LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules LPM409 (Industrial) Industrial equipment Telecommunications Test and measurement Automation Peripherals Audio/broadcast Linear and rotary motion LMM409 (Medical) Imaging Equipment Anesthesiology Surgical Devices Diagnostic Equipment Patient Beds Home Healthcare Ultrasound FEATURES Rear Module Connection Area * * * * * * * Supply Front View Fig.1 LPM409 Expanded Views * * * * * Standard output voltages of 1.5 to 54 VDC Efficiencies up to 87% typical Extra-Low 1U profile: 1.6 inch High power density design of 14 Watts/cubic inch 1 to 4 isolated outputs with full user configurability Power Factor Correction (PFC) IEC 61000-3-2 compliant 700W @ 85 VAC or 900W @ 150VAC of total output power Zero-load operation Single-wire current sharing Universal input AC range Individual control signals on each module Auxiliary power 5V (1A) 1. Description The LPM/LMM409 Series is a modular 900-watt AC-DC power supply that provides a market-leading power density of 14 watts per cubic inch and has an extra low 1U profile. LMM is medically approved version. Further will be discussed only LPM version and differences of LMM will be noted. The LPM409 offers the flexibility of a modular architecture and the combination of high efficiency and high power density. Designed for use where a unique set of voltage and current requirements are needed, the supply's four slots can be configured with PCB-based output modules to deliver up to four outputs. The LPM output modules operate in any chassis position and can provide up to 900 watts total power from a 150 VAC input and 700 watts from a 85 VAC input. Forced-air cooling with airflow direction from front to back is provided by an internal fan. For LPM409 supplies using less than the four-slot capability, blanking plates are installed for safety purposes and to optimize airflow within the chassis. The supplies are pre-set with default output module settings or with the customer's desired output settings prior to delivery. The LPM409 chassis can be populated with the output modules listed in Table 1. BCD.00365 Rev. AA, 21-May-14 Page 1 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Table 1. Module Selection 1.1 MODULE P/N NO. OF SLOTS REQUIRED FACTORYSET SINGLEOUTPUT (VDC) MODULE ADJUSTABLE RANGE (VDC) MAX. OUTPUT CURRENT (AMPS) MAX. OUTPUT 2 POWER (WATTS) E LPM126-OUTA1-05 1 5 2.0 to 5.3 53 265 F LPM126-OUTA1-12 1 12 5.2 to 15 22 265 G LPM126-OUTA1-24 1 24 14 to 30 11 265 H LPM126-OUTA1-36 1 36 29 to 44 7.4 265 J LPM126-OUTA1-48 1 48 43 to 54 5,5 265 K LPM109-OUTA1-10 1 15 1.5 to 15 6 90 L LPM109-OUTA1-20 1 30 3 to 32 3 90 M LPM118-OUTA2-10 1 15 2x 1.5 to 15 2x 6 2x 90 N LPM118-OUTA2-20 1 30 2x 3 to 32 2x 3 2x 90 0 LPM000-BLAN 1 Blank Panel (Slot Cover) 1 To determine your desired power supply's part number, please refer to Fig.3 for a detailed part number description. Use the LPM Configurator located in the Modular Section on our website, or use our contacts page to locate a distributor for further assistance. (http://lpm.power-one.com/cgi-bin/start.cgi/lpm/config_start.html) 2 For the power derating specification please see section 1.4 below. Output Voltage Adjustment Each LPM409 module's output voltage is adjustable by means of a trimmer located on the module. For the modules E<->J the trimmer is accessible through the adjustment hole located on the bottom of the power supply (see Fig.11). For the modules K<->N the trimmer is accessible from rear side of the power supply (see Fig.6). 1.2 Parallel Connections Depending on certain situations where current requirements exceed one module's capability, the configurator will process a solution using parallel connections. Paralleling busbars are available to make the connections requiring higher current needs. To ensure the current sharing function works correctly it is required to interconnect the signal pins of the modules that will operate in parallel. Only E-J modules can be connected in parallel. For more details read section 10.3 and Fig.17. 