8/16-bit Atmel XMEGA A1U Microcontroller ATxmega128A1U; ATxmega64A1U Features High-performance, low-power Atmel(R) AVR(R) XMEGA(R) 8/16-bit Microcontroller Nonvolatile program and data memories 64K - 128KBytes of in-system self-programmable flash 4K - 8KBytes boot section 2KBytes EEPROM 4K - 8KBytes internal SRAM External bus interface for up to 16Mbytes SRAM External bus interface for up to 128Mbit SDRAM Peripheral features Four-channel DMA controller Eight-channel event system Eight 16-bit timer/counters Four timer/counters with 4 output compare or input capture channels Four timer/counters with 2 output compare or input capture channels High resolution extension on all timer/counters Advanced waveform extension (AWeX) on two timer/counters One USB device interface USB 2.0 full speed (12Mbps) and low speed (1.5Mbps) device compliant 32 Endpoints with full configuration flexibility Eight USARTs with IrDA support for one USART Four two-wire interfaces with dual address match (I2C and SMBus compatible) Four serial peripheral interfaces (SPIs) AES and DES crypto engine CRC-16 (CRC-CCITT) and CRC-32 (IEEE(R) 802.3) generator 16-bit real time counter (RTC) with separate oscillator Two sixteen channel, 12-bit, 2msps Analog to Digital Converters Two Two-channel, 12-bit, 1msps Digital to Analog Converters Four Analog Comparators (ACs) with window compare function, and current sources External interrupts on all general purpose I/O pins Programmable watchdog timer with separate on-chip ultra low power oscillator QTouch(R) library support Capacitive touch buttons, sliders and wheels Special microcontroller features Power-on reset and programmable brown-out detection Internal and external clock options with PLL and prescaler Programmable multilevel interrupt controller Five sleep modes Programming and debug interfaces JTAG (IEEE 1149.1 compliant) interface, including boundary scan PDI (Program and Debug Interface) I/O and packages 78 Programmable I/O pins 100 lead TQFP 100 ball BGA 100 ball VFBGA Operating voltage 1.6 - 3.6V Operating frequency 0 - 12MHz from 1.6V 0 - 32MHz from 2.7V 8385G-AVR-11/2013 1. Ordering Information Flash (bytes) EEPROM (bytes) SRAM (bytes) ATxmega128A1U-AU 128K + 8K 2K 8K ATxmega128A1U-AUR(4) 128K + 8K 2K 8K ATxmega64A1U-AU 64K + 4K 2K 4K ATxmega64A1U-AUR(4) 64K + 4K 2K 4K ATxmega128A1U-CU 128K + 8K 2K 8K ATxmega128A1U-CUR(4) 128K + 8K 2K 8K ATxmega64A1U-CU 64K + 4K 2K 4K ATxmega64A1U-CUR(4) 64K + 4K 2K 4K ATxmega128A1U-C7U 128K + 8K 2K 8K ATxmega128A1U-C7UR(4) 128K + 8K 2K 8K ATxmega64A1U-C7U 64K + 4K 2K 4K ATxmega64A1U-C7UR(4) 64K + 4K 2K 4K Ordering code Speed (MHz) Power supply Package (1)(2)(3) Temp. 100A 32 1.6 - 3.6V 100C1 -40C - 85C 100C2 Notes: 1. 2. 3. 4. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. For packaging information, see "Packaging information" on page 71. Tape and Reel. Package Type 100A 100-lead, 14 x 14 x 1.0mm, 0.5mm lead pitch, thin profile plastic quad flat package (TQFP) 100C1 100-ball, 9 x 9 x 1.2mm body, ball pitch 0.80mm, chip ball grid array (CBGA) 100C2 100-ball, 7 x 7 x 1.0mm body, ball pitch 0.65mm, very thin fine-pitch ball grid array (VFBGA) Typical Applications Industrial control Climate control Low power battery applications Factory automation RF and ZigBee(R) Power tools Building control USB connectivity HVAC Board control Sensor control Utility metering White goods Optical Medical applications XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 2 2. Pinout/Block Diagram Figure 2-1. Block diagram and pinout. PA2 PA1 PA0 AVCC GND PR1 PR0 PDI/ RESET PDI PQ3 PQ2 PQ1 PQ0 GND VCC PK7 PK6 PK5 PK4 PK3 PK2 PK1 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 60 PH5 59 PH4 58 PH3 57 PH2 56 PH1 55 PH0 54 VCC 53 GND 52 PF7 51 PF6 JTAG FLASH EEPROM DATA BUS 40 41 42 43 44 PE5 PE6 PE7 GND VCC TWI 50 39 PE4 PF5 38 PE3 49 37 PE2 PF4 36 PE1 Port F 48 35 Port E PE0 Port D PF3 Port C SPI EVENT ROUTING NETWORK Port K Port J Port H External Bus Interface SRAM 34 25 PH6 VCC PD0 61 AC0:1 33 24 PH7 CPU GND VCC 62 DAC 32 23 GND DMA Controller PD7 GND 63 Internal Reference 31 22 VCC PD6 PC7 64 BUS matrix 30 21 PJ0 Interrupt Controller PD5 PC6 65 ADC IRCOM 20 PJ1 29 PC5 66 PD4 19 PJ2 28 PC4 Prog/Debug Interface 67 OCD PD3 18 Crypto / CRC 27 PC3 Event System Controller PD2 17 PJ3 AREF 16 PC2 68 AC0:1 26 PC1 PJ4 USART0:1 15 69 47 14 PC0 Reset Controller PF2 VCC Watchdog Timer TC0:1 13 Real Time Counter 46 GND Sleep Controller DAC PF1 12 PJ5 45 PB7 70 ADC PF0 11 PJ6 TWI PB6 PJ7 SPI 10 GND 71 USART0:1 PB5 73 72 AREF 9 VCC Power Supervision PD1 PB4 8 74 Watchdog Oscillator TC0:1 7 PK0 Internal Oscillators USB PB2 75 OSC/CLK Control TWI 6 DATA BUS SPI PB1 TOSC USART0:1 5 XOSC TC0:1 4 PB0 Port Q TWI AVCC Port R SPI 3 USART0:1 GND TC0:1 2 Port A PA7 PB3 PA3 1 Port B PA6 98 EBI PA4 General Purpose I/O Analog function / Oscillators 99 External clock / Crystal pins Digital function PA5 Programming, debug, test 100 Power Ground For details on pinout and pin functions refer to "Pinout and Pin Functions" on page 56. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 3 Figure 2-2. BGA-pinout. Top view 1 2 3 4 5 6 Bottom view 7 8 9 10 10 9 8 7 6 5 4 3 2 1 A A B B C C D D E E F F G G H H J J K K Table 2-1. BGA-pinout. 1 2 3 4 5 6 7 8 9 10 A PK0 VCC GND PJ3 VCC GND PH1 GND VCC PF7 B PK3 PK2 PK1 PJ4 PH7 PH4 PH2 PH0 PF6 PF5 C VCC PK5 PK4 PJ5 PJ0 PH5 PH3 PF2 PF3 VCC D GND PK6 PK7 PJ6 PJ1 PH6 PF0 PF1 PF4 GND E PQ0 PQ1 PQ2 PJ7 PJ2 PE7 PE6 PE5 PE4 PE3 F PR1 PR0 RESET/ PDI_CLK PDI_DATA PQ3 PC2 PE2 PE1 PE0 VCC G GND PA1 PA4 PB3 PB4 PC1 PC6 PD7 PD6 GND H AVCC PA2 PA5 PB2 PB5 PC0 PC5 PD5 PD4 PD3 J PA0 PA3 PB0 PB1 PB6 PC3 PC4 PC7 PD2 PD1 K PA6 PA7 GND AVCC PB7 VCC GND VCC GND PD0 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 4 3. Overview The Atmel AVR XMEGA is a family of low power, high performance, and peripheral rich 8/16-bit microcontrollers based on the AVR enhanced RISC architecture. By executing instructions in a single clock cycle, the AVR XMEGA devices achieve CPU throughput approaching one million instructions per second (MIPS) per megahertz, allowing the system designer to optimize power consumption versus processing speed. The Atmel AVR CPU combines a rich instruction set with 32 general purpose working registers. All 32 registers are directly connected to the arithmetic logic unit (ALU), allowing two independent registers to be accessed in a single instruction, executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs many times faster than conventional single-accumulator or CISC based microcontrollers. The AVR XMEGA A1U devices provide the following features: in-system programmable flash with read-while-write capabilities; internal EEPROM and SRAM; four-channel DMA controller, eight-channel event system and programmable multilevel interrupt controller, 78 general purpose I/O lines, 16-bit real-time counter (RTC); eight flexible, 16-bit timer/counters with compare and PWM channels, eight USARTs; four two-wire serial interfaces (TWIs); one full speed USB 2.0 interface; four serial peripheral interfaces (SPIs); AES and DES cryptographic engine; CRC-16 (CRC-CCITT) and CRC-32 (IEEE 802.3) generator; two 16-channel, 12-bit ADCs with programmable gain; two 2-channel, 12-bit DACs; four Analog Comparators (ACs) with window mode; programmable watchdog timer with separate internal oscillator; accurate internal oscillators with PLL and prescaler; and programmable brown-out detection. The program and debug interface (PDI), a fast, two-pin interface for programming and debugging, is available. The devices also have an IEEE std. 1149.1 compliant JTAG interface, and this can also be used for boundary scan, on-chip debug and programming. The XMEGA A1U devices have five software selectable power saving modes. The idle mode stops the CPU while allowing the SRAM, DMA controller, event system, interrupt controller, and all peripherals to continue functioning. The power-down mode saves the SRAM and register contents, but stops the oscillators, disabling all other functions until the next TWI, USB resume, or pin-change interrupt, or reset. In power-save mode, the asynchronous real-time counter continues to run, allowing the application to maintain a timer base while the rest of the device is sleeping. In standby mode, the external crystal oscillator keeps running while the rest of the device is sleeping. This allows very fast startup from the external crystal, combined with low power consumption. In extended standby mode, both the main oscillator and the asynchronous timer continue to run. To further reduce power consumption, the peripheral clock to each individual peripheral can optionally be stopped in active mode and idle sleep mode. Atmel offers a free QTouch library for embedding capacitive touch buttons, sliders and wheels functionality into AVR microcontrollers. The device are manufactured using Atmel high-density, nonvolatile memory technology. The program flash memory can be reprogrammed in-system through the PDI or JTAG interfaces. A boot loader running in the device can use any interface to download the application program to the flash memory. The boot loader software in the boot flash section will continue to run while the application flash section is updated, providing true read-while-write operation. By combining an 8/16-bit RISC CPU with in-system, self-programmable flash, the AVR XMEGA is a powerful microcontroller family that provides a highly flexible and cost effective solution for many embedded applications. All Atmel AVR XMEGA devices are supported with a full suite of program and system development tools, including C compilers, macro assemblers, program debugger/simulators, programmers, and evaluation kits. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 5 3.1 Block Diagram Figure 3-1. XMEGA A1U Block Diagram. Digital function Bus masters, programming, debug, test Analog function EBI Oscillator/Crystal/Clock PR[0..1] XTAL1 PQ[0..3] TOSC1 General Purpose I/O XTAL2 TOSC2 PORT R (2) PORT Q (4) Real Time Counter Watchdog Oscillator DATA BUS DACA PA[0..7] Oscillator Circuits/ Clock Generation PORT A (8) Watchdog Timer Event System Controller Oscillator Control DMA Controller ADCA VCC Power Supervision POR/BOD & RESET SRAM ACA Sleep Controller GND RESET/ PDI_CLK AREFA PDI Prog/Debug Controller BUS Matrix PDI_DATA VCC/10 Int. Refs. AES Tempref JTAG OCD AREFB PORT B DES Interrupt Controller CPU ADCB PORT K (8) PK[0..7] PORT J (8) PJ[0..7] CRC ACB NVM Controller EBI PORT B (8) Flash PORT E/F EEPROM PORT H (8) DACB IRCOM PH[0..7] DATA BUS PORT D (8) PORT E (8) PC[0..7] PD[0..7] PE[0..7] SPIF TWIF TCF0:1 USARTF0:1 SPIE PORT C (8) TWIE TCE0:1 USARTE0:1 USB SPID TWID TCD0:1 USARTD0:1 SPIC TWIC TCC0:1 EVENT ROUTING NETWORK USARTC0:1 PB[0..7]/ JTAG PORT F (8) PF[0..7] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 6 4. Resources A comprehensive set of development tools, application notes and datasheets are available for download on http://www.atmel.com/avr. 4.1 Recommended reading Atmel AVR XMEGA AU manual XMEGA application notes This device data sheet only contains part specific information with a short description of each peripheral and module. The XMEGA AU manual describes the modules and peripherals in depth. The XMEGA application notes contain example code and show applied use of the modules and peripherals. All documentations are available from www.atmel.com/avr. 5. Capacitive touch sensing The Atmel QTouch library provides a simple to use solution to realize touch sensitive interfaces on most Atmel AVR microcontrollers. The patented charge-transfer signal acquisition offers robust sensing and includes fully debounced reporting of touch keys and includes Adjacent Key Suppression(R) (AKS(R)) technology for unambiguous detection of key events. The QTouch library includes support for the QTouch and QMatrix acquisition methods. Touch sensing can be added to any application by linking the appropriate Atmel QTouch library for the AVR microcontroller. This is done by using a simple set of APIs to define the touch channels and sensors, and then calling the touch sensing API's to retrieve the channel information and determine the touch sensor states. The QTouch library is FREE and downloadable from the Atmel website at the following location: www.atmel.com/qtouchlibrary. For implementation details and other information, refer to the QTouch library user guide also available for download from the Atmel website. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 7 6. AVR CPU 6.1 Features 8/16-bit, high-performance Atmel AVR RISC CPU 142 instructions Hardware multiplier 32x8-bit registers directly connected to the ALU Stack in RAM Stack pointer accessible in I/O memory space Direct addressing of up to 16MB of program memory and 16MB of data memory True 16/24-bit access to 16/24-bit I/O registers Efficient support for 8-, 16-, and 32-bit arithmetic Configuration change protection of system-critical features 6.2 Overview All Atmel AVR XMEGA devices use the 8/16-bit AVR CPU. The main function of the CPU is to execute the code and perform all calculations. The CPU is able to access memories, perform calculations, control peripherals, and execute the program in the flash memory. Interrupt handling is described in a separate section, refer to "Interrupts and Programmable Multilevel Interrupt Controller" on page 27. 6.3 Architectural Overview In order to maximize performance and parallelism, the AVR CPU uses a Harvard architecture with separate memories and buses for program and data. Instructions in the program memory are executed with single-level pipelining. While one instruction is being executed, the next instruction is pre-fetched from the program memory. This enables instructions to be executed on every clock cycle. For details of all AVR instructions, refer to http://www.atmel.com/avr. Figure 6-1. Block diagram of the AVR CPU architecture. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 8 The arithmetic logic unit (ALU) supports arithmetic and logic operations between registers or between a constant and a register. Single-register operations can also be executed in the ALU. After an arithmetic operation, the status register is updated to reflect information about the result of the operation. The ALU is directly connected to the fast-access register file. The 32 x 8-bit general purpose working registers all have single clock cycle access time allowing single-cycle arithmetic logic unit (ALU) operation between registers or between a register and an immediate. Six of the 32 registers can be used as three 16-bit address pointers for program and data space addressing, enabling efficient address calculations. The memory spaces are linear. The data memory space and the program memory space are two different memory spaces. The data memory space is divided into I/O registers, SRAM, and external RAM. In addition, the EEPROM can be memory mapped in the data memory. All I/O status and control registers reside in the lowest 4KB addresses of the data memory. This is referred to as the I/O memory space. The lowest 64 addresses can be accessed directly, or as the data space locations from 0x00 to 0x3F. The rest is the extended I/O memory space, ranging from 0x0040 to 0x0FFF. I/O registers here must be accessed as data space locations using load (LD/LDS/LDD) and store (ST/STS/STD) instructions. The SRAM holds data. Code execution from SRAM is not supported. It can easily be accessed through the five different addressing modes supported in the AVR architecture. The first SRAM address is 0x2000. Data addresses 0x1000 to 0x1FFF are reserved for memory mapping of EEPROM. The program memory is divided in two sections, the application program section and the boot program section. Both sections have dedicated lock bits for write and read/write protection. The SPM instruction that is used for selfprogramming of the application flash memory must reside in the boot program section. The application section contains an application table section with separate lock bits for write and read/write protection. The application table section can be used for safe storing of nonvolatile data in the program memory. 6.4 ALU - Arithmetic Logic Unit The arithmetic logic unit (ALU) supports arithmetic and logic operations between registers or between a constant and a register. Single-register operations can also be executed. The ALU operates in direct connection with all 32 general purpose registers. In a single clock cycle, arithmetic operations between general purpose registers or between a register and an immediate are executed and the result is stored in the register file. After an arithmetic or logic operation, the status register is updated to reflect information about the result of the operation. ALU operations are divided into three main categories - arithmetic, logical, and bit functions. Both 8- and 16-bit arithmetic is supported, and the instruction set allows for efficient implementation of 32-bit aritmetic. The hardware multiplier supports signed and unsigned multiplication and fractional format. 6.4.1 Hardware Multiplier The multiplier is capable of multiplying two 8-bit numbers into a 16-bit result. The hardware multiplier supports different variations of signed and unsigned integer and fractional numbers: Multiplication of unsigned integers Multiplication of signed integers Multiplication of a signed integer with an unsigned integer Multiplication of unsigned fractional numbers Multiplication of signed fractional numbers Multiplication of a signed fractional number with an unsigned one A multiplication takes two CPU clock cycles. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 9 6.5 Program Flow After reset, the CPU starts to execute instructions from the lowest address in the flash programmemory `0.' The program counter (PC) addresses the next instruction to be fetched. Program flow is provided by conditional and unconditional jump and call instructions capable of addressing the whole address space directly. Most AVR instructions use a 16-bit word format, while a limited number use a 32-bit format. During interrupts and subroutine calls, the return address PC is stored on the stack. The stack is allocated in the general data SRAM, and consequently the stack size is only limited by the total SRAM size and the usage of the SRAM. After reset, the stack pointer (SP) points to the highest address in the internal SRAM. The SP is read/write accessible in the I/O memory space, enabling easy implementation of multiple stacks or stack areas. The data SRAM can easily be accessed through the five different addressing modes supported in the AVR CPU. 6.6 Status Register The status register (SREG) contains information about the result of the most recently executed arithmetic or logic instruction. This information can be used for altering program flow in order to perform conditional operations. Note that the status register is updated after all ALU operations, as specified in the instruction set reference. This will in many cases remove the need for using the dedicated compare instructions, resulting in faster and more compact code. The status register is not automatically stored when entering an interrupt routine nor restored when returning from an interrupt. This must be handled by software. The status register is accessible in the I/O memory space. 6.7 Stack and Stack Pointer The stack is used for storing return addresses after interrupts and subroutine calls. It can also be used for storing temporary data. The stack pointer (SP) register always points to the top of the stack. It is implemented as two 8-bit registers that are accessible in the I/O memory space. Data are pushed and popped from the stack using the PUSH and POP instructions. The stack grows from a higher memory location to a lower memory location. This implies that pushing data onto the stack decreases the SP, and popping data off the stack increases the SP. The SP is automatically loaded after reset, and the initial value is the highest address of the internal SRAM. If the SP is changed, it must be set to point above address 0x2000, and it must be defined before any subroutine calls are executed or before interrupts are enabled. During interrupts or subroutine calls, the return address is automatically pushed on the stack. The return address can be two or three bytes, depending on program memory size of the device. For devices with 128KB or less of program memory, the return address is two bytes, and hence the stack pointer is decremented/incremented by two. For devices with more than 128KB of program memory, the return address is three bytes, and hence the SP is decremented/incremented by three. The return address is popped off the stack when returning from interrupts using the RETI instruction, and from subroutine calls using the RET instruction. The SP is decremented by one when data are pushed on the stack with the PUSH instruction, and incremented by one when data is popped off the stack using the POP instruction. To prevent corruption when updating the stack pointer from software, a write to SPL will automatically disable interrupts for up to four instructions or until the next I/O memory write. After reset the stack pointer is initialized to the highest address of the SRAM. See Figure 7-2 on page 14. 6.8 Register File The register file consists of 32 x 8-bit general purpose working registers with single clock cycle access time. The register file supports the following input/output schemes: One 8-bit output operand and one 8-bit result input Two 8-bit output operands and one 8-bit result input Two 8-bit output operands and one 16-bit result input One 16-bit output operand and one 16-bit result input XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 10 Six of the 32 registers can be used as three 16-bit address register pointers for data space addressing, enabling efficient address calculations. One of these address pointers can also be used as an address pointer for lookup tables in flash program memory. 7. Memories 7.1 Features Flash program memory One linear address space In-system programmable Self-programming and boot loader support Application section for application code Application table section for application code or data storage Boot section for application code or boot loader code Separate read/write protection lock bits for all sections Built in fast CRC check of a selectable flash program memory section Data memory One linear address space Single-cycle access from CPU SRAM EEPROM Byte and page accessible Optional memory mapping for direct load and store I/O memory Configuration and status registers for all peripherals and modules 16 bit-accessible general purpose register for global variables or flags External memory support SRAM SDRAM Memory mapped external hardware Bus arbitration Deterministic priority handling between CPU, DMA controller, and other bus masters Separate buses for SRAM, EEPROM, I/O memory and external memory Simultaneous bus access for CPU and DMA controller Production signature row memory for factory programmed data ID for each microcontroller device type Serial number for each device Calibration bytes for factory calibrated peripherals User signature row One flash page in size Can be read and written from software Content is kept after chip erase 7.2 Overview The Atmel AVR architecture has two main memory spaces, the program memory and the data memory. Executable code can reside only in the program memory, while data can be stored in the program memory and the data memory. The data memory includes the internal SRAM, and EEPROM for nonvolatile data storage. All memory spaces are linear and require no memory bank switching. Nonvolatile memory (NVM) spaces can be locked for further write and read/write operations. This prevents unrestricted access to the application software. A separate memory section contains the fuse bytes. These are used for configuring important system functions, and can only be written by an external programmer. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 11 The available memory size configurations are shown in "Ordering Information" on page 2. In addition each device has a flash memory signature rows for calibration data, device identification, serial number etc. 7.3 Flash Program Memory The Atmel AVR XMEGA devices contain on-chip, in-system reprogrammable flash memory for program storage. The flash memory can be accessed for read and write from an external programmer through the PDI or from application software running in the device. All AVR CPU instructions are 16 or 32 bits wide, and each flash location is 16 bits wide. The flash memory is organized in two main sections, the application section and the boot loader section. The sizes of the different sections are fixed, but device-dependent. These two sections have separate lock bits, and can have different levels of protection. The store program memory (SPM) instruction, which is used to write to the flash from the application software, will only operate when executed from the boot loader section. The application section contains an application table section with separate lock settings. This enables safe storage of nonvolatile data in the program memory. Figure 7-1. Flash program memory (Hexadecimal address). Word Address ATxmega128A1U ATxmega64A1U 0 0 Application Section (bytes) (128K/64K) ... 7.3.1 EFFF / 77FF F000 / 7800 FFFF / 7FFF Application Table Section (bytes) (8K/4K) 10000 / 8000 Boot Section (bytes) 10FFF / 87FF (8K/4K) Application Section The Application section is the section of the flash that is used for storing the executable application code. The protection level for the application section can be selected by the boot lock bits for this section. The application section can not store any boot loader code since the SPM instruction cannot be executed from the application section. 7.3.2 Application Table Section The application table section is a part of the application section of the flash memory that can be used for storing data. The size is identical to the boot loader section. The protection level for the application table section can be selected by the boot lock bits for this section. The possibilities for different protection levels on the application section and the application table section enable safe parameter storage in the program memory. If this section is not used for data, application code can reside here. 7.3.3 Boot Loader Section While the application section is used for storing the application code, the boot loader software must be located in the boot loader section because the SPM instruction can only initiate programming when executing from this section. The SPM instruction can access the entire flash, including the boot loader section itself. The protection level for the boot loader section can be selected by the boot loader lock bits. If this section is not used for boot loader software, application code can be stored here. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 12 7.3.4 Production Signature Row The production signature row is a separate memory section for factory programmed data. It contains calibration data for functions such as oscillators and analog modules. Some of the calibration values will be automatically loaded to the corresponding module or peripheral unit during reset. Other values must be loaded from the signature row and written to the corresponding peripheral registers from software. For details on calibration conditions, refer to "Electrical Characteristics" on page 74. The production signature row also contains an ID that identifies each microcontroller device type and a serial number for each manufactured device. The serial number consists of the production lot number, wafer number, and wafer coordinates for the device. The device ID for the available devices is shown in Table 7-1. The production signature row cannot be written or erased, but it can be read from application software and external programmers. Table 7-1. Device ID bytes. Device 7.3.5 Device ID bytes Byte 2 Byte 1 Byte 0 ATxmega64A1U 4E 96 1E ATxmega128A1U 4C 97 1E User Signature Row The user signature row is a separate memory section that is fully accessible (read and write) from application software and external programmers. It is one flash page in size, and is meant for static user parameter storage, such as calibration data, custom serial number, identification numbers, random number seeds, etc. This section is not erased by chip erase commands that erase the flash, and requires a dedicated erase command. This ensures parameter storage during multiple program/erase operations and on-chip debug sessions. 7.4 Fuses and Lock bits The fuses are used to configure important system functions, and can only be written from an external programmer. The application software can read the fuses. The fuses are used to configure reset sources such as brownout detector and watchdog, startup configuration, JTAG enable, and JTAG user ID. The lock bits are used to set protection levels for the different flash sections (that is, if read and/or write access should be blocked). Lock bits can be written by external programmers and application software, but only to stricter protection levels. Chip erase is the only way to erase the lock bits. To ensure that flash contents are protected even during chip erase, the lock bits are erased after the rest of the flash memory has been erased. An unprogrammed fuse or lock bit will have the value one, while a programmed fuse or lock bit will have the value zero. Both fuses and lock bits are reprogrammable like the flash program memory. 7.5 Data Memory The data memory contains the I/O memory, internal SRAM, optionally memory mapped EEPROM, and external memory if available. The data memory is organized as one continuous memory section, see Figure 7-2 on page 14. To simplify development, I/O Memory, EEPROM and SRAM will always have the same start addresses for all Atmel AVR XMEGA devices. The address space for External Memory will always start at the end of Internal SRAM and end at address 0xFFFFFF. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 13 Figure 7-2. Data memory map (hexadecimal address). Byte Address ATxmega64A1U 0 Byte Address 0 I/O Registers (4K) FFF I/O Registers (4KB) FFF 1000 1000 EEPROM (2K) 17FF EEPROM (2K) 17FF RESERVED 2000 RESERVED 2000 Internal SRAM (4K) 2FFF Internal SRAM (8K) 3FFF 4000 3000 External Memory (0 to 16MB) FFFFFF 7.6 ATxmega128A1U External Memory (0 to 16MB) FFFFFF EEPROM XMEGA AU devices have EEPROM for nonvolatile data storage. It is either addressable in a separate data space (default) or memory mapped and accessed in normal data space. The EEPROM supports both byte and page access. Memory mapped EEPROM allows highly efficient EEPROM reading and EEPROM buffer loading. When doing this, EEPROM is accessible using load and store instructions. Memory mapped EEPROM will always start at hexadecimal address 0x1000. 7.7 I/O Memory The status and configuration registers for peripherals and modules, including the CPU, are addressable through I/O memory locations. All I/O locations can be accessed by the load (LD/LDS/LDD) and store (ST/STS/STD) instructions, which is used to transfer data between the 32 registers in the register file and the I/O memory. The IN and OUT instructions can address I/O memory locations in the range 0x00 - 0x3F directly. In the address range 0x00 - 0x1F, single- cycle instructions for manipulation and checking of individual bits are available. The I/O memory address for all peripherals and modules in XMEGA A1U is shown in the "Peripheral Module Address Map" on page 63. 7.7.1 General Purpose I/O Registers The lowest 16 I/O memory addresses are reserved as general purpose I/O registers. These registers can be used for storing global variables and flags, as they are directly bit-accessible using the SBI, CBI, SBIS, and SBIC instructions. 7.8 External Memory Four ports can be used for external memory, supporting external SRAM, SDRAM, and memory mapped peripherals such as LCD displays. Refer to "EBI - External Bus Interface" on page 48. The external memory address space will always start at the end of internal SRAM. 7.9 Data Memory and Bus Arbitration Since the data memory is organized as four separate sets of memories, the different bus masters (CPU, DMA controller read and DMA controller write, etc.) can access different memory sections at the same time. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 14 7.10 Memory Timing Read and write access to the I/O memory takes one CPU clock cycle. A write to SRAM takes one cycle, and a read from SRAM takes two cycles. For burst read (DMA), new data are available every cycle. EEPROM page load (write) takes one cycle, and three cycles are required for read. For burst read, new data are available every second cycle. External memory has multi-cycle read and write. The number of cycles depends on the type of memory and configuration of the external bus interface. Refer to the instruction summary for more details on instructions and instruction timing. 7.11 Device ID and Revision Each device has a three-byte device ID. This ID identifies Atmel as the manufacturer of the device and the device type. A separate register contains the revision number of the device. 7.12 I/O Memory Protection Some features in the device are regarded as critical for safety in some applications. Due to this, it is possible to lock the I/O register related to the clock system, the event system, and the advanced waveform extensions. As long as the lock is enabled, all related I/O registers are locked and they can not be written from the application software. The lock registers themselves are protected by the configuration change protection mechanism. 7.13 JTAG Disable It is possible to disable the JTAG interface from the application software. This will prevent all external JTAG access to the device until the next device reset or until JTAG is enabled again from the application software. As long as JTAG is disabled, the I/O pins required for JTAG can be used as normal I/O pins. 7.14 Flash and EEPROM Page Size The flash program memory and EEPROM data memory are organized in pages. The pages are word accessible for the flash and byte accessible for the EEPROM. Table 7-2 on page 15 shows the Flash Program Memory organization. Flash write and erase operations are performed on one page at a time, while reading the Flash is done one byte at a time. For Flash access the Z-pointer (Z[m:n]) is used for addressing. The most significant bits in the address (FPAGE) gives the page number and the least significant address bits (FWORD) gives the word in the page. Table 7-2. Number of words and Pages in the Flash. Devices PC size bits Flash bytes Page Size FWORD FPAGE words Application Size No of pages Boot Size No of pages ATxmega64A1U 16 64K + 4K 128 Z[7:1] Z[16:8] 64K 256 4K 16 ATxmega128A1U 17 128K + 8K 256 Z[8:1] Z[17:9] 128K 256 8K 16 Table 7-3 on page 16 shows EEPROM memory organization for the Atmel AVR XMEGA A1U devices. EEPROM write and erase operations can be performed one page or one byte at a time, while reading the EEPROM is done one byte at a time. For EEPROM access the NVM Address Register (ADDR[m:n]) is used for addressing. The most significant bits in the address (E2PAGE) give the page number and the least significant address bits (E2BYTE) give the byte in the page. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 15 Table 7-3. Number of Bytes and Pages in the EEPROM. Devices EEPROM Page Size E2BYTE E2PAGE No of Pages Size bytes ATxmega64A1U 2K 32 ADDR[4:0] ADDR[10:5] 64 ATxmega128A1U 2K 32 ADDR[4:0] ADDR[10:5] 64 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 16 8. DMAC - Direct Memory Access Controller 8.1 Features Allows high speed data transfers with minimal CPU intervention from data memory to data memory from data memory to peripheral from peripheral to data memory from peripheral to peripheral Four DMA channels with separate transfer triggers interrupt vectors addressing modes Programmable channel priority From 1 byte to 16MB of data in a single transaction Up to 64KB block transfers with repeat 1, 2, 4, or 8 byte burst transfers Multiple addressing modes Static Incremental Decremental Optional reload of source and destination addresses at the end of each Burst Block Transaction Optional interrupt on end of transaction Optional connection to CRC generator for CRC on DMA data 8.2 Overview The four-channel direct memory access (DMA) controller can transfer data between memories and peripherals, and thus offload these tasks from the CPU. It enables high data transfer rates with minimum CPU intervention, and frees up CPU time. The four DMA channels enable up to four independent and parallel transfers. The DMA controller can move data between SRAM and peripherals, between SRAM locations and directly between peripheral registers. With access to all peripherals, the DMA controller can handle automatic transfer of data to/from communication modules. The DMA controller can also read from memory mapped EEPROM. Data transfers are done in continuous bursts of 1, 2, 4, or 8 bytes. They build block transfers of configurable size from 1 byte to 64KB. A repeat counter can be used to repeat each block transfer for single transactions up to 16MB. Source and destination addressing can be static, incremental or decremental. Automatic reload of source and/or destination addresses can be done after each burst or block transfer, or when a transaction is complete. Application software, peripherals, and events can trigger DMA transfers. The four DMA channels have individual configuration and control settings. This include source, destination, transfer triggers, and transaction sizes. They have individual interrupt settings. Interrupt requests can be generated when a transaction is complete or when the DMA controller detects an error on a DMA channel. To allow for continuous transfers, two channels can be interlinked so that the second takes over the transfer when the first is finished, and vice versa. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 17 9. Event System 9.1 Features System for direct peripheral-to-peripheral communication and signaling Peripherals can directly send, receive, and react to peripheral events CPU and DMA controller independent operation 100% predictable signal timing Short and guaranteed response time Eight event channels for up to eight different and parallel signal routing configurations Events can be sent and/or used by most peripherals, clock system, and software Additional functions include Quadrature decoders Digital filtering of I/O pin state Works in active mode and idle sleep mode 9.2 Overview The event system enables direct peripheral-to-peripheral communication and signaling. It allows a change in one peripheral's state to automatically trigger actions in other peripherals. It is designed to provide a predictable system for short and predictable response times between peripherals. It allows for autonomous peripheral control and interaction without the use of interrupts, CPU, or DMA controller resources, and is thus a powerful tool for reducing the complexity, size and execution time of application code. It also allows for synchronized timing of actions in several peripheral modules. A change in a peripheral's state is referred to as an event, and usually corresponds to the peripheral's interrupt conditions. Events can be directly passed to other peripherals using a dedicated routing network called the event routing network. How events are routed and used by the peripherals is configured in software. Figure 9-1 on page 18 shows a basic diagram of all connected peripherals. The event system can directly connect together analog and digital converters, analog comparators, I/O port pins, the real-time counter, timer/counters, IR communication module (IRCOM), and USB interface. It can also be used to trigger DMA transactions (DMA controller). Events can also be generated from software and the peripheral clock. Figure 9-1. Event system overview and connected peripherals. CPU / Software DMA Controller Event Routing Network ADC AC clkPER Prescaler Real Time Counter Event System Controller Timer / Counters DAC USB Port pins IRCOM The event routing network consists of eight software-configurable multiplexers that control how events are routed and used. These are called event channels, and allow for up to eight parallel event routing configurations. The maximum routing latency is two peripheral clock cycles. The event system works in both active mode and idle sleep mode. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 18 10. System Clock and Clock options 10.1 Features Fast start-up time Safe run-time clock switching Internal oscillators: 32MHz run-time calibrated and tunable oscillator 2MHz run-time calibrated oscillator 32.768kHz calibrated oscillator 32kHz ultra low power (ULP) oscillator with 1kHz output External clock options 0.4MHz - 16MHz crystal oscillator 32.768kHz crystal oscillator External clock PLL with 20MHz - 128MHz output frequency Internal and external clock options and 1x to 31x multiplication Lock detector Clock prescalers with 1x to 2048x division Fast peripheral clocks running at two and four times the CPU clock Automatic run-time calibration of internal oscillators External oscillator and PLL lock failure detection with optional non-maskable interrupt 10.2 Overview Atmel AVR XMEGA devices have a flexible clock system supporting a large number of clock sources. It incorporates both accurate internal oscillators and external crystal oscillator and resonator support. A high-frequency phase locked loop (PLL) and clock prescalers can be used to generate a wide range of clock frequencies. A calibration feature (DFLL) is available, and can be used for automatic run-time calibration of the internal oscillators to remove frequency drift over voltage and temperature. An oscillator failure monitor can be enabled to issue a non-maskable interrupt and switch to the internal oscillator if the external oscillator or PLL fails. When a reset occurs, all clock sources except the 32kHz ultra low power oscillator are disabled. After reset, the device will always start up running from the 2MHz internal oscillator. During normal operation, the system clock source and prescalers can be changed from software at any time. Figure 10-1 on page 20 presents the principal clock system in the XMEGA A1U family devices. Not all of the clocks need to be active at a given time. The clocks for the CPU and peripherals can be stopped using sleep modes and power reduction registers as described in "Power Management and Sleep Modes" on page 22. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 19 Figure 10-1. The clock system, clock sources, and clock distribution. Real Time Counter Peripherals RAM AVR CPU Non-Volatile Memory clkPER clkCPU clkPER2 clkPER4 USB clkUSB Brown-out Detector System Clock Prescalers Watchdog Timer Prescaler clkSYS clkRTC System Clock Multiplexer (SCLKSEL) RTCSRC USBSRC DIV32 DIV32 DIV32 PLL PLLSRC DIV4 XOSCSEL 32 kHz Int. ULP 32.768 kHz Int. OSC 32.768 kHz TOSC 32 MHz Int. Osc 2 MHz Int. Osc XTAL2 XTAL1 TOSC2 TOSC1 10.3 0.4 - 16 MHz XTAL Clock Sources The clock sources are divided in two main groups: internal oscillators and external clock sources. Most of the clock sources can be directly enabled and disabled from software, while others are automatically enabled or disabled, depending on peripheral settings. After reset, the device starts up running from the 2MHz internal oscillator. The other clock sources, DFLLs and PLL, are turned off by default. The internal oscillators do not require any external components to run. For details on characteristics and accuracy of the internal oscillators, refer to the device datasheet. 10.3.1 32kHz Ultra Low Power Internal Oscillator This oscillator provides an approximate 32kHz clock. The 32kHz ultra low power (ULP) internal oscillator is a very low power clock source, and it is not designed for high accuracy. The oscillator employs a built-in prescaler that provides a XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 20 1kHz output. The oscillator is automatically enabled/disabled when it is used as clock source for any part of the device. This oscillator can be selected as the clock source for the RTC. 10.3.2 32.768kHz Calibrated Internal Oscillator This oscillator provides an approximate 32.768kHz clock. It is calibrated during production to provide a default frequency close to its nominal frequency. The calibration register can also be written from software for run-time calibration of the oscillator frequency. The oscillator employs a built-in prescaler, which provides both a 32.768kHz output and a 1.024kHz output. 10.3.3 32.768kHz Crystal Oscillator A 32.768kHz crystal oscillator can be connected between the TOSC1 and TOSC2 pins and enables a dedicated low frequency oscillator input circuit. A low power mode with reduced voltage swing on TOSC2 is available. This oscillator can be used as a clock source for the system clock and RTC, and as the DFLL reference clock. 10.3.4 0.4 - 16MHz Crystal Oscillator This oscillator can operate in four different modes optimized for different frequency ranges, all within 0.4 - 16MHz. 10.3.5 2MHz Run-time Calibrated Internal Oscillator The 2MHz run-time calibrated internal oscillator is the default system clock source after reset. It is calibrated during production to provide a default frequency close to its nominal frequency. A DFLL can be enabled for automatic run-time calibration of the oscillator to compensate for temperature and voltage drift and optimize the oscillator accuracy. 10.3.6 32MHz Run-time Calibrated Internal Oscillator The 32MHz run-time calibrated internal oscillator is a high-frequency oscillator. It is calibrated during production to provide a default frequency close to its nominal frequency. A digital frequency looked loop (DFLL) can be enabled for automatic run-time calibration of the oscillator to compensate for temperature and voltage drift and optimize the oscillator accuracy. This oscillator can also be adjusted and calibrated to any frequency between 30MHz and 55MHz. The production signature row contains 48MHz calibration values intended used when the oscillator is used a full-speed USB clock source. 10.3.7 External Clock The XTAL1 and XTAL2 pins can be used to drive an external oscillator, either a quartz crystal or a ceramic resonator. XTAL1 can be used as input for an external clock signal. The TOSC1 and TOSC2 pins is dedicated to driving a 32.768kHz crystal oscillator. 10.3.8 PLL with 1x-31x Multiplication factor The built-in phase locked loop (PLL) can be used to generate a high-frequency system clock. The PLL has a userselectable multiplication factor of from 1 to 31. In combination with the prescalers, this gives a wide range of output frequencies from all clock sources. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 21 11. Power Management and Sleep Modes 11.1 Features Power management for adjusting power consumption and functions Five sleep modes Idle Power down Power save Standby Extended standby Power reduction register to disable clock and turn off unused peripherals in active and idle modes 11.2 Overview Various sleep modes and clock gating are provided in order to tailor power consumption to application requirements. This enables the Atmel AVR XMEGA microcontroller to stop unused modules to save power. All sleep modes are available and can be entered from active mode. In active mode, the CPU is executing application code. When the device enters sleep mode, program execution is stopped and interrupts or a reset is used to wake the device again. The application code decides which sleep mode to enter and when. Interrupts from enabled peripherals and all enabled reset sources can restore the microcontroller from sleep to active mode. In addition, power reduction registers provide a method to stop the clock to individual peripherals from software. When this is done, the current state of the peripheral is frozen, and there is no power consumption from that peripheral. This reduces the power consumption in active mode and idle sleep modes and enables much more fine-tuned power management than sleep modes alone. 11.3 Sleep Modes Sleep modes are used to shut down modules and clock domains in the microcontroller in order to save power. XMEGA microcontrollers have five different sleep modes tuned to match the typical functional stages during application execution. A dedicated sleep instruction (SLEEP) is available to enter sleep mode. Interrupts are used to wake the device from sleep, and the available interrupt wake-up sources are dependent on the configured sleep mode. When an enabled interrupt occurs, the device will wake up and execute the interrupt service routine before continuing normal program execution from the first instruction after the SLEEP instruction. If other, higher priority interrupts are pending when the wake-up occurs, their interrupt service routines will be executed according to their priority before the interrupt service routine for the wake-up interrupt is executed. After wake-up, the CPU is halted for four cycles before execution starts. The content of the register file, SRAM and registers are kept during sleep. If a reset occurs during sleep, the device will reset, start up, and execute from the reset vector. 11.3.1 Idle Mode In idle mode the CPU and nonvolatile memory are stopped (note that any ongoing programming will be completed), but all peripherals, including the interrupt controller, event system and DMA controller are kept running. Any enabled interrupt will wake the device. 11.3.2 Power-down Mode In power-down mode, all clocks, including the real-time counter clock source, are stopped. This allows operation only of asynchronous modules that do not require a running clock. The only interrupts that can wake up the MCU are the twowire interface address match interrupt, asynchronous port interrupts, and the USB resume interrupt. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 22 11.3.3 Power-save Mode Power-save mode is identical to power down, with one exception. If the real-time counter (RTC) is enabled, it will keep running during sleep, and the device can also wake up from either an RTC overflow or compare match interrupt. 11.3.4 Standby Mode Standby mode is identical to power down, with the exception that the enabled system clock sources are kept running while the CPU, peripheral, and RTC clocks are stopped. This reduces the wake-up time. 11.3.5 Extended Standby Mode Extended standby mode is identical to power-save mode, with the exception that the enabled system clock sources are kept running while the CPU and peripheral clocks are stopped. This reduces the wake-up time. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 23 12. System Control and Reset 12.1 Features Reset the microcontroller and set it to initial state when a reset source goes active Multiple reset sources that cover different situations Power-on reset External reset Watchdog reset Brownout reset PDI reset Software reset Asynchronous operation No running system clock in the device is required for reset Reset status register for reading the reset source from the application code 12.2 Overview The reset system issues a microcontroller reset and sets the device to its initial state. This is for situations where operation should not start or continue, such as when the microcontroller operates below its power supply rating. If a reset source goes active, the device enters and is kept in reset until all reset sources have released their reset. The I/O pins are immediately tri-stated. The program counter is set to the reset vector location, and all I/O registers are set to their initial values. The SRAM content is kept. However, if the device accesses the SRAM when a reset occurs, the content of the accessed location can not be guaranteed. After reset is released from all reset sources, the default oscillator is started and calibrated before the device starts running from the reset vector address. By default, this is the lowest program memory address, 0, but it is possible to move the reset vector to the lowest address in the boot section. The reset functionality is asynchronous, and so no running system clock is required to reset the device. The software reset feature makes it possible to issue a controlled system reset from the user software. The reset status register has individual status flags for each reset source. It is cleared at power-on reset, and shows which sources have issued a reset since the last power-on. 12.3 Reset Sequence A reset request from any reset source will immediately reset the device and keep it in reset as long as the request is active. When all reset requests are released, the device will go through three stages before the device starts running again: Reset counter delay Oscillator startup Oscillator calibration If another reset requests occurs during this process, the reset sequence will start over again. 12.4 Reset Sources 12.4.1 Power-on Reset A power-on reset (POR) is generated by an on-chip detection circuit. The POR is activated when the VCC rises and reaches the POR threshold voltage (VPOT), and this will start the reset sequence. The POR is also activated to power down the device properly when the VCC falls and drops below the VPOT level. The VPOT level is higher for falling VCC than for rising VCC. Consult the datasheet for POR characteristics data. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 24 12.4.2 Brownout Detection The on-chip brownout detection (BOD) circuit monitors the VCC level during operation by comparing it to a fixed, programmable level that is selected by the BODLEVEL fuses. If disabled, BOD is forced on at the lowest level during chip erase and when the PDI is enabled. 12.4.3 External Reset The external reset circuit is connected to the external RESET pin. The external reset will trigger when the RESET pin is driven below the RESET pin threshold voltage, VRST, for longer than the minimum pulse period, tEXT. The reset will be held as long as the pin is kept low. The RESET pin includes an internal pull-up resistor. 12.4.4 Watchdog Reset The watchdog timer (WDT) is a system function for monitoring correct program operation. If the WDT is not reset from the software within a programmable timeout period, a watchdog reset will be given. The watchdog reset is active for one to two clock cycles of the 2MHz internal oscillator. For more details see "WDT - Watchdog Timer" on page 26. 12.4.5 Software reset The software reset makes it possible to issue a system reset from software by writing to the software reset bit in the reset control register.The reset will be issued within two CPU clock cycles after writing the bit. It is not possible to execute any instruction from when a software reset is requested until it is issued. 12.4.6 Program and Debug Interface Reset The program and debug interface reset contains a separate reset source that is used to reset the device during external programming and debugging. This reset source is accessible only from external debuggers and programmers. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 25 13. WDT - Watchdog Timer 13.1 Features Issues a device reset if the timer is not reset before its timeout period Asynchronous operation from dedicated oscillator 1kHz output of the 32kHz ultra low power oscillator 11 selectable timeout periods, from 8ms to 8s Two operation modes: Normal mode Window mode Configuration lock to prevent unwanted changes 13.2 Overview The watchdog timer (WDT) is a system function for monitoring correct program operation. It makes it possible to recover from error situations such as runaway or deadlocked code. The WDT is a timer, configured to a predefined timeout period, and is constantly running when enabled. If the WDT is not reset within the timeout period, it will issue a microcontroller reset. The WDT is reset by executing the WDR (watchdog timer reset) instruction from the application code. The window mode makes it possible to define a time slot or window inside the total timeout period during which WDT must be reset. If the WDT is reset outside this window, either too early or too late, a system reset will be issued. Compared to the normal mode, this can also catch situations where a code error causes constant WDR execution. The WDT will run in active mode and all sleep modes, if enabled. It is asynchronous, runs from a CPU-independent clock source, and will continue to operate to issue a system reset even if the main clocks fail. The configuration change protection mechanism ensures that the WDT settings cannot be changed by accident. For increased safety, a fuse for locking the WDT settings is also available. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 26 14. Interrupts and Programmable Multilevel Interrupt Controller 14.1 Features Short and predictable interrupt response time Separate interrupt configuration and vector address for each interrupt Programmable multilevel interrupt controller Interrupt prioritizing according to level and vector address Three selectable interrupt levels for all interrupts: low, medium and high Selectable, round-robin priority scheme within low-level interrupts Non-maskable interrupts for critical functions Interrupt vectors optionally placed in the application section or the boot loader section 14.2 Overview Interrupts signal a change of state in peripherals, and this can be used to alter program execution. Peripherals can have one or more interrupts, and all are individually enabled and configured. When an interrupt is enabled and configured, it will generate an interrupt request when the interrupt condition is present. The programmable multilevel interrupt controller (PMIC) controls the handling and prioritizing of interrupt requests. When an interrupt request is acknowledged by the PMIC, the program counter is set to point to the interrupt vector, and the interrupt handler can be executed. All peripherals can select between three different priority levels for their interrupts: low, medium, and high. Interrupts are prioritized according to their level and their interrupt vector address. Medium-level interrupts will interrupt low-level interrupt handlers. High-level interrupts will interrupt both medium- and low-level interrupt handlers. Within each level, the interrupt priority is decided from the interrupt vector address, where the lowest interrupt vector address has the highest interrupt priority. Low-level interrupts have an optional round-robin scheduling scheme to ensure that all interrupts are serviced within a certain amount of time. Non-maskable interrupts (NMI) are also supported, and can be used for system critical functions. 