FTR-K1 SERIES POWER RELAY 2 POLES-2A High insulation/wide gap FTR-C1 Series FEATURES 2 Poles, 2 form C Contact gap: more than 0.6mm High surge voltage: 2,500V between open contacts 5,000V between coil & contact Complies with Telcordia (former Bellcore) 2nd level surge Dielectric strength: 1,500VAC between open contacts 3,000VAC between coil and contact Dimensions of large contact gap relay Height: 9.4mm maximum (THT) 9.7mm maximum (SMT) Length: 15.2mm maximum Width: 7.7mm maximum Conforms to IEC60950/ EN60950/UL1950/CSA C 22.2 No. 950 working voltage 250V (supplementary) High insulation: Clearance: min 2.0mm (coil and contacts) Creepage: min 2.5mm (coil and contacts) Low power consumption 280mW (latching type 140mW) RoHS compliant. Please see page 9 for more information Plastic sealed PARTNUMBER INFORMATION [Example] (a) FTR-C1 (a) Relay type (b) C (b) A (c) 012 (d) G - B05 (e) (f ) FTR-C1 : FTR-C1-Series C G S : Through hole type : Surface mount type : Surface mount type reduced mounting area (c) Coil type / enclosure A B : Standard type : Single coil latching type (d) Coil rated voltage 012 : 3.....24 VDC Coil rating table at page 3 (e) Contact material G : Gold plated silver palladium (stationary contact) Silver palladium (movable contact) (f) Tape / reel version Nil B05 : Tube packing : Tape / reel packing, only available for SMT type Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-C1CA012G Actual marking: C1CA012G 1 FTR-K1 SERIES FTR-C1 SERIES SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation Non-latching FTR-C1 ( ) A Configuration 2 form C Construction Bifurcated Material Gold plated silver palladium (stationary contact) Silver palladium (movable contact) Resistance (Initial) Max. 150m at 1A, 6VDC Contact rating resistive 1A, 30VDC / 0.3A, 125VAC Max. Switching Voltage 250VAC / 220VDC Max. Switching Power 62.5VA / 30W Max. Carry Current 2A Min. Switching Load * 0.01mA, 10mVDC Mechanical Min. 10 x 106 operations Electrical (resistive) Min. 100 x 103 operations at 0.3A, 125VAC / 1A, 30VD Rated Power 280 to 300mW 140 to 180mW Operate Power 158 to 162mW 158 to 162mW Pulse width - Min. 20ms Operating temp range -40C to +85C (no frost) Storage temperature / humidity -40C to +85C / 5% to 85% RH (no frost) Operate (at nominal voltage) Max. 6ms (without bounce) Release (at nominal voltage) Max. 6ms (without bounce) Resistance (Initial) Min. 1,000M at 500VDC Dielectric strength Surge strength Clearance Creepage Other Latching FTR-C1 ( ) B Vibration Resistance Shock Open contacts 1,500VAC (50/60Hz) 1min Adjacent contacts 1,500VAC (50/60Hz) 1min Contacts to coil 3,000VAC (50/60Hz) 1min Contacts to coil 5,000V, 2 x 10s Open contacts 0.6mm Adjacent contacts 1.0mm Contacts to coil 2.0mm Open contacts 0.6mm Adjacent contacts 1.0mm Contacts to coil 2.5mm Misoperation>1us 10 to 55 to 10 Hz single amplitude 1.65mm Endurance 10 to 55 to 10 Hz single amplitude 2.5mm Misoperation>1us Min. 500m/s2 (11+/-1ms) Endurance Min. 1,000m/s2 (6+/-1ms) Weight Approximately 2g Sealing RT III (plastic sealed) * Minimujm switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-C1 SERIES COIL RATING n Standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 003 3 32.1 2.25 0.3 4.5 4.5 72.3 3.38 0.45 005 5 89.3 3.75 0.5 012 12 514 9 1.2 024 24 1,920 18 2.4 300 Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Set Voltage (VDC) * Reset Voltage (VDC) * Nominal Coil Power (mW) 003 3 64.0 +2.25 - 2.25 4.5 4.5 145 +3.38 - 3.38 005 5 179 +3.75 - 3.75 012 12 1,029 +9 -9 024 24 3,200 +18 - 18 Nominal Coil Power (mW) 280 Latching type 140 180 Note: All values in the table are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. Note: Please use at rated coil voltage. Please perform the confirmation test with actual conditions. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E63615 CSA C22.2 No. 14 LR 40304 0.3A, 125 VAC (general use) (UL) 0.5A, 125VAC (CSA) 2A, 30VDC (general use) 0.3A, 110VDC (general use) Comply with Telcordia specifications and meet BSI Marking only for UL, CSA 3 FTR-K1 SERIES FTR-C1 SERIES n CHARACTERISTIC DATA Operating range Operating range 2.4 Non-latching type 2.2 0A 2.0 1.8 2A 1.6 1.4 1.2 (hot oltage erate v 1.0 p Must o 0.8 erate Must op 0.6 0 voltage coil) ) (cool coil 20 40 60 80 100 Ambient temperature () Nominal voltage multiplying factor Nominal voltage multiplying factor 2.4 Latching type 0A 2.2 2.0 1.8 2A 1.6 1.4 1.2 coil) ge (hot te volta ra e p o il) t Mus (cool co voltage te ra e p Must o 1.0 0.8 0.6 0 20 40 60 80 100 Ambient temperature () 4 FTR-K1 SERIES FTR-C1 SERIES 5 FTR-K1 SERIES FTR-C1 SERIES DIMENSIONS Through hole type Schematics (BOTTOM VIEW) Dimensions 7.7 max. 7.4 typ. +(-) 1 3 12 10 4 5 3.5 5.08 9.4 max. 9.1 typ. 15.2 max. 14.9 typ. Recommended PCB layout (BOTTOM VIEW) 0.5 5.08 2.54 2.54 8 5.08 Orientation mark 0.2 Surface mount type Schematics (TOP VIEW) Dimensions Recommended PCB layout (TOP VIEW) 1 7.7 max. 7.4 typ. 1 1 12 5.08 2.54 2.54 1 +(-) 5.08 3 5 4 3.16 0.5 3 0.2 1.5 9.7 max. 9.4 typ. -(+) 1 7.24 15.2 max. 14.9 typ. 2.54 2.54 3.16 5.08 -(+) 5.08 Orientation mark Surface mount (space saving) type Schematics (TOP VIEW) Dimensions 7.7 max. 7.4 typ. -(+) 12 Recommended PCB layout (TOP VIEW) 10 9 8 3 4 5 1 1 1 1 (1.1) 5.08 2.54 2.54 1 +(-) 3 0.5 5.08 7.4 2.16 0.2 1.5 6.24 9.7 max. 9.4 typ. 2.16 15.2 max. 14.9 typ. 2.54 2.54 5.08 2.54 2.54 Orientation mark Note: (...) : dimensions are reference Note: Dimensions of the terminals do not include thickness of pre-solder. Note: Dimensions do not include tolerances. Please ask specification in case you need tolerances. Note: Tolerance of PCB layout: 0.1 unless otherwise specified. Unit: mm 6 FTR-K1 SERIES FTR-C1 SERIES n RECOMMENDED SOLDERING CONDITIONS SMT (TEMPERATURE PROFILE, please see page 9) Note: 1.Temperature profiles show the temperature of PC board surface. 2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board surfaces vary according to the size of PC board, status of parts mounting and heating method. n TAPE & REEL PACKAGING SPECIFICATION 1. Taping standards: JIS C 0806 and RC-10092B (EIAJ) 2. Tape type: TB2416 or TE2416 3. Reel type: RD24D 4. Quantity of 1 reel: 500 pieces Tape Dimensions: Reel Dimensions: Unit: mm 7 FTR-K1 SERIES FTR-C1 SERIES RoHS Compliance and Lead Free Information 1. General Information All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. l All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l Characteristic data is not guaranteed values but measured values of samples from production line. l 2. Recommended Lead Free Solder Condition l Recommended solder Sn-3.0Ag-0.5Cu. Reflow Solder condition for SMT Flow Solder Condition: Pre-heating: maximum 120C within 90 sec. Soldering: dip within 5 sec. at 255C 5C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron 30-60W Temperature: maximum 340-360C Duration: maximum 3 sec. REFLOW Note: 1.Temperature profiles show the temperature of PC board surface. 2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board surfaces can vary, depending on the size of PC board, status of partsmounting and heating method. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity SMT versions of FTR-C1 relays in Tape & Reel package will be shipped in Moisture Barrier Bag(MBB). Moisture Sensitivity Level (MSL) of FTR-C1 relay is indicated on the packing caution label. l Relays must be stored in the unopened MBB at storage conditions <40C/90%RH for a maximum 1 year l SMT versions of FTR-C1 relays in tube packing will not be shipped in MBB. Therefore, these relays shall be dried by baking before reflow soldering process according to IPC/JEDEC J-STD-033. l l 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 8 FTR-K1 SERIES FTR-C1 SERIES Cautions * * * All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation test before actual use. Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may increase. Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure. Notes for latching relay * * * Latching relays are shipped in the state set, but state may change due to shock during transportation or mounting. Before using the relays, it is advisable to bring the relays in necessary state (set or reset) and program a circuit sequence. Otherwise, it will or will not operate simultaneously with power activation. Please connect relay coils according to specified polarity. Do not apply voltage to both set coil and reset coil at a time. 9 FTR-K1 SERIES FTR-C1 SERIES Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcsh@cn.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ (c)2019 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. October 11th, 2019 10