1.3 Serial Connections To increase the output voltage it is possible to connect modules in series. Serial busbars are available (see section 10.4) to make the connections requiring higher voltage needs. The output of LPM409 is rated as SELV circuit, so the output voltages are guaranteed to be less than 60V. The series combination of modules can exceed this SELV voltage, so in this case the users must take adequate precautions. The maximal total voltage must not exceed 200V. Power One recommends to only connect the same modules with the same current rating in series. The voltage sense pins VS+, VS- available on LM126 modules must be connected according to Fig.18. BCD.00365 Rev. AA, 21-May-14 Page 2 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 1.4 Power derating When specifying an LPM409 power supply in an application it is necessary to ensure that LPM409-CHAS and modules (LPM126, LPM118 and LPM109) are operating within their power output capabilities, taking into account the temperature derating and input voltage derating. The maximum permissible output power that may be drawn from LPM409-CHAS and modules assembled in this chassis is given in the Fig.2. a.) b.) c.) d.) Fig.2 Power derating curves a.) for LPM409-CHAS, b.) for module LPM126-5V c.) for modules LPM126-12/24/36/48V and d.) for modules LPM118 / LPM109 BCD.00365 Rev. AA, 21-May-14 Page 3 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 2. Part Numbering and Ordering Information Chassis Identification Numbering 2.1 First left-to-right sequence of the part number (4 characters): * LPM409 .. Low Profile Modular 4-slot, 900W, with single-phase AC input. (see Fig.3) Note: Chassis and modules are RoHS-6 compliant. Fig.3 LPM 4-Slot model part number description Example: After entering your requirements, the web Configurator could recommend the following optimized part number: LPM409-0HEG-DXXX which represents: Low Profile Modular Series with single-phase AC input, 4-slot, 900W chassis with modules of: blank panel "0" and modules H, E, G in slots 1 to 4, respectively. Besides the blanking panel in slots 1, the example's modules in this case would represent desired DC output voltages as follows: Slot 2 = H for 36V, Slot 3 = E for 3.3V and Slot 4 = G for 24V. Assembly facility code and customer build ID No. are established during actual power supply assembly. The slots numbering 1-4 is from the left to right when looking from the rear. 3. Safety specifications 3.1 * * * * 3.2 Safety approvals nd UL/CSA 60950-1, 2 nd IEC 60950-1, 2 nd EN 60950-1, 2 CE Mark for LVD LMM medical rd UL/CSA 60601-1, 3 rd IEC 60601-1, 3 rd EN 60601-1, 3 Insulation Safety Ratings TEST POINTS MINIMUM TEST VOLTAGE INSULATION SAFETY RATING Input-to-Chassis 2120 Vdc / min. 1s Basic Insulation Input-to-Output 4240 Vdc / min. 1s Reinforced Insulation Outputs-to-Chassis 200 Vdc / min. 1s Functional Insulation Output-to-Output 200 Vdc / min. 1s Functional Insulation BCD.00365 Rev. AA, 21-May-14 Page 4 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 4. Environmental and Reliability specifications 4.1 Environmental specification PARAMETER CONDITIONS / DESCRIPTION Cooling Internal DC fan, air intake is from the AC connector side exiting at the DC module side Audible Noise Single unit, 4 modules assembled and full loaded, on a table at 1m distance. Operating Temperature 50C at Full power and up to 70C at 50% load (linearly derated, for details see section 1.4) MIN. -20 Storage Temperature 25 -40 Humidity 95% relative humidity @ 25 C, non-condensing Vibration Operating: Swept 5-500-5Hz profile, 3 axis, 5 sweep cycles per axis Non-operating: Swept 5-500-5Hz profile, 3 axis, 5 sweep cycles per axis Operating: 11ms, half sine, 10 shocks per face Non-operating: 11ms, half sine, 3 shocks per face Shock 4.2 NOM. MAX. UNITS 65 dBA 50 C 75 C 1 Gpk 4 Gpk 20 Gpk 40 Gpk Reliability PARAMETER Calculated