4. SPECIFICATIONS FOR EACH SERIES Conductive polymer type SEQP 125C guaranteed, 32V product Series Marking : Polarity( ), Rated voltage (Purple) SEQP, Rated capacitance, Lot.No. Specifications Items Category temperature range Tolerance on rated capacitance Tangent of loss angle Leakage current 1 ESR Characteristics of impedance ratio at high temp. and low temp. Conditions 120Hz 120Hz After 2 minutes Based the value at 100KHz+20C Endurance 125C, 1,000h, Rated voltage applied Damp heat (Steady state) 60C, 90 to 95% RH, 1,000h, No-applied voltage Resistance to soldering heat Flow method (2605C X 10s) Characteristics -55C to +125C M : 20% Less than or equal to the value of Table6 Less than or equal to the value of Table6 Less than or equal to the value of Table6 Z / Z 20C 0.75 to 1.25 -55C 0.75 to 1.25 Z / Z 20C +125C Within 20% C/C 2 times or less than an initial standard tan 2 times or less than an initial standard ESR Leakage current Below an initial standard Within 20% C/C 1.5 times or less than an initial standard tan 1.5 times or less than an initial standard ESR Leakage current Below an initial standard (after voltage processing) Within 5% C/C Below an initial standard tan Below an initial standard ESR Leakage current Below an initial standard (after voltage processing) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125C . Dimensions (unit : mm) d Size Code D+0.5max. Lmax. F d0.05 C6 E7 F8 E12 F13 6.3 8.0 10.0 8.0 10.0 6.0 7.0 8.0 12.0 13.0 2.50.5 3.50.5 5.00.5 3.50.5 5.00.5 0.45 0.45 0.50 0.60 0.60 F D Specifications for each series This series has advanced characteristics in resistance to heat compared with the SEP series, and adds a rated voltage of 32V. Suitable for use in increasing device reliability, 32V products may be used on 16 to 24V line industrial devices. Lead free-flow is supported. 15min. L 19min. Size List RV (SV) F 6.8 15 18 22 39 47 56 68 82 100 120 150 180 270 330 470 560 680 820 1200 4min. RV : Rated voltage 4.0 (5.2) 6.3 (8.4) 10 (11.5) (SV) : Surge (room temperature) 16 (18.4) 20 (23) E7 F8 E12 C6 C6 E7 C6 F8 E7 C6 E12 E7 C6 E7 E7 F8 E12 F8 E12 F8 E12 F13 F13 F13 E12 F8 F13 F13 For the minimum packing quantity, please refer to page 51. 32 32 (37) 4. SPECIFICATIONS FOR EACH SERIES Table6 SEQP Series Characteristics List Size Code Rated Voltage (V) Rated ripple current Allowable ripple current Tangent of Rated ESR Capacitance 100kHz to 300kHz loss angle 100kHz (mArms) 3 (F) (m) (max.) (max.) 105CTx125C Tx105C Leakage current (A) (max.)2 20SEQP22M 20 22 60 458 1450 0.10 220 16SEQP39M 16 39 50 512 1620 0.10 312 10SEQP56M 10 56 45 537 1700 0.12 280 82 45 537 1700 0.12 258 150 40 572 1810 0.12 300 100 440 1400 0.10 44 6SEQP82M 6.3 4SEQP150M 4 32SEQP6R8M 32 20SEQP47M 20 47 45 598 1890 0.12 470 16SEQP82M 16 82 40 670 2120 0.12 656 10SEQP120M 10 120 35 810 2560 0.12 600 6.8 Specifications for each series C6 Part Number 1 E7 6SEQP150M 6.3 150 35 810 2560 0.12 472 4SEQP330M 4 330 35 810 2560 0.12 660 32SEQP15M 32 15 80 560 1800 0.10 96 20SEQP68M 20 68 40 759 2400 0.12 272 16SEQP150M 16 150 30 955 3020 0.12 480 10SEQP270M 10 270 25 1170 3700 0.12 540 F8 E12 F13 1 2 3 6SEQP330M 6.3 330 25 1170 3700 0.12 416 4SEQP680M 4 680 25 1170 3700 0.12 544 32SEQP18M 32 18 50 790 2500 0.12 115 20SEQP100M 20 100 24 1050 3320 0.15 400 16SEQP180M 16 180 20 1151 3640 0.15 576 10SEQP330M 10 330 17 1250 3950 0.15 660 6SEQP470M 6.3 470 15 1332 4210 0.15 592 4SEQP560M 4 560 13 1430 4520 0.15 448 20SEQP150M 20 150 20 1367 4320 0.15 600 16SEQP330M 16 330 16 1493 4720 0.15 792 10SEQP560M 10 560 13 1655 5230 0.15 840 820 12 1721 5440 0.15 775 1200 12 1721 5440 0.18 960 6SEQP820M 6.3 4SEQP1200M 4 Capacitance tolerance : M 20% After 2 minutes Tx : Ambient temperature Frequency coefficient for ripple current Frequency Coefficient 120Hz f 1kHz 0.05 1kHz f 10kHz 0.3 10kHz f 100kHz 0.7 100kHz f 500kHz 1 33