14.3 Interrupt vectors The interrupt vector is the sum of the peripheral's base interrupt address and the offset address for specific interrupts in each peripheral. The base addresses for the Atmel AVR XMEGA A1U devices are shown in Table 14-1 on page 27. Offset addresses for each interrupt available in the peripheral are described for each peripheral in the XMEGA AU manual. For peripherals or modules that have only one interrupt, the interrupt vector is shown in Table 14-1 on page 27. The program address is the word address. Table 14-1. Reset and interrupt vectors. Program address (base address) Source 0x000 RESET 0x002 OSCF_INT_vect Crystal oscillator failure interrupt vector (NMI) 0x004 PORTC_INT_base Port C interrupt base 0x008 PORTR_INT_base Port R interrupt base 0x00C DMA_INT_base DMA controller interrupt base 0x014 RTC_INT_base Real time counter interrupt base 0x018 TWIC_INT_base Two-Wire interface on port C interrupt base 0x01C TCC0_INT_base Timer/counter 0 on port C interrupt base Interrupt description XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 27 Program address (base address) Source Interrupt description 0x028 TCC1_INT_base Timer/counter 1 on port C interrupt base 0x030 SPIC_INT_vect SPI on port C interrupt vector 0x032 USARTC0_INT_base USART 0 on port C interrupt base 0x038 USARTC1_INT_base USART 1 on port C interrupt base 0x03E AES_INT_vect AES interrupt vector 0x040 NVM_INT_base Nonvolatile memory interrupt base 0x044 PORTB_INT_base Port B interrupt base 0x048 ACB_INT_base Analog comparator on port B interrupt base 0x04E ADCB_INT_base Analog to digital converter on port B interrupt base 0x056 PORTE_INT_base Port E interrupt base 0x05A TWIE_INT_base Two-Wire interface on port E interrupt base 0x05E TCE0_INT_base Timer/counter 0 on port E interrupt base 0x06A TCE1_INT_base Timer/counter 1 on port E interrupt base 0x072 SPIE_INT_vect SPI on port E interrupt vector 0x074 USARTE0_INT_base USART 0 on port E interrupt base 0x07A USARTE1_INT_base USART 1 on port E interrupt base 0x080 PORTD_INT_base Port D interrupt base 0x084 PORTA_INT_base Port A interrupt base 0x088 ACA_INT_base Analog comparator on Port A interrupt base 0x08E ADCA_INT_base Analog to digital converter on Port A interrupt base 0x096 TWID_INT_base Two-Wire Interface on port D interrupt base 0x09A TCD0_INT_base Timer/counter 0 on port D interrupt base 0x0A6 TCD1_INT_base Timer/counter 1 on port D interrupt base 0x0AE SPID_INT_vector SPI on port D interrupt vector 0x0B0 USARTD0_INT_base USART 0 on port D interrupt base 0x0B6 USARTD1_INT_base USART 1 on port D interrupt base 0x0BC PORTQ_INT_base Port Q INT base 0x0C0 PORTH_INT_base Port H INT base 0x0C4 PORTJ_INT_base Port J INT base 0x0C8 PORTK_INT_base Port K INT base 0x0D0 PORTF_INT_base Port F INT base 0x0D4 TWIF_INT_base Two-Wire interface on Port F INT base 0x0D8 TCF0_INT_base Timer/counter 0 on port F interrupt base XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 28 Program address (base address) Source Interrupt description 0x0E4 TCF1_INT_base Timer/counter 1 on port F interrupt base 0x0EC SPIF_INT_vector SPI ion port F interrupt base 0x0EE USARTF0_INT_base USART 0 on port F interrupt base 0x0F4 USARTF1_INT_base USART 1 on port F interrupt base 0x0FA USB_INT_base USB on port D interrupt base XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 29 15. I/O Ports 15.1 Features 78 General purpose input and output pins with individual configuration Output driver with configurable driver and pull settings: Totem-pole Wired-AND Wired-OR Bus-keeper Inverted I/O Input with synchronous and/or asynchronous sensing with interrupts and events Sense both edges Sense rising edges Sense falling edges Sense low level Optional pull-up and pull-down resistor on input and Wired-OR/AND configurations Optional slew rate control Asynchronous pin change sensing that can wake the device from all sleep modes Two port interrupts with pin masking per I/O port Efficient and safe access to port pins Hardware read-modify-write through dedicated toggle/clear/set registers Configuration of multiple pins in a single operation Mapping of port registers into bit-accessible I/O memory space Peripheral clocks output on port pin Real-time counter clock output to port pin Event channels can be output on port pin Remapping of digital peripheral pin functions 15.2 Selectable USART, SPI, and timer/counter input/output pin locations Overview One port consists of up to eight port pins: pin 0 to 7. Each port pin can be configured as input or output with configurable driver and pull settings. They also implement synchronous and asynchronous input sensing with interrupts and events for selectable pin change conditions. Asynchronous pin-change sensing means that a pin change can wake the device from all sleep modes, included the modes where no clocks are running. All functions are individual and configurable per pin, but several pins can be configured in a single operation. The pins have hardware read-modify-write (RMW) functionality for safe and correct change of drive value and/or pull resistor configuration. The direction of one port pin can be changed without unintentionally changing the direction of any other pin. The port pin configuration also controls input and output selection of other device functions. It is possible to have both the peripheral clock and the real-time clock output to a port pin, and available for external use. The same applies to events from the event system that can be used to synchronize and control external functions. Other digital peripherals, such as USART, SPI, and timer/counters, can be remapped to selectable pin locations in order to optimize pin-out versus application needs. The notation of these ports are PORTA, PORTB, PORTC, PORTD, PORTE, PORTF, PORTH, PORTJ, PORTK, PORTQ and PORTR. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 30 15.3 Output Driver All port pins (Pn) have programmable output configuration. The port pins also have configurable slew rate limitation to reduce electromagnetic emission. 15.3.1 Push-pull Figure 15-1. I/O configuration - Totem-pole. DIRn OUTn Pn INn 15.3.2 Pull-down Figure 15-2. I/O configuration - Totem-pole with pull-down (on input). DIRn OUTn Pn INn 15.3.3 Pull-up Figure 15-3. I/O configuration - Totem-pole with pull-up (on input). DIRn OUTn Pn INn XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 31 15.3.4 Bus-keeper The bus-keeper's weak output produces the same logical level as the last output level. It acts as a pull-up if the last level was `1', and pull-down if the last level was `0'. Figure 15-4. I/O configuration - Totem-pole with bus-keeper. DIRn OUTn Pn INn 15.3.5 Others Figure 15-5. Output configuration - Wired-OR with optional pull-down. OUTn Pn INn Figure 15-6. I/O configuration - Wired-AND with optional pull-up. INn Pn OUTn XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 32 15.4 Input sensing Input sensing is synchronous or asynchronous depending on the enabled clock for the ports, and the configuration is shown in Figure 15-7 on page 33. Figure 15-7. Input sensing system overview Asynchronous sensing EDGE DETECT Interrupt Control IRQ Synchronous sensing Pxn Synchronizer INn D Q D R Q EDGE DETECT Synchronous Events R INVERTED I/O Asynchronous Events When a pin is configured with inverted I/O, the pin value is inverted before the input sensing. 15.5 Alternate Port Functions Most port pins have alternate pin functions in addition to being a general purpose I/O pin. When an alternate function is enabled, it might override the normal port pin function or pin value. This happens when other peripherals that require pins are enabled or configured to use pins. If and how a peripheral will override and use pins is described in the section for that peripheral. "Pinout and Pin Functions" on page 56 shows which modules on peripherals that enable alternate functions on a pin, and what alternate functions that are available on a pin. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 33 16. TC0/1 - 16-bit Timer/Counter Type 0 and 1 16.1 Features Eight 16-bit timer/counters Four timer/counters of type 0 Four timer/counters of type 1 32-bit timer/counter support by cascading two timer/counters Up to four compare or capture (CC) channels Four CC channels for timer/counters of type 0 Two CC channels for timer/counters of type 1 Double buffered timer period setting Double buffered capture or compare channels Waveform generation: Frequency generation Single-slope pulse width modulation Dual-slope pulse width modulation Input capture: Input capture with noise cancelling Frequency capture Pulse width capture 32-bit input capture Timer overflow and error interrupt events One compare match or input capture interrupt event per CC channel Can be used with event system for: Quadrature decoding Count and direction control Capture Can be used with DMA and trigger DMA transactions High-resolution extension Increases frequency and waveform resolution by 4x (2-bit) or 8x (3-bit) Advanced waveform extension 16.2 Low and high-side output with programmable dead-time insertion (DTI) Event controlled fault protection for safe disabling of external drivers Overview Atmel AVR XMEGA devices have a set of eight flexible 16-bit timer/counters (TC). Their capabilities include accurate program execution timing, frequency and waveform generation, and input capture with time and frequency measurement of digital signals. Two timer/counters can be cascaded to create a 32-bit timer/counter with optional 32-bit capture. A timer/counter consists of a base counter and a set of compare or capture (CC) channels. The base counter can be used to count clock cycles or events. It has direction control and period setting that can be used for timing. The CC channels can be used together with the base counter to do compare match control, frequency generation, and pulse width waveform modulation, as well as various input capture operations. A timer/counter can be configured for either capture or compare functions, but cannot perform both at the same time. A timer/counter can be clocked and timed from the peripheral clock with optional prescaling or from the event system. The event system can also be used for direction control and capture trigger or to synchronize operations. There are two differences between timer/counter type 0 and type 1. Timer/counter 0 has four CC channels, and timer/counter 1 has two CC channels. All information related to CC channels 3 and 4 is valid only for timer/counter 0. Only Timer/Counter 0 has the split mode feature that split it into 2 8-bit Timer/Counters with four compare channels each. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 34 Some timer/counters have extensions to enable more specialized waveform and frequency generation. The advanced waveform extension (AWeX) is intended for motor control and other power control applications. It enables low- and highside output with dead-time insertion, as well as fault protection for disabling and shutting down external drivers. It can also generate a synchronized bit pattern across the port pins. The advanced waveform extension can be enabled to provide extra and more advanced features for the Timer/Counter. This is only available for Timer/Counter 0. See ""AWeX - Advanced Waveform Extension" on page 37 for more details. The high-resolution (hi-res) extension can be used to increase the waveform output resolution by four or eight times by using an internal clock source running up to four times faster than the peripheral clock. See "Hi-Res - High Resolution Extension" on page 38 for more details. Figure 16-1. Overview of a timer/counter (TC) and closely related peripherals. Timer/Counter Base Counter Prescaler clkPER Timer Period Control Logic Counter Event System clkPER4 Buffer Capture Control Waveform Generation Dead-Time Insertion Pattern Generation Fault Protection PORT Comparator AWeX Hi-Res Compare/Capture Channel D Compare/Capture Channel C Compare/Capture Channel B Compare/Capture Channel A PORTC, PORTD, PORTE and PORTF each has one timer/counter 0 and one timer/counter1. Notation of these timer/counters are TCC0 (timer/counter C0), TCC1, TCD0, TCD1, TCE0, TCE1, TCF0, and TCF1, respectively. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 35 17. TC2 - Time/Counter Type 2 17.1 Features Eight eight-bit timer/counters Four Low-byte timer/counters Four High-byte timer/counters Up to eight compare channels in each timer/counter 2 Four compare channels for the low-byte timer/counter Four compare channels for the high-byte timer/counter Waveform generation Single slope pulse width modulation Timer underflow interrupts/events One compare match interrupt/event per compare channel for the low-byte timer/counter Can be used with the event system for count control Can be used to trigger DMA transactions 17.2 Overview There are four Timer/counter 2. These are realized when a Timer/counter 0 is set in split mode. It is then a system of two eight-bit timer/counters, each with four compare channels. This results in eight configurable pulse width modulation (PWM) channels with individually controlled duty cycles, and is intended for applications that require a high number of PWM channels. The two eight-bit timer/counters in this system are referred to as the low-byte timer/counter and high-byte timer/counter, respectively. The difference between them is that only the low-byte timer/counter can be used to generate compare match interrupts, events and DMA triggers. The two eight-bit timer/counters have a shared clock source and separate period and compare settings. They can be clocked and timed from the peripheral clock, with optional prescaling, or from the event system. The counters are always counting down. PORTC, PORTD, PORTE and PORTF each has one Timer/Counter 2. Notation of these are TCC2 (Time/Counter C2), TCD2, TCE2 and TCF2, respectively. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 36 18. AWeX - Advanced Waveform Extension 18.1 Features Waveform output with complementary output from each compare channel Four dead-time insertion (DTI) units 8-bit resolution Separate high and low side dead-time setting Double buffered dead time Optionally halts timer during dead-time insertion Pattern generation unit creating synchronised bit pattern across the port pins Double buffered pattern generation Optional distribution of one compare channel output across the port pins Event controlled fault protection for instant and predictable fault triggering 18.2 Overview The advanced waveform extension (AWeX) provides extra functions to the timer/counter in waveform generation (WG) modes. It is primarily intended for use with different types of motor control and other power control applications. It enables low- and high side output with dead-time insertion and fault protection for disabling and shutting down external drivers. It can also generate a synchronized bit pattern across the port pins. Each of the waveform generator outputs from the Timer/Counter 0 are split into a complimentary pair of outputs when any AWeX features are enabled. These output pairs go through a dead-time insertion (DTI) unit that generates the noninverted low side (LS) and inverted high side (HS) of the WG output with dead-time insertion between LS and HS switching. The DTI output will override the normal port value according to the port override setting. The pattern generation unit can be used to generate a synchronized bit pattern on the port it is connected to. In addition, the WG output from compare channel A can be distributed to and override all the port pins. When the pattern generator unit is enabled, the DTI unit is bypassed. The fault protection unit is connected to the event system, enabling any event to trigger a fault condition that will disable the AWeX output. The event system ensures predictable and instant fault reaction, and gives great flexibility in the selection of fault triggers. The AWeX is available for TCC0 and TCE0. The notation of these are AWEXC and AWEXE. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 37 19. Hi-Res - High Resolution Extension 19.1 Features Increases waveform generator resolution up to 8x (three bits) Supports frequency, single-slope PWM and dual-slope PWM generation Supports the AWeX when this is used for the same timer/counter 19.2 Overview The high-resolution (hi-res) extension can be used to increase the resolution of the waveform generation output from a timer/counter by four or eight. It can be used for a timer/counter doing frequency, single-slope PWM, or dual-slope PWM generation. It can also be used with the AWeX if this is used for the same timer/counter. The hi-res extension uses the peripheral 4x clock (ClkPER4). The system clock prescalers must be configured so the peripheral 4x clock frequency is four times higher than the peripheral and CPU clock frequency when the hi-res extension is enabled. There are four hi-res extensions that each can be enabled for each timer/counters pair on PORTC, PORTD, PORTE and PORTF. The notation of these peripherals are HIRESC, HIRESD, HIRESE and HIRESF, respectively. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 38 20. RTC - 16-bit Real-Time Counter 20.1 Features 16-bit resolution Selectable clock source 32.768kHz external crystal External clock 32.768kHz internal oscillator 32kHz internal ULP oscillator Programmable 10-bit clock prescaling One compare register One period register Clear counter on period overflow Optional interrupt/event on overflow and compare match 20.2 Overview The 16-bit real-time counter (RTC) is a counter that typically runs continuously, including in low-power sleep modes, to keep track of time. It can wake up the device from sleep modes and/or interrupt the device at regular intervals. The reference clock is typically the 1.024kHz output from a high-accuracy crystal of 32.768kHz, and this is the configuration most optimized for low power consumption. The faster 32.768kHz output can be selected if the RTC needs a resolution higher than 1ms. The RTC can also be clocked from an external clock signal, the 32.768kHz internal oscillator or the 32kHz internal ULP oscillator. The RTC includes a 10-bit programmable prescaler that can scale down the reference clock before it reaches the counter. A wide range of resolutions and time-out periods can be configured. With a 32.768kHz clock source, the maximum resolution is 30.5s, and time-out periods can range up to 2000 seconds. With a resolution of 1s, the maximum timeout period is more than18 hours (65536 seconds). The RTC can give a compare interrupt and/or event when the counter equals the compare register value, and an overflow interrupt and/or event when it equals the period register value. Figure 20-1. Real-time counter overview. External Clock TOSC1 TOSC2 32.768kHz Crystal Osc 32.768kHz Int. Osc DIV32 DIV32 32kHz int ULP (DIV32) PER RTCSRC clkRTC 10-bit prescaler = TOP/ Overflow = "match"/ Compare CNT COMP XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 39 21. USB - Universal Serial Bus Interface 21.1 Features One USB 2.0 full speed (12Mbps) and low speed (1.5Mbps) device compliant interface Integrated on-chip USB transceiver, no external components needed 16 endpoint addresses with full endpoint flexibility for up to 31 endpoints One input endpoint per endpoint address One output endpoint per endpoint address Endpoint address transfer type selectable to Control transfers Interrupt transfers Bulk transfers Isochronous transfers Configurable data payload size per endpoint, up to 1023 bytes Endpoint configuration and data buffers located in internal SRAM Configurable location for endpoint configuration data Configurable location for each endpoint's data buffer Built-in direct memory access (DMA) to internal SRAM for: Endpoint configurations Reading and writing endpoint data Ping-pong operation for higher throughput and double buffered operation Input and output endpoint data buffers used in a single direction CPU/DMA controller can update data buffer during transfer Multi packet transfer for reduced interrupt load and software intervention Data payload exceeding maximum packet size is transferred in one continuous transfer No interrupts or software interaction on packet transaction level Transaction complete FIFO for workflow management when using multiple endpoints Tracks all completed transactions in a first-come, first-served work queue Clock selection independent of system clock source and selection Minimum 1.5MHz CPU clock required for low speed USB operation Minimum 12MHz CPU clock required for full speed operation Connection to event system On chip debug possibilities during USB transactions 21.2 Overview The USB module is a USB 2.0 full speed (12Mbps) and low speed (1.5Mbps) device compliant interface. The USB supports 16 endpoint addresses. All endpoint addresses have one input and one output endpoint, for a total of 31 configurable endpoints and one control endpoint. Each endpoint address is fully configurable and can be configured for any of the four transfer types; control, interrupt, bulk, or isochronous. The data payload size is also selectable, and it supports data payloads up to 1023 bytes. No dedicated memory is allocated for or included in the USB module. Internal SRAM is used to keep the configuration for each endpoint address and the data buffer for each endpoint. The memory locations used for endpoint configurations and data buffers are fully configurable. The amount of memory allocated is fully dynamic, according to the number of endpoints in use and the configuration of these. The USB module has built-in direct memory access (DMA), and will read/write data from/to the SRAM when a USB transaction takes place. To maximize throughput, an endpoint address can be configured for ping-pong operation. When done, the input and output endpoints are both used in the same direction. The CPU or DMA controller can then read/write one data buffer while the USB module writes/reads the others, and vice versa. This gives double buffered communication. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 40 Multipacket transfer enables a data payload exceeding the maximum packet size of an endpoint to be transferred as multiple packets without software intervention. This reduces the CPU intervention and the interrupts needed for USB transfers. For low-power operation, the USB module can put the microcontroller into any sleep mode when the USB bus is idle and a suspend condition is given. Upon bus resumes, the USB module can wake up the microcontroller from any sleep mode. PORTD has one USB. Notation of this is USB. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 41 22. TWI - Two-Wire Interface 22.1 Features Four identical two-wire interface peripherals Bidirectional two-wire communication interface Phillips I2C compatible System Management Bus (SMBus) compatible Bus master and slave operation supported Slave operation Single bus master operation Bus master in multi-master bus environment Multi-master arbitration Flexible slave address match functions 7-bit and general call address recognition in hardware 10-bit addressing supported Address mask register for dual address match or address range masking Optional software address recognition for unlimited number of addresses Slave can operate in all sleep modes, including power-down Slave address match can wake device from all sleep modes, including power-down 100kHz and 400kHz bus frequency support Slew-rate limited output drivers Input filter for bus noise and spike suppression Support arbitration between start repeated start and data bit (SMBus) Slave arbitration allows support for address resolve protocol (ARP) (SMBus) 22.2 Overview The two-wire interface (TWI) is a bidirectional, two-wire communication interface. It is I2C and System Management Bus (SMBus) compatible. The only external hardware needed to implement the bus is one pull-up resistor on each bus line. A device connected to the bus must act as a master or a slave. The master initiates a data transaction by addressing a slave on the bus and telling whether it wants to transmit or receive data. One bus can have many slaves and one or several masters that can take control of the bus. An arbitration process handles priority if more than one master tries to transmit data at the same time. Mechanisms for resolving bus contention are inherent in the protocol. The TWI module supports master and slave functionality. The master and slave functionality are separated from each other, and can be enabled and configured separately. The master module supports multi-master bus operation and arbitration. It contains the baud rate generator. Both 100kHz and 400kHz bus frequencies are supported. Quick command and smart mode can be enabled to auto-trigger operations and reduce software complexity. The slave module implements 7-bit address match and general address call recognition in hardware. 10-bit addressing is also supported. A dedicated address mask register can act as a second address match register or as a register for address range masking. The slave continues to operate in all sleep modes, including power-down mode. This enables the slave to wake up the device from all sleep modes on TWI address match. It is possible to disable the address matching to let this be handled in software instead. The TWI module will detect START and STOP conditions, bus collisions, and bus errors. Arbitration lost, errors, collision, and clock hold on the bus are also detected and indicated in separate status flags available in both master and slave modes. It is possible to disable the TWI drivers in the device, and enable a four-wire digital interface for connecting to an external TWI bus driver. This can be used for applications where the device operates from a different VCC voltage than used by the TWI bus. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 42 PORTC, PORTD, PORTE, and PORTF each has one TWI. Notation of these peripherals are TWIC, TWID, TWIE, and TWIF. 23. SPI - Serial Peripheral Interface 23.1 Features Four identical SPI peripherals Full-duplex, three-wire synchronous data transfer Master or slave operation Lsb first or msb first data transfer Eight programmable bit rates Interrupt flag at the end of transmission Write collision flag to indicate data collision Wake up from idle sleep mode Double speed master mode 23.2 Overview The Serial Peripheral Interface (SPI) is a high-speed synchronous data transfer interface using three or four pins. It allows fast communication between an Atmel AVR XMEGA device and peripheral devices or between several microcontrollers. The SPI supports full-duplex communication. A device connected to the bus must act as a master or slave. The master initiates and controls all data transactions. PORTC, PORTD, PORTE, and PORTF each has one SPI. Notation of these peripherals are SPIC, SPID, SPIE, and SPIF. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 43 24. USART 24.1 Features Eight identical USART peripherals Full-duplex operation Asynchronous or synchronous operation Synchronous02 clock rates up to 1/2 of the device clock frequency Asynchronous clock rates up to 1/8 of the device clock frequency Supports serial frames with 5, 6, 7, 8, or 9 data bits and 1 or 2 stop bits Fractional baud rate generator Can generate desired baud rate from any system clock frequency No need for external oscillator with certain frequencies Built-in error detection and correction schemes Odd or even parity generation and parity check Data overrun and framing error detection Noise filtering includes false start bit detection and digital low-pass filter Separate interrupts for Transmit complete Transmit data register empty Receive complete Multiprocessor communication mode Addressing scheme to address a specific devices on a multi device bus Enable unaddressed devices to automatically ignore all frames Master SPI mode Double buffered operation Operation up to 1/2 of the peripheral clock frequency IRCOM module for IrDA compliant pulse modulation/demodulation 24.2 Overview The universal synchronous and asynchronous serial receiver and transmitter (USART) is a fast and flexible serial communication module. The USART supports full-duplex communication and asynchronous and synchronous operation. The USART can be configured to operate in SPI master mode and used for SPI communication. Communication is frame based, and the frame format can be customized to support a wide range of standards. The USART is buffered in both directions, enabling continued data transmission without any delay between frames. Separate interrupts for receive and transmit complete enable fully interrupt driven communication. Frame error and buffer overflow are detected in hardware and indicated with separate status flags. Even or odd parity generation and parity check can also be enabled. The clock generator includes a fractional baud rate generator that is able to generate a wide range of USART baud rates from any system clock frequencies. This removes the need to use an external crystal oscillator with a specific frequency to achieve a required baud rate. It also supports external clock input in synchronous slave operation. When the USART is set in master SPI mode, all USART-specific logic is disabled, leaving the transmit and receive buffers, shift registers, and baud rate generator enabled. Pin control and interrupt generation are identical in both modes. The registers are used in both modes, but their functionality differs for some control settings. An IRCOM module can be enabled for one USART to support IrDA 1.4 physical compliant pulse modulation and demodulation for baud rates up to 115.2Kbps. PORTC, PORTD, PORTE, and PORTF each has two USARTs. Notation of these peripherals are USARTC0, USARTC1, USARTD0, USARTD1, USARTE0, USARTE1, USARTF0 and USARTF1. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 44 25. IRCOM - IR Communication Module 25.1 Features Pulse modulation/demodulation for infrared communication IrDA compatible for baud rates up to 115.2Kbps Selectable pulse modulation scheme 3/16 of the baud rate period Fixed pulse period, 8-bit programmable Pulse modulation disabled Built-in filtering Can be connected to and used by any USART 25.2 Overview Atmel AVR XMEGA devices contain an infrared communication module (IRCOM) that is IrDA compatible for baud rates up to 115.2Kbps. It can be connected to any USART to enable infrared pulse encoding/decoding for that USART. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 45 26. AES and DES Crypto Engine 26.1 Features Data Encryption Standard (DES) CPU instruction Advanced Encryption Standard (AES) crypto module DES Instruction Encryption and decryption DES supported Encryption/decryption in 16 CPU clock cycles per 8-byte block AES crypto module Encryption and decryption Supports 128-bit keys Supports XOR data load mode to the state memory Encryption/decryption in 375 clock cycles per 16-byte block 26.2 Overview The Advanced Encryption Standard (AES) and Data Encryption Standard (DES) are two commonly used standards for cryptography. These are supported through an AES peripheral module and a DES CPU instruction, and the communication interfaces and the CPU can use these for fast, encrypted communication and secure data storage. DES is supported by an instruction in the AVR CPU. The 8-byte key and 8-byte data blocks must be loaded into the register file, and then the DES instruction must be executed 16 times to encrypt/decrypt the data block. The AES crypto module encrypts and decrypts 128-bit data blocks with the use of a 128-bit key. The key and data must be loaded into the key and state memory in the module before encryption/decryption is started. It takes 375 peripheral clock cycles before the encryption/decryption is done. The encrypted/encrypted data can then be read out, and an optional interrupt can be generated. The AES crypto module also has DMA support with transfer triggers when encryption/decryption is done and optional auto-start of encryption/decryption when the state memory is fully loaded. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 46 27. CRC - Cyclic Redundancy Check Generator 27.1 Features Cyclic redundancy check (CRC) generation and checking for Communication data Program or data in flash memory Data in SRAM and I/O memory space Integrated with flash memory, DMA controller and CPU Continuous CRC on data going through a DMA channel Automatic CRC of the complete or a selectable range of the flash memory CPU can load data to the CRC generator through the I/O interface CRC polynomial software selectable to CRC-16 (CRC-CCITT) CRC-32 (IEEE 802.3) Zero remainder detection 27.2 Overview A cyclic redundancy check (CRC) is an error detection technique test algorithm used to find accidental errors in data, and it is commonly used to determine the correctness of a data transmission, and data present in the data and program memories. A CRC takes a data stream or a block of data as input and generates a 16- or 32-bit output that can be appended to the data and used as a checksum. When the same data are later received or read, the device or application repeats the calculation. If the new CRC result does not match the one calculated earlier, the block contains a data error. The application will then detect this and may take a corrective action, such as requesting the data to be sent again or simply not using the incorrect data. Typically, an n-bit CRC applied to a data block of arbitrary length will detect any single error burst not longer than n bits (any single alteration that spans no more than n bits of the data), and will detect the fraction 1-2-n of all longer error bursts. The CRC module in Atmel AVR XMEGA devices supports two commonly used CRC polynomials; CRC-16 (CRCCCITT) and CRC-32 (IEEE 802.3). CRC-16: Polynomial: x16+x12+x5+1 Hex value: 0x1021 CRC-32: Polynomial: x32+x26+x23+x22+x16+x12+x11+x10+x8+x7+x5+x4+x2+x+1 Hex value: 0x04C11DB7 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 47 28. EBI - External Bus Interface 28.1 Features Supports SRAM up to: 512KB using 2- or 3-port EBI configuration 16MB using 3- or 4-port EBI configuration Supports SDRAM up to: 128Mb using 3- or 4-port EBI configuration 4-bit SDRAM with 3-port EBI configuration 4- or 8-bit SDRAM with 4-port EBI configuration Four software configurable chip selects Software configurable wait state insertion Can run from the 2x peripheral clock frequency for fast access Simultaneous SRAM and SDRAM support with 4-port EBI configuration 28.2 Overview The External Bus Interface (EBI) is used to connect external peripherals and memory for accessthrough the data memory space. When the EBI is enabled, data address space outside the internal SRAM becomes available using dedicated EBI pins. The EBI can interface external SRAM, SDRAM, and peripherals, such as LCD displays and other memory mapped devices. The address space for the external memory is selectable from 256 bytes (8-bit) up to 16MB (24-bit). Various multiplexing modes for address and data lines can be selected for optimal use of pins when more or fewer pins are available for the EBI. The complete memory will be mapped into one linear data address space continuing from the end of the internal SRAM. The EBI has four chip selects, each with separate configuration. Each can be configured for SRAM, SRAM low pin count (LPC), or SDRAM. The EBI is clocked from the fast, 2x peripheral clock, running up to two times faster than the CPU. Four-bit and eight-bit SDRAM are supported, and SDRAM configurations, such as CAS latency and refresh rate, are configurable in software. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 48 29. ADC - 12-bit Analog to Digital Converter 29.1 Features Two Analog to Digital Converters 12-bit resolution Up to two million samples per second Two inputs can be sampled simultaneously using ADC and 1x gain stage Four inputs can be sampled within 1.5s Down to 2.5s conversion time with 8-bit resolution Down to 3.5s conversion time with 12-bit resolution Differential and single-ended input Up to 16 single-ended inputs 16x4 differential inputs without gain 8x4 differential input with gain Built-in differential gain stage 1/2x, 1x, 2x, 4x, 8x, 16x, 32x, and 64x gain options Single, continuous and scan conversion options Four internal inputs Internal temperature sensor DAC output VCC voltage divided by 10 1.1V bandgap voltage Four conversion channels with individual input control and result registers Enable four parallel configurations and results Internal and external reference options Compare function for accurate monitoring of user defined thresholds Optional event triggered conversion for accurate timing Optional DMA transfer of conversion results Optional interrupt/event on compare result 29.2 Overview The ADC converts analog signals to digital values. There are two Analog to Digital Converters (ADCs) modules that can be operated simultaneously, individually or synchronized. The ADC has 12-bit resolution and is capable of converting up to two million samples per second (msps). The input selection is flexible, and both single-ended and differential measurements can be done. For differential measurements, an optional gain stage is available to increase the dynamic range. In addition, several internal signal inputs are available. The ADC can provide both signed and unsigned results. This is a pipelined ADC that consists of several consecutive stages. The pipelined design allows a high sample rate at a low system clock frequency. It also means that a new input can be sampled and a new ADC conversion started while other ADC conversions are still ongoing. This removes dependencies between sample rate and propagation delay. The ADC has four conversion channels (0-3) with individual input selection, result registers, and conversion start control. The ADC can then keep and use four parallel configurations and results, and this will ease use for applications with high data throughput or for multiple modules using the ADC independently. It is possible to use DMA to move ADC results directly to memory or peripherals when conversions are done. Both internal and external reference voltages can be used. An integrated temperature sensor is available for use with the ADC. The output from the DAC, VCC/10 and the bandgap voltage can also be measured by the ADC. The ADC has a compare function for accurate monitoring of user defined thresholds with minimum software intervention required. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 49 Figure 29-1. ADC overview. ADC0 Compare * ** ADC15 ADC0 Internal signals VINP CH0 Result ** * ADC7 ADC4 CH1 Result Threshold (Int Req) 1/2x - 64x CH2 Result * ** ADC7 Int. signals < > Internal signals CH3 Result VINN ADC0 * ** ADC3 Int. signals Internal 1.00V Internal VCC/1.6V Internal VCC/2 AREFA AREFB Reference Voltage Two inputs can be sampled simultaneously as both the ADC and the gain stage include sample and hold circuits, and the gain stage has 1x gain setting. Four inputs can be sampled within 1.5s without any intervention by the application. The ADC may be configured for 8- or 12-bit result, reducing the minimum conversion time (propagation delay) from 3.5s for 12-bit to 2.5s for 8-bit result. ADC conversion results are provided left- or right adjusted with optional `1' or `0' padding. This eases calculation when the result is represented as a signed integer (signed 16-bit number). PORTA and PORTB each has one ADC. Notation of these peripherals are ADCA and ADCB, respectively. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 50 30. DAC - 12-bit Digital to Analog Converter 30.1 Features Two digital to analog converters (DACs) 12-bit resolution Two independent, continuous-drive output channels Up to one million samples per second conversion rate per DAC channel Built-in calibration that removes: Offset error Gain error Multiple conversion trigger sources On new available data Events from the event system High drive capabilities and support for Resistive loads Capacitive loads Combined resistive and capacitive loads Internal and external reference options DAC output available as input to analog comparator and ADC Low-power mode, with reduced drive strength Optional DMA transfer of data 30.2 Overview The digital-to-analog converter (DAC) converts digital values to voltages. The DAC has two channels, each with12-bit resolution, and is capable of converting up to one million samples per second (msps) on each channel. The built-in calibration system can remove offset and gain error when loaded with calibration values from software. Figure 30-1. DAC overview. DMA req (Data Empty) CH0DATA 12 D A T A Trigger AVCC Internal 1.00V AREFA AREFB Reference selection Output Driver Select CTRLB Enable Int. driver To AC/ADC CTRLA Internal Output enable Trigger CH1DATA 12 D A T A Select Enable Output Driver DMA req (Data Empty) XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 51 A DAC conversion is automatically started when new data to be converted are available. Events from the event system can also be used to trigger a conversion, and this enables synchronized and timed conversions between the DAC and other peripherals, such as a timer/counter. The DMA controller can be used to transfer data to the DAC. The DAC has high drive strength, and is capable of driving both resistive and capacitive loads, aswell as loads which combine both. A low-power mode is available, which will reduce the drive strength of the output. Internal and external voltage references can be used. The DAC output is also internally available for use as input to the analog comparator or ADC. PORTA and PORTB each has one DAC. Notation of these peripherals are DACA and DACB, respectively. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 52 31. AC - Analog Comparator 31.1 Features Four Analog Comparators Selectable propagation delay versus current consumption Selectable hysteresis No Small Large Analog comparator output available on pin Flexible input selection All pins on the port Output from the DAC Bandgap reference voltage A 64-level programmable voltage scaler of the internal VCC voltage Interrupt and event generation on: Rising edge Falling edge Toggle Window function interrupt and event generation on: Signal above window Signal inside window Signal below window Constant current source with configurable output pin selection 31.2 Overview The analog comparator (AC) compares the voltage levels on two inputs and gives a digital output based on this comparison. The analog comparator may be configured to generate interrupt requests and/or events upon several different combinations of input change. Two important properties of the analog comparator's dynamic behavior are: hysteresis and propagation delay. Both of these parameters may be adjusted in order to achieve the optimal operation for each application. The input selection includes analog port pins, several internal signals, and a 64-level programmable voltage scaler. The analog comparator output state can also be output on a pin for use by external devices. A constant current source can be enabled and output on a selectable pin. This can be used to replace, for example, external resistors used to charge capacitors in capacitive touch sensing applications. The analog comparators are always grouped in pairs on each port. These are called analog comparator 0 (AC0) and analog comparator 1 (AC1). They have identical behavior, but separate control registers. Used as pair, they can be set in window mode to compare a signal to a voltage range instead of a voltage level. PORTA and PORTB each has one AC pair. Notations are ACA and ACB, respectively. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 53 Figure 31-1. Analog comparator overview. Pin Input + AC0OUT Pin Input Hysteresis DAC Voltage Scaler Enable ACnMUXCTRL ACnCTRL Interrupt Mode WINCTRL Enable Bandgap Interrupt Sensititivity Control & Window Function Interrupts Events Hysteresis + Pin Input AC1OUT Pin Input The window function is realized by connecting the external inputs of the two analog comparators in a pair as shown in Figure 31-2. Figure 31-2. Analog comparator window function. + AC0 Upper limit of window Interrupt sensitivity control Input signal Interrupts Events + AC1 Lower limit of window - XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 54 32. PDI - Programming and Debugging 32.1 Features Programming External programming through PDI or JTAG interfaces Minimal protocol overhead for fast operation Built-in error detection and handling for reliable operation Boot loader support for programming through any communication interface Debugging Nonintrusive, real-time, on-chip debug system No software or hardware resources required from device except pin connection Program flow control Go, Stop, Reset, Step Into, Step Over, Step Out, Run-to-Cursor Unlimited number of user program breakpoints Unlimited number of user data breakpoints, break on: Data location read, write, or both read and write Data location content equal or not equal to a value Data location content is greater or smaller than a value Data location content is within or outside a range No limitation on device clock frequency Program and Debug Interface (PDI) Two-pin interface for external programming and debugging Uses the Reset pin and a dedicated pin No I/O pins required during programming or debugging JTAG interface 32.2 Four-pin, IEEE Std. 1149.1 compliant interface for programming and debugging Boundary scan capabilities according to IEEE Std. 1149.1 (JTAG) Overview The Program and Debug Interface (PDI) is an Atmel proprietary interface for external programming and on-chip debugging of a device. The PDI supports fast programming of nonvolatile memory (NVM) spaces; flash, EEPOM, fuses, lock bits, and the user signature row. Debug is supported through an on-chip debug system that offers nonintrusive, real-time debug. It does not require any software or hardware resources except for the device pin connection. Using the Atmel tool chain, it offers complete program flow control and support for an unlimited number of program and complex data breakpoints. Application debug can be done from a C or other high-level language source code level, as well as from an assembler and disassembler level. Programming and debugging can be done through two physical interfaces. The primary one is the PDI physical layer, which is available on all devices. This is a two-pin interface that uses the Reset pin for the clock input (PDI_CLK) and one other dedicated pin for data input and output (PDI_DATA). A JTAG interface is also available on most devices, and this can be used for programming and debugging through the four-pin JTAG interface. The JTAG interface is IEEE Std. 1149.1 compliant, and supports boundary scan. Any external programmer or on-chip debugger/emulator can be directly connected to either of these interfaces. Unless otherwise stated, all references to the PDI assume access through the PDI physical layer. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 55 33. Pinout and Pin Functions The device pinout is shown in "Pinout/Block Diagram" on page 3. In addition to general purpose I/O functionality, each pin can have several alternate functions. This will depend on which peripheral is enabled and connected to the actual pin. Only one of the pin functions can be used at time. 33.1 Alternate Pin Function Description The tables below show the notation for all pin functions available and describe its function. 33.1.1 Operation/ Power Supply VCC Digital supply voltage AVCC Analog supply voltage GND Ground 33.1.2 Port Interrupt functions SYNC Port pin with full synchronous and limited asynchronous interrupt function ASYNC Port pin with full synchronous and full asynchronous interrupt function 33.1.3 Analog functions ACn Analog Comparator input pin n ACnOUT Analog Comparator n Output ADCn Analog to Digital Converter input pin n DACn Digital to Analog Converter output pin n AREF Analog Reference input pin 33.1.4 External Bus Interface functions An Address line n Dn Data line n CSn Chip Select n ALEn Address Latch Enable pin n (SRAM) RE Read Enable (SRAM) WE External Data Memory Write (SRAM /SDRAM) BAn Bank Address (SDRAM) CAS Column Access Strobe (SDRAM) CKE SDRAM Clock Enable (SDRAM) CLK SDRAM Clock (SDRAM) DQM Data Mask Signal/Output Enable (SDRAM) RAS Row Access Strobe (SDRAM) XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 56 33.1.5 Timer/Counter and AWEX functions OCnxLS Output Compare Channel x Low Side for Timer/Counter n OCnxHS Output Compare Channel x High Side for Timer/Counter n 33.1.6 Communication functions SCL Serial Clock for TWI SDA Serial Data for TWI SCLIN Serial Clock In for TWI when external driver interface is enabled SCLOUT Serial Clock Out for TWI when external driver interface is enabled SDAIN Serial Data In for TWI when external driver interface is enabled SDAOUT Serial Data Out for TWI when external driver interface is enabled XCKn Transfer Clock for USART n RXDn Receiver Data for USART n TXDn Transmitter Data for USART n SS Slave Select for SPI MOSI Master Out Slave In for SPI MISO Master In Slave Out for SPI SCK Serial Clock for SPI D- Data- for USB D+ Data+ for USB 33.1.7 Oscillators, Clock and Event TOSCn Timer Oscillator pin n XTALn Input/Output for Oscillator pin n CLKOUT Peripheral Clock Output EVOUT Event Channel 0 Output 33.1.8 Debug/System functions RESET Reset pin PDI_CLK Program and Debug Interface Clock pin PDI_DATA Program and Debug Interface Data pin TCK JTAG Test Clock TDI JTAG Test Data In TDO JTAG Test Data Out TMS JTAG Test Mode Select XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 57 33.2 Alternate Pin Functions The tables below show the primary/default function for each pin on a port in the first column, the pin number in the second column, and then all alternate pin functions in the remaining columns. The head row shows what peripheral that enable and use the alternate pin functions. For better flexibility, some alternate functions also have selectable pin locations for their functions, this is noted under the the first table where this apply. Table 33-1. Port A - alternate functions. PORTA PIN # INTERRUPT ADCA POS /GAINPOS ADCB POS ADCA NEG ADCA ACA ACA ACA GAINNEG POS NEG OUT GND 93 AVCC 94 PA0 95 SYNC ADC0 ADC8 ADC0 AC0 AC0 PA1 96 SYNC ADC1 ADC9 ADC1 AC1 AC1 PA2 97 SYNC/ASYNC ADC2 ADC10 ADC2 AC2 PA3 98 SYNC ADC3 ADC11 ADC3 AC3 PA4 99 SYNC ADC4 ADC12 ADC4 AC4 PA5 100 SYNC ADC5 ADC13 ADC5 AC5 PA6 1 SYNC ADC6 ADC14 ADC6 AC6 PA7 2 SYNC ADC7 ADC15 ADC7 DACA REFA AREF DAC0 AC3 DAC1 AC5 AC1OUT AC7 AC0OUT Table 33-2. Port B - alternate functions. PORT B PIN# INTERRUPT ADCAPOS ADCBPOS/ GAINPOS ADCB NEG ADCB GAIN NEG ACB POS ACB NEG GND 3 AVCC 4 PB0 5 SYNC ADC8 ADC0 ADC0 AC0 AC0 PB1 6 SYNC ADC9 ADC1 ADC1 AC1 AC1 PB2 7 SYNC/ASYN C ADC10 ADC2 ADC2 AC2 PB3 8 SYNC ADC11 ADC3 ADC3 AC3 PB4 9 SYNC ADC12 ADC4 ADC4 AC4 PB5 10 SYNC ADC13 ADC5 ADC5 AC5 PB6 11 SYNC ADC14 ADC6 ADC6 AC6 PB7 12 SYNC ADC15 ADC7 ADC7 ACB OUT DACB REFB JTAG AREF DAC0 AC3 DAC1 TMS AC5 AC7 TDI AC1OUT TCK AC0OUT TDO XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 58 Table 33-3. Port C - alternate functions. PORT C PIN# INTERRUPT TCC0(1)(2) AWEXC TCC1 USARTC0(3) GND 13 VCC 14 PC0 15 SYNC OC0A OC0ALS PC1 16 SYNC OC0B OC0AHS XCK0 PC2 17 SYNC/ASYNC OC0C OC0BLS RXD0 PC3 18 SYNC OC0D OC0BHS TXD0 PC4 19 SYNC OC0CLS OC1A PC5 20 SYNC OC0CHS OC1B PC6 21 SYNC PC7 22 SYNC Notes: 1. 2. 3. 4. 5. 6. USARTC1 SPIC(4) TWIC CLOCKOUT(5) EVENTOUT(6) SDA SCL SS XCK1 MOSI OC0DLS RXD1 MISO clkRTC OC0DHS TXD1 SCK clkPER EVOUT Pin mapping of all TC0 can optionally be moved to high nibble of port. If TC0 is configured as TC2 all eight pins can be used for PWM output. Pin mapping of all USART0 can optionally be moved to high nibble of port. Pins MOSI and SCK for all SPI can optionally be swapped. CLKOUT can optionally be moved between port C, D and E and between pin 4 and 7. EVOUT can optionally be moved between port C, D and E and between pin 4 and 7. Table 33-4. Port D - alternate functions. PORT D PIN# INTERRUPT TCD0 TCD1 USBD USARTD0 GND 23 VCC 24 PD0 25 SYNC OC0A PD1 26 SYNC OC0B XCK0 PD2 27 SYNC/ASYN C OC0C RXD0 PD3 28 SYNC OC0D TXD0 PD4 29 SYNC OC1A PD5 30 SYNC OC1B PD6 31 SYNC PD7 32 SYNC USARTD1 SPID TWID CLOCKOUT EVENTOUT clkPER EVOUT SDA SCL SS XCK1 MOSI D- RXD1 MISO D+ TXD1 SCK USARTE1 SPIE Table 33-5. Port E - alternate functions. PORT E PIN # INTERRUPT TCE0 AWEXE TCE1 USARTE0 GND 33 VCC 34 PE0 35 SYNC OC0A OC0ALS PE1 36 SYNC OC0B OC0AHS XCK0 PE2 37 SYNC/ASYNC OC0C OC0BLS RXD0 TWIE CLOCKOUT EVENTOUT SDA SCL XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 59 PORT E PIN # INTERRUPT TCE0 AWEXE TCE1 PE3 38 SYNC OC0D OC0BHS PE4 39 SYNC OC0CLS OC1A PE5 40 SYNC OC0CHS OC1B PE6 41 SYNC PE7 42 SYNC USARTE0 USARTE1 SPIE TWIE CLOCKOUT EVENTOUT clkPER EVOUT TXD0 SS XCK1 MOSI OC0DLS RXD1 MISO OC0DHS TXD1 SCK Table 33-6. Port F - alternate functions. PORT F PIN # INTERRUPT TCF0 TCF1 USARTF0 GND 43 VCC 44 PF0 45 SYNC OC0A PF1 46 SYNC OC0B XCK0 PF2 47 SYNC/ASYNC OC0C RXD0 PF3 48 SYNC OC0D TXD0 PF4 49 SYNC OC1A PF5 50 SYNC OC1B PF6 51 PF7 52 USARTF1 SPIF TWIF SDA SCL SS XCK1 MOSI SYNC RXD1 MISO SYNC TXD1 SCK Table 33-7. Port H - alternate functions. PORT H PIN # INTERRUPT SDRAM 3P SRAM ALE1 SRAM ALE12 LPC3 ALE1 LPC2 ALE1 LPC2 ALE12 GND 53 VCC 54 PH0 55 SYNC WE WE WE WE WE WE PH1 56 SYNC CAS RE RE RE RE RE PH2 57 SYNC/ASYNC RAS ALE1 ALE1 ALE1 ALE1 ALE1 PH3 58 SYNC DQM PH4 59 SYNC BA0 CS0/A16 CS0 CS0/A16 CS0 CS0/A16 PH5 60 SYNC BA1 CS1/A17 CS1 CS1/A17 CS1 CS1/A17 PH6 61 SYNC CKE CS2/A18 CS2 CS2/A18 CS2 CS2/A18 PH7 62 SYNC CLK CS3/A19 CS3 CS3/A19 CS3 CS3/A19 Notes: 1. 2. ALE2 ALE2 CS0 - CS3 can optionally be moved to Port E or F A16-A23 can optionally be moved to Port E or F when EBI configured in 4PORT mode. Refer to the EBIOUT register description in the XMEGA AU Manual. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 60 Table 33-8. Port J - alternate functions. PORT J PIN # INTERRUPT SDRAM 3P SRAM ALE1 SRAM ALE12 LPC3 ALE1 LPC2 ALE1 LPC2 ALE12 GND 63 VCC 64 PJ0 65 SYNC D0 D0 D0 D0/A0 D0/A0 D0/A0/A8 PJ1 66 SYNC D1 D1 D1 D1/A1 D1/A1 D1/A1/A9 PJ2 67 SYNC/ASYNC D2 D2 D2 D2/A2 D2/A2 D2/A2/A10 PJ3 68 SYNC D3 D3 D3 D3/A3 D3/A3 D3/A3/A11 PJ4 69 SYNC A8 D4 D4 D4/A4 D4/A4 D4/A4/A12 PJ5 70 SYNC A9 D5 D5 D5/A5 D5/A5 D5/A5/A13 PJ6 71 SYNC A10 D6 D6 D6/A6 D6/A6 D6/A6/A14 PJ7 72 SYNC A11 D7 D7 D7/A7 D7/A7 D7/A7/A15 Table 33-9. Port K - alternate functions. PORT K PIN # INTERRUPT SDRAM 3P SRAM ALE1 SRAM ALE2 LPC3 ALE1 GND 73 VCC 74 PK0 75 SYNC A0 A0/A8 A0/A8/A16 A8 PK1 76 SYNC A1 A1/A9 A1/A9/A17 A9 PK2 77 SYNC/ASYNC A2 A2/A10 A2/A10/A18 A10 PK3 78 SYNC A3 A3/A11 A3/A11/A19 A11 PK4 79 SYNC A4 A4/A12 A4/A12/A20 A12 PK5 80 SYNC A5 A5/A13 A5/A13/A21 A13 PK6 81 SYNC A6 A6/A14 A6/A14/A22 A14 PK7 82 SYNC A7 A7/A15 A7/A15/A23 A15 Table 33-10. Port Q - alternate functions. PORT Q PIN # INTERRUPT TOSC VCC 83 GND 84 PQ0 85 SYNC TOSC1 PQ1 86 SYNC TOSC2 PQ2 87 SYNC/ASYNC PQ3 88 SYNC XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 61 Table 33-11. Port R - alternate functions. PORT R PIN # INTERRUPT PDI XTAL PDI 89 PDI_DATA RESET 90 PDI_CLOCK PRO 91 SYNC XTAL2 PR1 92 SYNC XTAL1 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 62 34. Peripheral Module Address Map The address maps show the base address for each peripheral and module in XMEGA A1U. For complete register description and summary for each peripheral module, refer to the XMEGA AU manual. Table 34-1. Peripheral module address map. Base address Name Description 0x0000 GPIO General Purpose IO Registers 0x0010 VPORT0 Virtual Port 0 0x0014 VPORT1 Virtual Port 1 0x0018 VPORT2 Virtual Port 2 0x001C VPORT3 Virtual Port 3 0x0030 CPU CPU 0x0040 CLK Clock Control 0x0048 SLEEP Sleep Controller 0x0050 OSC Oscillator Control 0x0060 DFLLRC32M DFLL for the 32MHz Internal RC Oscillator 0x0068 DFLLRC2M DFLL for the 2MHz RC Oscillator 0x0070 PR Power Reduction 0x0078 RST Reset Controller 0x0080 WDT Watch-Dog Timer 0x0090 MCU MCU Control 0x00A0 PMIC Programmable Multilevel Interrupt Controller 0x00B0 PORTCFG 0x00C0 AES AES Module 0x00D0 CRC CRC Module 0x0100 DMA DMA Controller 0x0180 EVSYS 0x01C0 NVM Non Volatile Memory (NVM) Controller 0x0200 ADCA Analog to Digital Converter on port A 0x0240 ADCB Analog to Digital Converter on port B 0x0300 DACA Digital to Analog Converter on port A 0x0320 DACB Digital to Analog Converter on port B 0x0380 ACA Analog Comparator pair on port A 0x0390 ACB Analog Comparator pair on port B 0x0400 RTC Real Time Counter Port Configuration Event System XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 63 Base address Name Description 0x0440 EBI External Bus Interface 0x0480 TWIC Two Wire Interface on port C 0x0490 TWID Two Wire Interface on port D 0x04A0 TWIE Two Wire Interface on port E 0x04B0 TWIF Two Wire Interface on port F 0x04C0 USB USB Device 0x0600 PORTA Port A 0x0620 PORTB Port B 0x0640 PORTC Port C 0x0660 PORTD Port D 0x0680 PORTE Port E 0x06A0 PORTF Port F 0x06E0 PORTH Port H 0x0700 PORTJ Port J 0x0720 PORTK Port K 0x07C0 PORTQ Port Q 0x07E0 PORTR Port R 0x0800 TCC0 Timer/Counter 0 on port C 0x0840 TCC1 Timer/Counter 1 on port C 0x0880 AWEXC Advanced Waveform Extension on port C 0x0890 HIRESC High Resolution Extension on port C 0x08A0 USARTC0 USART 0 on port C 0x08B0 USARTC1 USART 1 on port C 0x08C0 SPIC 0x08F8 IRCOM 0x0900 TCD0 Timer/Counter 0 on port D 0x0940 TCD1 Timer/Counter 1 on port D 0x0990 HIRESD 0x09A0 USARTD0 USART 0 on port D 0x09B0 USARTD1 USART 1 on port D 0x09C0 SPID Serial Peripheral Interface on port D 0x0A00 TCE0 Timer/Counter 0 on port E 0x0A40 TCE1 Timer/Counter 1 on port E Serial Peripheral Interface on port C Infrared Communication Module High Resolution Extension on port D XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 64 Base address Name Description 0x0A80 AWEXE Advanced Waveform Extension on port E 0x0A90 HIRESE High Resolution Extension on port E 0x0AA0 USARTE0 USART 0 on port E 0x0AB0 USARTE1 USART 1 on port E 0x0AC0 SPIE Serial Peripheral Interface on port E 0x0B00 TCF0 Timer/Counter 0 on port F 0x0B40 TCF1 Timer/Counter 1 on port F 0x0B90 HIRESF 0x0BA0 USARTF0 USART 0 on port F 0x0BB0 USARTF1 USART 1 on port F 0x0BC0 SPIF High Resolution Extension on port F Serial Peripheral Interface on port F XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 65 35. Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks Arithmetic and Logic Instructions ADD Rd, Rr Add without Carry Rd Rd + Rr Z,C,N,V,S,H 1 ADC Rd, Rr Add with Carry Rd Rd + Rr + C Z,C,N,V,S,H 1 ADIW Rd, K Add Immediate to Word Rd Rd + 1:Rd + K Z,C,N,V,S 2 SUB Rd, Rr Subtract without Carry Rd Rd - Rr Z,C,N,V,S,H 1 SUBI Rd, K Subtract Immediate Rd Rd - K Z,C,N,V,S,H 1 SBC Rd, Rr Subtract with Carry Rd Rd - Rr - C Z,C,N,V,S,H 1 SBCI Rd, K Subtract Immediate with Carry Rd Rd - K - C Z,C,N,V,S,H 1 SBIW Rd, K Subtract Immediate from Word Rd + 1:Rd Rd + 1:Rd - K Z,C,N,V,S 2 AND Rd, Rr Logical AND Rd Rd Rr Z,N,V,S 1 ANDI Rd, K Logical AND with Immediate Rd Rd K Z,N,V,S 1 OR Rd, Rr Logical OR Rd Rd v Rr Z,N,V,S 1 ORI Rd, K Logical OR with Immediate Rd Rd v K Z,N,V,S 1 EOR Rd, Rr Exclusive OR Rd Rd Rr Z,N,V,S 1 COM Rd One's Complement Rd $FF - Rd Z,C,N,V,S 1 NEG Rd Two's Complement Rd $00 - Rd Z,C,N,V,S,H 1 SBR Rd,K Set Bit(s) in Register Rd Rd v K Z,N,V,S 1 CBR Rd,K Clear Bit(s) in Register Rd Rd ($FFh - K) Z,N,V,S 1 INC Rd Increment Rd Rd + 1 Z,N,V,S 1 DEC Rd Decrement Rd Rd - 1 Z,N,V,S 1 TST Rd Test for Zero or Minus Rd Rd Rd Z,N,V,S 1 CLR Rd Clear Register Rd Rd Rd Z,N,V,S 1 SER Rd Set Register Rd $FF None 1 MUL Rd,Rr Multiply Unsigned R1:R0 Rd x Rr (UU) Z,C 2 MULS Rd,Rr Multiply Signed R1:R0 Rd x Rr (SS) Z,C 2 MULSU Rd,Rr Multiply Signed with Unsigned R1:R0 Rd x Rr (SU) Z,C 2 FMUL Rd,Rr Fractional Multiply Unsigned R1:R0 Rd x Rr<<1 (UU) Z,C 2 FMULS Rd,Rr Fractional Multiply Signed R1:R0 Rd x Rr<<1 (SS) Z,C 2 FMULSU Rd,Rr Fractional Multiply Signed with Unsigned R1:R0 Rd x Rr<<1 (SU) Z,C 2 DES K Data Encryption if (H = 0) then R15:R0 else if (H = 1) then R15:R0 Encrypt(R15:R0, K) Decrypt(R15:R0, K) PC PC + k + 1 None 2 1/2 Branch instructions RJMP k Relative Jump IJMP Indirect Jump to (Z) PC(15:0) PC(21:16) Z, 0 None 2 EIJMP Extended Indirect Jump to (Z) PC(15:0) PC(21:16) Z, EIND None 2 JMP k Jump PC k None 3 RCALL k Relative Call Subroutine PC PC + k + 1 None 2 / 3 (1) XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 66 Mnemonics Operands Description Operation Flags #Clocks ICALL Indirect Call to (Z) PC(15:0) PC(21:16) Z, 0 None 2 / 3 (1) EICALL Extended Indirect Call to (Z) PC(15:0) PC(21:16) Z, EIND None 3 (1) call Subroutine PC k None 3 / 4 (1) RET Subroutine Return PC STACK None 4 / 5 (1) RETI Interrupt Return PC STACK I 4 / 5 (1) if (Rd = Rr) PC PC + 2 or 3 None 1/2/3 CALL k CPSE Rd,Rr Compare, Skip if Equal CP Rd,Rr Compare CPC Rd,Rr Compare with Carry CPI Rd,K Compare with Immediate SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b) = 0) PC PC + 2 or 3 None 1/2/3 SBRS Rr, b Skip if Bit in Register Set if (Rr(b) = 1) PC PC + 2 or 3 None 1/2/3 SBIC A, b Skip if Bit in I/O Register Cleared if (I/O(A,b) = 0) PC PC + 2 or 3 None 2/3/4 SBIS A, b Skip if Bit in I/O Register Set If (I/O(A,b) =1) PC PC + 2 or 3 None 2/3/4 BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC PC + k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC PC + k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC PC + k + 1 None 1/2 BRGE k Branch if Greater or Equal, Signed if (N V= 0) then PC PC + k + 1 None 1/2 BRLT k Branch if Less Than, Signed if (N V= 1) then PC PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC PC + k + 1 None 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC PC + k + 1 None 1/2 BRTS k Branch if T Flag Set if (T = 1) then PC PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC PC + k + 1 None 1/2 BRVS k Branch if Overflow Flag is Set if (V = 1) then PC PC + k + 1 None 1/2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC PC + k + 1 None 1/2 BRIE k Branch if Interrupt Enabled if (I = 1) then PC PC + k + 1 None 1/2 BRID k Branch if Interrupt Disabled if (I = 0) then PC PC + k + 1 None 1/2 Rd Rr None 1 Rd+1:Rd Rr+1:Rr None 1 Rd K None 1 Rd - Rr Z,C,N,V,S,H 1 Rd - Rr - C Z,C,N,V,S,H 1 Rd - K Z,C,N,V,S,H 1 Data transfer instructions MOV Rd, Rr Copy Register MOVW Rd, Rr Copy Register Pair LDI Rd, K Load Immediate XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 67 Mnemonics Operands Description Flags #Clocks LDS Rd, k Load Direct from data space Rd (k) None 2 (1)(2) LD Rd, X Load Indirect Rd (X) None 1 (1)(2) LD Rd, X+ Load Indirect and Post-Increment Rd X (X) X+1 None 1 (1)(2) LD Rd, -X Load Indirect and Pre-Decrement X X - 1, Rd (X) X-1 (X) None 2 (1)(2) LD Rd, Y Load Indirect Rd (Y) (Y) None 1 (1)(2) LD Rd, Y+ Load Indirect and Post-Increment Rd Y (Y) Y+1 None 1 (1)(2) LD Rd, -Y Load Indirect and Pre-Decrement Y Rd Y-1 (Y) None 2 (1)(2) LDD Rd, Y+q Load Indirect with Displacement Rd (Y + q) None 2 (1)(2) LD Rd, Z Load Indirect Rd (Z) None 1 (1)(2) LD Rd, Z+ Load Indirect and Post-Increment Rd Z (Z), Z+1 None 1 (1)(2) LD Rd, -Z Load Indirect and Pre-Decrement Z Rd Z - 1, (Z) None 2 (1)(2) LDD Rd, Z+q Load Indirect with Displacement Rd (Z + q) None 2 (1)(2) STS k, Rr Store Direct to Data Space (k) Rd None 2 (1) ST X, Rr Store Indirect (X) Rr None 1 (1) ST X+, Rr Store Indirect and Post-Increment (X) X Rr, X+1 None 1 (1) ST -X, Rr Store Indirect and Pre-Decrement X (X) X - 1, Rr None 2 (1) ST Y, Rr Store Indirect (Y) Rr None 1 (1) ST Y+, Rr Store Indirect and Post-Increment (Y) Y Rr, Y+1 None 1 (1) ST -Y, Rr Store Indirect and Pre-Decrement Y (Y) Y - 1, Rr None 2 (1) STD Y+q, Rr Store Indirect with Displacement (Y + q) Rr None 2 (1) ST Z, Rr Store Indirect (Z) Rr None 1 (1) ST Z+, Rr Store Indirect and Post-Increment (Z) Z Rr Z+1 None 1 (1) ST -Z, Rr Store Indirect and Pre-Decrement Z Z-1 None 2 (1) STD Z+q,Rr Store Indirect with Displacement (Z + q) Rr None 2 (1) Load Program Memory R0 (Z) None 3 LPM Operation LPM Rd, Z Load Program Memory Rd (Z) None 3 LPM Rd, Z+ Load Program Memory and Post-Increment Rd Z (Z), Z+1 None 3 Extended Load Program Memory R0 (RAMPZ:Z) None 3 ELPM ELPM Rd, Z Extended Load Program Memory Rd (RAMPZ:Z) None 3 ELPM Rd, Z+ Extended Load Program Memory and PostIncrement Rd Z (RAMPZ:Z), Z+1 None 3 Store Program Memory (RAMPZ:Z) R1:R0 None - Store Program Memory and Post-Increment by 2 (RAMPZ:Z) Z R1:R0, Z+2 None - SPM SPM Z+ XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 68 Mnemonics Operands Description IN Rd, A In From I/O Location OUT A, Rr Out To I/O Location PUSH Rr Push Register on Stack POP Rd XCH Operation Flags #Clocks Rd I/O(A) None 1 I/O(A) Rr None 1 STACK Rr None 1 (1) Pop Register from Stack Rd STACK None 2 (1) Z, Rd Exchange RAM location Temp Rd (Z) Rd, (Z), Temp None 2 LAS Z, Rd Load and Set RAM location Temp Rd (Z) Rd, (Z), Temp v (Z) None 2 LAC Z, Rd Load and Clear RAM location Temp Rd (Z) Rd, (Z), ($FFh - Rd) (Z) None 2 LAT Z, Rd Load and Toggle RAM location Temp Rd (Z) Rd, (Z), Temp (Z) None 2 Rd(n+1) Rd(0) C Rd(n), 0, Rd(7) Z,C,N,V,H 1 Rd(n) Rd(7) C Rd(n+1), 0, Rd(0) Z,C,N,V 1 Rd(0) Rd(n+1) C C, Rd(n), Rd(7) Z,C,N,V,H 1 Bit and bit-test instructions LSL Rd Logical Shift Left LSR Rd Logical Shift Right ROL Rd Rotate Left Through Carry ROR Rd Rotate Right Through Carry Rd(7) Rd(n) C C, Rd(n+1), Rd(0) Z,C,N,V 1 ASR Rd Arithmetic Shift Right Rd(n) Rd(n+1), n=0..6 Z,C,N,V 1 SWAP Rd Swap Nibbles Rd(3..0) Rd(7..4) None 1 BSET s Flag Set SREG(s) 1 SREG(s) 1 BCLR s Flag Clear SREG(s) 0 SREG(s) 1 SBI A, b Set Bit in I/O Register I/O(A, b) 1 None 1 CBI A, b Clear Bit in I/O Register I/O(A, b) 0 None 1 BST Rr, b Bit Store from Register to T T Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) T None 1 SEC Set Carry C 1 C 1 CLC Clear Carry C 0 C 1 SEN Set Negative Flag N 1 N 1 CLN Clear Negative Flag N 0 N 1 SEZ Set Zero Flag Z 1 Z 1 CLZ Clear Zero Flag Z 0 Z 1 SEI Global Interrupt Enable I 1 I 1 CLI Global Interrupt Disable I 0 I 1 SES Set Signed Test Flag S 1 S 1 CLS Clear Signed Test Flag S 0 S 1 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 69 Mnemonics Operands Description Operation Flags #Clocks SEV Set Two's Complement Overflow V 1 V 1 CLV Clear Two's Complement Overflow V 0 V 1 SET Set T in SREG T 1 T 1 CLT Clear T in SREG T 0 T 1 SEH Set Half Carry Flag in SREG H 1 H 1 CLH Clear Half Carry Flag in SREG H 0 H 1 None 1 None 1 MCU control instructions BREAK Break NOP No Operation SLEEP Sleep (see specific descr. for Sleep) None 1 WDR Watchdog Reset (see specific descr. for WDR) None 1 Notes: 1. 2. (See specific descr. for BREAK) Cycle times for Data memory accesses assume internal memory accesses, and are not valid for accesses via the external RAM interface. One extra cycle must be added when accessing Internal SRAM. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 70 36. Packaging information 36.1 100A PIN 1 B PIN 1 IDENTIFIER E1 e E D1 D C 0~7 A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation AED. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.08mm maximum. SYMBOL MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 E1 13.90 14.00 14.10 B 0.17 - 0.27 C 0.09 - 0.20 L 0.45 - 0.75 e NOTE Note 2 Note 2 0.50 TYP 2010-10-20 R 2325 Orchard Parkway San Jose, CA 95131 DRAWING NO. TITLE 100A, 100-lead, 14 x 14mm Body Size, 1.0mm Body Thickness, 0.5mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) 100A REV. D XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 71 36.2 100C1 0.12 Z E Marked A1 Identifier SIDE VIEW D A TOP VIEW A1 Ob e A1 Corner 0.90 TYP 10 9 8 7 6 5 4 3 2 1 A 0.90 TYP B C D COMMON DIMENSIONS (Unit of Measure = mm) E D1 F e SYMBOL MIN H A 1.10 - 1.20 I A1 0.30 0.35 0.40 D 8.90 9.00 9.10 E 8.90 9.00 9.10 D1 7.10 7.20 7.30 G J E1 BOTTOM VIEW NOM MAX E1 7.10 7.20 7.30 Ob 0.35 0.40 0.45 e NOTE 0.80 TYP 5/25/06 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 100C1, 100-ball, 9 x 9 x 1.2 mm Body, Ball Pitch 0.80 mm Chip Array BGA Package (CBGA) DRAWING NO. 100C1 REV. A XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 72 36.3 100C2 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 73 37. Electrical Characteristics All typical values are measured at T = 25C unless other temperature condition is given. All minimum and maximum values are valid across operating temperature and voltage unless other conditions are given. Note: 37.1 For devices that are not available yet, preliminary values in this datasheet are based on simulations, and/or characterization of similar AVR XMEGA microcontrollers. After the device is characterized the final values will be available, hence existing values can change. Missing minimum and maximum values will be available after the device is characterized. ATxmega64A1U 37.1.1 Absolute Maximum Ratings Stresses beyond those listed in Table 37-1 on page 74 under may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 37-1. Absolute maximum ratings. Symbol Parameter Condition Min. Typ. -0.3 Max. Units 4 V VCC Power supply voltage IVCC Current into a VCC pin 200 IGND Current out of a Gnd pin 200 VPIN Pin voltage with respect to Gnd and VCC -0.5 VCC+0.5 V IPIN I/O pin sink/source current -25 25 mA TA Storage temperature -65 150 Tj Junction temperature mA C 150 37.1.2 General Operating Ratings The device must operate within the ratings listed in Table 37-2 in order for all other electrical characteristics and typical characteristics of the device to be valid. Table 37-2. General operating conditions. Symbol Parameter Condition Min. Typ. Max. VCC Power supply voltage 1.60 3.6 AVCC Analog supply voltage 1.60 3.6 TA Temperature range -40 85 Tj Junction temperature -40 105 Units V C XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 74 Table 37-3. Operating voltage and frequency. Symbol Parameter ClkCPU Condition CPU clock frequency Min. Typ. Max. VCC = 1.6V 0 12 VCC = 1.8V 0 12 VCC = 2.7V 0 32 VCC = 3.6V 0 32 Units MHz The maximum CPU clock frequency depends on VCC. As shown in Figure 37-1 the Frequency vs. VCC curve is linear between 1.8V < VCC < 2.7V. Figure 37-1. Maximum Frequency vs. VCC. MHz 32 Safe Operating Area 12 1.6 1.8 2.7 3.6 V XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 75 37.1.3 Current consumption Table 37-4. Current consumption for Active mode and sleep modes. Symbol Parameter Condition 32kHz, Ext. Clk Active power consumption(1) 1MHz, Ext. Clk 2MHz, Ext. Clk 32MHz, Ext. Clk 32kHz, Ext. Clk Idle power consumption(1) 1MHz, Ext. Clk 2MHz, Ext. Clk 32MHz, Ext. Clk ICC T = 25C Min. T = 85C 50 VCC = 3.0V 95 VCC = 1.8V 350 VCC = 3.0V 700 VCC = 1.8V 650 700 1.2 1.4 15 20 VCC = 3.0V Power-save power consumption(2) Reset power consumption Notes: 1. 2. mA 3.5 VCC = 3.0V 6.4 VCC = 1.8V 109 VCC = 3.0V 200 VCC = 1.8V 290 380 476 650 6.6 9.2 0.1 1.0 0.1 1.0 1.7 5.0 1.3 3.0 3.1 10 VCC = 3.0V VCC = 1.8V VCC = 3.0V A mA VCC = 3.0V RTC on ULP clock, WDT and sampled BOD enabled, T = 25C VCC = 1.8V 1.2 VCC = 3.0V 1.3 RTC on 1.024kHz low power 32.768kHz TOSC, T = 25C VCC = 1.8V 0.7 2.0 VCC = 3.0V 0.8 2.0 RTC from low power 32.768kHz TOSC, T = 25C VCC = 1.8V 0.9 3.0 VCC = 3.0V 1.0 3.0 VCC = 3.0V 914 Current through RESET pin subtracted Units A VCC = 1.8V WDT and sampled BOD enabled, T = 25C WDT and sampled BOD enabled, T = 85C Max. VCC = 1.8V T = 25C Power-down power consumption Typ. A All Power Reduction Registers set. Maximum limits are based on characterization, and not tested in production. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 76 Table 37-5. Current consumption for modules and peripherals. Symbol Parameter Condition(1) Min. Typ. ULP oscillator 1.0 32.768kHz int. oscillator 27 Max. Units 85 2MHz int. oscillator DFLL enabled with 32.768kHz int. osc. as reference 120 310 32MHz int. oscillator DFLL enabled with 32.768kHz int. osc. as reference Watchdog timer 560 A 1.0 Continuous mode 126 Sampled mode, includes ULP oscillator 1.2 BOD Internal 1.0V reference 89 Temperature sensor 83 3.0 ICC ADC DAC 250ksps VREF = Ext ref 250ksps VREF = Ext ref No load CURRLIMIT = LOW 2.6 CURRLIMIT = MEDIUM 2.1 CURRLIMIT = HIGH 1.6 Normal mode 1.9 Low Power mode 1.1 High speed mode 324 Low power mode 122 615KBps between I/O registers and SRAM 140 mA AC DMA Timer/counter USART 20 Rx and Tx enabled, 9600 BAUD Flash memory and EEPROM programming Note: 1. A 4 4 mA All parameters measured as the difference in current consumption between module enabled and disabled. All data at VCC = 3.0V, ClkSYS = 1MHz external clock without prescaling, T = 25C unless other conditions are given. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 77 37.1.4 Wake-up time from sleep modes Table 37-6. Device wake-up time from sleep modes with various system clock sources. Symbol Parameter Wake-up time from idle, standby, and extended standby mode twakeup Min. Typ. (1) External 2MHz clock 2.0 32.768kHz internal oscillator 120 2MHz internal oscillator 2.0 32MHz internal oscillator 0.2 External 2MHz clock 4.5 32.768kHz internal oscillator 320 2MHz internal oscillator 10 32MHz internal oscillator 5.5 Max. Units s Wake-up time from Power-save and Power-down mode Note: Condition 1. The wake-up time is the time from the wake-up request is given until the peripheral clock is available on pin, see Figure 37-2. All peripherals and modules start execution from the first clock cycle, expect the CPU that is halted for four clock cycles before program execution starts. Figure 37-2. Wake-up time definition. Wakeup time Wakeup request Clock output XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 78 37.1.5 I/O Pin Characteristics The I/O pins complies with the JEDEC LVTTL and LVCMOS specification and the high- and low level input and output voltage limits reflect or exceed this specification. Table 37-7. I/O pin characteristics. Symbol Parameter Condition Min. Typ. Max. Units -20 20 mA VCC = 2.7 - 3.6V 2 VCC+0.3 VCC = 2.0 - 2.7V 0.7*VCC VCC+0.3 VCC = 1.6 - 2.0V 0.7*VCC VCC+0.3 VCC = 2.7- 3.6V -0.3 0.3*VCC VCC = 2.0 - 2.7V -0.3 0.3*VCC VCC = 1.6 - 2.0V -0.3 0.3*VCC (1) IOH / IOL (2) I/O pin source/sink current VIH High level input voltage VIL Low level input voltage VCC = 3.0 - 3.6V IOH = -2mA 2.4 0.94*VCC IOH = -1mA 2.0 0.96*VCC IOH = -2mA 1.7 0.92*VCC VCC = 3.3V IOH = -8mA 2.6 2.9 VCC = 3.0V IOH = -6mA 2.1 2.6 VCC = 1.8V IOH = -2mA 1.4 1.6 VCC = 3.0 - 3.6V IOL = 2mA 0.05*VCC 0.4 IOL = 1mA 0.03*VCC 0.4 IOL = 2mA 0.06*VCC 0.7 VCC = 3.3V IOL = 15mA 0.4 0.76 VCC = 3.0V IOL = 10mA 0.3 0.64 VCC = 1.8V IOL = 5mA 0.3 0.46 <0.001 0.1 VCC = 2.3 - 2.7V VOH High level output voltage VCC = 2.3 - 2.7V VOL Low level output voltage IIN Input leakage current RP I/O pin Pull/Buss keeper resistor 25 Reset pin pull-up resistor 25 V A k RRST 4 tr Notes: Pad rise time No load ns slew rate limitation 1. 2. 7 The sum of all IOH for PORTA, PORTC, PORTD, PORTF, PORTH, PORTJ, PORTK must for each port not exceed 200mA. The sum of all IOH for PORTB must not exceed 100mA. The sum of all IOH for PORTQ, PORTR and PDI must not exceed 100mA. The sum of all IOL for PORTA, PORTC, PORTD, PORTF, PORTH, PORTJ, PORTK must for each port not exceed 200mA. The sum of all IOL for PORTB must not exceed 100mA. The sum of all IOL for PORTQ, PORTR and PDI must not exceed 100mA. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 79 37.1.6 ADC characteristics Table 37-8. Power supply, reference and input range. Symbol Parameter AVCC Analog supply voltage VREF Reference voltage Condition Min. Typ. Max. VCC- 0.3 VCC+ 0.3 1 AVCC- 0.6 Units V Rin Input resistance Switched 5.0 k Cin Input capacitance Switched 5.0 pF RAREF Reference input resistance (leakage only) >10 M CAREF Reference input capacitance Static load 7 pF VIN Input range Conversion range Differential mode, Vinp - Vinn VIN Conversion range Single ended unsigned mode, Vinp V Fixed offset voltage -0.1 AVCC+0.1 -VREF VREF -V VREF-V 190 V LSB Table 37-9. Clock and timing. Symbol ClkADC fclkADC Parameter Condition Min. Typ. Max. Units Maximum is 1/4 of peripheral clock frequency 100 Measuring internal signals 100 125 100 2000 Measuring internal signals 100 125 Sampling time 1/2 ClkADC cycle 0.25 5 s Conversion time (latency) (RES+2)/2+(GAIN !=0) RES (Resolution) = 12 5 8 ClkADC cycles Start-up time ADC clock cycles 12 24 After changing reference or input mode 7 7 After ADC flush 1 1 ADC clock frequency 2000 kHz Sample rate ksps ADC settling time XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 ClkADC cycles 80 Table 37-10. Accuracy characteristics. Symbol Parameter RES Resolution INL(1) DNL(1) Integral non-linearity Differential non-linearity Offset Error Condition(2) Programmable to 12-bit 1. 2. Max. Units 11 11.5 12 Bits VCC-1.0V < VREF< VCC-0.6V 1.2 2 All VREF 1.5 3 2000ksps, differential mode VCC-1.0V < VREF< VCC-0.6V 1.0 2 All VREF 1.5 3 single ended mode 1.5 4 guaranteed monotonic <0.5 <1 lsb -1 mV Temperature drift <0.01 mV/K Operating voltage drift <0.6 mV/V External reference -1 AVCC/1.6 10 AVCC/2.0 8 Bandgap 5 Gain Error Notes: Typ. 500ksps, differential mode Differential mode Noise Min. mV Temperature drift <0.02 mV/K Operating voltage drift <0.5 mV/V Differential mode, shorted input 2msps, VCC = 3.6V, ClkPER = 16MHz 0.4 mV rms Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% input voltage range. Unless otherwise noted all linearity, offset and gain error numbers are valid under the condition that external VREF is used. Table 37-11. Gain stage characteristics. Symbol Parameter Condition Min. Typ. Max. Units Rin Input resistance Switched in normal mode 4.0 k Csample Input capacitance Switched in normal mode 4.4 pF Signal range Gain stage output Propagation delay ADC conversion rate Sample rate Same as ADC INL(1) Integral Non-Linearity 500ksps 0 VCC- 0.6 ClkADC cycles 1 100 All gain settings 1.5 V 1000 kHz 3 lsb XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 81 Symbol Parameter Gain Error Offset Error, input referred Condition Min. 1x gain, normal mode -0.7 8x gain, normal mode -3.0 64x gain, normal mode -4.8 1x gain, normal mode 0.4 8x gain, normal mode 0.4 64x gain, normal mode 0.4 1x gain, normal mode Noise 8x gain, normal mode 1. Max. Units % mV 0.6 VCC = 3.6V mV rms 2.0 Ext. VREF 64x gain, normal mode Note: Typ. 11 Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% input voltage range. 37.1.7 DAC Characteristics Table 37-12. Power supply, reference and output range. Symbol Parameter AVCC Analog supply voltage AVREF External reference voltage Rchannel DC output impedance Condition Linear output voltage range RAREF CAREF Min. Max. VCC+ 0.3 1.0 VCC- 0.6 V 50 AVCC-0.15 V 0.15 Static load Minimum resistance load Units VCC- 0.3 Reference input resistance Reference input capacitance Typ. >10 M 7 pF 1 k 100 pF 1 nF AVCC/100 0 mA Maximum capacitance load 1000 serial resistance Operating within accuracy specification Output sink/source Safe operation 10 Table 37-13. Clock and timing. Symbol Fclk Parameter Conversion rate Condition Fout=Fclk/4, Cload=100pF, maximum step size Min. 0 Typ. Max. Units 1000 ksps XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 82 Table 37-14. Accuracy characteristics. Symbol RES Parameter Condition Min. Input resolution VREF= Ext 1.0V INL(1) Integral non-linearity VREF=AVCC VREF=INT1V VREF=Ext 1.0V DNL(1) Differential non-linearity VREF=AVCC VREF=INT1V Gain error Units 12 Bits 2.0 3 VCC = 3.6V 1.5 2.5 VCC = 1.6V 2.0 4 VCC = 3.6V 1.5 4 VCC = 1.6V 5.0 VCC = 3.6V 5.0 VCC = 1.6V 1.5 3.0 VCC = 3.6V 0.6 1.5 VCC = 1.6V 1.0 3.5 VCC = 3.6V 0.6 1.5 VCC = 1.6V 4.5 VCC = 3.6V 4.5 lsb After calibration <4 4 Gain calibration drift VREF= Ext 1.0V <0.2 mV/K Offset error After calibration <1 lsb Offset calibration step size 1. Max. VCC = 1.6V Gain calibration step size Note: Typ. 1 Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% output voltage range. 37.1.8 Analog Comparator Characteristics Table 37-15. Analog Comparator characteristics. Symbol Parameter Voff Input offset voltage Ilk Input leakage current Condition Input voltage range Vhys1 Hysteresis, none Vhys2 Hysteresis, small Vhys3 Hysteresis, large Min. Typ. Max. Units <10 mV <1 nA -0.1 AVCC +0.1 V 0 mode = High Speed (HS) 22 mode = Low Power (LP) 30 mode = HS 43 mode = LP 60 mV XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 83 Symbol Parameter Condition VCC = 3.0V, T= 85C tdelay Propagation delay Min. mode = HS mode = HS VCC = 3.0V, T= 85C Typ. Max. 60 90 60 mode = LP Units ns 130 Current source calibration range Single mode 2 8 Double mode 4 16 64-Level Voltage Scaler Integral non-linearity (INL) s 0.3 0.5 lsb 37.1.9 Bandgap and Internal 1.0V Reference Characteristics Table 37-16. Bandgap and Internal 1.0V reference characteristics. Symbol Parameter Condition Min. As reference for ADC or DAC Typ. Max. 1 ClkPER + 2.5s Startup time As input voltage to ADC and AC Units s 1.5 Bandgap voltage 1.1 V INT1V Internal 1.00V reference for ADC and DAC T= 85C, after calibration Variation over voltage and temperature Relative to T= 85C, VCC = 3.0V 0.99 1 1.01 1.0 % 37.1.10 Brownout Detection Characteristics Table 37-17. Brownout detection characteristics. Symbol Parameter Condition BOD level 0 falling VCC VBOT VHYST Typ. Max. 1.60 1.62 1.72 BOD level 1 falling VCC 1.8 BOD level 2 falling VCC 2.0 BOD level 3 falling VCC 2.2 BOD level 4 falling VCC 2.4 BOD level 5 falling VCC 2.6 BOD level 6 falling VCC 2.8 BOD level 7 falling VCC 3.0 0.4 Detection time s Sampled mode Hysteresis Units V Continuous mode tBOD Min. 1000 1.4 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 % 84 37.1.11 External Reset Characteristics Table 37-18. External reset characteristics. Symbol tEXT Parameter Condition Min. Typ. Max. Units 86 1000 ns Minimum reset pulse width Reset threshold voltage (VIH) VRST Reset threshold voltage (VIL) VCC = 2.7 - 3.6V 0.60*VCC VCC = 1.6 - 2.7V 0.60*VCC VCC = 2.7 - 3.6V 0.40*VCC VCC = 1.6 - 2.7V 0.40*VCC V 37.1.12 Power-on Reset Characteristics Table 37-19. Power-on reset characteristics. Symbol Parameter VPOT- (1) POR threshold voltage falling VCC VPOT+ POR threshold voltage rising VCC Note: 1. Condition Min. Typ. VCC falls faster than 1V/ms 0.4 1.0 VCC falls at 1V/ms or slower 0.8 1.0 Max. Units V 1.3 1.59 Typ. Max. VPOT- values are only valid when BOD is disabled. When BOD is enabled VPOT- = VPOT+. 37.1.13 Flash and EEPROM Memory Characteristics Table 37-20. Endurance and data retention. Symbol Parameter Condition Min. 25C 10K 85C 10K 25C 100 55C 25 25C 80K 85C 30K 25C 100 55C 25 Write/Erase cycles Units Cycle Flash Data retention Year Write/Erase cycles Cycle EEPROM Data retention Year XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 85 Table 37-21. Programming time. Symbol Parameter Chip Erase Flash EEPROM Notes: 1. 2. Condition Min. Typ. (1) 64KB Flash, EEPROM(2) and SRAM Erase 55 Page Erase 4 Page Write 4 Atomic Page Erase and Write 8 Page Erase 4 Page Write 4 Atomic Page Erase and Write 8 Max. Units ms Programming is timed from the 2MHz internal oscillator. EEPROM is not erased if the EESAVE fuse is programmed. 37.1.14 Clock and Oscillator Characteristics 37.1.14.1 Calibrated 32.768kHz Internal Oscillator characteristics Table 37-22. 32.768kHz internal oscillator characteristics. Symbol Parameter Condition Min. Frequency Factory calibration accuracy Typ. Max. 32.768 T = 85C, VCC = 3.0V User calibration accuracy Units kHz -0.5 0.5 -0.5 0.5 % 37.1.14.2 Calibrated 2MHz RC Internal Oscillator characteristics Table 37-23. 2MHz internal oscillator characteristics. Symbol Parameter Tunable frequency range Condition Min. DFLL can tune to this frequency over voltage and temperature 1.8 Typ. Max. Units 2.2 MHz Factory calibrated frequency 2.0 Factory calibration accuracy T = 85C, VCC= 3.0V DFLL calibration stepsize T = 25C, VCC= 3.0V -1.5 1.5 % 0.23 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 86 37.1.14.3 Calibrated and tunable 32MHz internal oscillator characteristics Table 37-24. 32MHz internal oscillator characteristics. Symbol Parameter Tunable frequency range Condition Min. DFLL can tune to this frequency over voltage and temperature 30 Max. Units 35 MHz Factory calibrated frequency Factory calibration accuracy Typ. 32 T = 85C, VCC= 3.0V -1.5 1.5 % DFLL calibration step size 0.24 37.1.14.4 32kHz Internal ULP Oscillator characteristics Table 37-25. 32kHz internal ULP oscillator characteristics. Symbol Parameter Condition Min. Output frequency Typ. Max. 32 Accuracy -30 Units kHz 30 % Max. Units 37.1.14.5 Internal Phase Locked Loop (PLL) characteristics Table 37-26. Internal PLL characteristics. Symbol fIN Parameter Input frequency Output frequency(1) fOUT Condition Output frequency must be within fOUT 1. Typ. TBD VCC= 1.6 20 32 VCC= 2.7 20 96 VCC= 3.6V 20 128 Duty cycle Note: Min. MHz 50 Start-up lock time fOUT = 48MHz 18 Re-lock time fOUT-init = 10MHz, fOUT-end = 64MHz 17 % s The maximum output frequency vs. supply voltage is linear between 1.8V and 2.7V, and can never be higher than four times the maximum CPU frequency. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 87 37.1.14.6 External clock characteristics Figure 37-3. External clock drive waveform. tCH tCH tCF tCR VIH1 VIL1 tCL tCK Table 37-27. External clock(1). Symbol Parameter Clock frequency(2) 1/tCK tCK Clock period tCH/CL Clock high/low time VIL/IH Low/high level input voltage tCK Reduction in period from one clock cycle to the next Notes: 1. 2. Condition Min. Typ. Max. VCC = 1.6 - 1.8V 90 VCC = 2.7 - 3.6V 142 Units MHz VCC = 1.6 - 1.8V 11 VCC = 2.7 - 3.6V 7 VCC = 1.6 - 1.8V 4.5 VCC = 2.7 - 3.6V 2.4 ns See Table 37-7 on page 79 V 10 % System Clock Prescalers must be set so that maximum CPU clock frequency for device is not exceeded. The maximum frequency vs. supply voltage is linear between 1.8V and 2.7V, and the same applies for all other parameters with supply voltage conditions. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 88 37.1.14.7 External 16MHz crystal oscillator and XOSC characteristics Table 37-28. External 16MHz crystal oscillator and XOSC characteristics. . Symbol Parameter Condition Min. Typ. FRQRANGE=0 <10 FRQRANGE=1, 2, 3 <1 Max. Cycle to cycle jitter Units ns FRQRANGE=0 <0.5 FRQRANGE=1 <0.05 FRQRANGE=2 <0.005 FRQRANGE=3 <0.005 FRQRANGE=0 50 FRQRANGE=1 50 FRQRANGE=2 50 FRQRANGE=3 50 Frequency error % Duty cycle FRQRANGE=0 FRQRANGE=1 RQ Negative impedance(1) FRQRANGE=2 FRQRANGE=3 ESR SF = safety factor 0.4MHz resonator, CL=100pF 13k 1MHz crystal, CL=20pF 9k 2MHz crystal, CL=20pF 2.2k 1MHz crystal, CL=20pF 2.3k 2MHz crystal, CL=20pF 8k 9MHz crystal, CL=20pF 200 8MHz crystal, CL=20pF 225 9MHz crystal, CL=20pF 300 12MHz crystal, CL=10pF 175 8MHz crystal, CL=20pF 340 9MHz crystal, CL=20pF 400 12MHz crystal, CL=10pF 330 12MHz crystal, CL=12pF 230 16MHz crystal, CL=10pF 115 min(RQ)/SF XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 k 89 Symbol Parameter Condition Start-up time Min. Typ. XOSCPWR=0, FRQRANGE=0 0.4MHz resonator, CL=100pF 1.0 XOSCPWR=0, FRQRANGE=1 2MHz crystal, CL=20pF 2.6 XOSCPWR=0, FRQRANGE=2 8MHz crystal, CL=20pF 0.8 XOSCPWR=0, FRQRANGE=3 12MHz crystal, CL=20pF 1.0 XOSCPWR=1, FRQRANGE=3 16MHz crystal, CL=20pF 1.4 CXTAL1 Parasitic capacitance XTAL1 pin 6 CXTAL2 Parasitic capacitance XTAL2 pin 10 CLOAD Parasitic capacitance load 3.8 Note: 1. Max. Units ms pF Numbers for negative impedance are not tested in production but guaranteed from design and characterization. 37.1.14.8 External 32.768kHz crystal oscillator and TOSC characteristics Table 37-29. External 32.768kHz crystal oscillator and TOSC characteristics. Symbol Parameter Condition ESR/R1 Recommended crystal equivalent series resistance (ESR) Min. Typ. Crystal load capacitance 6.5pF 60 Crystal load capacitance 9.0pF 35 Parasitic capacitance TOSC1 pin 4.0 CTOSC2 Parasitic capacitance TOSC2 pin 4.1 Parasitic capacitance load 2.0 Recommended safety factor Note: 1. Units k CTOSC1 CL Max. Capacitive load matched to crystal specification pF 3 See Figure 37-4 for definition. Figure 37-4. TOSC input capacitance. CL1 TOSC1 CL2 Device internal External TOSC2 32.768kHz crystal XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 90 The parasitic capacitance between the TOSC pins is CL1 + CL2 in series as seen from the crystal when oscillating without external capacitors. 37.1.15 SPI Characteristics Figure 37-5. SPI timing requirements in master mode. SS tSCKR tMOS tSCKF SCK (CPOL = 0) tSCKW SCK (CPOL = 1) tSCKW tMIS MISO (Data Input) tMIH tSCK MSB LSB tMOH tMOH MOSI (Data Output) MSB LSB Figure 37-6. SPI timing requirements in slave mode. SS tSSS tSCKR tSCKF tSSH SCK (CPOL = 0) tSSCKW SCK (CPOL = 1) tSSCKW tSIS MOSI (Data Input) tSIH MSB tSOSSS MISO (Data Output) tSSCK LSB tSOS MSB tSOSSH LSB XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 91 Table 37-30. SPI timing characteristics and requirements. Symbol Parameter tSCK SCK period Master (See Table 21-4 in XMEGA AU Manual) tSCKW SCK high/low width Master 0.5*SCK tSCKR SCK rise time Master 2.7 tSCKF SCK fall time Master 2.7 tMIS MISO setup to SCK Master 11 tMIH MISO hold after SCK Master 0 tMOS MOSI setup SCK Master 0.5*SCK MOSI hold after SCK Master 1 SCK to out high Master 1 Slave SCK period Slave 4*tClkPER tSSCKW SCK high/low width Slave 2*tClkPER tSSCKR SCK rise time Slave 1600 tSSCKF SCK fall time Slave 1600 tSIS MOSI setup to SCK Slave 3 tSIH MOSI hold after SCK Slave tSCK tSSS SS setup to SCK Slave 20 tSSH SS hold after SCK Slave 20 tSOS MISO setup SCK Slave 8 tSOH MISO hold after SCK Slave 13 tSOSS MISO setup after SS low Slave 11 tSOSH MISO hold after SS high Slave 8 tMOH tSSCK Condition Min. Typ. Max. Units ns XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 92 37.1.16 EBI characteristics Table 37-31. EBI SRAM characteristics and requirements. Symbol Parameter tClkPER2 SRAM clock period Condition Min. Typ. Max. Units 0.5*tClkPER tALH SRAM address hold after ALE low tClkPER2 tALS SRAM address setup before ALE low (read and write) tClkPER2 tALW SRAM ALE width tClkPER2 tARH SRAM address hold after RE high tClkPER2 tARS SRAM address setup before RE high tClkPER2 tAWH SRAM address hold after WE high tClkPER2 tAWS SRAM Address setup before WE high tClkPER2 tDRH SRAM data hold after RE high tDRS SRAM data setup to RE high 3.0V tDRS SRAM data setup to RE high 2.7V, 85C 17 tDRS SRAM data setup to RE high 1.6V, 85C 27 tDWH SRAM data hold after WE high tClkPER2 tDWS SRAM data setup to WE high tClkPER2 tRW SRAM read enable pulse width tClkPER2*SRWS tWW SRAM write enable pulse width tClkPER2*SRWS tCH SRAM chip select hold after RE/WE high tCRS SRAM chip select setup to RE low or ALE high tCWS SRAM chip select setup to WE low (no ALE) 0 12 ns tClkPER2 0 tClkPER2 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 93 Table 37-32. EBI SDRAM characteristics and requirements. Symbol Parameter Condition tClkPER2 SDRAM clock period Min. Typ. Max. Units 0.5*tClkPER tAH SDRAM address hold time 0.5*tClkPER2 tAS SDRAM address setup time 0.5*tClkPER2 tCH SDRAM clock high-level width 0.5*tClkPER2 tCL SDRAM clock low-level width 0.5*tClkPER2 tCKH SDRAM CKE hold time 0.5*tClkPER2 tCKS SDRAM CKE setup time 0.5*tClkPER2 tCMH SDRAM CS, RAS, CAS, WE, DQM hold time 0.5*tClkPER2 tCMS SDRAM CS, RAS, CAS, WE, DQM setup time 0.5*tClkPER2 tDRH SDRAM data in hold after CLK high tAC SDRAM access time from CLK ns 0 tClkPER-5 tDWH SDRAM data out hold after CLK high 0.5*tClkPER2 tDWS SDRAM data out setup before CLK high 0.5*tClkPER2 37.1.17 Two-Wire Interface Characteristics Table 37-33 on page 95 describes the requirements for devices connected to the Two-Wire Interface Bus. The Atmel AVR XMEGA Two-Wire Interface meets or exceeds these requirements under the noted conditions. Timing symbols refer to Figure 37-7. Figure 37-7. Two-Wire Interface bus timing. tof tHIGH tLOW tr SCL tSU;STA tHD;DAT tHD;STA tSU;DAT tSU;STO SDA tBUF XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 94 Table 37-33. Two-wire interface characteristics. Symbol Parameter Condition Min. Typ. Max. Units VIH Input high voltage 0.7*VCC VCC+0.5 VIL Input low voltage -0.5 0.3*VCC Vhys Hysteresis of Schmitt trigger inputs 0.05*VCC (1) 0 0 0.4 20+0.1Cb (1)(2) 0 20+0.1Cb (1)(2) 300 0 50 -10 10 A 10 pF 400 kHz VOL Output low voltage tr Rise time for both SDA and SCL tof Output fall time from VIHmin to VILmax tSP Spikes suppressed by input filter II Input current for each I/O pin CI Capacitance for each I/O pin fSCL SCL clock frequency 3mA, sink current 10pF < Cb < 400pF (2) 0.1VCC < VI < 0.9VCC fPER (3)>max(10fSCL, 250kHz) 0 fSCL 100kHz RP tHD;STA tLOW tHIGH Value of pull-up resistor fSCL > 100kHz Hold time (repeated) START condition Low period of SCL clock High period of SCL clock tSU;STA Set-up time for a repeated START condition tHD;DAT Data hold time tSU;DAT Data setup time tSU;STO tBUF Setup time for STOP condition Bus free time between a STOP and START condition V CC - 0.4V ---------------------------3mA 100ns --------------Cb 300ns --------------Cb fSCL 100kHz 4.0 fSCL > 100kHz 0.6 fSCL 100kHz 4.7 fSCL > 100kHz 1.3 fSCL 100kHz 4.0 fSCL > 100kHz 0.6 fSCL 100kHz 4.7 fSCL > 100kHz 0.6 fSCL 100kHz 0 3.5 fSCL > 100kHz 0 0.9 fSCL 100kHz 250 fSCL > 100kHz 100 fSCL 100kHz 4.0 fSCL > 100kHz 0.6 fSCL 100kHz 4.7 fSCL > 100kHz 1.3 V ns s s Notes: 1. Required only for fSCL > 100kHz. 2. Cb = Capacitance of one bus line in pF. 3. fPER = Peripheral clock frequency. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 95 37.2 ATxmega128A1U 37.2.1 Absolute Maximum Ratings Stresses beyond those listed in Table 37-34 on page 96 under may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 37-34. Absolute maximum ratings. Symbol Parameter Condition Min. Typ. Max. Units 4 V VCC Power supply voltage -0.3 IVCC Current into a VCC pin 200 IGND Current out of a Gnd pin 200 VPIN Pin voltage with respect to Gnd and VCC -0.5 VCC+0.5 V IPIN I/O pin sink/source current -25 25 mA TA Storage temperature -65 150 Tj Junction temperature mA C 150 37.2.2 General Operating Ratings The device must operate within the ratings listed in Table 37-35 in order for all other electrical characteristics and typical characteristics of the device to be valid. Table 37-35. General operating conditions. Symbol Parameter Condition Min. Typ. Max. VCC Power supply voltage 1.60 3.6 AVCC Analog supply voltage 1.60 3.6 TA Temperature range -40 85 Tj Junction temperature -40 105 Units V C Table 37-36. Operating voltage and frequency. Symbol ClkCPU Parameter CPU clock frequency Condition Min. Typ. Max. VCC = 1.6V 0 12 VCC = 1.8V 0 12 VCC = 2.7V 0 32 VCC = 3.6V 0 32 Units MHz The maximum CPU clock frequency depends on VCC. As shown in Figure 37-8 the Frequency vs. VCC curve is linear between 1.8V < VCC < 2.7V. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 96 Figure 37-8. Maximum Frequency vs. VCC. MHz 32 Safe Operating Area 12 1.6 1.8 2.7 3.6 V XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 97 37.2.3 Current consumption Table 37-37. Current consumption for Active mode and sleep modes. Symbol Parameter Condition 32kHz, Ext. Clk Active power consumption(1) 1MHz, Ext. Clk 2MHz, Ext. Clk 32MHz, Ext. Clk 32kHz, Ext. Clk Idle power consumption(1) 1MHz, Ext. Clk 2MHz, Ext. Clk 32MHz, Ext. Clk ICC T = 25C Min. T = 85C 50 VCC = 3.0V 95 VCC = 1.8V 350 VCC = 3.0V 700 VCC = 1.8V 650 700 1.2 1.4 15 20 VCC = 3.0V Power-save power consumption(2) Reset power consumption Notes: 1. 2. mA 3.5 VCC = 3.0V 6.4 VCC = 1.8V 109 VCC = 3.0V 200 VCC = 1.8V 290 380 476 650 6.6 9.2 0.1 1.0 0.1 1.0 1.7 5.0 1.3 3.0 3.1 10 VCC = 3.0V VCC = 1.8V VCC = 3.0V A mA VCC = 3.0V RTC on ULP clock, WDT and sampled BOD enabled, T = 25C VCC = 1.8V 1.2 VCC = 3.0V 1.3 RTC on 1.024kHz low power 32.768kHz TOSC, T = 25C VCC = 1.8V 0.7 2.0 VCC = 3.0V 0.8 2.0 RTC from low power 32.768kHz TOSC, T = 25C VCC = 1.8V 0.9 3.0 VCC = 3.0V 1.0 3.0 VCC = 3.0V 914 Current through RESET pin subtracted Units A VCC = 1.8V WDT and sampled BOD enabled, T = 25C WDT and sampled BOD enabled, T = 85C Max. VCC = 1.8V T = 25C Power-down power consumption Typ. A All Power Reduction Registers set. Maximum limits are based on characterization, and not tested in production. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 98 Table 37-38. Current consumption for modules and peripherals. Symbol Parameter Condition(1) Min. Typ. ULP oscillator 1.0 32.768kHz int. oscillator 27 Max. Units 85 2MHz int. oscillator DFLL enabled with 32.768kHz int. osc. as reference 120 310 32MHz int. oscillator DFLL enabled with 32.768kHz int. osc. as reference Watchdog timer 560 A 1.0 Continuous mode 126 Sampled mode, includes ULP oscillator 1.2 BOD Internal 1.0V reference 89 Temperature sensor 83 3.0 ICC ADC DAC 250ksps VREF = Ext ref 250ksps VREF = Ext ref No load CURRLIMIT = LOW 2.6 CURRLIMIT = MEDIUM 2.1 CURRLIMIT = HIGH 1.6 Normal mode 1.9 Low Power mode 1.1 High speed mode 324 Low power mode 122 615KBps between I/O registers and SRAM 140 mA AC DMA Timer/counter USART 20 Rx and Tx enabled, 9600 BAUD Flash memory and EEPROM programming Note: 1. A 4 4 mA All parameters measured as the difference in current consumption between module enabled and disabled. All data at VCC = 3.0V, ClkSYS = 1MHz external clock without prescaling, T = 25C unless other conditions are given. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 99 37.2.4 Wake-up time from sleep modes Table 37-39. Device wake-up time from sleep modes with various system clock sources. Symbol Parameter Wake-up time from idle, standby, and extended standby mode twakeup Min. Typ.(1) External 2MHz clock 2.0 32.768kHz internal oscillator 120 2MHz internal oscillator 2.0 32MHz internal oscillator 0.2 External 2MHz clock 4.5 32.768kHz internal oscillator 320 2MHz internal oscillator 10 32MHz internal oscillator 5.5 Max. Units s Wake-up time from Power-save and Power-down mode Note: Condition 1. The wake-up time is the time from the wake-up request is given until the peripheral clock is available on pin, see Figure 37-9. All peripherals and modules start execution from the first clock cycle, expect the CPU that is halted for four clock cycles before program execution starts. Figure 37-9. Wake-up time definition. Wakeup time Wakeup request Clock output XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 100 37.2.5 I/O Pin Characteristics The I/O pins complies with the JEDEC LVTTL and LVCMOS specification and the high- and low level input and output voltage limits reflect or exceed this specification. Table 37-40. I/O pin characteristics. Symbol Parameter Condition Min. Typ. Max. Units -20 20 mA VCC = 2.7 - 3.6V 2 VCC+0.3 VCC = 2.0 - 2.7V 0.7*VCC VCC+0.3 VCC = 1.6 - 2.0V 0.7*VCC VCC+0.3 VCC = 2.7- 3.6V -0.3 0.3*VCC VCC = 2.0 - 2.7V -0.3 0.3*VCC VCC = 1.6 - 2.0V -0.3 0.3*VCC (1) IOH / IOL (2) I/O pin source/sink current VIH High level input voltage VIL Low level input voltage VCC = 3.0 - 3.6V IOH = -2mA 2.4 0.94*VCC IOH = -1mA 2.0 0.96*VCC IOH = -2mA 1.7 0.92*VCC VCC = 3.3V IOH = -8mA 2.6 2.9 VCC = 3.0V IOH = -6mA 2.1 2.6 VCC = 1.8V IOH = -2mA 1.4 1.6 VCC = 3.0 - 3.6V IOL = 2mA 0.05*VCC 0.4 IOL = 1mA 0.03*VCC 0.4 IOL = 2mA 0.06*VCC 0.7 VCC = 3.3V IOL = 15mA 0.4 0.76 VCC = 3.0V IOL = 10mA 0.3 0.64 VCC = 1.8V IOL = 5mA 0.3 0.46 <0.001 0.1 VCC = 2.3 - 2.7V VOH High level output voltage VCC = 2.3 - 2.7V VOL Low level output voltage IIN Input leakage current RP I/O pin Pull/Buss keeper resistor 25 Reset pin pull-up resistor 25 V A k RRST 4 tr Notes: Pad rise time No load ns slew rate limitation 1. 2. 7 The sum of all IOH for PORTA, PORTC, PORTD, PORTF, PORTH, PORTJ, PORTK must for each port not exceed 200mA. The sum of all IOH for PORTB must not exceed 100mA. The sum of all IOH for PORTQ, PORTR and PDI must not exceed 100mA. The sum of all IOL for PORTA, PORTC, PORTD, PORTF, PORTH, PORTJ, PORTK must for each port not exceed 200mA. The sum of all IOL for PORTB must not exceed 100mA. The sum of all IOL for PORTQ, PORTR and PDI must not exceed 100mA. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 101 37.2.6 ADC characteristics Table 37-41. Power supply, reference and input range. Symbol Parameter AVCC Analog supply voltage VREF Reference voltage Condition Min. Typ. Max. VCC- 0.3 VCC+ 0.3 1 AVCC- 0.6 Units V Rin Input resistance Switched 5.0 k Cin Input capacitance Switched 5.0 pF RAREF Reference input resistance (leakage only) >10 M CAREF Reference input capacitance Static load 7 pF VIN Input range Conversion range Differential mode, Vinp - Vinn VIN Conversion range Single ended unsigned mode, Vinp V Fixed offset voltage -0.1 AVCC+0.1 -VREF VREF -V VREF-V 190 V LSB Table 37-42. Clock and timing. Symbol ClkADC fclkADC Parameter Condition Min. Typ. Max. Units Maximum is 1/4 of peripheral clock frequency 100 Measuring internal signals 100 125 100 2000 Measuring internal signals 100 125 Sampling time 1/2 ClkADC cycle 0.25 5 s Conversion time (latency) (RES+2)/2+(GAIN !=0) RES (Resolution) = 12 5 8 ClkADC cycles Start-up time ADC clock cycles 12 24 After changing reference or input mode 7 7 After ADC flush 1 1 ADC clock frequency 2000 kHz Sample rate ksps ADC settling time XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 ClkADC cycles 102 Table 37-43. Accuracy characteristics. Symbol Parameter RES Resolution INL(1) DNL(1) Integral non-linearity Differential non-linearity Offset Error Condition(2) Programmable to 12-bit 1. 2. Max. Units 11 11.5 12 Bits VCC-1.0V < VREF< VCC-0.6V 1.2 2 All VREF 1.5 3 2000ksps, differential mode VCC-1.0V < VREF< VCC-0.6V 1.0 2 All VREF 1.5 3 single ended mode 1.5 4 guaranteed monotonic <0.5 <1 lsb -1 mV Temperature drift <0.01 mV/K Operating voltage drift <0.6 mV/V External reference -1 AVCC/1.6 10 AVCC/2.0 8 Bandgap 5 Gain Error Notes: Typ. 500ksps, differential mode Differential mode Noise Min. mV Temperature drift <0.02 mV/K Operating voltage drift <0.5 mV/V Differential mode, shorted input 2msps, VCC = 3.6V, ClkPER = 16MHz 0.4 mV rms Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% input voltage range. Unless otherwise noted all linearity, offset and gain error numbers are valid under the condition that external VREF is used. Table 37-44. Gain stage characteristics. Symbol Parameter Condition Min. Typ. Max. Units Rin Input resistance Switched in normal mode 4.0 k Csample Input capacitance Switched in normal mode 4.4 pF Signal range Gain stage output Propagation delay ADC conversion rate Sample rate Same as ADC INL(1) Integral Non-Linearity 500ksps 0 VCC- 0.6 ClkADC cycles 1 100 All gain settings 1.5 V 1000 kHz 3 lsb XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 103 Symbol Parameter Gain Error Offset Error, input referred Condition Min. 1x gain, normal mode -0.7 8x gain, normal mode -3.0 64x gain, normal mode -4.8 1x gain, normal mode 0.4 8x gain, normal mode 0.4 64x gain, normal mode 0.4 1x gain, normal mode Noise 8x gain, normal mode 1. Max. Units % mV 0.6 VCC = 3.6V mV rms 2.0 Ext. VREF 64x gain, normal mode Note: Typ. 11 Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% input voltage range. 37.2.7 DAC Characteristics Table 37-45. Power supply, reference and output range. Symbol Parameter AVCC Analog supply voltage AVREF External reference voltage Rchannel DC output impedance Condition Linear output voltage range RAREF CAREF Min. Max. VCC+ 0.3 1.0 VCC- 0.6 V 50 AVCC-0.15 V 0.15 Static load Minimum resistance load Units VCC- 0.3 Reference input resistance Reference input capacitance Typ. >10 M 7 pF 1 k 100 pF 1 nF AVCC/100 0 mA Maximum capacitance load 1000 serial resistance Operating within accuracy specification Output sink/source Safe operation 10 Table 37-46. Clock and timing. Symbol Fclk Parameter Conversion rate Condition Fout=Fclk/4, Cload=100pF, maximum step size Min. 0 Typ. Max. Units 1000 ksps XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 104 Table 37-47. Accuracy characteristics. Symbol RES Parameter Condition Min. Input resolution VREF= Ext 1.0V INL(1) Integral non-linearity VREF=AVCC VREF=INT1V VREF=Ext 1.0V DNL(1) Differential non-linearity VREF=AVCC VREF=INT1V Gain error Units 12 Bits 2.0 3 VCC = 3.6V 1.5 2.5 VCC = 1.6V 2.0 4 VCC = 3.6V 1.5 4 VCC = 1.6V 5.0 VCC = 3.6V 5.0 VCC = 1.6V 1.5 3.0 VCC = 3.6V 0.6 1.5 VCC = 1.6V 1.0 3.5 VCC = 3.6V 0.6 1.5 VCC = 1.6V 4.5 VCC = 3.6V 4.5 lsb After calibration <4 4 Gain calibration drift VREF= Ext 1.0V <0.2 mV/K Offset error After calibration <1 lsb Offset calibration step size 1. Max. VCC = 1.6V Gain calibration step size Note: Typ. 1 Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% output voltage range. 37.2.8 Analog Comparator Characteristics Table 37-48. Analog Comparator characteristics. Symbol Parameter Voff Input offset voltage Ilk Input leakage current Condition Input voltage range Vhys1 Hysteresis, none Vhys2 Hysteresis, small Vhys3 Hysteresis, large Min. Typ. Max. Units <10 mV <1 nA -0.1 AVCC +0.1 V 0 mode = High Speed (HS) 22 mode = Low Power (LP) 30 mode = HS 43 mode = LP 60 mV XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 105 Symbol Parameter Condition VCC = 3.0V, T= 85C tdelay Propagation delay Min. mode = HS mode = HS VCC = 3.0V, T= 85C Typ. Max. 60 90 60 mode = LP Units ns 130 Current source calibration range Single mode 2 8 Double mode 4 16 64-Level Voltage Scaler Integral non-linearity (INL) s 0.3 0.5 lsb 37.2.9 Bandgap and Internal 1.0V Reference Characteristics Table 37-49. Bandgap and Internal 1.0V reference characteristics. Symbol Parameter Condition Min. As reference for ADC or DAC Typ. Max. 1 ClkPER + 2.5s Startup time As input voltage to ADC and AC Units s 1.5 Bandgap voltage 1.1 V INT1V Internal 1.00V reference for ADC and DAC T= 85C, after calibration Variation over voltage and temperature Relative to T= 85C, VCC = 3.0V 0.99 1 1.01 1.0 % 37.2.10 Brownout Detection Characteristics Table 37-50. Brownout detection characteristics. Symbol Parameter Condition BOD level 0 falling VCC VBOT VHYST Typ. Max. 1.60 1.62 1.72 BOD level 1 falling VCC 1.8 BOD level 2 falling VCC 2.0 BOD level 3 falling VCC 2.2 BOD level 4 falling VCC 2.4 BOD level 5 falling VCC 2.6 BOD level 6 falling VCC 2.8 BOD level 7 falling VCC 3.0 0.4 Detection time s Sampled mode Hysteresis Units V Continuous mode tBOD Min. 1000 1.4 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 % 106 37.2.11 External Reset Characteristics Table 37-51. External reset characteristics. Symbol tEXT Parameter Condition Min. Typ. Max. Units 86 1000 ns Minimum reset pulse width Reset threshold voltage (VIH) VRST Reset threshold voltage (VIL) VCC = 2.7 - 3.6V 0.60*VCC VCC = 1.6 - 2.7V 0.60*VCC VCC = 2.7 - 3.6V 0.40*VCC VCC = 1.6 - 2.7V 0.40*VCC V 37.2.12 Power-on Reset Characteristics Table 37-52. Power-on reset characteristics. Symbol Parameter VPOT- (1) POR threshold voltage falling VCC VPOT+ POR threshold voltage rising VCC Note: 1. Condition Min. Typ. VCC falls faster than 1V/ms 0.4 1.0 VCC falls at 1V/ms or slower 0.8 1.0 Max. Units V 1.3 1.59 Typ. Max. VPOT- values are only valid when BOD is disabled. When BOD is enabled VPOT- = VPOT+. 37.2.13 Flash and EEPROM Memory Characteristics Table 37-53. Endurance and data retention. Symbol Parameter Condition Min. 25C 10K 85C 10K 25C 100 55C 25 25C 80K 85C 30K 25C 100 55C 25 Write/Erase cycles Units Cycle Flash Data retention Year Write/Erase cycles Cycle EEPROM Data retention Year XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 107 Table 37-54. Programming time. Symbol Parameter Chip Erase Flash EEPROM Notes: 1. 2. Condition Min. Typ. (1) 128KB Flash, EEPROM(2) and SRAM Erase 75 Page Erase 4 Page Write 4 Atomic Page Erase and Write 8 Page Erase 4 Page Write 4 Atomic Page Erase and Write 8 Max. Units ms Programming is timed from the 2MHz internal oscillator. EEPROM is not erased if the EESAVE fuse is programmed. 37.2.14 Clock and Oscillator Characteristics 37.2.14.1 Calibrated 32.768kHz Internal Oscillator characteristics Table 37-55. 32.768kHz internal oscillator characteristics. Symbol Parameter Condition Min. Frequency Factory calibration accuracy Typ. Max. 32.768 T = 85C, VCC = 3.0V User calibration accuracy Units kHz -0.5 0.5 -0.5 0.5 % 37.2.14.2 Calibrated 2MHz RC Internal Oscillator characteristics Table 37-56. 2MHz internal oscillator characteristics. Symbol Parameter Tunable frequency range Condition Min. DFLL can tune to this frequency over voltage and temperature 1.8 Typ. Max. Units 2.2 MHz Factory calibrated frequency 2.0 Factory calibration accuracy T = 85C, VCC= 3.0V DFLL calibration stepsize T = 25C, VCC= 3.0V -1.5 1.5 % 0.23 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 108 37.2.14.3 Calibrated and tunable 32MHz internal oscillator characteristics Table 37-57. 32MHz internal oscillator characteristics. Symbol Parameter Tunable frequency range Condition Min. DFLL can tune to this frequency over voltage and temperature 30 Max. Units 35 MHz Factory calibrated frequency Factory calibration accuracy Typ. 32 T = 85C, VCC= 3.0V -1.5 1.5 % DFLL calibration step size 0.24 37.2.14.4 32kHz Internal ULP Oscillator characteristics Table 37-58. 32kHz internal ULP oscillator characteristics. Symbol Parameter Condition Min. Output frequency Typ. Max. 32 Accuracy -30 Units kHz 30 % Max. Units 37.2.14.5 Internal Phase Locked Loop (PLL) characteristics Table 37-59. Internal PLL characteristics. Symbol fIN Parameter Input frequency Output frequency(1) fOUT Condition Output frequency must be within fOUT 1. Typ. TBD VCC= 1.6 20 32 VCC= 2.7 20 96 VCC= 3.6V 20 128 Duty cycle Note: Min. MHz 50 Start-up lock time fOUT = 48MHz 18 Re-lock time fOUT-init = 10MHz, fOUT-end = 64MHz 17 % s The maximum output frequency vs. supply voltage is linear between 1.8V and 2.7V, and can never be higher than four times the maximum CPU frequency. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 109 37.2.14.6 External clock characteristics Figure 37-10.External clock drive waveform. tCH tCH tCF tCR VIH1 VIL1 tCL tCK Table 37-60. External clock(1). Symbol Parameter Clock frequency(2) 1/tCK tCK Clock period tCH/CL Clock high/low time VIL/IH Low/high level input voltage tCK Reduction in period from one clock cycle to the next Notes: 1. 2. Condition Min. Typ. Max. VCC = 1.6 - 1.8V 90 VCC = 2.7 - 3.6V 142 Units MHz VCC = 1.6 - 1.8V 11 VCC = 2.7 - 3.6V 7 VCC = 1.6 - 1.8V 4.5 VCC = 2.7 - 3.6V 2.4 ns See Table 37-7 on page 79 V 10 % System Clock Prescalers must be set so that maximum CPU clock frequency for device is not exceeded. The maximum frequency vs. supply voltage is linear between 1.8V and 2.7V, and the same applies for all other parameters with supply voltage conditions. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 110 37.2.14.7 External 16MHz crystal oscillator and XOSC characteristics Table 37-61. External 16MHz crystal oscillator and XOSC characteristics. . Symbol Parameter Condition Min. Typ. FRQRANGE=0 <10 FRQRANGE=1, 2, 3 <1 Max. Cycle to cycle jitter Units ns FRQRANGE=0 <0.5 FRQRANGE=1 <0.05 FRQRANGE=2 <0.005 FRQRANGE=3 <0.005 FRQRANGE=0 50 FRQRANGE=1 50 FRQRANGE=2 50 FRQRANGE=3 50 Frequency error % Duty cycle FRQRANGE=0 FRQRANGE=1 RQ Negative impedance(1) FRQRANGE=2 FRQRANGE=3 ESR SF = safety factor 0.4MHz resonator, CL=100pF 13k 1MHz crystal, CL=20pF 9k 2MHz crystal, CL=20pF 2.2k 1MHz crystal, CL=20pF 2.3k 2MHz crystal, CL=20pF 8k 9MHz crystal, CL=20pF 200 8MHz crystal, CL=20pF 225 9MHz crystal, CL=20pF 300 12MHz crystal, CL=10pF 175 8MHz crystal, CL=20pF 340 9MHz crystal, CL=20pF 400 12MHz crystal, CL=10pF 330 12MHz crystal, CL=12pF 230 16MHz crystal, CL=10pF 115 min(RQ)/SF XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 k 111 Symbol Parameter Condition Start-up time Min. Typ. XOSCPWR=0, FRQRANGE=0 0.4MHz resonator, CL=100pF 1.0 XOSCPWR=0, FRQRANGE=1 2MHz crystal, CL=20pF 2.6 XOSCPWR=0, FRQRANGE=2 8MHz crystal, CL=20pF 0.8 XOSCPWR=0, FRQRANGE=3 12MHz crystal, CL=20pF 1.0 XOSCPWR=1, FRQRANGE=3 16MHz crystal, CL=20pF 1.4 CXTAL1 Parasitic capacitance XTAL1 pin 6 CXTAL2 Parasitic capacitance XTAL2 pin 10 CLOAD Parasitic capacitance load 3.8 Note: 1. Max. Units ms pF Numbers for negative impedance are not tested in production but guaranteed from design and characterization. 37.2.14.8 External 32.768kHz crystal oscillator and TOSC characteristics Table 37-62. External 32.768kHz crystal oscillator and TOSC characteristics. Symbol Parameter Condition ESR/R1 Recommended crystal equivalent series resistance (ESR) Min. Typ. Crystal load capacitance 6.5pF 60 Crystal load capacitance 9.0pF 35 Parasitic capacitance TOSC1 pin 4.0 CTOSC2 Parasitic capacitance TOSC2 pin 4.1 Parasitic capacitance load 2.0 Recommended safety factor Note: 1. Units k CTOSC1 CL Max. Capacitive load matched to crystal specification pF 3 See Figure 37-11 for definition. Figure 37-11.TOSC input capacitance. CL1 TOSC1 CL2 Device internal External TOSC2 32.768kHz crystal XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 112 The parasitic capacitance between the TOSC pins is CL1 + CL2 in series as seen from the crystal when oscillating without external capacitors. 37.2.15 SPI Characteristics Figure 37-12.SPI timing requirements in master mode. SS tSCKR tMOS tSCKF SCK (CPOL = 0) tSCKW SCK (CPOL = 1) tSCKW tMIS MISO (Data Input) tMIH tSCK MSB LSB tMOH tMOH MOSI (Data Output) MSB LSB Figure 37-13.SPI timing requirements in slave mode. SS tSSS tSCKR tSCKF tSSH SCK (CPOL = 0) tSSCKW SCK (CPOL = 1) tSSCKW tSIS MOSI (Data Input) tSIH MSB tSOSSS MISO (Data Output) tSSCK LSB tSOS MSB tSOSSH LSB XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 113 Table 37-63. SPI timing characteristics and requirements. Symbol Parameter tSCK SCK period Master (See Table 21-4 in XMEGA AU Manual) tSCKW SCK high/low width Master 0.5*SCK tSCKR SCK rise time Master 2.7 tSCKF SCK fall time Master 2.7 tMIS MISO setup to SCK Master 11 tMIH MISO hold after SCK Master 0 tMOS MOSI setup SCK Master 0.5*SCK MOSI hold after SCK Master 1 SCK to out high Master 1 Slave SCK period Slave 4*tClkPER tSSCKW SCK high/low width Slave 2*tClkPER tSSCKR SCK rise time Slave 1600 tSSCKF SCK fall time Slave 1600 tSIS MOSI setup to SCK Slave 3 tSIH MOSI hold after SCK Slave tSCK tSSS SS setup to SCK Slave 20 tSSH SS hold after SCK Slave 20 tSOS MISO setup SCK Slave 8 tSOH MISO hold after SCK Slave 13 tSOSS MISO setup after SS low Slave 11 tSOSH MISO hold after SS high Slave 8 tMOH tSSCK Condition Min. Typ. Max. Units ns XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 114 37.2.16 EBI characteristics Table 37-64. EBI SRAM characteristics and requirements. Symbol Parameter tClkPER2 SRAM clock period Condition Min. Typ. Max. Units 0.5*tClkPER tALH SRAM address hold after ALE low tClkPER2 tALS SRAM address setup before ALE low (read and write) tClkPER2 tALW SRAM ALE width tClkPER2 tARH SRAM address hold after RE high tClkPER2 tARS SRAM address setup before RE high tClkPER2 tAWH SRAM address hold after WE high tClkPER2 tAWS SRAM Address setup before WE high tClkPER2 tDRH SRAM data hold after RE high tDRS SRAM data setup to RE high 3.0V tDRS SRAM data setup to RE high 2.7V, 85C 17 tDRS SRAM data setup to RE high 1.6V, 85C 27 tDWH SRAM data hold after WE high tClkPER2 tDWS SRAM data setup to WE high tClkPER2 tRW SRAM read enable pulse width tClkPER2*SRWS tWW SRAM write enable pulse width tClkPER2*SRWS tCH SRAM chip select hold after RE/WE high tCRS SRAM chip select setup to RE low or ALE high tCWS SRAM chip select setup to WE low (no ALE) 0 12 ns tClkPER2 0 tClkPER2 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 115 Table 37-65. EBI SDRAM characteristics and requirements. Symbol Parameter Condition tClkPER2 SDRAM clock period Min. Typ. Max. Units 0.5*tClkPER tAH SDRAM address hold time 0.5*tClkPER2 tAS SDRAM address setup time 0.5*tClkPER2 tCH SDRAM clock high-level width 0.5*tClkPER2 tCL SDRAM clock low-level width 0.5*tClkPER2 tCKH SDRAM CKE hold time 0.5*tClkPER2 tCKS SDRAM CKE setup time 0.5*tClkPER2 tCMH SDRAM CS, RAS, CAS, WE, DQM hold time 0.5*tClkPER2 tCMS SDRAM CS, RAS, CAS, WE, DQM setup time 0.5*tClkPER2 tDRH SDRAM data in hold after CLK high tAC SDRAM access time from CLK ns 0 tClkPER-5 tDWH SDRAM data out hold after CLK high 0.5*tClkPER2 tDWS SDRAM data out setup before CLK high 0.5*tClkPER2 37.2.17 Two-Wire Interface Characteristics Table 37-66 on page 117 describes the requirements for devices connected to the Two-Wire Interface Bus. The Atmel AVR XMEGA Two-Wire Interface meets or exceeds these requirements under the noted conditions. Timing symbols refer to Figure 37-14. Figure 37-14.Two-Wire Interface bus timing. tof tHIGH tLOW tr SCL tSU;STA tHD;DAT tHD;STA tSU;DAT tSU;STO SDA tBUF XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 116 Table 37-66. Two-wire interface characteristics. Symbol Parameter Condition Min. Typ. Max. Units VIH Input high voltage 0.7*VCC VCC+0.5 VIL Input low voltage -0.5 0.3*VCC Vhys Hysteresis of Schmitt trigger inputs 0.05*VCC (1) 0 0 0.4 20+0.1Cb (1)(2) 0 20+0.1Cb (1)(2) 300 0 50 -10 10 A 10 pF 400 kHz VOL Output low voltage tr Rise time for both SDA and SCL tof Output fall time from VIHmin to VILmax tSP Spikes suppressed by input filter II Input current for each I/O pin CI Capacitance for each I/O pin fSCL SCL clock frequency 3mA, sink current 10pF < Cb < 400pF (2) 0.1VCC < VI < 0.9VCC fPER (3)>max(10fSCL, 250kHz) 0 fSCL 100kHz RP Value of pull-up resistor fSCL > 100kHz tHD;STA Hold time (repeated) START condition tLOW Low period of SCL clock tHIGH High period of SCL clock tSU;STA Set-up time for a repeated START condition tHD;DAT Data hold time tSU;DAT Data setup time tSU;STO Setup time for STOP condition Bus free time between a STOP and START condition tBUF Notes: 1. 2. 3. V CC - 0.4V ---------------------------3mA 100ns --------------Cb 300ns --------------Cb fSCL 100kHz 4.0 fSCL > 100kHz 0.6 fSCL 100kHz 4.7 fSCL > 100kHz 1.3 fSCL 100kHz 4.0 fSCL > 100kHz 0.6 fSCL 100kHz 4.7 fSCL > 100kHz 0.6 fSCL 100kHz 0 3.5 fSCL > 100kHz 0 0.9 fSCL 100kHz 250 fSCL > 100kHz 100 fSCL 100kHz 4.0 fSCL > 100kHz 0.6 fSCL 100kHz 4.7 fSCL > 100kHz 1.3 V ns s s Required only for fSCL > 100kHz. Cb = Capacitance of one bus line in pF. fPER = Peripheral clock frequency. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 117 38. Typical Characteristics 38.1 ATxmega64A1U 38.1.1 Current consumption 38.1.1.1 Active mode supply current Figure 38-1. Active supply current vs. frequency. fSYS = 0 - 1MHz external clock, T = 25C. ICC [A] 800 3.3V 700 3.0V 600 2.7V 500 2.2V 400 1.8V 300 200 100 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Frequency [MHz] Figure 38-2. Active supply current vs. frequency. fSYS = 1 - 32MHz external clock, T = 25C. 18 3.3 V 16 3.0 V 14 2.7 V ICC [mA] 12 10 2.2 V 8 6 4 1.8 V 2 0 0 4 8 12 16 20 24 28 32 Frequency [MHz] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 118 Figure 38-3. Active mode supply current vs. VCC. fSYS = 32.768kHz internal oscillator. 185 -40C 170 155 25C ICC [A] 140 85C 125 110 95 80 65 50 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] Figure 38-4. Active mode supply current vs. VCC. fSYS = 1MHz external clock. 900 -40C 25C 85C 800 ICC [A] 700 600 500 400 300 200 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 119 Figure 38-5. Active mode supply current vs. VCC. fSYS = 2MHz internal oscillator. 1800 -40C 25C 85C 1650 ICC [A] 1500 1350 1200 1050 900 750 600 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] Figure 38-6. Active mode supply current vs. VCC. fSYS = 32MHz internal oscillator prescaled to 8MHz. 8 -40 C 25 C 85 C 7 ICC [mA] 6 5 4 3 2 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 120 Figure 38-7. Active mode supply current vs. VCC. fSYS = 32MHz internal oscillator. 21 -40C 20 25C 85C ICC [mA] 19 18 17 16 15 14 13 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 VCC [V] 38.1.1.2 Idle mode supply current Figure 38-8. Idle mode supply current vs. frequency. fSYS = 0 - 1MHz external clock, T = 25C. ICC [A] 250 225 3.3 V 200 3.0 V 175 2.7 V 150 2.2 V 125 1.8 V 100 75 50 25 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Frequency [MHz] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 121 Figure 38-9. Idle mode supply current vs. frequency. fSYS = 1 - 32MHz external clock, T = 25C. 8 3.3 V 7 3.0 V ICC [mA] 6 2.7 V 5 4 2.2 V 3 2 1.8 V 1 0 0 4 8 12 16 20 24 28 32 Frequency [MHz] Figure 38-10.Idle mode supply current vs. VCC. fSYS = 32.768kHz internal oscillator. 37 36 85C -40C 35 25C ICC [A] 34 33 32 31 30 29 28 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 122 Figure 38-11.Idle mode supply current vs. VCC. fSYS = 1MHz external clock. 270 85 C 25 C -40 C 250 230 ICC [A] 210 190 170 150 130 110 90 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-12.Idle mode supply current vs. VCC. fSYS = 2MHz internal oscillator. -40 C 25 C 85 C 600 550 ICC [A] 500 450 400 350 300 250 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 123 Figure 38-13.Idle mode supply current vs. VCC. fSYS = 32MHz internal oscillator prescaled to 8MHz. 3100 -40 C 25 C 85 C 2800 ICC [A] 2500 2200 1900 1600 1300 1000 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-14.Idle mode current vs. VCC. fSYS = 32MHz internal oscillator. 