MTBF Demonstrated MTBF CONDITIONS / DESCRIPTION According to MIL-HDBK217, Ground benign 30 C, Note: Calculation was done for LPM409-EFGH. Tamb=25C MIN. NOM. UNIT S MAX. 250,000 hours 250,000 hours 5. Fault Protection PARAMETER CONDITIONS / DESCRIPTION Input Fuse One fuse, non-user serviceable, located on line leg of AC input, Fast Acting type Inrush Current Limitation Provided by NTC Short Circuit Protection Provided by Current Limit circuit Output Overvoltage Protection Latching (unit needs to be turned-off and on) Over Temperature OT with auto restart 1 MIN. NOM. MAX. UNITS 12,5 A See Input specification section 105 10 1 125 1 % Io_nom 25 % Vo_nom 70 C amb 100-150% for K, M modules 100-200% for L, N modules BCD.00365 Rev. AA, 21-May-14 Page 5 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 6. EMC specifications 6.1 EMC Immunity PARAMETER CONDITIONS / DESCRIPTION CRITERION Electrostatic Discharge (ESD) IEC/EN61000-4-2; GR-1089 R2-1, R2-2, R2-3 Level 4: contact: 8 kV, air: 15kV Perform, criterion B RF Susceptibility IEC/EN 61000-4-3; Level 3: 10 V/m; 80 MHz to 1000 MHz; AM 80%, 1 kHz radiated; RF electromagnetic field Perform, criterion A Fast transient / burst IEC/EN 61000-4-4; Level 3; 2 kV, 5kHz electrical fast transient / burst immunity test Perform, criterion B Surge IEC61000-4-5, level 3; line to earth: 2kV, line to line: 1kV surge immunity test Perform, criterion B RF conducted disturbance IEC/EN 61000-4-6; Level 3; GR-108; 10V, 0.15 to 80MHz, AM 80%, 1kHz Perform, criterion A IEC/EN 61000-4-11; Voltage dips, interruptions and variations. (Interpretation: dip below Vi min with Po nom = hold-up time 10 ms) Voltage dips / short interruptions 6.2 1a: Dip 30%, 100ms Perform, criterion B 1a: Dip 30%, 200ms Perform, criterion B 1a: Dip 60%, 10ms Perform, criterion A 1a: Dip 60%, 100ms Perform, criterion B 1a: Dip >95%, 10ms (interruption) Perform, criterion A 1a: Dip >95%, 100ms (interruption) Perform, criterion B EMC Emission PARAMETER CONDITIONS / DESCRIPTION CRITERION Conducted Emission EN55022, FCC EN 55022, FCC - EN 55022, and CISPR 22 Class B, FCC 47CFR15 unintentional radiators; standalone at all nominal input voltages and measured in Po1: 0, 50%, 100%; signal connections open Class B; min. 3dB/V margin Radiated Emission EN55022, FCC EN 55022, FCC - EN 55022, and CISPR 22 Class B, FCC 47CFR15 unintentional radiators; standalone at all nominal input voltages and measured in Po1: 0, 50%, 100%; signal connections open Radiated Class A QSP / AVG min. 3 dB margin Input Current Harmonics EN 61000-3-2, sine wave input, Class D; measured standalone at all Vin nominal at power levels between 0 and rated Pass BCD.00365 Rev. AA, 21-May-14 Page 6 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 7. Electrical specifications 7.1 Input Specifications PARAMETER CONDITIONS / DESCRIPTION Input AC Voltage Range Continuous AC voltage Range Po=700W from 85-150 VAC Po=900W from 150-264 VAC Input Overvoltage Range At max. power, no input OVP shutdown MIN. NOM. MAX. UNITS 85 115/230 264 VAC 300 VAC 1 Ohm Ground continuity 0.1 Leakage Current @ 264 VAC, 60Hz, Commercial LPM / Medical LMM Frequency AC line Power Factor Active PFC meets requirements of EN 61000-3-2 at full load ,120/230 VAC input Input Current Steady state, 85 VAC at 700W 230 VAC, Max Power, 25C, acc. prETS300-132-1 (Repeat rate >1min) 2 63 Hz 11 Arms 40 A pk Vi = 230 VAC 100% loading 86 87 % Vi = 230 VAC 30-80% loading 80 82 % Vi = 115 VAC 100% loading 83 84 % Vi = 115 VAC 30-80% loading 78 80 % 1 For any combination of output modules, any valid load and voltage setting 2 Efficiency typical for standard configuration EFGH and nominal output voltage settings 7.2 50/60 mA 0.98 180 VAC, Max Power, 25C, acc. prETS300-132-1 Inrush Current Efficiency 47 1.5 / 0.5 Output Specifications PARAMETER CONDITIONS/DESCRIPTION Output Power One fan for internal cooling Output DC All output modules work in any chassis position and are max 1U high PCB-based