FEATURES SY88802 5V 155Mbps LASER DIODE DRIVER WITH OUTPUT ENABLE Micrel SY88802 DESCRIPTION Up to 155Mbps operation Modulation current to 25mA PECL output enable Differential PECL inputs Single 5V power supply Available in a tiny 10-pin (3mm) MSOP The SY88802 is a high speed current switch for driving a semiconductor laser diode in optical transmission applications. The modulation current (IOUT) is controlled by the current (IRSET) through the external resistor RSET. The output OUT is HIGH and no current flows through OUT when output enable is HIGH. The device incorporates complementary open collector outputs with 25mA maximum current driving capability. The external resistor R EXT must be placed between /OUT and VCC to dissipate the worst case power. RSER is recommended to compensate for laser diode matching issues. The SY88802 utilizes the high performance bipolar ASSETTM technology. APPLICATIONS 155Mbps SONET FUNCTIONAL BLOCK DIAGRAM VCC REXT /OUT OUT RSER DIN /DIN to Laser Diode Internal IMOD Logic /EN 40X VCC GND VEE VREF RSET RSET ASSET is a trademark of Micrel, Inc. Rev.: A 1 Amendment: /0 Issue Date: March 2003 SY88802 Micrel PACKAGE/ORDERING INFORMATION Ordering Information Package Type Operating Range Package Marking SY88802KC K10-1 Commercial 802 SY88802KCTR* K10-1 Commercial 802 SY88802KI K10-1 Industrial 802 SY88802KITR* K10-1 Industrial 802 /EN 1 10 VCC Part Number DIN 2 9 OUT /DIN 3 8 /OUT VREF 4 7 GND RSET 5 6 GND *Tape and Reel 10-Pin MSOP (K10-1) PIN DESCRIPTION Pin Number Pin Name Pin Function 1 /EN 2, 3 DIN, /DIN 4 VREF Voltage reference for use with RSET. 5 RSET An external resistor connected from here to VREF sets the reference current for IOUT. 6, 7 GND Device ground. 9, 8 OUT, /OUT 10 VCC 100k PECL compatible input w/ 75k pulldown resistor. Modulation current goes to zero when deasserted high. Differential 100k PECL compatible input w/ 75k pulldown resistors. Differential open collector current outputs. Positive power supply. TRUTH TABLE(Note 1) D /D /EN OUT(Note 2) /OUT L H L H L H L L L H X X H H L Note 1. L = LOW, H = HIGH, X = don't care. Note 2. H = IOUT = 0mA. 2 SY88802 Micrel Absolute Maximum Ratings(Note 1) Operating Ratings(Notes 2, 3, 4) Power Supply Voltage (VCC) ............................ 0V to +7.0V Input Voltage (VIN) .............................................. 0V to VCC Output Current (IOUT) ................................................. 25mA Power Dissipation (PTOT) ........................................ 250mW Storage Temperature Range (TS) ............ -55C to +125C Supply Voltage (VCC) .................................. +4.5V to +5.5V Ambient Temperature (TA), Note 5 ............ -40C to +85C Junction Temperature (TJ), Note 5 ............ -40C to 100C Resistor to Dissipate Power (REXT) .................. 10 to 50 Laser Diode Serial Resistor (RSER) .................... 0 to 50 Resistor to Adjust Current (RSET) .......... 1500 to 50,000 Package Thermal Resistance MSOP (JA) Still-Air ...................................................... 113C/W (JB) Still-Air ........................................................ 74C/W Note 1. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to ABSOLUTE MAXIMUM RATlNG conditions for extended periods may affect device reliability. Note 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. Note 3. The device is guaranteed to meet the DC specifications, shown in the table above, after thermal equilibrium has been established. The device is tested in a socket such that transverse airflow of 500lfpm is maintained. Note 4. The voltage drop across REXT and RSER plus Laser Diode must not be greater than 2.3V. Note 5. Commercial devices are guaranteed from 0C to +85C ambient temperature. DC ELECTRICAL CHARACTERISTICS(Note 1) GND = 0V; VCC = 5V 10%; TA = -40C to +85C Symbol Parameter VIH Input HIGH Voltage (DIN, /DIN, /EN) VIL Input LOW Voltage (DIN, /DIN, /EN) VREF Reference Voltage IIL Input LOW Current (DIN, /DIN, /EN) IIH Input HIGH Current (DIN, /DIN, /EN) ICC Supply Current IOUT_OFF Output LOW Current (/EN = HIGH) IOUT Modulation Current 5 ARSET IOUT/IRSET 30 VOUT Voltage at OUT, /OUT COUT Capacitance on OUT, /OUT Note 1. Condition Min Typ Max Units VCC-1.165 VCC-0.880 V VCC-1.810 VCC-1.475 V 3.00 VIN = VIL(min) A 0.5 IMOD = 25mA 100 A 25 mA 500 A 15 25 mA 38 44 -- VCC V 16 VCC-2.3 2.5 Specification for packaged product only. 3 V pF SY88802 Micrel AC ELECTRICAL CHARACTERISTICS(Note 1, 2) GND = 0V; VCC = 5V 10%; TA = -40C to +85C Symbol Parameter Condition tPHL, tPLH D Propagation Delay DIN - OUT tPHL, tPLH EN Propagation Delay /EN - OUT tr, tf Rise/Fall Time (20% to 80%) IOR Output Current Ringing Min Max Units IOUT = 10mA 1000 ps IOUT = 10mA 1000 ps 1000 ps 10 % IOUT = 5 to 25mA Note 1. Specification for packaged product only. Note 2. REXT = RSER = 50 1%; RSER connected directly to VCC. TYPICAL OPERATING CHARACTERISTICS IMOD vs. RSET 30 25 IMOD (mA) 20 15 10 5 0.0 0.0 2.0K 4.0K 6.0K RSET ( 4 W) 8.0K 10K 12K Typ SY88802 Micrel 10 LEAD MSOP (K10-1) Rev. 00 MICREL, INC. TEL 1849 FORTUNE DRIVE SAN JOSE, CA 95131 + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB USA http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2003 Micrel, Incorporated. 5