8650 -40 C 25 C 85 C 8300 7950 ICC [uA] 7600 7250 6900 6550 6200 5850 5500 2.7 2.8 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 124 38.1.1.3 Power-down mode supply current Figure 38-15.Power-down mode supply current vs. Temperature. All functions disabled. 1.6 3.3V 3.0V 2.7V 2.2V 1.8V 1.4 ICC [A] 1.2 1.0 0.8 0.6 0.4 0.2 0 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 Temperature [C] Figure 38-16.Power-down mode supply current vs. Temperature. Sampled BOD with Watchdog Timer running on ULP oscillator. 2.8 3.3V 3.0V 2.7V 2.2V 1.8V 2.6 2.4 ICC [A] 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 125 38.1.1.4 Power-save mode supply current Figure 38-17.Power-save mode supply current vs. VCC. Real Time Counter enabled and running from 1.024kHz output of 32.768kHz TOSC. 0.90 0.85 Normal mode ICC [A] 0.80 0.75 0.70 0.65 Low-power mode 0.60 0.55 0.50 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] 38.1.1.5 Standby mode supply current Figure 38-18.Standby supply current vs. VCC. Standby, fSYS = 1MHz. 9.5 85C 9.0 8.5 25C -40C 8.0 7.5 ICC [A] 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 126 Figure 38-19.Standby supply current vs. VCC. 25C, running from different crystal oscillators. 500 16MHz 12MHz 450 ICC [A] 400 350 8MHz 2MHz 300 250 0.454MHz 200 150 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] 38.1.2 I/O Pin Characteristics 38.1.2.1 Pull-up Figure 38-20.I/O pin pull-up resistor current vs. pin voltage. VCC = 1.8V. 80 70 60 IPIN [A] 50 40 30 20 -40C 25C 85C 10 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 VPIN [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 127 Figure 38-21.I/O pin pull-up resistor current vs. pin voltage. VCC = 3.0V. 120 105 90 IPIN [A] 75 60 45 30 -40C 25C 85C 15 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VPIN [V] Figure 38-22.I/O pin pull-up resistor current vs. pin voltage. VCC = 3.3V. 140 120 IPIN [A] 100 80 60 40 -40C 25C 85C 20 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 VPIN [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 128 38.1.2.2 Output Voltage vs. Sink/Source Current Figure 38-23.I/O pin output voltage vs. source current. VCC = 1.8V. 1.85 1.70 1.55 VPIN [V] 1.40 1.25 1.10 -40C 0.95 25C 0.80 0.65 85C 0.50 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 -12 -9 -6 -3 0 IPIN [mA] Figure 38-24.I/O pin output voltage vs. source current. VCC = 3.0V. 3.2 2.9 2.6 VPIN [V] 2.3 2.0 1.7 -40C 1.4 25C 1.1 85C 0.8 0.5 -30 -27 -24 -21 -18 -15 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 129 Figure 38-25.I/O pin output voltage vs. source current. VCC = 3.3V. 3.5 3.2 2.9 VPIN [V] 2.6 2.3 2.0 -40C 1.7 1.4 25C 1.1 85C 0.8 0.5 -30 -27 -24 -21 -18 -15 -12 -9 -6 -3 0 IPIN [mA] Figure 38-26.I/O pin output voltage vs. source current. 3.8 3.6V 3.4 3.3V VPIN [V] 3.0 2.7V 2.6 2.2 1.8V 1.8 1.4 1.0 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 130 Figure 38-27.I/O pin output voltage vs. sink current. VCC = 1.8V. 1.0 85C 0.9 25C 0.8 VPIN [V] 0.7 -40C 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 2 4 6 8 10 12 14 16 IPIN [mA] Figure 38-28.I/O pin output voltage vs. sink current. VCC = 3.0V. 1.0 85C 0.9 25C 0.8 -40C VPIN [V] 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 3 6 9 12 15 18 21 24 27 30 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 131 Figure 38-29.I/O pin output voltage vs. sink current. VCC = 3.3V. 1.0 85C 0.9 25C -40C 0.8 VPIN [V] 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 1 4 7 10 13 16 19 22 25 28 31 IPIN [mA] Figure 38-30.I/O pin output voltage vs. sink current. 1.50 1.8V 1.35 1.20 VPIN [V] 1.05 0.90 2.7V 3.3V 3.6V 0.75 0.60 0.45 0.30 0.15 0.00 5 7 9 11 13 15 17 19 21 23 25 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 132 38.1.2.3 Thresholds and Hysteresis Figure 38-31.I/O pin input threshold voltage vs. VCC. T = 25C. 1.85 VIH 1.70 VIL Vthreshold [V] 1.55 1.40 1.25 1.10 0.95 0.80 0.65 0.50 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-32.I/O pin input threshold voltage vs. VCC. VIH I/O pin read as "1". 1.88 -40C 25C 85C 1.76 Vthreshold[V] 1.64 1.52 1.4 1.28 1.16 1.04 0.92 0.8 1.6 1.85 2.1 2.35 2.6 2.85 3.1 3.35 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 133 Figure 38-33.I/O pin input threshold voltage vs. VCC. VIL I/O pin read as "0". 1.70 -40 C 25 C 85 C 1.55 Vthreshold [V] 1.40 1.25 1.10 0.95 0.80 0.65 0.50 1.6 1.85 2.1 2.35 2.6 2.85 3.1 3.35 3.6 VCC [V] Figure 38-34.I/O pin input hysteresis vs. VCC. 0.36 -40C 0.33 Vhyst [V] 0.3 0.27 25C 0.24 0.21 85C 0.18 0.15 0.12 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 134 38.1.3 ADC Characteristics Figure 38-35.INL error vs. external VREF. T = 25C, VCC = 3.6V, external reference. 1.6 1.5 Single-ended unsigned mode INL [LSB] 1.4 1.3 Differential mode 1.2 1.1 1 Single-ended signed mode 0.9 0.8 0.7 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 1850 2000 VREF [V] Figure 38-36.INL error vs. sample rate. T = 25C, VCC = 3.6V, VREF = 2.0V external. 1.17 1.14 Differential mode 1.11 Single-ended Unsigned mode INL [LSB] 1.08 1.05 1.02 Single-ended Signed mode 0.99 0.96 0.93 0.9 500 650 800 950 1100 1250 1400 1550 1700 ADC Sample rate [ksps] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 135 Figure 38-37.INL error vs. input code 2 1.5 INL [LSB] 1 0.5 0 -0.5 -1 -1.5 -2 0 512 1024 1536 2048 2560 3072 3584 4096 ADC input code Figure 38-38.DNL error vs. external VREF. T = 25C, VCC = 3.6V, external reference. 1.3 1.2 Single-ended unsigned mode 1.1 DNL [LSB] 1 0.9 0.8 0.7 0.6 Differential mode 0.5 0.4 Single-ended signed mode 0.3 0.2 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 136 Figure 38-39.DNL error vs. sample rate. T = 25C, VCC = 3.6V, VREF = 2.0V external. 0.53 0.51 Differential mode DNL [LSB] 0.49 0.47 Single-ended signed mode 0.45 0.43 0.41 0.39 Single-ended unsigned mode 0.37 0.35 500 650 800 950 1100 1250 1400 1550 1700 1850 2000 ADC sample rate [ksps] Figure 38-40.DNL error vs. input code. 0.7 0.6 DNL [LSB] 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 0 512 1024 1536 2048 2560 3072 3584 4096 ADC input code XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 137 Figure 38-41.Gain error vs. VREF. T = 25C, VCC = 3.6V, ADC sampling speed = 500ksps. 10 9 Single-ended signed mode Gain Error [mV] 8 7 6 5 Single-ended unsigned mode 4 3 2 Differential mode 1 0 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] Figure 38-42.Gain error vs. VCC. T = 25C, VREF = external 1.0V, ADC sampling speed = 500ksps. 9 8 Single-ended signed mode Gain error [mV] 7 6 5 4 Single-ended unsigned mode 3 2 Differential mode 1 0 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 138 Figure 38-43.ADC Offset error vs. VREF. T = 25C, VCC = 3.6V, ADC sampling speed = 500ksps. -0.8 -0.85 Offset [mV] -0.9 -0.95 -1 -1.05 Differential mode -1.1 -1.15 -1.2 -1.25 -1.3 -1.35 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] Figure 38-44.Gain error vs. temperature. VCC = 3.0V, VREF = external 2.0V. 11 10 Single-ended Signed Gain Error [mV] 9 8 7 6 5 Single-ended Unsigned 4 3 Differential 2 1 0 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 139 Figure 38-45.ADC Offset vs. VCC. T = 25C, VREF = external 1.0V, ADC sampling speed = 500ksps. -0.2 -0.25 Offset [mV] -0.3 -0.35 Differential mode -0.4 -0.45 -0.5 -0.55 -0.6 -0.65 -0.7 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-46.Noise vs. VREF. T = 25C, VCC = 3.6V, ADC sampling speed = 500ksps. 0.47 0.46 Differential Noise [mV RMS] 0.45 0.44 0.43 0.42 0.41 0.4 0.39 0.38 0.37 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 140 Figure 38-47.Noise vs. VCC. T = 25C, VREF = external 1.0V, ADC sampling speed = 500ksps. 0.42 Noise [mV RMS] 0.41 Differential 0.4 0.39 0.38 0.37 0.36 0.35 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] 38.1.4 DAC Characteristics Figure 38-48.DAC INL error vs. VREF. VCC = 3.6V, external reference, room temperature. 1.9 1.8 INL [LSB] 1.7 1.6 1.5 1.4 1.3 1.2 1.1 25C 1 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 141 Figure 38-49.DAC DNL error vs. VREF. VCC = 3.6V, external reference, room temperature. 1.35 1.25 DNL [LSB] 1.15 1.05 0.95 0.85 0.75 0.65 25C 0.55 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] Figure 38-50.DAC noise vs. temperature. VCC = 3.0V, VREF = 2.4V . 0.183 0.181 Noise [mV RMS] 0.179 0.177 0.175 0.173 0.171 0.169 0.167 0.165 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 142 38.1.5 Analog Comparator Characteristics Figure 38-51.Analog comparator hysteresis vs. VCC. High-speed, small hysteresis. 27 26 25C 85C -40C 25 VHYST [mV] 24 23 22 21 20 19 18 17 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-52.Analog comparator hysteresis vs. VCC. Low power, small hysteresis. 35 85C 34 33 VHYST [mV] 32 31 25C 30 29 -40C 28 27 26 25 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 143 Figure 38-53.Analog comparator hysteresis vs. VCC. High-speed mode, large hysteresis. 53 51 85C 25C -40C VHYST [mV] 49 47 45 43 41 39 37 35 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-54.Analog comparator hysteresis vs. VCC. Low power, large hysteresis. 74 85C 71 VHYST [mV] 68 65 25C 62 59 -40C 56 53 50 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 144 Figure 38-55.Analog comparator current source vs. calibration value. Temperature = 25C. 8 7 I [A] 6 5 3.3V 3.0V 2.7V 4 3 2.2V 1.8V 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CALIB[3..0] Figure 38-56.Analog comparator current source vs. calibration value. VCC = 3.0V. 6.0 5.7 5.4 I [A] 5.1 4.8 4.5 4.2 3.9 3.6 -40C 25C 85C 3.3 3.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CALIB[3..0] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 145 Figure 38-57.Voltage scaler INL vs. SCALEFAC. T = 25C, VCC = 3.0V. 0.30 0.25 INL [LSB] 0.20 0.15 0.10 0.05 25C 0.00 -0.05 -0.10 0 7 14 21 28 35 42 49 56 63 SCALEFAC 38.1.6 Internal 1.0V reference Characteristics Figure 38-58. ADC/DAC Internal 1.0V reference vs. temperature. 1.005 1.8V 2.7V 3.0V 3.3V Bandgap Voltage [V] 1.002 0.999 0.996 0.993 0.99 0.987 0.984 0.981 0.978 0.975 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 146 38.1.7 BOD Characteristics Figure 38-59.BOD thresholds vs. temperature. BOD level = 1.6V. 1.65 Rising Vcc 1.64 Falling Vcc VBOT [V] 1.63 1.62 1.61 1.60 1.59 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] Figure 38-60.BOD thresholds vs. temperature. BOD level = 3.0V. 3.090 Rising Vcc 3.075 3.060 VBOT [V] 3.045 Falling Vcc 3.030 3.015 3.000 2.985 2.970 2.955 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 147 38.1.8 External Reset Characteristics Figure 38-61.Minimum Reset pin pulse width vs. VCC. 120 110 tRST [ns] 100 90 25C -40C 80 70 85C 60 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-62.Reset pin pull-up resistor current vs. reset pin voltage. VCC = 1.8V. 80 -40C 70 25C IRESET[uA] 60 85C 50 40 30 20 10 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 VRESET [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 148 Figure 38-63.Reset pin pull-up resistor current vs. reset pin voltage. VCC = 3.0V. 135 -40C 120 25C IRESET [A] 105 85C 90 75 60 45 30 15 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 2.80 3.15 3.50 VRESET [V] Figure 38-64.Reset pin pull-up resistor current vs. reset pin voltage. VCC = 3.3V. IRESET [A] 160 140 -40C 25C 120 85C 100 80 60 40 20 0 0.00 0.35 0.70 1.05 1.40 1.75 2.10 2.45 VRESET [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 149 Figure 38-65.Reset pin input threshold voltage vs. VCC. VIH - Reset pin read as "1". 2.20 -40C 25C 85C 2.05 Vthreshold [V] 1.90 1.75 1.60 1.45 1.30 1.15 1.00 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-66.Reset pin input threshold voltage vs. VCC. VIL - Reset pin read as "0". 1.85 -40C 25C 85C 1.70 1.55 Vthreshold [V] 1.40 1.25 1.10 0.95 0.80 0.65 0.50 0.35 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 150 38.1.9 Power-on Reset Characteristics Figure 38-67.Power-on reset current consumption vs. VCC. BOD level = 3.0V, enabled in continuous mode. 1500 1350 -40C 1200 25C 85C ICC [A] 1050 900 750 600 450 300 150 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VCC [V] Figure 38-68.Power-on reset current consumption vs. VCC. BOD level = 3.0V, enabled in sampled mode. 1350 -40C 1200 25C 1050 85C ICC [A] 900 750 600 450 300 150 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 151 38.1.10 Oscillator Characteristics 38.1.10.1 Ultra Low-Power internal oscillator Figure 38-69.Ultra Low-Power internal oscillator frequency vs. temperature. 30.0 29.7 Frequency [kHz] 29.4 29.1 28.8 28.5 3.3V 3.0V 2.7V 2.2V 1.8V 28.2 27.9 27.6 27.3 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] 38.1.10.2 32.768kHz Internal Oscillator Figure 38-70. 32.768kHz internal oscillator frequency vs. temperature. 32.775 1.8V Frequency [kHz] 32.750 2.2V 2.7V 3.0V 3.3V 32.725 32.700 32.675 32.650 32.625 32.600 32.575 32.550 32.525 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 152 Figure 38-71. 32.768kHz internal oscillator frequency vs. calibration value. VCC = 3.0V, T = 25C. 50 47 Frequency [kHz] 44 41 38 35 32 29 26 23 20 0 30 60 90 120 150 180 210 240 270 RC32KCAL[7..0] 38.1.10.3 2MHz Internal Oscillator Figure 38-72. 2MHz internal oscillator frequency vs. temperature. DFLL disabled. 2.07 Frequency [MHz] 2.06 2.05 2.04 2.03 2.02 3.3V 3.0V 2.7V 2.2V 1.8V 2.01 2.00 1.99 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 153 Figure 38-73. 2MHz internal oscillator frequency vs. temperature. DFLL enabled. 2.0040 Frequency [MHz] 2.0025 1.8V 2.0010 2.2V 2.7V 3.0V 3.3V 1.9995 1.9980 1.9965 1.9950 1.9935 1.9920 1.9905 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] Figure 38-74. 2MHz internal oscillator CALA calibration step size. VCC = 3V. Frequency Step size [%] 0.24 0.23 0.21 0.20 0.18 0.17 0.15 -40C 85C 25C 0.14 0.12 0 15 30 45 60 75 90 105 120 135 CALA XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 154 38.1.10.4 32MHz Internal Oscillator Figure 38-75. 32MHz internal oscillator frequency vs. temperature. DFLL disabled. 34.2 Frequency [MHz] 33.9 33.6 33.3 33.0 32.7 32.4 3.3V 3.0V 2.7V 2.2V 1.8V 32.1 31.8 31.5 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] Figure 38-76. 32MHz internal oscillator frequency vs. temperature. DFLL enabled, from the 32.768kHz internal oscillator. Frequency [MHz] 32.01 31.98 1.8V 2.2V 31.95 3.3V 3.0V 31.92 2.7V 31.89 31.86 31.83 31.80 31.77 31.74 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 155 Figure 38-77. 32MHz internal oscillator CALA calibration step size. VCC = 3.0V. 0.30 Frequency Step size [%] 0.28 0.26 0.24 0.22 0.20 85C 25C -40C 0.18 0.16 0.14 0.12 0.10 0 15 30 45 60 75 90 105 120 135 CALA Figure 38-78. 32MHz internal oscillator frequency vs. CALB calibration value. VCC = 3.0V, DFLL disabled. 75 -40C 25C 85C 70 Frequency [MHz] 65 60 55 50 45 40 35 30 25 0 8 16 24 32 40 48 56 64 CALB XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 156 38.1.10.5 32MHz internal oscillator calibrated to 48MHz Figure 38-79. 48MHz internal oscillator frequency vs. temperature. DFLL disabled. 51.50 Frequency [MHz] 51.00 50.50 50.00 49.50 49.00 48.50 3.3V 3.0V 2.7V 2.2V 1.8V 48.00 47.50 47.00 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] Figure 38-80. 48MHz internal oscillator frequency vs. temperature. DFLL enabled, from the 32.768kHz internal oscillator. 48.05 1.8V 2.2V 3.0V 2.7V 3.3V Frequency [MHz] 48.00 47.95 47.90 47.85 47.80 47.75 47.70 47.65 47.60 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 157 Figure 38-81. 32MHz internal oscillator CALA calibration step size. Using 48MHz calibration value from signature row, VCC = 3.0V. 0.30 Frequency Step size [%] 0.28 0.26 0.24 0.22 0.20 25C -40C 85C 0.18 0.16 0.14 0.12 0.10 0 15 30 45 60 75 90 105 120 135 CALA 38.1.11 PDI characteristics Figure 38-82.Maximum PDI frequency vs. VCC. 34 -40C 25C 85C 31 fMAX [MHz] 28 25 22 19 16 13 10 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 158 38.2 ATxmega128A1U 38.2.1 Current consumption 38.2.1.1 Active mode supply current Figure 38-83.Active supply current vs. frequency. fSYS = 0 - 1MHz external clock, T = 25C. ICC [A] 800 3.3V 700 3.0V 600 2.7V 500 2.2V 400 1.8V 300 200 100 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Frequency [MHz] Figure 38-84.Active supply current vs. frequency. fSYS = 1 - 32MHz external clock, T = 25C. 18 3.3 V 16 3.0 V 14 2.7 V ICC [mA] 12 10 2.2 V 8 6 4 1.8 V 2 0 0 4 8 12 16 20 24 28 32 Frequency [MHz] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 159 Figure 38-85.Active mode supply current vs. VCC. fSYS = 32.768kHz internal oscillator. 175 -40C 160 25C 85C 105C 145 I CC [A] 130 115 100 85 70 55 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-86.Active mode supply current vs. VCC. fSYS = 1MHz external clock. 900 -40C 25C 85C 105C 830 760 I CC [A] 690 620 550 480 410 340 270 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 160 Figure 38-87.Active mode supply current vs. VCC. fSYS = 2MHz internal oscillator. 1800 -40 C 25 C 85 C 105 C 1650 1500 I CC [A] 1350 1200 1050 900 750 600 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-88.Active mode supply current vs. VCC. fSYS = 32MHz internal oscillator prescaled to 8MHz. 7.5 -40 C 25 C 85 C 105 C 6.9 6.3 I CC [mA] 5.7 5.1 4.5 3.9 3.3 2.7 2.1 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 161 Figure 38-89.Active mode supply current vs. VCC. fSYS = 32MHz internal oscillator. 21 -40 C 20 25C 85C 105C 19 I CC [mA] 18 17 16 15 14 13 2.7 2.8 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6 VCC [V] 38.2.1.2 Idle mode supply current Figure 38-90.Idle mode supply current vs. frequency. fSYS = 0 - 1MHz external clock, T = 25C. ICC [A] 250 225 3.3 V 200 3.0 V 175 2.7 V 150 2.2 V 125 1.8 V 100 75 50 25 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Frequency [MHz] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 162 Figure 38-91.Idle mode supply current vs. frequency. fSYS = 1 - 32MHz external clock, T = 25C. 8 3.3 V 7 3.0 V ICC [mA] 6 2.7 V 5 4 2.2 V 3 2 1.8 V 1 0 0 4 8 12 16 20 24 28 32 Frequency [MHz] Figure 38-92.Idle mode supply current vs. VCC. fSYS = 32.768kHz internal oscillator. 41.5 40.0 105C 38.5 I CC [A] 37.0 85 C -40C 35.5 25C 34.0 32.5 31.0 29.5 28.0 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 163 Figure 38-93.Idle mode supply current vs. VCC. fSYS = 1MHz external clock. 270 105 C 85 C 25C -40C 250 230 I CC [A] 210 190 170 150 130 110 90 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-94.Idle mode supply current vs. VCC. fSYS = 2MHz internal oscillator. 600 -40C 25C 85C 105C 550 I CC [A] 500 450 400 350 300 250 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 164 Figure 38-95.Idle mode supply current vs. VCC. fSYS = 32MHz internal oscillator prescaled to 8MHz. 3100 -40C 25C 85C 105C 2800 I CC [A] 2500 2200 1900 1600 1300 1000 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-96.Idle mode current vs. VCC. fSYS = 32MHz internal oscillator. 8650 -40C 25C 85C 105C 8300 7950 I CC [A] 7600 7250 6900 6550 6200 5850 5500 2.7 2.8 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 165 38.2.1.3 Power-down mode supply current Figure 38-97.Power-down mode supply current vs. Temperature. All functions disabled. 6.00 3.3 V 3.0 V 2.7 V 2.2 V 1.8 V 5.25 4.50 I CC [A] 3.75 3.00 2.25 1.50 0.75 0.00 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] Figure 38-98.Power-down mode supply current vs. Temperature. Sampled BOD with Watchdog Timer running on ULP oscillator. 6.05 3.3 V 3.0 V 2.7 V 2.2 V 1.8 V 5.30 I CC [A] 4.55 3.80 3.05 2.30 1.55 0.80 -45 -30 -15 0 15 30 45 60 75 90 105 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 166 38.2.1.4 Power-save mode supply current Figure 38-99.Power-save mode supply current vs. VCC. Real Time Counter enabled and running from 1.024kHz output of 32.768kHz TOSC. 0.90 0.85 Normal mode ICC [A] 0.80 0.75 0.70 0.65 Low-power mode 0.60 0.55 0.50 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] 38.2.1.5 Standby mode supply current Figure 38-100. Standby supply current vs. VCC. Standby, fSYS = 1MHz. 9.5 85C 9.0 8.5 25C -40C 8.0 7.5 ICC [A] 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 167 Figure 38-101. Standby supply current vs. VCC. 25C, running from different crystal oscillators. 500 16MHz 12MHz 450 ICC [A] 400 350 8MHz 2MHz 300 250 0.454MHz 200 150 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VCC [V] 38.2.2 I/O Pin Characteristics 38.2.2.1 Pull-up Figure 38-102. I/O pin pull-up resistor current vs. pin voltage. VCC = 1.8V. 80 70 I pin [A] 60 50 40 30 -40C 25C 85C 105C 20 10 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 VPIN [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 168 Figure 38-103. I/O pin pull-up resistor current vs. pin voltage. VCC = 3.0V. 120 105 90 I pin [A] 75 60 45 30 -40C 25 C 85 C 105C 15 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VPIN [V] Figure 38-104. I/O pin pull-up resistor current vs. pin voltage. VCC = 3.3V. 140 120 I pin [A] 100 80 60 40 -40C 25 C 85 C 105C 20 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 VPIN [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 169 38.2.2.2 Output Voltage vs. Sink/Source Current Figure 38-105.I/O pin output voltage vs. source current. VCC = 1.8V. 1.85 1.70 1.55 V PIN [V] 1.40 1.25 1.10 0.95 -40C 0.80 25C 85C 105C 0.65 0.50 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 -12 -9 -6 -3 0 IPIN [mA] Figure 38-106.I/O pin output voltage vs. source current. VCC = 3.0V. 3.2 2.9 2.6 V PIN [V] 2.3 2.0 1.7 1.4 -40C 1.1 105C 25C 0.8 85C 0.5 -30 -27 -24 -21 -18 -15 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 170 Figure 38-107.I/O pin output voltage vs. source current. VCC = 3.3V. 3.5 3.2 2.9 2.6 VPIN [V] 2.3 2.0 -40C 1.7 25C 1.4 1.1 85C 0.8 105C 0.5 -30 -27 -24 -21 -18 -15 -12 -9 -6 -3 0 IPIN [mA] Figure 38-108.I/O pin output voltage vs. source current. 3.8 3.6V 3.4 3.3V VPIN [V] 3.0 2.7V 2.6 2.2 1.8V 1.8 1.4 1.0 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 171 Figure 38-109.I/O pin output voltage vs. sink current. VCC = 1.8V. 1.6 105C 1.4 1.2 85C VPIN [V] 1.0 0.8 25C -40C 0.6 0.4 0.2 0.0 0 2 4 6 8 10 12 14 16 IPIN [mA] Figure 38-110.I/O pin output voltage vs. sink current. VCC = 3.0V. 1.20 1.05 105C 85C 0.90 25C -40C V PIN [V] 0.75 0.60 0.45 0.30 0.15 0.00 0 3 6 9 12 15 18 21 24 27 30 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 172 Figure 38-111.I/O pin output voltage vs. sink current. VCC = 3.3V. 1.08 105C 85C 25C -40C 0.96 0.84 V PIN [V] 0.72 0.60 0.48 0.36 0.24 0.12 0.00 0 4 8 12 16 20 24 28 32 IPIN [mA] Figure 38-112.I/O pin output voltage vs. sink current. 1.50 1.8V 1.35 1.20 VPIN [V] 1.05 0.90 2.7V 3.3V 3.6V 0.75 0.60 0.45 0.30 0.15 0.00 5 7 9 11 13 15 17 19 21 23 25 IPIN [mA] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 173 38.2.2.3 Thresholds and Hysteresis Figure 38-113.I/O pin input threshold voltage vs. VCC. T = 25C. 1.85 VIH 1.70 VIL Vthreshold [V] 1.55 1.40 1.25 1.10 0.95 0.80 0.65 0.50 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-114.I/O pin input threshold voltage vs. VCC. VIH I/O pin read as "1". 1.88 -40C 25C 85C 105C 1.76 Vthreshold[V] 1.64 1.52 1.4 1.28 1.16 1.04 0.92 0.8 1.6 1.85 2.1 2.35 2.6 2.85 3.1 3.35 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 174 Figure 38-115.I/O pin input threshold voltage vs. VCC. VIL I/O pin read as "0". 1.70 105C 85 C 25 C -40C 1.55 V threshold [V] 1.40 1.25 1.10 0.95 0.80 0.65 0.50 1.6 1.85 2.1 2.35 2.6 2.85 3.1 3.35 3.6 VCC [V] Figure 38-116.I/O pin input hysteresis vs. VCC. 0.36 -40 C 0.33 Vthreshold [V] 0.3 0.27 25C 0.24 0.21 85C 0.18 0.15 105C 0.12 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 175 38.2.3 ADC Characteristics Figure 38-117.INL error vs. external VREF. T = 25C, VCC = 3.6V, external reference. 1.6 1.5 Single-ended unsigned mode INL [LSB] 1.4 1.3 Differential mode 1.2 1.1 1 Single-ended signed mode 0.9 0.8 0.7 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 1850 2000 VREF [V] Figure 38-118.INL error vs. sample rate. T = 25C, VCC = 3.6V, VREF = 2.0V external. 1.17 1.14 Differential mode 1.11 Single-ended Unsigned mode INL [LSB] 1.08 1.05 1.02 Single-ended Signed mode 0.99 0.96 0.93 0.9 500 650 800 950 1100 1250 1400 1550 1700 ADC Sample rate [ksps] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 176 Figure 38-119.INL error vs. input code 2 1.5 INL [LSB] 1 0.5 0 -0.5 -1 -1.5 -2 0 512 1024 1536 2048 2560 3072 3584 4096 ADC input code Figure 38-120.DNL error vs. external VREF. T = 25C, VCC = 3.6V, external reference. 1.3 1.2 Single-ended unsigned mode 1.1 DNL [LSB] 1 0.9 0.8 0.7 0.6 Differential mode 0.5 0.4 Single-ended signed mode 0.3 0.2 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 177 Figure 38-121.DNL error vs. sample rate. T = 25C, VCC = 3.6V, VREF = 2.0V external. 0.53 0.51 Differential mode DNL [LSB] 0.49 0.47 Single-ended signed mode 0.45 0.43 0.41 0.39 Single-ended unsigned mode 0.37 0.35 500 650 800 950 1100 1250 1400 1550 1700 1850 2000 ADC sample rate [ksps] Figure 38-122.DNL error vs. input code. 0.7 0.6 DNL [LSB] 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 0 512 1024 1536 2048 2560 3072 3584 4096 ADC input code XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 178 Figure 38-123.Gain error vs. VREF. T = 25C, VCC = 3.6V, ADC sampling speed = 500ksps. 10 9 Single-ended signed mode Gain Error [mV] 8 7 6 5 Single-ended unsigned mode 4 3 2 Differential mode 1 0 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] Figure 38-124.Gain error vs. VCC. T = 25C, VREF = external 1.0V, ADC sampling speed = 500ksps. 9 8 Single-ended signed mode Gain error [mV] 7 6 5 4 Single-ended unsigned mode 3 2 Differential mode 1 0 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 179 Figure 38-125.ADC Offset error vs. VREF. T = 25C, VCC = 3.6V, ADC sampling speed = 500ksps. -0.8 -0.85 Offset [mV] -0.9 -0.95 -1 -1.05 Differential mode -1.1 -1.15 -1.2 -1.25 -1.3 -1.35 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] Figure 38-126.Gain error vs. temperature. VCC = 3.0V, VREF = external 2.0V. 11 10 Single-ended Signed Gain Error [mV] 9 8 7 6 5 Single-ended Unsigned 4 3 Differential 2 1 0 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 180 Figure 38-127.ADC Offset vs. VCC. T = 25C, VREF = external 1.0V, ADC sampling speed = 500ksps. -0.2 -0.25 Offset [mV] -0.3 -0.35 Differential mode -0.4 -0.45 -0.5 -0.55 -0.6 -0.65 -0.7 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-128.Noise vs. VREF. T = 25C, VCC = 3.6V, ADC sampling speed = 500ksps. 0.47 0.46 Differential Noise [mV RMS] 0.45 0.44 0.43 0.42 0.41 0.4 0.39 0.38 0.37 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 181 Figure 38-129.Noise vs. VCC. T = 25C, VREF = external 1.0V, ADC sampling speed = 500ksps. 0.42 Noise [mV RMS] 0.41 Differential 0.4 0.39 0.38 0.37 0.36 0.35 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] 38.2.4 DAC Characteristics Figure 38-130.DAC INL error vs. VREF. VCC = 3.6V, external reference, room temperature. 1.9 1.8 INL [LSB] 1.7 1.6 1.5 1.4 1.3 1.2 1.1 25C 1 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 182 Figure 38-131.DAC DNL error vs. VREF. VCC = 3.6V, external reference, room temperature. 1.35 1.25 DNL [LSB] 1.15 1.05 0.95 0.85 0.75 0.65 25C 0.55 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 VREF [V] Figure 38-132.DAC noise vs. temperature. VCC = 3.0V, VREF = 2.4V . 0.183 0.181 Noise [mV RMS] 0.179 0.177 0.175 0.173 0.171 0.169 0.167 0.165 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 75 85 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 183 38.2.5 Analog Comparator Characteristics Figure 38-133.Analog comparator hysteresis vs. VCC. High-speed, small hysteresis. 53 105 C 85 C 25 C -40C 51 49 V HYST [mV] 47 45 43 41 39 37 35 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-134.Analog comparator hysteresis vs. VCC. Low power, small hysteresis. 37.0 35.5 105C 85 C 34.0 VHYST [mV] 32.5 31.0 25 C 29.5 -40C 28.0 26.5 25.0 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 184 Figure 38-135.Analog comparator hysteresis vs. VCC. High-speed mode, large hysteresis. 53 105 C 85 C 25 C -40C 51 49 V HYST [mV] 47 45 43 41 39 37 35 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-136.Analog comparator hysteresis vs. VCC. Low power, large hysteresis. 77 105C 85C 74 71 VHYST [mV] 68 65 25C 62 59 -40C 56 53 50 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 185 Figure 38-137.Analog comparator current source vs. calibration value. Temperature = 25C. 8 7 I [A] 6 5 3.3V 3.0V 2.7V 4 3 2.2V 1.8V 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CALIB[3..0] Figure 38-138.Analog comparator current source vs. calibration value. VCC = 3.0V. 6.0 5.7 I CURRENTSOURCE [A] 5.4 5.1 4.8 4.5 4.2 3.9 -40 C 25 C 85 C 105 C 3.6 3.3 3.0 0 2 4 6 8 10 12 14 16 CALIB[3..0] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 186 Figure 38-139.Voltage scaler INL vs. SCALEFAC. T = 25C, VCC = 3.0V. 0.30 0.25 INL [LSB] 0.20 0.15 0.10 0.05 25C 0.00 -0.05 -0.10 0 7 14 21 28 35 42 49 56 63 SCALEFAC 38.2.6 Internal 1.0V reference Characteristics Figure 38-140. ADC/DAC Internal 1.0V reference vs. temperature. 3.6 V 3.3 V 3.0 V 2.7 V 1.8 V 1.6 V 1.005 1.002 0.999 Bandgap Voltage [V] 0.996 0.993 0.990 0.987 0.984 0.981 0.978 0.975 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 187 38.2.7 BOD Characteristics Figure 38-141.BOD thresholds vs. temperature. BOD level = 1.6V. 1.650 Rising Vcc 1.645 1.640 Falling Vcc 1.635 V BOT [V] 1.630 1.625 1.620 1.615 1.610 1.605 1.600 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] Figure 38-142.BOD thresholds vs. temperature. BOD level = 3.0V. 3.090 Rising Vcc 3.075 3.060 V BOT [V] 3.045 Falling Vcc 3.030 3.015 3.000 2.985 2.970 2.955 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 188 38.2.8 External Reset Characteristics Figure 38-143.Minimum Reset pin pulse width vs. VCC. 120 110 tRST [ns] 100 90 25C -40C 80 70 85C 60 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-144.Reset pin pull-up resistor current vs. reset pin voltage. VCC = 1.8V. 80 -40C 70 25C IRESET[uA] 60 85C 50 40 30 20 10 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 VRESET [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 189 Figure 38-145.Reset pin pull-up resistor current vs. reset pin voltage. VCC = 3.0V. 135 -40C 120 25C IRESET [A] 105 85C 90 75 60 45 30 15 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 2.80 3.15 3.50 VRESET [V] Figure 38-146.Reset pin pull-up resistor current vs. reset pin voltage. VCC = 3.3V. IRESET [A] 160 140 -40C 25C 120 85C 100 80 60 40 20 0 0.00 0.35 0.70 1.05 1.40 1.75 2.10 2.45 VRESET [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 190 Figure 38-147.Reset pin input threshold voltage vs. VCC. VIH - Reset pin read as "1". 