CS5381 120 dB, 192 kHz, Multi-Bit Audio A/D Converter Features General Description ! Advanced Multi-bit Delta-Sigma Architecture The CS5381 is a complete analog-to-digital converter for digital audio systems. It performs sampling, analogto-digital conversion, and anti-alias filtering - generating 24-bit values for both left and right inputs in serial form at sample rates up to 216 kHz per channel. ! 24-bit Conversion ! 120 dB Dynamic Range ! -110 dB THD+N The CS5381 uses a 5th-order, multi-bit delta-sigma modulator followed by digital filtering and decimation, which removes the need for an external anti-alias filter. The ADC uses a differential architecture which provides excellent noise rejection. ! Supports All Audio Sample Rates Including 192 kHz ! 260 mW Power Consumption ! High-Pass Filter or DC Offset Calibration The CS5381 is available in 24-pin TSSOP and SOIC packages for Commercial grade (-10 to +70 C). The CDB5381 Customer Demonstration board is also available for device evaluation and implementation suggestions. Please refer to the "Ordering Information" on page 22. ! Supports Logic Levels between 5 and 2.5 V ! Differential Analog Architecture ! Low-Latency Digital Filtering ! Overflow Detection ! Pin-Compatible with the CS5361 Analog Supply 5V The CS5381 is ideal for audio systems requiring wide dynamic range, negligible distortion, and low noise such as A/V receivers, DVD-R, CD-R, digital mixing consoles, and effects processors. Digital Supply 3.3 V to 5 V Interface Supply 2.5 V to 5 V Internal Voltage Reference Differential Inputs Switch-Cap ADC http://www.cirrus.com Digital Filters Digital Filters Copyright (c) Cirrus Logic, Inc. 2005 (All Rights Reserved) Level Translator Differential Inputs Switch-Cap ADC Reset Mode Configuration HPF OVFL PCM Serial Audio Output JULY '05 DS563F2 CS5381 TABLE OF CONTENTS 1. PIN DESCRIPTIONS ............................................................................................................................... 4 2. CHARACTERISTICS AND SPECIFICATIONS....................................................................................... 5 SPECIFIED OPERATING CONDITIONS .................................................................................................... 5 ABSOLUTE MAXIMUM RATINGS............................................................................................................... 5 ANALOG CHARACTERISTICS (CS5381-KSZ/-KZZ).................................................................................. 6 DIGITAL FILTER CHARACTERISTICS....................................................................................................... 7 SWITCHING CHARACTERISTICS - SERIAL AUDIO PORT .................................................................... 10 DC ELECTRICAL CHARACTERISTICS.................................................................................................... 13 DIGITAL CHARACTERISTICS .................................................................................................................. 13 THERMAL CHARACTERISTICS .............................................................................................................. 13 TYPICAL CONNECTION DIAGRAM ......................................................................................................... 14 3. APPLICATIONS .................................................................................................................................... 15 3.1 Operational Mode/Sample Rate Range Select.............................................................................. 15 3.2 System Clocking ............................................................................................................................ 15 3.2.1 Master Mode ........................................................................................................................ 15 3.2.2 Slave Mode .......................................................................................................................... 16 3.3 Power-Up Sequence ..................................................................................................................... 16 3.4 Analog Connections ...................................................................................................................... 16 3.5 High-Pass Filter and DC Offset Calibration .................................................................................. 