Voltages / Modules Current Share 3 MIN. NOM. MAX. 900 UNITS W - Active single-wire current share (modules E-J) Max. difference in currents between two modules- percentage of one module nominal current 10 % Line Regulation Input from 85 to 264 VAC , 80% load 1.0 % Vo_nom Load Regulation From 0-100% load, Input >180VAC, Vo_nom 1.0 % Vo_nom Thermal Drift After 15 minute warm-up period 0.02 %/C BCD.00365 Rev. AA, 21-May-14 Page 7 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Total Regulation Variation of line, load and temperature drift 2.0 % Vo_nom See Module Selection Table 1 Output Adjust. Range Deviation for 10-90% or 90-10% load changes at a rate of 1A/s, (constant current mode, Vo reach 1% band around Voset) 4% 2000s Deviation for 50-100% or 100-50% load steps with 1A/s rate. (constant current mode, Vo reach 1% band around Voset) 3% 400s - 1% of 1 Vo_nom mVpk-pk 500 mVpp 1,2 - Dynamic Response 1 Output Ripple & Noise BW = 20MHz; Filter 10nF/10uF; over line and load, 25C CM Noise Output to chassis, over line and load (Measured across 50 Ohms, with 10H / 10nF in parallel) Overshoot Output voltage overshoot at turn-on Turn-On Characteristics Turn ON at minimum and nominal output current Monotonic characteristic - Turn-Off Characteristics Turn OFF at minimum and nominal output current Monotonic characteristic - Time required for output within regulation after initial application of AC input 1.5 s Time required for output within regulation after removing inhibit 100 ms 220 4 % Vo_nom Turn-On Time Vo is required to stay within 95% regulation after AC is removed. Measured from the last AC peak, VAC min and full load. Hold-up Time Remote Sense 3 Over-current Protect. 1 2 3 10 Total compensation for cable losses Automatic recovery / Hiccup by K-N modules ms 250 500 mV 130 / 180 % the E module dynamic deviation is less than 6%, the E, K, M module ripple is less than 2% the K and M module dynamic deviation is less than 7% and response time is below 1000us except K-N modules BCD.00365 Rev. AA, 21-May-14 Page 8 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 7.3 Input - Signals, Features and Indicators description 10V, 20V Dual-Output Modules Signal Name Pin Description Auxiliary Output 1,2 vs 3,4 (RTN_D) Output is available when the AC input is over 85VAC. The output nominal output voltage is 5.0V at maximum current rating of 1.0A. Over current protection occurs above 1.5A. The output is referenced to logic return, RTN_D. 5 Open Collector output with 20mA pull-down capability referenced to logic return RTN_D. PFAIL open or High state indicates the warning that the input is out of limits (the input voltage falls below 85Vac or rises over 264Vac ) 5 ms before the output goes below the lower regulation limit. PFAIL will turn-off the green Input OK LED. PFAIL LOW state indicates that the input voltage is within the operating range. 6 Open Collector output pin with 20mA pull-down capability referenced to logic return RTN_D. FAN_FAIL OPEN OR HIGH state indicates a fan failure/over temperature protection (OTP) condition min. 100 ms before the unit shuts-down. A fan failure/OTP condition will turn-off the green FAN OK LED. FAN_FAIL LOW state indicates normal fan operation and no OTP condition. - 5V - Input AC Low Indication - PFAIL - Fan Fail / OTP Indication - FAN_FAIL - 7.4 Output - Signals, Features and Indicators description Modules E, F, G, H, J Signal Name Pin Positive sense wire 1 Output voltage sense wire. Internally connected to Vout+ via 51 connect sense wire at positive load point. . It is recommended to 2 Output voltage sense wire. Internally connected to Vout- via 51 sense wire at negative load point. . It is recommended to connect 3 Common wire for parallel connected modules to achieve proper current sharing between the modules. Referenced to the Common pin. Interconnect CS pin on all parallel working modules. Active current share pin enables control of output voltage. Pulling-up this pin