MLX90224 Dual Hall Effect Switch Features and Benefits Chopper Stabilized Amplifier Stage CMOS for Optimum Stability, Quality and Cost Dual Output 5V to 24V Operation Phase/Direction Detection (option code B) Applications Direction Detector Speed Sensor Shaft Encoding Position Sensing Ordering Code Product Code MLX90224 Temperature Code E Package Code VA Option Code AAA-000 Packing Form Code BU Legend: Temperature Code: Package Code: Option Code: Packing Form: E for Temperature Range -40C to 85C VA for Plastic Single in Line xxx-000: Standard version BU for Bulk Ordering example: MLX90224EVA-AAA-000-BU 1. Functional Diagram 2. Description 1 Voltage Regulator Replaced with Logic for MLX90224 B 2 Chopper 4 Chopper 3 The MLX90224LVAA output transistor will be "switched on" (BOP) in the presence of a sufficiently strong South pole magnetic field facing the marked side of the package. Similarly, the output will be "switched off" (BRP) in the presence of a North field. Spacing on the plates is 1.85mm. The MLX90224LVAB serie is designed for direction detection with a high speed chopper. MLX90224EVA-A MLX90224EVA-B Pin 1 VDD VDD Pin 2 Switch Plate 1 Speed Pin 3 GND GND Pin 4 Switch Plate 2 Direction 3901090224 Rev. 007 The MLX90224 series are dual Hall effect switches. It includes two Hall effect switch functions of which typical thresholds are +/- 2.0 mT. In each switch, the magnetic flux detection is performed by a switched silicon Hall plate. The BOP and BRP are temperature-compensated and give a sensitivity temperature coefficient of 500 ppm/oC to compensate popular magnets. The output structure is an Open-Drain NMOS transistor with a capability of 25 mA. Page 1 of 10 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch TABLE OF CONTENTS FEATURES AND BENEFITS ....................................................................................................................... 1 APPLICATIONS............................................................................................................................................ 1 ORDERING INFORMATION......................................................................................................................... 1 1. FUNCTIONAL DIAGRAM................................................................................................................... 1-1 2. DESCRIPTION.................................................................................................................................... 2-1 3. GLOSSARY OF TERMS ....................................................................................................................... 3 4. ABSOLUTE MAXIMUM RATINGS ....................................................................................................... 3 5. MLX90224 ELECTRICAL SPECIFICATIONS ...................................................................................... 3 6. MLX90224 SENSOR SPECIFIC SPECIFICATIONS ............................................................................ 4 7. GENERAL DESCRIPTION .................................................................................................................... 4 8. PERFORMANCE GRAPHS................................................................................................................... 5 9. APPLICATIONS INFORMATION .......................................................................................................... 6 10. STANDARD INFORMATION REGARDING MANUFACTURABILITY OF MELEXIS PRODUCTS WITH DIFFERENT SOLDERING PROCESSES........................................................................................................................................ 8 11. ESD PRECAUTIONS............................................................................................................................. 8 12. PACKAGE INFORMATION................................................................................................................... 9 13. DISCLAIMER ....................................................................................................................................... 10 3901090224 Rev. 007 Page 2 of 10 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch 3. Glossary of Terms Gauss, Tesla: Two units to quantify a magnetic flux density. Conversion: 1 mT = 10 Gauss Bop: B Operating Point: When the magnetic flux density increases and reaches the Bop value, the output switches on. This value is in Gauss. Brp: B Release Point: When the magnetic flux density decreases and reaches the Brp value, the output switches off. This value is in Gauss. 4. Absolute Maximum Ratings Supply Voltage, VDD 24 V Supply Current, IDD 50 mA Output Current, IOUT 40 mA Output Short-Circuit Current 150 mA Operating Temperature Range, TA -40C to 150C Storage Temperature Range, TS -65C to 150C Maximum Junction Temp, TJ + 175C Magnetic Flux Density Infinite Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolutemaximum-rated conditions for extended periods may affect device reliability. 