F 2.850.35 mm C 1.550.55 mm S 2.850.35mm S1 2.650.65 mm L S1 HF R&D F S1 Print date 02/10/16 Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 2 sheet 190-2 Oct. 14, 02 A4 SOLDER LAND PATTERN Figure S C S S L S F Remark Dimensions L 13 0.10 mm F 1.40 0.10 mm C 0.90 0.10 mm S 1.40 0.10 mm Feed Pad NC Mount Pad S Typical Radiation Pattern Polar Plot (Based on Suggested Layout) 0 45 0 -45 90 45 -90 135 225 90 -90 135 180 225 180 E-Plane H-Plane HF R&D -45 Print date 02/10/16 Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 3 sheet 190-3 Oct. 14, 02 A4 STANDARD TEST BOARD FOR SWR 10.5 cm 14 mm 6 mm (min) 4 cm 1.2 mm SMA Material:FR4 PCB 6 mm (min) 0.8 mm 50 ohm transmission line (Pre-Tuning Reference Only, after-tuning performance is depending on customer installation) HF R&D Print date 02/10/16 Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 4 sheet 190-4 Oct. 14, 02 A4 IEC 384-10/ CECC 32 100 CLAUSE RELIABILITY DATA (Reference to IEC Specification) IEC 60068-2 TEST PROCEDURE REQUIREMENTS TEST METHOD 4.4 Mounting 4.5 4.6.1 Visual inspection and dimension check Antenna 4.8 Adhesion 4.9 Bond strength of plating on end face The antenna can be mounted on printedcircuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive Any applicable method using 10 magnification Frequency = 900M/1800MHz; at 20 oC A force of 3 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate Mounted in accordance with CECC 32 100, paragraph 4.4 Conditions: bending 0.25 mm at a rate of 1mm/s, radius jig. 340 mm, 2mm warp on FR4 board of 90 mm length HF R&D Print date 02/10/16 No visible damage In accordance with specification (chip off 4mm) Standard test board in page 4 No visible damage No visible damage No visible damage Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 5 sheet 190-5 Oct. 14, 02 A4 IEC IEC 384-10/ CECC 32 100 CLAUSE 60068-2 TEST METHOD 4.10 20(Tb) TEST Resistance to soldering heat PROCEDURE REQUIREMENTS 260 5 C for 10 0.5 s The terminations shall be well tinned in a static solder bath after recovery and Central Freq. Change 6% Resistance to leaching 4.11 20(Ta) Solderability 4.12 4(Na) Rapid change of temperature 4.14 3(Ca) Damp heat Using visual enlargement of 10, dissolution of the termination shall not exceed 10% Zero hour test, and test The termination must after storage (20 to 24 be well tinned, at months) in original least 75% is well atmosphere; un-mounted tinned at termination chips completely immersed for 2 0.5 s in 235 5C. No visible damage -55 C (30 minutes) to +125 C (30 minutes); 5 Central Freq. Change 6% cycles 500 12 hours at 60 C; No visible damage 2 hours recovery 90 to 95 % RH Central Freq. Change 260 5 C for 30 1 s in a static solder bath 6% 4.15 Endurance 500 12 hours at 125 C; No visible damage 2 hours recovery Central Freq. Change 6% HF R&D Print date 02/10/16 Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 6 sheet 190-6 Oct. 14, 02 A4 ORDERING INFORMATION: Method I- by 12NC Ordering Code The antennas may be ordered by using the 12 NC ordering code. These code numbers can be determined by the following rules: 4313 1 18 00 918 F C MS T A F. Family Code 43 = Antenna C. Packing Type Code 13 =Bulk (1000 pcs) M. Materials Code 1 = High Frequency Material S. Size Code 18 = 21 *12 * 0.9 mm T. Tolerance 00 = 80 M Hz GSM 900 Band Width 170 M Hz DCS1800 Band Width A. Working Frequency 918 = GSM 900 880-960 MHz DCS 1800 1710-1880 MHz Example: 12NC 4313 118 00918 Product description: Antenna (43) by bulk (13) of High Frequency Material (1), Size 21*12*0.9 mm (18); Tolerance (00) of 80 & 170 MHz (VSWR<2.7) Working Frequency (918) = GSM 900 & DCS1800 ORDERING INFORMATION: Method II- by Clear Text Code The antennas may be ordered by using the 16-digit clear text ordering code. These code numbers can be determined by the following rules: AN0918000721121B (Clear Text Code Example) AN Product AN= Antenna 0918 Central Freq. 900/1800MHz HF R&D 00 Bandwidth GSM/DCS 07 Material 07=K7 2112 Size 2112=21*12m m*0.9mm Print date 02/10/16 1 Quantities 1 = 1K B Packing B = Bulk Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 7 sheet 190-7 Oct. 14, 02 A4 Revision Control: Revision Date Oct. 6, 01 Oct. 14, 2002 HF R&D Content Remark New Issued Modify dimension and termination width (S1, F, C, S2) Print date 02/10/16 Preliminary internal use only Oct. 6, 01 Multilayer Ceramic Antenna for GSM/DCS (900/1800MHz) Grant Lin/Cliff spec.doc Oct. 14, 02 Phycomp Taiwan Ltd. 4313 118 00918 AN0918000721121B Page 8 sheet 190-8 Oct. 14, 02 A4