17 3.6 Overflow Detection ........................................................................................................................ 18 3.6.1 OVFL Configuration ............................................................................................................. 18 3.6.2 OVFL Output Timing ............................................................................................................ 18 3.7 Grounding and Power Supply Decoupling..................................................................................... 18 3.8 Synchronization of Multiple Devices .............................................................................................. 18 3.9 Capacitor Size on the Reference Pin (FILT+)................................................................................ 19 4. PACKAGE DIMENSIONS ..................................................................................................................... 20 5. ORDERING INFORMATION ................................................................................................................. 22 7. REVISION HISTORY ............................................................................................................................. 24 2 DS563F2 CS5381 LIST OF FIGURES Figure 1. Single-Speed Mode Stopband Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Single-Speed Mode Transition Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 3. Single-Speed Mode Transition Band (Detail). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 4. Single-Speed Mode Passband Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 5. Double-Speed Mode Stopband Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 6. Double-Speed Mode Transition Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 7. Double-Speed Mode Transition Band (Detail) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 8. Double-Speed Mode Passband Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 9. Quad-Speed Mode Stopband Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 10. Quad-Speed Mode Transition Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 11. Quad-Speed Mode Transition Band (Detail) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 12. Quad-Speed Mode Passband Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 13. Master Mode, Left-Justified SAI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 14. Slave Mode, Left-Justified SAI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 15. Master Mode, IS SAI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 16. Slave Mode, IS SAI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 17. OVFL Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 18. Left-Justified Serial Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 19. IS Serial Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 20. OVFL Output Timing, IS Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 21. OVFL Output Timing, Left-Justified Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 22. Typical Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 23. CS5381 Master Mode Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 24. Recommended Analog Input Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 25. CS5381 THD + N versus Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 LIST OF TABLES Table 1. CS5381 Mode Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 2. CS5381 Common Master Clock Frequencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 3. CS5381 Slave Mode Clock Ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DS563F2 3 CS5381 1. PIN DESCRIPTIONS RST M/S LRCK SCLK MCLK VD GND VL SDOUT MDIV HPF IS/LJ Pin Name 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 FILT+ REFGND VQ AINR+ AINRVA GND AINLAINL+ OVFL M1 M0 # Pin Description RST 1 Reset (Input) - The device enters a low power mode when low. M/S 2 Master/Slave Mode (Input) - Selects operation as either clock master or slave. LRCK 3 Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on the serial audio data line. SCLK 4 Serial Clock (Input/Output) - Serial clock for the serial audio interface. MCLK 5 Master Clock (Input) - Clock source for the delta-sigma modulator and digital filters. VD 6 Digital Power (Input) - Positive power supply for the digital section. GND 7,18 Ground (Input) - Ground reference. Must be connected to analog ground. VL 8 Logic Power (Input) - Positive power for the digital input/output. SDOUT 9 Serial Audio Data Output (Output) - Output for two's complement serial audio data. MDIV 10 MCLK Divider (Input) - Enables a master clock divide by two function. HPF 11 High-Pass Filter Enable (Input) - Enables the Digital High-Pass Filter. IS/LJ 12 Serial Audio Interface Format Select (Input) -Selects either the left-justified or IS format for the SAI. M0 M1 13,14 Mode Selection (Input) - Determines the operational mode of the device. OVFL 15 AINL+ AINL- 16, 17 VA AINRAINR+ 19 20, 21 Overflow (Output, open drain) - Detects an overflow condition on both left and right channels. Differential Left Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma modulators via the AINL+/- pins. Analog Power (Input) - Positive power supply for the analog section. Differential Right Channel Analog Input (Input) -Signals are presented differentially to the deltasigma modulators via the AINR+/- pins. VQ 22 Quiescent Voltage (Output) - Filter connection for the internal quiescent reference voltage. REF_GND 23 Reference Ground (Input) - Ground reference for the internal sampling circuits. FILT+ 24 Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits. 4 DS563F2 CS5381 2. CHARACTERISTICS AND SPECIFICATIONS All Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical performance characteristics and specifications are derived from measurements taken at VA = 5.0 V, VD = VL = 3.3 V, and TA = 25C. SPECIFIED OPERATING CONDITIONS (GND = 0 V; all voltages with respect to 0 V.) Parameters Symbol Min Typ Max Units VA VD VL 4.75 3.1 2.37 5.0 - 5.25 5.25 5.25 V V V TA -10 - +70 C DC Power Supply DC Power Supplies: Positive Analog Positive Digital Positive Logic Ambient Operating Temperature (Power Applied) ABSOLUTE MAXIMUM RATINGS (GND = 0 V, All voltages with respect to ground.) (Note 1) Parameter Symbol Min Typ Max Units Analog Logic Digital VA VL VD -0.3 -0.3 -0.3 - +6.0 +6.0 +6.0 V V V Input Current (Note 2) Iin -10 - +10 mA Analog Input Voltage (Note 3) VIN GND-0.7 - VA+0.7 V Digital Input Voltage (Note 3) VIND -0.7 - VL+0.7 V TA -50 - +95 C Tstg -65 - +150 C DC Power Supplies: Ambient Operating Temperature (Power Applied) Storage Temperature Notes: 1. Operation beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. 2. Any pin except supplies. Transient currents of up to 100 mA on the analog input pins will not cause SRC latch-up. 3. The maximum over/under voltage is limited by the input current. DS563F2 5 CS5381 ANALOG CHARACTERISTICS (CS5381-KSZ/-KZZ) Test conditions (unless otherwise specified): Input test signal is a 1 kHz sine wave; measurement bandwidth is 10 Hz to 20 kHz. Parameter Single-Speed Mode Symbol Dynamic Range A-weighted unweighted Total Harmonic Distortion + Noise Double-Speed Mode Max Unit 114 111 120 117 - dB dB THD+N - -110 -97 -57 -104 - dB dB dB 114 111 - 120 117 114 - dB dB dB - -110 -97 -57 -107 -104 - dB dB dB dB 114 111 - 120 117 114 - dB dB dB - -110 -97 -57 -107 -104 - dB dB dB dB - 110 - dB -5 - 0.1 100 0 100 5 - dB % ppm/C LSB LSB 1.07*VA - 1.13*VA 2.5 100 1.18*VA - Vpp k dB Fs = 96 kHz A-weighted unweighted 40 kHz bandwidth unweighted Total Harmonic Distortion + Noise (Note 4) -1 dB -20 dB -60 dB -1 dB 40 kHz bandwidth Quad-Speed Mode Dynamic Range Typ (Note 4) -1 dB -20 dB -60 dB Dynamic Range Min Fs = 48 kHz THD+N Fs = 192 kHz A-weighted unweighted 40 kHz bandwidth unweighted Total Harmonic Distortion + Noise (Note 4) -1 dB -20 dB -60 dB -1 dB 40 kHz bandwidth THD+N Dynamic Performance for All Modes Interchannel Isolation DC Accuracy Interchannel Gain Mismatch Gain Error Gain Drift Offset Error HPF enabled HPF disabled Analog Input Characteristics Full-scale Input Voltage Input Impedance (Differential) (Note 5) Common Mode Rejection Ratio CMRR 4. Referred to the typical full-scale input voltage. 5. Measured between AIN+ and AIN-. 