to 5V is possible to increase the output voltage. Pull-down of this pin has no effect. Voltage on this pin is 3.5V at nominal module current. Common 4 Reference pin to CSH N/C 5 N/C 6 - VS+ Negative sense wire - VS- - Current share - CSH - Output Good indication 7 Open collector output with 20mA pull-down capability, max. 15V (recommended Rpull-up=1k, Vcc=5V). Referenced to PG_LO. PG_HI OPEN OR HIGH state indicates that the module output voltage is below lower regulation limit. A PG_HI fail state turns the GREEN DC OK LED to RED. PG_HI LOW state indicates the module output voltage is within normal operation limits. 8 Reference pin to PG_HI - PG_HI - PG_LO Output Inhibit function 9 - INH_HI - INH_LO - Description 10 An opto-isolated input with 2-10mA current capability. Apply +(3-15)V on INH_HI and RTN on INH_LO (e.g. from the Auxiliary Output 5V) to activate the inhibit function. INH_HI OPEN OR LOW state ENABLES the module output. INH_HI HIGH state INHIBITES the module output. Reference pin to INH_HI BCD.00365 Rev. AA, 21-May-14 Page 9 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Output - Signals, Features and Indicators description Modules K, L, M, N Signal Name Pin - INH_LO_B - 1 Output Inhibit function 2 - INH_HI_B - PG_LO_B - Output Good indication 4 N/C 6 - INH_LO_A - 7 8 - INH_HI_A - Reference pin to INH_HI_A An opto-isolated input with 2-10mA current capability. Apply +(3-15)V on INH_HI_A and RTN on INH_LO_A (e.g. from the Auxiliary Output 5V) to activate the inhibit function. INH_HI OPEN OR LOW state ENABLES the module output. INH_HI HIGH state INHIBIT the module output. 9 Reference pin to PG_HI_A 10 Open collector output with 20mA pull-down capability, max. 15V (recommended Rpullup=1k, Vcc=5V). Referenced to PG_LO_A. PG_HI OPEN OR HIGH state indicates that the module output voltage is below lower regulation limit. A PG_HI fail state turns the GREEN DC OK LED to RED. PG_HI LOW state indicates that the module output voltage is within normal operation limits. - PG_HI_A - 7.5 INH_HI OPEN OR LOW state ENABLES the module output. INH_HI HIGH state INHIBIT the module output. Open collector output with 20mA pull-down capability, max. 15V (recommended Rpullup=1k, Vcc=5V). Referenced to PG_LO_B. PG_HI OPEN OR HIGH state indicates that the module output voltage is below lower regulation limit. A PG_HI fail state turns the GREEN DC OK LED to RED. PG_HI LOW state indicates that the module output voltage is within normal operation limits. 5 Output Good indication An opto-isolated input with 2-10mA current capability. Apply +(3-15)V on INH_HI_B and RTN on INH_LO_B (e.g. from the Auxiliary Output 5V) to activate the inhibit function. Reference pin to PG_HI_B N/C - PG_LO_A - Reference pin to INH_HI_B 3 - PG_HI_B - Output Inhibit function Description Visual Alarms description Alarm Name LED position Description Input AC Good Front panel - LED2 (see Fig.7) ON state LED indicates operation within specified input voltage range. GREEN LED indicator goes to an OFF condition on PFAIL signal failure state. Fan Good Front panel - LED1 (see Fig.7) ON state LED indicates normal fan operation and no OTP status. GREEN LED indicator goes to an OFF condition on FAN_FAIL / OTP signal failure state. Output Good Module connector / rear side (see Fig.5 and Fig.6) GREEN LED indicates that module output voltage is over minimum regulation limit. GREEN LED indicator goes to RED on PG_HI signal failure state. BCD.00365 Rev. AA, 21-May-14 Page 10 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Connector Details 8. 