2.20 -40C 25C 85C 2.05 Vthreshold [V] 1.90 1.75 1.60 1.45 1.30 1.15 1.00 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] Figure 38-148.Reset pin input threshold voltage vs. VCC. VIL - Reset pin read as "0". 1.85 -40C 25C 85C 1.70 1.55 Vthreshold [V] 1.40 1.25 1.10 0.95 0.80 0.65 0.50 0.35 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 191 38.2.9 Power-on Reset Characteristics Figure 38-149.Power-on reset current consumption vs. VCC. BOD level = 3.0V, enabled in continuous mode. 1500 1350 -40C 1200 25C 85C ICC [A] 1050 900 750 600 450 300 150 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VCC [V] Figure 38-150.Power-on reset current consumption vs. VCC. BOD level = 3.0V, enabled in sampled mode. 1350 -40C 1200 25C 1050 85C ICC [A] 900 750 600 450 300 150 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 192 38.2.10 Oscillator Characteristics 38.2.10.1 Ultra Low-Power internal oscillator Figure 38-151.Ultra Low-Power internal oscillator frequency vs. temperature. 30.0 29.6 Frequency [kHz] 29.2 28.8 28.4 28.0 3.3 V 3.0 V 2.7 V 2.2 V 1.8 V 27.6 27.2 26.8 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] 38.2.10.2 32.768kHz Internal Oscillator Figure 38-152. 32.768kHz internal oscillator frequency vs. temperature. 32.900 1.8 V 2.2 V 2.7 V 3.3 V 3.0 V 32.850 Frequency [kHz] 32.800 32.750 32.700 32.650 32.600 32.550 32.500 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 193 Figure 38-153. 32.768kHz internal oscillator frequency vs. calibration value. VCC = 3.0V, T = 25C. 50 47 Frequency [kHz] 44 41 38 35 32 29 26 23 20 0 30 60 90 120 150 180 210 240 270 RC32KCAL[7..0] 38.2.10.3 2MHz Internal Oscillator Figure 38-154. 2MHz internal oscillator frequency vs. temperature. DFLL disabled. 2.07 2.06 Frequency [MHz] 2.05 2.04 2.03 2.02 2.01 3.3 V 3.0 V 2.7 V 2.2 V 1.8 V 2.00 1.99 1.98 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 194 Figure 38-155. 2MHz internal oscillator frequency vs. temperature. DFLL enabled. 2.0100 1.8 V 2.2 V 2.7 V 2.0075 Frequency [MHz] 2.0050 3.3 V 3.0 V 2.0025 2.0000 1.9975 1.9950 1.9925 1.9900 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] Figure 38-156. 2MHz internal oscillator CALA calibration step size. VCC = 3V. 0.24 Frequency step size [%] 0.23 0.21 0.20 0.18 0.17 105 C -40 C 85 C 25 C 0.15 0.14 0.12 0 15 30 45 60 75 90 105 120 135 CALA XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 195 38.2.10.4 32MHz Internal Oscillator Figure 38-157. 32MHz internal oscillator frequency vs. temperature. DFLL disabled. 34.2 33.9 Frequency [MHz] 33.6 33.3 33.0 32.7 32.4 32.1 3.3 V 3.0 V 2.7 V 2.2 V 1.8 V 31.8 31.5 31.2 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] Figure 38-158. 32MHz internal oscillator frequency vs. temperature. DFLL enabled, from the 32.768kHz internal oscillator. 32.10 32.05 3.3 V Frequency [MHz] 32.00 1.8 V 2.2 V 31.95 3.0 V 31.90 2.7 V 31.85 31.80 31.75 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 196 Figure 38-159. 32MHz internal oscillator CALA calibration step size. VCC = 3.0V. 0.30 Frequency Step size [%] 0.28 0.26 0.24 0.22 0.20 85C 0.18 105C 25C -40C 0.16 0.14 0.12 0.10 0 15 30 45 60 75 90 105 120 135 CALA Figure 38-160. 32MHz internal oscillator frequency vs. CALB calibration value. VCC = 3.0V, DFLL disabled. 75 -40C 25 C 85 C 105C 70 Frequency [MHz] 65 60 55 50 45 40 35 30 25 0 8 16 24 32 40 48 56 64 CALB XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 197 38.2.10.5 32MHz internal oscillator calibrated to 48MHz Figure 38-161. 48MHz internal oscillator frequency vs. temperature. DFLL disabled. 51.50 51.00 Frequency [MHz] 50.50 50.00 49.50 49.00 48.50 3.3 V 3.0 V 2.7 V 2.2 V 1.8 V 48.00 47.50 47.00 46.50 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] Figure 38-162. 48MHz internal oscillator frequency vs. temperature. DFLL enabled, from the 32.768kHz internal oscillator. 48.16 1.8 V 2.2 V 2.7 V 3.0 V 3.3 V 48.08 Frequency [MHz] 48.00 47.92 47.84 47.76 47.68 47.60 -40 -25 -10 5 20 35 50 65 80 95 110 Temperature [C] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 198 Figure 38-163. 32MHz internal oscillator CALA calibration step size. Using 48MHz calibration value from signature row, VCC = 3.0V. 0.30 Frequency Step size [%] 0.28 0.26 0.24 0.22 0.20 105C 85C 25C -40C 0.18 0.16 0.14 0.12 0.10 0 15 30 45 60 75 90 105 120 135 CALA 38.2.11 PDI characteristics Figure 38-164.Maximum PDI frequency vs. VCC. 34 -40 C 25 C 85 C 105 C 31 28 f MAX [MHz] 25 22 19 16 13 10 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 VCC [V] XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 199 39. Errata 39.1 ATxmega64A1U 39.1.1 Rev. L Register ANAINIT in MCUR will always read as zero Enabling DFLL with illegal reference oscillator will lock the DFLL XOSCPWR configuration is non-functional Configuration of PGM and CWCM is not as described in XMEGA AU Manual AWEX PWM output after fault restarted with wrong values RTC Counter value not correctly read after sleep RTC clock output option is non-functional USB, when receiving 1023 byte length isochronous frame, it will corrupt 1024th SRAM location USB endpoint table is 16-byte alignment USB Auto ZLP feature is non-functional Disabling the USART transmitter does not automatically set the TxD pin direction to input TWI, SDAHOLD configuration in the TWI CTRL register is one bit ADC has increased INL error in when used in SE unsigned mode at low temperatures ADC is non-functional in SE unsigned mode with VREF below 1.8V ADC has increased linearity error when using the gain stage above 500ksps DAC Offset calibration range too small when using AVCC as reference DAC clock noise Internal 1V reference has noise at low temperature 1 Register ANAINIT in MCUR will always read as zero The ANAINIT register in the MCUR module will always be read as zero even if written to a value. The actual content of the register is correct. Problem fix/Workaround Do not use software that reads these registers to get the Analog Initialization configuration. 2. Enabling DFLL with illegal reference oscillator will lock the clock system If external crystal is selected as reference for DFLL, but no crystal is connected and DFLL is enabled, the DFLL will be locked until reset is issued. Problem fix/Workaround Do not enable DFLL before reference clock is present, enabled and ready. 3. XOSCPWR configuration is non-functional The Crystal oscillator drive (XOSCPWR) option in the XOSC Control register is non-functional. Problem fix/Workaround None. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 200 4. Configuration of PGM and CWCM is not as described in XMEGA AU Manual Configuration of common waveform channel mode (CWCM) and pattern generation mode (PGM), is not as described in the XMEGA AU manual. Problem fix/Workaround Configure PWM and CWCM according to the Table 39-1 on page 201. Table 39-1. PWM and CWCM configuration. PGM CWCM Description 0 0 PGM and CWCM disabled 0 1 PGM enabled 1 0 PGM and CWCM enabled 1 1 PGM enabled 5. AWEX PWM output after fault restarted with wrong values When recovering from fault state, the PWM output will drive wrong values to the port for up to two CLKPER + one CLKPER4 cycles. Problem fix/Workaround The following seqence can be used in Latched Mode: a. b. c. d. e. Disable DTI outputs (Write DTICCxEN to 0) Clear fault flag Wait for Overflow Re-enable DTI (Write DTICCxEN to 1) Set pin direction to Output This will remove the glitch, but the following period will be shorter. In Cycle-by-cycle mode the same procedure can be followed as long as the Pattern Generation Mode is not enabled. For Pattern generation mode, there is no workaround. 6. RTC Counter value not correctly read after sleep If a real time counter (RTC) interrupt is used wake up the device from sleep, and bit 0 of RTC count register (CNT) has the same value as when the device entered sleep, CNT will not be read correctly during the first prescaled RTC clock cycle after wakeup. The value read will be the same as the value in the register was when entering sleep. Problem fix/Workaround Wait at least one prescaled RTC clock cycle before reading CNT. 7. RTC clock output option is non-functional The real time counter (RTC) as clock output option is non-functional, and setting the RTCOUT bit in the clock and event out register (CLKEVOUT ) will have no effect. Problem fix/Workaround None XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 201 8. USB, when receiving 1023Byte length isochronous frame, it will corrupt 1024th SRAM location When USB is configured for isochronous operation and 1023Byte data payload size, the 1024th RAM location that is directly after the endpoint RAM buffer will be corrupted. Problem fix/Workaround Allocate 1024bytes RAM buffer when using 1023 isochronous endpoint. This workaround is implemented in all USB software and source code delivered from Atmel in the AVR Software Framework. 9. USB endpoint table is 16-byte alignment The USB endpoint table uses 16-byte alignment, instead of 16-bit alignment. Problem fix/Workaround Align the endpoint configuration table pointer in SRAM to a 16-byte. This workaround is implemented in all USB software and source code delivered from Atmel in the AVR Software Framework. 10. USB Auto ZLP feature is non-functional The Auto ZLP feature is non-functional and can not be used. Problem fix/Workaround None. 11. Disabling the USART transmitter does not automatically set the TxD pin direction to input If the USART transmitter is idle with no frames to transmit, setting TXEN to zero will not automatically set the TxD pin direction to input. Problem fix/Workaround The TxD pin direction can be set to input using the Port pin direction to input using the port direction (DIR) register. When the port pin direction is input, it will be immediate and ongoing transmissions will be truncated. 12. TWI, SDAHOLD configuration in the TWI CTRL register is one bit The SDAHOLD configuration in the TWI Control register (CTRL) is one bit. Due to this the SDA hold time can be configured for maximum ~50ns when enabled. Configuring for longer hold time will have no effect. Problem fix/Workaround If longer SDA hold time than 50nS is required it must be handled in software. 13. ADC has increased INL error in when used in SE unsigned mode at low temperatures When the ADC is used on single ended (SE) unsigned mode, -INL error is increased up to +/- 5 LSB in temperatures below -20C. Problem fix/Workaround Use the ADC in single ended signed mode. 14. ADC is non-functional in SE unsigned mode with VREF below 1.8V When the ADC is used on single ended unsigned mode and VREF is below 1.8V, INL and DNL error is increased above +/- 10LSB, i.e. the ADC have missing codes under this condition. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 202 Problem fix/Workaround Use the ADC in single ended signed mode. 15. ADC has increased linearity error when using the gain stage above 500ksps The INL error for gain stage is increased to above 20LSB for sampling speed exceeding 500 ksps. Problem fix/Workaround None. 16. DAC Offset calibration range too small when using AVCC as reference If using AVCC as reference, the DAC offset calibration will not totally remove the offset error. Offset could be up to 100LSB after calibration. Problem fix/Workaround Offset adjustment must be partly handled in software. 17. DAC clock noise The system clock is visible as clock noise on the output of the DAC. Peak to peak noise is in the range 0.7mV - 1.6mV at 2MHz and 0.05mV to 0.1mV at 32MHz. If external clock is used as system clock, the noise is up to three times higher. Problem fix/Workaround Add external low-pass filter to remove the noise. 18. Internal 1V reference has noise at low temperature The internal 1.0V reference for the ADC and DAC has increased noise at low temperatures. The noise can result in INL numbers up to +/- 20 LSB at temperatures below 0C. Problem fix/Workaround For the ADC, use oversampling to reduce noise. For the DAC use external filter to reduce the noise. 39.1.2 Rev. A - K Not sampled. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 203 39.2 ATxmega128A1U 39.2.1 Rev. L Register ANAINIT in MCUR will always read as zero Enabling DFLL with illegal reference oscillator will lock the DFLL XOSCPWR configuration is non-functional Configuration of PGM and CWCM is not as described in XMEGA AU Manual AWEX PWM output after fault restarted with wrong values RTC Counter value not correctly read after sleep RTC clock output option is non-functional USB, when receiving 1023 byte length isochronous frame, it will corrupt 1024th SRAM location USB endpoint table is 16-byte alignment USB Auto ZLP feature is non-functional Disabling the USART transmitter does not automatically set the TxD pin direction to input TWI, SDAHOLD configuration in the TWI CTRL register is one bit ADC has increased INL error in when used in SE unsigned mode at low temperatures ADC is non-functional in SE unsigned mode with VREF below 1.8V ADC has increased linearity error when using the gain stage above 500ksps DAC Offset calibration range too small when using AVCC as reference DAC clock noise Internal 1V reference has noise at low temperature 1 Register ANAINIT in MCUR will always read as zero The ANAINIT register in the MCUR module will always be read as zero even if written to a value. The actual content of the register is correct. Problem fix/Workaround Do not use software that reads these registers to get the Analog Initialization configuration. 2. Enabling DFLL with illegal reference oscillator will lock the clock system If external crystal is selected as reference for DFLL, but no crystal is connected and DFLL is enabled, the DFLL will be locked until reset is issued. Problem fix/Workaround Do not enable DFLL before reference clock is present, enabled and ready. 3. XOSCPWR configuration is non-functional The Crystal oscillator drive (XOSCPWR) option in the XOSC Control register is non-functional. Problem fix/Workaround None. 4. Configuration of PGM and CWCM is not as described in XMEGA AU Manual Configuration of common waveform channel mode (CWCM) and pattern generation mode (PGM), is not as described in the XMEGA AU manual. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 204 Problem fix/Workaround Configure PWM and CWCM according to the Table 39-1 on page 201. Table 39-2. PWM and CWCM configuration. PGM CWCM Description 0 0 PGM and CWCM disabled 0 1 PGM enabled 1 0 PGM and CWCM enabled 1 1 PGM enabled 5. AWEX PWM output after fault restarted with wrong values When recovering from fault state, the PWM output will drive wrong values to the port for up to two CLKPER + one CLKPER4 cycles. Problem fix/Workaround The following seqence can be used in Latched Mode: a. b. c. d. e. Disable DTI outputs (Write DTICCxEN to 0) Clear fault flag Wait for Overflow Re-enable DTI (Write DTICCxEN to 1) Set pin direction to Output This will remove the glitch, but the following period will be shorter. In Cycle-by-cycle mode the same procedure can be followed as long as the Pattern Generation Mode is not enabled. For Pattern generation mode, there is no workaround. 6. RTC Counter value not correctly read after sleep If a real time counter (RTC) interrupt is used wake up the device from sleep, and bit 0 of RTC count register (CNT) has the same value as when the device entered sleep, CNT will not be read correctly during the first prescaled RTC clock cycle after wakeup. The value read will be the same as the value in the register was when entering sleep. Problem fix/Workaround Wait at least one prescaled RTC clock cycle before reading CNT. 7. RTC clock output option is non-functional The real time counter (RTC) as clock output option is non-functional, and setting the RTCOUT bit in the clock and event out register (CLKEVOUT) will have no effect. Problem fix/Workaround None 8. USB, when receiving 1023Byte length isochronous frame, it will corrupt 1024th SRAM location When USB is configured for isochronous operation and 1023Byte data payload size, the 1024th RAM location that is directly after the endpoint RAM buffer will be corrupted. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 205 Problem fix/Workaround Allocate 1024bytes RAM buffer when using 1023 isochronous endpoint. This workaround is implemented in all USB software and source code delivered from Atmel in the AVR Software Framework. 9. USB endpoint table is 16-byte alignment The USB endpoint table uses 16-byte alignment, instead of 16-bit alignment. Problem fix/Workaround Align the endpoint configuration table pointer in SRAM to a 16-byte. This workaround is implemented in all USB software and source code delivered from Atmel in the AVR Software Framework. 10. USB Auto ZLP feature is non-functional The Auto ZLP feature is non-functional and can not be used. Problem fix/Workaround None. 11. Disabling the USART transmitter does not automatically set the TxD pin direction to input If the USART transmitter is idle with no frames to transmit, setting TXEN to zero will not automatically set the TxD pin direction to input. Problem fix/Workaround The TxD pin direction can be set to input using the Port pin direction to input using the port direction (DIR) register. When the port pin direction is input, it will be immediate and ongoing transmissions will be truncated. 12. TWI, SDAHOLD configuration in the TWI CTRL register is one bit The SDAHOLD configuration in the TWI Control register (CTRL) is one bit. Due to this the SDA hold time can be configured for maximum ~50ns when enabled. Configuring for longer hold time will have no effect. Problem fix/Workaround If longer SDA hold time than 50nS is required it must be handled in software. 13. ADC has increased INL error in when used in SE unsigned mode at low temperatures When the ADC is used on single ended (SE) unsigned mode, -INL error is increased up to +/- 5 LSB in temperatures below -20C. Problem fix/Workaround Use the ADC in single ended signed mode. 14. ADC is non-functional in SE unsigned mode with VREF below 1.8V When the ADC is used on single ended unsigned mode and VREF is below 1.8V, INL and DNL error is increased above +/- 10LSB, i.e. the ADC have missing codes under this condition. Problem fix/Workaround Use the ADC in single ended signed mode. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 206 15. ADC has increased linearity error when using the gain stage above 500ksps The INL error for gain stage is increased to above 20LSB for sampling speed exceeding 500 ksps. Problem fix/Workaround None. 16. DAC Offset calibration range too small when using AVCC as reference If using AVCC as reference, the DAC offset calibration will not totally remove the offset error. Offset could be up to 100LSB after calibration. Problem fix/Workaround Offset adjustment must be partly handled in software. 17. DAC clock noise The system clock is visible as clock noise on the output of the DAC. Peak to peak noise is in the range 0.7mV - 1.6mV at 2MHz and 0.05mV to 0.1mV at 32MHz. If external clock is used as system clock, the noise is up to three times higher. Problem fix/Workaround Add external low-pass filter to remove the noise. 18. Internal 1V reference has noise at low temperature The internal 1.0V reference for the ADC and DAC has increased noise at low temperatures. The noise can result in INL numbers up to +/- 20 LSB at temperatures below 0C. Problem fix/Workaround For the ADC, use oversampling to reduce noise. For the DAC use external filter to reduce the noise. 39.2.2 Rev. A - K Not sampled. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 207 40. Datasheet Revision History Please note that the referring page numbers in this section are referred to this document. The referring revision in this section are referring to the document revision. 40.1 8385G - 11/2013 1. 40.2 8385F - 12/2012 1. 40.3 40.4 Updated the typical characteristics at 105C for "ATxmega128A1U" on page 204. 8385E - 11/2012 1. Updated the whole contents with an updated template (table tags and paragraph tags). 2. Updated the 100C1 package type on page 2. Ball pitch is 0.80mm instead of 0.88mm. 3. Updated Figure 2-1 on page 3. Pin 14 is VCC and not VDD. 4. Updated Table 7-2 on page 14. ATxmega64A1U has internal SRAM (4K). ATxmega128A1U has internal SRAM (8K). 5. Updated Figure 15-7 on page 33, "Input sensing system overview" . 6. Updated Figure 31-1 on page 54, "Analog comparator overview." 7. Added electrical characterization for "ATxmega64A1U" on page 74. 8. Updated Table 37-28 on page 89 and Table 37-61 on page 111. Added ESR and start-up time parameters. 9. Added typical characteristics for "ATxmega64A1U" on page 118. 8385D - 07/2012 1. 40.5 Updated note 2 in Port H - Alternate Functions in Table 33-7 on page 60. Updated Table 7-2 on page 15. Devices are respectively ATxmega64A1U and ATxmega128A1U. 8385C - 07/2012 1. Updated Table 7-1 on page 13. Device ID for ATxmega128A1U is 4C97. Device ID for ATxmega64A1U is 4E96. 2. Updated the package "100C2" on page 73. The ball rows are A-K (without I). 3. Updated the whole datasheet using the Atmel new updated datasheet template that includes Atmel new logo and new registered TM. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 208 40.6 40.7 8385B - 03/2012 1. Added "Electrical Characteristics" on page 74. 2. Added "Typical Characteristics" on page 118. 3. Updated "Errata" on page 200. 4. Used Atmel new datasheet template that includes Atmel new addresses on the last page. 8385A - 11/2011 1. Initial revision. XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 209 Table of Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Pinout/Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.1 Recommended reading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5. Capacitive touch sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6. AVR CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Architectural Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ALU - Arithmetic Logic Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Program Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Stack and Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Register File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7. Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flash Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuses and Lock bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Memory and Bus Arbitration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Memory Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Device ID and Revision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Memory Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . JTAG Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flash and EEPROM Page Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 12 13 13 14 14 14 14 15 15 15 15 15 8. DMAC - Direct Memory Access Controller . . . . . . . . . . . . . . . . . . . 17 8.1 8.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 9. Event System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9.1 9.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 10. System Clock and Clock options . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10.1 10.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 i 10.3 Clock Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 11. Power Management and Sleep Modes . . . . . . . . . . . . . . . . . . . . . . 22 11.1 11.2 11.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Sleep Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 12. System Control and Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 12.1 12.2 12.3 12.4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 24 24 24 13. WDT - Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 13.1 13.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 14. Interrupts and Programmable Multilevel Interrupt Controller . . . . . . 27 14.1 14.2 14.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Interrupt vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 15. I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 15.1 15.2 15.3 15.4 15.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alternate Port Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 30 31 33 33 16. TC0/1 - 16-bit Timer/Counter Type 0 and 1 . . . . . . . . . . . . . . . . . . 34 16.1 16.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 17. TC2 - Time/Counter Type 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 17.1 17.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 18. AWeX - Advanced Waveform Extension . . . . . . . . . . . . . . . . . . . . . 37 18.1 18.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 19. Hi-Res - High Resolution Extension . . . . . . . . . . . . . . . . . . . . . . . . 38 19.1 19.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 20. RTC - 16-bit Real-Time Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 20.1 20.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 21. USB - Universal Serial Bus Interface . . . . . . . . . . . . . . . . . . . . . . . 40 21.1 21.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 22. TWI - Two-Wire Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 ii 22.1 22.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 23. SPI - Serial Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 23.1 23.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 24. USART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 24.1 24.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 25. IRCOM - IR Communication Module . . . . . . . . . . . . . . . . . . . . . . . . 45 25.1 25.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 26. AES and DES Crypto Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 26.1 26.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 27. CRC - Cyclic Redundancy Check Generator . . . . . . . . . . . . . . . . . 47 27.1 27.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 28. EBI - External Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 28.1 28.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 29. ADC - 12-bit Analog to Digital Converter . . . . . . . . . . . . . . . . . . . . 49 29.1 29.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 30. DAC - 12-bit Digital to Analog Converter . . . . . . . . . . . . . . . . . . . . 51 30.1 30.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 31. AC - Analog Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 31.1 31.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 32. PDI - Programming and Debugging . . . . . . . . . . . . . . . . . . . . . . . . 55 32.1 32.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 33. Pinout and Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 33.1 33.2 Alternate Pin Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Alternate Pin Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 34. Peripheral Module Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 35. Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 36. Packaging information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 36.1 36.2 100A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 100C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 iii 36.3 100C2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 37. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 37.1 37.2 ATxmega64A1U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 ATxmega128A1U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 38. Typical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 38.1 38.2 ATxmega64A1U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 ATxmega128A1U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 39. Errata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 39.1 39.2 ATxmega64A1U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 ATxmega128A1U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 40. Datasheet Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 40.1 40.2 40.3 40.4 40.5 40.6 40.7 8385G - 11/2013 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8385F - 12/2012. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8385E - 11/2012. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8385D - 07/2012 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8385C - 07/2012 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8385B - 03/2012. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8385A - 11/2011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 208 208 208 208 209 209 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i XMEGA A1U [DATASHEET] 8385G-AVR-11/2013 iv Atmel Corporation 1600 Technology Drive Atmel Asia Limited Unit 01-5 & 16, 19F Atmel Munich GmbH Business Campus Atmel Japan G.K. 16F Shin-Osaki Kangyo Bldg San Jose, CA 95110 BEA Tower, Millennium City 5 Parkring 4 1-6-4 Osaki, Shinagawa-ku USA 418 Kwun Tong Roa D-85748 Garching b. Munich Tokyo 141-0032 Tel: (+1) (408) 441-0311 Kwun Tong, Kowloon GERMANY JAPAN Fax: (+1) (408) 487-2600 HONG KONG Tel: (+49) 89-31970-0 Tel: (+81) (3) 6417-0300 www.atmel.com Tel: (+852) 2245-6100 Fax: (+49) 89-3194621 Fax: (+81) (3) 6417-0370 Fax: (+852) 2722-1369 (c) 2012 Atmel Corporation. All rights reserved. / Rev.: 8385G-AVR-11/2013 Atmel(R), Atmel logo and combinations thereof, Enabling Unlimited Possibilities(R), and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.