6 DS563F2 CS5381 DIGITAL FILTER CHARACTERISTICS Parameter Symbol Min Typ Max Unit 0 - 0.47 Fs -0.1 - 0.035 dB 0.58 - - Fs -95 - - dB - 12/Fs - s (Note 6) 0 - 0.45 Fs -0.1 - 0.035 dB (Note 6) 0.68 - - Fs -92 - - dB - 9/Fs - s 0 - 0.24 Fs -0.1 - 0.035 dB 0.78 - - Fs -97 - - dB - 5/Fs - s - 1 20 - Hz Hz - 10 - Deg - - 0 dB Single-Speed Mode (2 kHz to 54 kHz sample rates) Passband (-0.1 dB) (Note 6) Passband Ripple Stopband (Note 6) Stopband Attenuation tgd Total Group Delay (Fs = Output Sample Rate) Double-Speed Mode (50 kHz to 108 kHz sample rates) Passband (-0.1 dB) Passband Ripple Stopband Stopband Attenuation tgd Total Group Delay (Fs = Output Sample Rate) Quad-Speed Mode (100 kHz to 216 kHz sample rates) Passband (-0.1 dB) (Note 6) Passband Ripple Stopband (Note 6) Stopband Attenuation tgd Total Group Delay (Fs = Output Sample Rate) High-Pass Filter Characteristics Frequency Response Phase Deviation -3.0 dB -0.13 dB (Note 7) @ 20 Hz (Note 7) Passband Ripple Filter Setting Time 105/Fs s 6. The filter frequency response scales precisely with Fs. 7. Response shown is for Fs equal to 48 kHz. Filter characteristics scale with Fs. DS563F2 7 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 Amplitude (dB) Amplitude (dB) CS5381 -60 -70 -80 -60 -70 -80 -90 -90 -100 -100 -110 -110 -120 -120 -130 -130 -140 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Frequency (normalized to Fs) -140 0.40 0.42 0.44 0.46 0.48 0.50 0.52 0.54 0.56 0.58 0.60 Frequency (normalized to Fs) Figure 1. Single-Speed Mode Stopband Rejection Figure 2. Single-Speed Mode Transition Band 0 0.10 -1 0.08 -2 0.05 0.03 -4 Amplitude (dB) Amplitude (dB) -3 -5 -6 0.00 -0.03 -7 -0.05 -8 -0.08 -9 -10 0.45 0.46 0.47 0.48 0.49 0.50 0.51 0.52 0.53 0.54 -0.10 0.00 0.55 0.05 0.10 0.15 0.20 Frequency (normalized to Fs) 0.25 0.30 0.35 0.40 0.45 0.50 Frequency (normalized to Fs) Figure 3. Single-Speed Mode Transition Band (Detail) Figure 4. Single-Speed Mode Passband Ripple 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 Amplitude (dB) Amplitude (dB) -50 -60 -70 -80 -60 -70 -80 -90 -90 -100 -100 -110 -110 -120 -120 -130 -130 -140 0.40 -140 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0.43 0.45 0.48 0.50 0.53 0.55 0.58 0.60 0.63 0.65 0.68 0.70 Frequency (normalized to Fs) Frequency (normalized to Fs) Figure 5. Double-Speed Mode Stopband Rejection 8 Figure 6. Double-Speed Mode Transition Band DS563F2 CS5381 0 0.10 -1 0.08 -2 0.05 0.03 -4 Amplitude (dB) Amplitude (dB) -3 -5 -6 0.00 -0.03 -7 -0.05 -8 -0.08 -9 -10 0.40 0.43 0.45 0.48 0.50 0.53 0.55 -0.10 0.00 0.05 0.10 0.15 0.20 Frequency (normalized to Fs) 0.25 0.30 0.35 0.40 0.45 0.50 Frequency (normalized to Fs) Figure 7. Double-Speed Mode Transition Band (Detail) Figure 8. Double-Speed Mode Passband Ripple 0 0 -10 -10 -20 -20 -30 -30 -40 Amplitude (dB) Amplitude (dB) -40 -50 -60 -70 -50 -60 -70 -80 -80 -90 -90 -100 -100 -110 -110 -120 -130 -120 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0.2 1.0 0.25 0.3 0 0.10 -1 0.08 -2 0.06 -3 0.04 -4 0.02 -5 -6 -8 -0.06 -9 -0.08 -10 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 Frequency (normalized to Fs) Figure 11. Quad-Speed Mode Transition Band (Detail) DS563F2 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.00 -0.04 0.2 0.45 -0.02 -7 0.15 0.4 Figure 10. Quad-Speed Mode Transition Band Amplitude (dB) Amplitude (dB) Figure 9. Quad-Speed Mode Stopband Rejection 0.1 0.35 Frequency (normalized to Fs) Frequency (normalized to Fs) -0.10 0.00 0.05 0.10 0.15 0.20 0.25 Frequency (normalized to Fs) Figure 12. Quad-Speed Mode Passband Ripple 9 CS5381 SWITCHING CHARACTERISTICS - SERIAL AUDIO PORT (Logic "0" = GND = 0 V; Logic "1" = VL, CL = 20 pF) Parameter Symbol Min Typ Max Unit Fs Fs Fs 2 50 100 - 54 108 216 kHz kHz kHz OVFL to LRCK Edge Setup Time tsetup 16/fsclk - - s OVFL to LRCK Edge Hold Time thold 1/fsclk - - s - 740 680 - ms ms 36 - 1953 ns 40 - 60 % - 20 ns Output Sample Rate Single-Speed Mode Double-Speed Mode Quad-Speed Mode OVFL time-out on overrange condition Fs = 44.1, 88.2, 176.4 kHz Fs = 48, 96, 192 kHz MCLK Specifications MCLK Period tclkw MCLK Duty Cycle Master Mode SCLK falling to LRCK transition tmslr -20 SCLK falling to SDOUT valid tsdo - - 32 ns - 50 - % SCLK Duty Cycle Slave Mode Single-Speed Output Sample Rate Fs LRCK Duty Cycle SCLK Period tsclkw SCLK Duty Cycle 2 - 54 kHz 40 50 60 % 145 - - ns 45 50 55 % SDOUT valid before SCLK rising tstp 10 - - ns SDOUT valid after SCLK rising thld 5 - - ns SCLK falling to LRCK transition tslrd -20 - 20 ns Fs 50 - 108 kHz 40 50 60 % 145 - - ns 45 50 55 % Double-Speed Output Sample Rate LRCK Duty Cycle SCLK Period tsclkw SCLK Duty Cycle SDOUT valid before SCLK rising tstp 10 - - ns SDOUT valid after SCLK rising thld 5 - - ns SCLK falling to LRCK transition tslrd -20 - 20 ns Fs 100 - 216 kHz 40 50 60 % 72 - - ns 45 50 55 % Quad-Speed