8.1 Input Connector Information LPM409 front panel connectors pinout refers to Fig.4 and chapter 8.2 and 8.3. The signal connector is Cvilux part number: CI3306P1H10, the mating part is Cvilux CI3306S0010, Molex 50-57-9406 or Taiwan King Pin P553L06(LF). Note: See chapter 10.1 Mating Connections and cables for Input cable information. Fig.4 LPM409 Front Panel Connectors Pinout View 8.2 Input Power Connector - Pinout Signal Name Pin # Type Earth V max I max Recommended wires Earth / Chassis AC Neutral N Input Power AC AC Line L Input Power AC Fused 2 Min. 0,75 mm e.g. Interpower 86230120 Max. torque on screws (M4x6): 1,5 Nm 264 Vrms 10 Arms Caution: The plastic cover must be in place when AC input voltage is applied to the unit! The cover may be removed (with the help of a screwdriver) only when the input cable is disconnected from the mains. 8.3 Input Signal Connector - Pinout (Mating connector: Molex 50-57-9406, pins: Molex 16-02-0082) Signal Name Pin # Wire Color Type Signal reference Low level High level +5V 1 Red Aux Output RTN_D - +5V 2 Red Aux Output RTN_D - RTN_D 3 Black Logic Reference Potential - - - RTN_D 4 Black Logic Reference Potential - - - PFAIL 5 Yellow Open Collector Output + ZD 5.6V RTN_D FAN_FAIL 6 Green Open Collector Output + ZD 5.6V RTN_D BCD.00365 Rev. AA, 21-May-14 Page 11 of 20 <400mV@ 20mA Pull up <400mV@ 20mA Pull up V max I max 5.0Vdc 1.0Adc 20mA 20mA www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 8.4 Module Outputs Pinout Modules E, F, G, H, J - A, B Bus-Bar Signal Name Pin # Type Signal reference Low level High level Vout+ Vout+ Output Power DC Vout- - Vout- Vout- Output Power DC - - V max I max See Module Selection Table 1 See Module Selection Table 1 Connector type: Bus-bar see Fig.5 Mating part: Ring terminal for M4 screw, with appropriate cross section for wire. Modules K, L, M, N 1 Signal Name Pin # Type Signal reference Low level High level Vout1+ Vout1+ Output 1 Power DC Vout1- - Vout1- Vout1- Output 1 Power DC - - Vou2+ 1 Vout2+ Output 2 Power DC Vout2- - Vout2- 1 Vout2- Output 2 Power DC - - V max I max See Module Selection Table 1 See Module Selection Table 1 See Module Selection Table 1 See Module Selection Table 1 valid only for two outputs modules M and N. Connector type: Phoenix Contact 1803277 Mating part: Phoenix Contact 1850660 Fig.5 Modules E,F,G,H,J Power Output Connectors BCD.00365 Rev. AA, 21-May-14 Fig.6 Modules K,L,M,N Power Output Connectors Page 12 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 8.5 Module Output C Signal Connector Pinout The output signal connector provides signal information across its 10-pin output, for position of the output signal connector please see Fig.5 and Fig.6. Connector type: JST S10B-PHDSS-B Mating part: JST housing PHDR-10VS, pins SPHD-002T-P0.5 (AWG 28-24) or SPHD-001T-P0.5 (AWG 26-22) Modules E, F, G, H, J - signal output connector pinout Signal Name Pin # Type Signal reference Low level High level V max I max VS+ 1 Output voltage sense wire. Internally connected to Vout+ via 51 Vout+ - 0.5V 10mA VS- 2 Output voltage sense wire. Internally connected to Vout- via 51 Vout- - 0.5V 10mA CSH 3 Active Current Share pin Common - 5V - Common 4 Reference pin to CSH - - - N/C 5 - - - - N/C 6 - - - - PG_HI 7 Open collector output PG_LO <400mV@5mA Pull up 15V 20mA PG_LO 8 Reference for PG_HI - - 20mA INH_HI 9 Input, protected by 18V Zener diode INH_LO LED with a serial resistor 2 kOhms 15V 10mA INH_LO 10 Reference for INH_HI - - 10mA BCD.00365 Rev. AA, 21-May-14 Page 13 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Modules K, L, M, N- signal output connector pinout Signal Name Pin # Type Signal reference Low level High level V max I max INH_LO_B 1 Reference for INH_HI_B - - 10mA INH_HI_B 2 Input, protected by 18V Zener diode INH_LO_B LED with a serial resistor 2 kOhms 15V 10mA PG_LO_B 3 Reference for PG_HI_B - - 20mA PG_HI_B 4 Open collector output PG_LO_B <400mV@5mA Pull up 15V 20mA N/C 5 - - - - N/C 6 - - - - INH_LO_A 7 Reference for INH_HI_A - - 10mA INH_HI_A 8 Input, protected by 18V Zener diode INH_LO_A LED with a serial resistor 2 kOhms 15V 10mA PG_LO_A 9 Reference for PG_HI_A - - 20mA PG_HI_A 10 Open collector output PG_LO_A <400mV@5mA Pull up 15V 20mA BCD.00365 Rev. AA, 21-May-14 Page 14 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 9. Mechanical Drawings * * Overall Dimensions: 11.9" x 3.6" x 