Output Sample Rate LRCK Duty Cycle SCLK Period tsclkw SCLK Duty Cycle SDOUT valid before SCLK rising tstp 10 - - ns SDOUT valid after SCLK rising thld 5 - - ns SCLK falling to LRCK transition tslrd -8 - 8 ns 10 DS563F2 CS5381 LRCK input LRCK output t slrd tmslr SCLK input SCLK output t sclkh t sdo SDOUT MSB MSB-1 MSB-2 MSB-3 SDOUT Figure 13. Master Mode, Left-Justified SAI MSB MSB-1 Figure 14. Slave Mode, Left-Justified SAI LRCK input LRCK output t slrd tmslr SCLK input SCLK output t sclkh MSB MSB-1 MSB-2 MSB-3 t sclkl t stp t hld t sdo SDOUT t sclkl t stp t hld SDOUT Figure 15. Master Mode, IS SAI MSB Figure 16. Slave Mode, IS SAI LRCK t setup t hold OVFL Figure 17. OVFL Output Timing DS563F2 11 CS5381 LRCK Left Channel Right Channel SCLK SDATA 23 22 9 8 7 6 5 4 3 2 1 0 23 22 9 8 7 6 5 4 3 2 1 0 23 22 23 22 Figure 18. Left-Justified Serial Audio Interface LRCK Left Channel Right Channel SCLK SDATA 23 22 9 8 7 6 5 4 3 2 1 0 23 22 9 8 7 6 5 4 3 2 1 0 Figure 19. IS Serial Audio Interface Left Channel Frame LRCK Right Channel Frame SCLK OVFL OVFL on Left Chan OVFL on Right Chan Figure 20. OVFL Output Timing, IS Format LRCK R ig h t C h a n n e l F r a m e L e ft C h a n n e l F r a m e SC LK OVFL O V F L o n R ig h t C h a n O V F L o n L e ft C han Figure 21. OVFL Output Timing, Left-Justified Format 12 DS563F2 CS5381 DC ELECTRICAL CHARACTERISTICS (GND = 0 V, all voltages with respect to ground. MCLK=12.288 MHz; Master Mode) Parameter Symbol Min Typ Max Unit VA = 5 V VL,VD = 5 V VL,VD = 3.3 V IA ID ID - 36 36 24 43 46 28 mA mA mA VA = 5 V VL,VD = 5 V IA ID - 100 100 - uA uA VA, VL, VD = 5 V VA = 5 V; VL, VD = 3.3 V (Power-Down Mode) - - 360 260 1 445 307 - mW mW mW PSRR - 65 - dB - 2.5 25 0.01 - V k mA - 5 4.5 0.01 - V k mA Power Supply Current (Normal Operation) Power Supply Current (Power-Down Mode) (Note 8) Power Consumption (Normal Operation) Power Supply Rejection Ratio (1 kHz) (Note 9) VQ Nominal Voltage Output Impedance Maximum allowable DC current source/sink Filt+ Nominal Voltage Output Impedance Maximum allowable DC current source/sink 8. Power-Down Mode is defined as RST = Low with all clocks and data lines held static. 9. Valid with the recommended capacitor values on FILT+ and VQ as shown in the Typical Connection Diagram. DIGITAL CHARACTERISTICS Parameter Symbol Min Typ Max Units VIH 70% - - V High-Level Input Voltage (% of VL) Low-Level Input Voltage (% of VL) VIL - - 30% V High-Level Output Voltage at Io = 100 A (% of VL) VOH 70% - - V Low-Level Output Voltage at Io = 100 A (% of VL) VOL - - 15% V Iovfl - - 4.0 mA Iin -10 - 10 A OVFL Current Sink Input Leakage Current THERMAL CHARACTERISTICS Parameter Symbol Allowable Junction Temperature Junction to Ambient Thermal Impedance (Multi-layer PCB) TSSOP (Multi-layer PCB) SOIC (Single-layer PCB) TSSOP (Single-layer PCB) SOIC DS563F2 JA-TM JA-SM JA-TS JA-SS Min Typ Max Unit - - 135 C - 70 60 105 80 - C/W C/W C/W C/W 13 CS5381 TYPICAL CONNECTION DIAGRAM +5 V to 3.3 V +5V + 1 F 0.01 F 0.01F * + 1 F VA VD VL FILT+ **47 F + VL 0.01 F 10 k REFGND + 1 F 0.01 F VQ Analog Input Buffer (Figure 24) +5Vto 2.5 V 1 F 0.01 F 5.1 0.01 F + AINL+ CS5381 A/D CONVERTER OVFL RST 2 I S/LJ M/S HPF M0 M1 MDIV Power Down and Mode Settings SDOUT Audio Data Processor AINL- Analog Input Buffer (Figure 24) AINR+ LRCK Timing Logic and Clock SCLK MCLK AINR- * Resistor may only be used if VD is derived from VA. If used, do not drive any other logic from VD. GND GND ** Capacitor value affects low frequency distortion. See Section 3.9. Figure 22. Typical Connection Diagram 14 DS563F2 CS5381 3. APPLICATIONS 3.1 Operational Mode/Sample Rate Range Select The output sample rate, Fs, can be adjusted from 2 kHz to 216 kHz. The CS5381 must be set to the proper speed mode via the mode pins, M1 and M0. Refer to Table 1. M1 (Pin 14) 0 0 1 1 M0 (Pin 13) 0 1 0 1 MODE Output Sample Rate (Fs) Single-Speed Mode Double-Speed Mode Quad-Speed Mode Reserved 2 kHz - 54 kHz 50 kHz - 108 kHz 100 kHz - 216 kHz Table 1. CS5381 Mode Control 3.2 System Clocking The device supports operation in either Master Mode, where the left/right and serial clocks are synchronously generated on-chip, or Slave Mode, which requires external generation of the left/right and serial clocks. The device also includes a master clock divider in Master Mode where the master clock will be internally divided prior to any other internal circuitry when MDIV is enabled, set to logic 1. In Slave Mode, the MDIV pin needs to be disabled, set to logic 0. 3.2.1 Master Mode In Master mode, LRCK and SCLK operate as outputs. The left/right and serial clocks are internally derived from the master clock with the left/right clock equal to Fs and the serial clock equal to 64x Fs, as shown in Figure 23. Refer to Table 2 for common master clock frequencies. /1 / 256 Single Speed 00 / 128 Double Speed 01 / 64 Quad Speed 10 LRCK Output (Equal to Fs) 0 M1 M0 MCLK /2 1 MDIV /4 Single Speed 00 /2 Double Speed 01 /1 Quad Speed 10 SCLK Output Figure 23. CS5381 Master Mode Clocking DS563F2 15 CS5381 SAMPLE RATE (kHz) MDIV = 0 MCLK (MHz) MDIV = 1 MCLK (MHz) 32 44.1 48 64 88.2 96 176.4 192 8.192 11.2896 12.288 8.192 11.2896 12.288 11.2896 12.288 16.384 22.5792 24.576 16.384 22.5792 24.576 22.5792 24.576 Table 2. CS5381 Common Master Clock Frequencies 3.2.2 Slave Mode LRCK and SCLK operate as inputs in Slave mode. It is recommended that the left/right clock be synchronously derived from the master clock and must be equal to Fs. It is also recommended that the serial clock be synchronously derived from the master clock and be equal to 64x Fs to maximize system performance. Refer to Table 3 for required clock ratios. Single-Speed Mode Double-Speed Mode Quad-Speed Mode Fs = 2 kHz to 54 kHz Fs = 50 kHz to 108 kHz Fs = 100 kHz to 216 kHz MCLK/LRCK Ratio 256x, 512x 128x, 256x 64x*, 128x SCLK/LRCK Ratio 64x, 128x 64x 64x * Only available in Master mode. Table 3. CS5381 Slave Mode Clock Ratios 3.3 Power-Up Sequence Reliable power-up can be accomplished by keeping the device in reset until the power supplies, clocks and configuration pins are stable. It is also recommended that reset be enabled if the analog or digital supplies drop below the minimum specified operating voltages to prevent power glitch related issues. The internal reference voltage must be stable for the device to produce valid data. Therefore, there is a delay between the release of reset and the generation of valid output, due to the finite output impedance of FILT+ and the presence of the external capacitance. This duration of this delay is less than 2500 LRCK cycles. 3.4 Analog Connections The analog modulator samples the input at 6.144 MHz. The digital filter will reject signals within the stopband of the filter. However, there is no rejection for input signals which are (n x 6.144 MHz) the digital passband frequency, where n=0,1,2,... Refer to Figure 24, which shows the suggested filter that will attenuate any noise energy at 6.144 MHz in addition to providing the optimum source impedance for the modulators. The use of capacitors which have a large voltage coefficient (such as general purpose ceramics) must be avoided since these can degrade signal linearity. C0G capacitors are recommended for this application. 16 DS563F2 CS5381 634 470 pF COG 91 10 uF ADC AIN+ + AIN+ 100k 10 k COG VQ 2700 pF 10 k 10 uF AIN- + 100k - 91 ADC AIN- 470 pF COG 634 Figure 24. Recommended Analog Input Buffer 3.5 High-Pass Filter and DC Offset Calibration The operational amplifiers in the input circuitry driving the CS5381 may generate a small DC offset into the A/D converter. The CS5381 includes a high-pass filter after the decimator to remove any DC offset which could result in recording a DC level, possibly yielding "clicks" when switching between devices in a multichannel system. The high-pass filter continuously subtracts a measure of the DC offset from the output of the decimation filter. If the HPF pin is taken high during normal operation, the current value of the DC offset register is frozen and this DC offset will continue to be subtracted from the conversion result. This feature makes it possible to perform a system DC offset calibration by: 1. Running the CS5381 with the high-pass filter enabled until the filter settles. See the Digital Filter Characteristics for filter settling time. 2. Disabling the high-pass filter and freezing the stored DC offset. A system calibration performed in this way will eliminate offsets anywhere in the signal path between the calibration point and the CS5381. DS563F2 17 CS5381 3.6 Overflow Detection The CS5381 includes overflow detection on both the left and right channels. This time multiplexed information is presented as open drain, active low on pin 15, OVFL. The OVFL_L and OVFL_R data will go to a logical low as soon as an overrange condition in the opposite channel is detected. The data will remain low as specified in the "Switching Characteristics - Serial Audio Port" section on page 10. This ensures sufficient time to detect an overrange condition regardless of the speed mode. After the timeout, the OVFL_L and OVFL_R data will return to a logical high if there has not been any other overrange condition detected. Please note that an overrange condition on either channel will restart the timeout period for both channels. 