1.6" (303.7 x 92 x 40.64mm) Weight: 1.38 kg (including 4 modules) All drawing dimensions are shown in millimeters, unless otherwise notated. Fig.7 Front View Fig.8 Rear View BCD.00365 Rev. AA, 21-May-14 Page 15 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Fig.9 Side View Fig.10 Top View Fig.11 Bottom View BCD.00365 Rev. AA, 21-May-14 Page 16 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 10. Accessories 10.1 Mating Connections and Cables All the power and signal cables and mating connectors are not included in the LPM409 standard package. These all need to be ordered extra. * * * * Front panel signal cable: Output signal cable: mating connector: Output power cable (for LPM126): Power-One accessory LPM000-LEAD-03, see Fig.12 Power-One accessory LPM000-LEAD-04, see Fig.13a JST, housing PHDR-10VS, pins SPHD-002T-P0.5 (AWG 28-24) 14AWG - 10AWG depend on the output current, min. thermal 2 class 105C, lug terminal 4mm 6mm Output power cable (for LPM109/118): Power-One accessory LPM000-LEAD-05, see Fig.13b Fig.12 LPM000-LEAD-03 - Front Fig.13a LPM000-LEAD-04 - Output panel signal cable signal cable (length of the cable 1.8m) (length of the cable 0.75m) Fig.13b LPM000-LEAD-05 - Output power cable for modules K-N (length of the cable 0.75m) 10.2 Signal Output wire colors Pin # Signal Name by Modules E, F, G, H, J Signal Name by Modules K, L, M, N Wire Color 1 VS+ PG_HI_A Red 2 VS- PG_LO_A Blue 3 CSH INH_HI_A Yellow 4 Common INH_LO_A White 5 N/C N/C - 6 N/C N/C - 7 PG_HI PG_HI_B Violet 8 PG_LO PG_LO_B Brown 9 INH_HI INH_HI_B Black 10 INH_LO INH_LO_B Green BCD.00365 Rev. AA, 21-May-14 Page 17 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules 10.3 Paralleling Busbars (only for modules E-J) Item Description LPM000-BBAR-07 Busbar for parallel connection of two modules, central screw M5, max. 100A 1. Two pieces are in one package LPM000-BBAR-07. LPM000-BBAR-08 Busbar washer with 1 opening for odd module paralleling. Two pieces are in one package LPM000-BBAR-08. Notes: Model 1 For load current over 100A use two or more cables connected to separate busbars. 2 By using busbars (paralleling modules) you will need also the signal output leads LPM000-LEAD-04, one for each connected module. The interconnection is shown in Fig.17 (especially all pins 3 - CSH and all pins 4 - Common must be reconnected). 3 Modules K-N cannot be connected in parallel. The example of LPM409-00EE-DXXX assembly configuration (two modules in parallel) is on Fig.14. One set of busbars LPM000-BBAR-07 + 2x LPM-LEAD-04 is necessary for connection. Fig.14 LPM409-00EE-DXXX Parallel Configuration Fig.15 LPM409-0EEE-DXXX Parallel Configuration An example of an LPM409-0EEE-DXXX assembly configuration (three modules in parallel) is on Fig.15. Two sets of busbars LPM000-BBAR-07 + one set of LPM000-BBAR-08 + 3x LPM-LEAD-04 are necessary to make the interconnections. Note, that for odd number of modules in parallel it is necessary to also use one set of busbar washers LPM000BBAR-08. To connect the load in case of higher output currents, more output cables must be used for each pole. For example for 200A output current (LPM409-EEEE-DXXX) connect minimal two power cables for each pole (2x 2 42mm for one pole). Use min. 105C thermal class isolation. BCD.00365 Rev. AA, 21-May-14 Page 18 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Fig.16 LPM409 - Paralleling Connection Diagram for LPM126 Modules 10.4 Serial Busbars (only for modules E-J) Item Description LPM000-BBAR-09 Busbar for serial connection of two modules. Model Fig.17 LPM409-0EEE-DXXX Serial Configuration BCD.00365 Rev. AA, 21-May-14 Page 19 of 20 www.power-one.com LPM/LMM409 AC-DC Modular Power Supply Data Sheet 5V, 10V, 12V, 20V, 24V, 36V & 48V Single-Output Modules 10V, 20V Dual-Output Modules Fig.18 LPM409 - Serial Connection Diagram for LPM126 Modules NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. BCD.00365 Rev. AA, 21-May-14 Page 20 of 20 www.power-one.com