3.6.1 OVFL Configuration If the system does not require overflow detection, the user may leave the OVFL pin disconnected. When using the overflow detection capability of the CS5381, a 10 k pull-up resistor must be inserted between the OVFL pin and VL because the OVFL output is open drain, active low. This means that the OVFL pin is high impedance for the case of no overflow condition, but the pull-up resistor will pull the node to VL. When an overflow condition occurs, the OVFL pin can drive the node to GND thus indicating the presence of the overflow condition. In effect, the user can use the OVFL pin to illuminate an LED, or mute the channel with an external circuit or a DSP. Furthermore, because the OVFL output is open-drain, the OVFL pins of multiple CS5381 devices can be tied together such that an overflow condition on a single device will drive the line low. When connecting OVFL pins of multiple devices, only a single 10k pull-up resistor is necessary. 3.6.2 OVFL Output Timing In left-justified format, the OVFL pin is updated one SCLK period after an LRCK transition. In IS format, the OVFL pin is updated two SCLK periods after an LRCK transition. Refer to Figures 20 and 21. In both cases, the OVFL data can be easily demultiplexed by using the LRCK to latch the data. In left-justified format, the rising edge of LRCK would latch the right channel overflow status, and the falling edge of LRCK would latch the left channel overflow status. In IS format, the falling edge of LRCK would latch the right channel overflow status and the rising edge of LRCK would latch the left channel overflow status. 3.7 Grounding and Power Supply Decoupling As with any high resolution converter, the CS5381 requires careful attention to power supply and grounding arrangements if its potential performance is to be realized. Figure 22 shows the recommended power arrangements, with VA and VL connected to clean supplies. VD, which powers the digital filter, may be run from the system logic supply or may be powered from the analog supply via a resistor. In this case, no additional devices should be powered from VD. Decoupling capacitors should be as near to the ADC as possible, with the low value ceramic capacitor being the nearest. All signals, especially clocks, should be kept away from the FILT+ and VQ pins in order to avoid unwanted coupling into the modulators. The FILT+ and VQ decoupling capacitors, particularly the 0.01 F, must be positioned to minimize the electrical path from FILT+ and REFGND. The CDB5381 evaluation board demonstrates the optimum layout and power supply arrangements. To minimize digital noise, connect the ADC digital outputs only to CMOS inputs. 3.8 Synchronization of Multiple Devices In systems where multiple ADCs are required, care must be taken to achieve simultaneous sampling. To ensure synchronous sampling, the MCLK and LRCK must be the same for all of the CS5381's in the system. If only one master clock source is needed, one solution is to place one CS5381 in Master mode, and slave all of the other CS5381's to the one master. If multiple master clock sources are needed, a possible solution would be to supply all clocks from the same external source and time the CS5381 reset with the falling edge of MCLK. This will ensure that all converters begin sampling on the same clock edge. 18 DS563F2 CS5381 3.9 Capacitor Size on the Reference Pin (FILT+) The CS5381 requires an external capacitance on the internal reference voltage pin, FILT+. The size of this decoupling capacitor will affect the low frequency distortion performance as shown in Figure 25, with larger capacitor values used to optimize low frequency distortion performance. The THD+N curves in Figure 25 were measured with VA=VD=VL=5 V in Single-Speed Master Mode with a full-scale sinewave input. 1 uF 10 uF 22 uF 47 uF 100 uF 220 uF Figure 25. CS5381 THD + N versus Frequency DS563F2 19 CS5381 4. PACKAGE DIMENSIONS 24L SOIC (300 MIL BODY) PACKAGE DRAWING E H 1 b c D L SEATING PLANE A e A1 INCHES DIM MIN MAX A A1 B C D E e H L 0.093 0.004 0.013 0.009 0.598 0.291 0.040 0.394 0.016 0 0.104 0.012 0.020 0.013 0.614 0.299 0.060 0.419 0.050 8 20 MILLIMETERS MIN MAX 2.35 0.10 0.33 0.23 15.20 7.40 1.02 10.00 0.40 0 2.65 0.30 0.51 0.32 15.60 7.60 1.52 10.65 1.27 8 DS563F2 CS5381 24L TSSOP (4.4 mm BODY) PACKAGE DRAWING N D E11 A2 E A e b2 SIDE VIEW A1 L END VIEW SEATING PLANE 1 2 3 TOP VIEW DIM MIN INCHES NOM MAX MIN MILLIMETERS NOM MAX NOTE A A1 A2 b D E E1 e L -0.002 0.03346 0.00748 0.303 0.248 0.169 -0.020 0 -0.004 0.0354 0.0096 0.307 0.2519 0.1732 0.026 BSC 0.024 4 0.043 0.006 0.037 0.012 0.311 0.256 0.177 -0.028 8 -0.05 0.85 0.19 7.70 6.30 4.30 -0.50 0 --0.90 0.245 7.80 6.40 4.40 0.65 BSC 0.60 4 1.10 0.15 0.95 0.30 7.90 6.50 4.50 -0.70 8 2,3 1 1 JEDEC #: MO-153 Controlling Dimension is Millimeters. Notes: 1. "D" and "E1" are reference datums and do not included mold flash or protrusions, but do include mold mismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20 mm per side. 2. Dimension "b" does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be 0.13 mm total in excess of "b" dimension at maximum material condition. Dambar intrusion shall not reduce dimension "b" by more than 0.07 mm at least material condition. 3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips. DS563F2 21 CS5381 5. ORDERING INFORMATION Product Description Package Pb-Free Grade Temp Range CS5381 120 dB, 192 kHz, Multi-Bit 24-TSSOP Audio A/D Converter Yes Commercial -10 to +70 C CS5381 120 dB, 192 kHz, Multi-Bit Audio A/D Converter 24-SOIC Yes Commercial -10 to +70 C - - CDB5381 CS5381 Evaluation Board 22 - - Container Order # Bulk CS5381-KZZ Tape & Reel CS5381-KZZR Bulk CS5381-KSZ Tape & Reel CS5381-KSZR - CDB5381 DS563F2 CS5381 6 PARAMETER DEFINITIONS Dynamic Range The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth. Dynamic Range is a signal-to-noise ratio measurement over the specified bandwidth made with a -60 dBFS signal. 60 dB is added to resulting measurement to refer the measurement to full-scale. This technique ensures that the distortion components are below the noise level and do not affect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307. Expressed in decibels. Total Harmonic Distortion + Noise The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Measured at -1 and -20 dBFS as suggested in AES17-1991 Annex A. Frequency Response A measure of the amplitude response variation from 10 Hz to 20 kHz relative to the amplitude response at 1 kHz. Units in decibels. Interchannel Isolation A measure of crosstalk between the left and right channels. Measured for each channel at the converter's output with no signal to the input under test and a full-scale signal applied to the other channel. Units in decibels. Interchannel Gain Mismatch The gain difference between left and right channels. Units in decibels. Gain Error The deviation from the nominal full-scale analog input for a full-scale digital output. Gain Drift The change in gain value with temperature. Units in ppm/C. Offset Error The deviation of the mid-scale transition (111...111 to 000...000) from the ideal. Units in mV. DS563F2 23 CS5381 7. REVISION HISTORY Release A1 A2 Date December 2002 Initial Release October 2003 Changes Changed front page description of digital filter Improved distortion specification from -105 dB to -110 dB Modified serial port timing specifications for slave mode operation Added pull-down resistors to recommended input buffer Changed full-scale voltage specification to reflect VA supply voltage Added Applications section about capacitor value on FILT+ pin Changed input impedance specification from 37 to 2.5 k Changed impedance specification on FILT+ from 35 to 4.5 k A3 May 2004 A4 August 2004 F1 July 2005 Replaced diagrams showing OVFL functionality (see Figures 20 and 21) Replaced Figures 13, 15, 18 and 19 to demonstrate pre-emption of the MSB. Increased maximum digital current (ID) specification at 5 V from 43 mA to 46 mA. . F2 July 2005 Updated Ordering Information. Add Lead free part number Contacting Cirrus Logic Support For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find the one nearest to you go to www.cirrus.com IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. 24 DS563F2