5. MLX90224 Electrical Specifications o o DC Operating Parameters TA = -40 C to 85 C, VDD = 5V to 24V (unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Supply Voltage VDD Supply Current IDD Output Current IOUT B>BOP Saturation Output Voltage VSAT B>BOP, IOUT=20 mA Output Voltage VOUT B<BRP Output Leakage ILEAK Refresh Time 3901090224 Rev. 007 Operating 5 3.0 Tr 200 7 Page 3 of 10 7.5 Units 24 V 10 mA 20 mA 600 mV 24 V 10 A 15 S Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch 6. MLX90224 Sensor Specific Specifications DC Operating Parameters TA = -40oC to 85oC, VDD = 5V to 24V (unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Units Operate Point BOP - 2.5 5.5 mT Release Point BRP -5.5 -2.5 - mT Hysteresis BHYS 1.0 4.0 7.5 mT Note: 1 mT = 10 Gauss 7. General Description The MLX 90224 is designed for use with multipole ring magnet targets having evenly distributed North and South magnetic poles on the circumference of the target. An example of the basic physical arrangement of the sensor and magnet is shown in Fig. 1. The MLX90224 is available in 2 versions. The first version provides the user with two digital output signals. Output S1 will provide a speed pulse from the changing magnetic flux at sensing element S1. Output S2 will provide a phase shifted (d = 1.85 mm) output identical in pulse width and period to S1. This version is referred to as MLX90224LVAA. The MLX90224LVAB version provides an output signal that decodes the phase shifted signals to directly provide an output for the speed which is twice the rotation speed of the target. The other output pin represent the direction and changes from logic-high to logic-low when the direction of rotation of the magnet is reversed. It allows to directly see the condition of the speed with twice the resolution of the MLX90224LVAA and to also know directly the direction of rotation of the target. The MLX90224LVAA has switching magnetic Bop and Brp values of typically +/- 2.5 mT as does the internal circuitry of the LVAB. Figure 1: Application with a multipole ring magnet 3901090224 Rev. 007 Page 4 of 10 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch 8. Performance Graphs Output Voltage versus Flux Density Typical Magnetic Switch Points versus Temperature 90224 A, B 5 90224 A, B 25 VDD 20 3 Output Voltage (V) Flux Density (mT) BOP 1 0 -1 BRP 15 BRP BOP 10 5 -3 Vsat -5 -40 0 0 40 80 120 160 -6 200 -4 90224 2 4 6 90224 500 8 400 TA = -40oC VDS(ON) (mV) Supply Current (mA) 0 Typical Saturation Voltage versus Temperature VDD = 12 V, IOUT = 20mA Typical Supply Current versus Supply Voltage 10 -2 Flux Density (mT) Temperature (oC) 6 TA = 25 oC TA = 85 C 4 2 300 VDS(ON) 200 100 0 0 5 10 15 20 25 0 -40 30 Supply Voltage (V) 3901090224 Rev. 007 0 40 80 120 160 200 Temperature (oC) Page 5 of 10 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch 9. Applications Information Severe Environment and Automotive Protection Circuit V DD R1 R2 MLX 90224 R3 Output Output C1 C2 C2 R1, R2 = 5.6k R3 = 332 C1 = 10nF C2 = 2.2nF In severe cases it may be necessary to include a Zener diode to clamp positive interference and Schottky diodes to clamp negative excursions. 3901090224 Rev. 007 Page 6 of 10 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch Timing diagram when applied a B1-B2 quadratic magnetic field on MLX90224, LVAA version 60 Magnetic Field (G) 40 Bop 20 B1 B2 0 -20 Brp -40 Out 1 Out 2 0 20 40 60 80 100 120 140 160 180 200 time (ms) Timing diagram when applied a B1-B2 quadratic magnetic field on MLX90224, LVAB version (direction and speed outputs) 50 Magnetic Field (G) Bop B1 B2 0 Brp -50 Signal from Plate 1 Signal from Plate 2 Speed output Direction output 0 3901090224 Rev. 007 50 100 150 200 time Page 7 of 10 250 300 350 400 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch 10. Standard information regarding manufacturability of Melexis products with different soldering processes Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity level according to following test methods: Reflow Soldering SMD's (Surface Mount Devices) * * IPC/JEDEC J-STD-020 Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices (classification reflow profiles according to table 5-2) EIA/JEDEC JESD22-A113 Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing (reflow profiles according to table 2) Wave Soldering SMD's (Surface Mount Devices) and THD's (Through Hole Devices) * * EN60749-20 Resistance of plastic- encapsulated SMD's to combined effect of moisture and soldering heat EIA/JEDEC JESD22-B106 and EN60749-15 Resistance to soldering temperature for through-hole mounted devices Iron Soldering THD's (Through Hole Devices) * EN60749-15 Resistance to soldering temperature for through-hole mounted devices Solderability SMD's (Surface Mount Devices) and THD's (Through Hole Devices) * EIA/JEDEC JESD22-B102 and EN60749-21 Solderability For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature, temperature gradient, temperature profile etc) additional classification and qualification tests have to be agreed upon with Melexis. The application of Wave Soldering for SMD's is allowed only after consulting Melexis regarding assurance of adhesive strength between device and board. Melexis is contributing to global environmental conservation by promoting lead free solutions. For more information on qualifications of RoHS compliant products (RoHS = European directive on the Restriction Of the use of certain Hazardous Substances) please visit the quality page on our website: http://www.melexis.com/quality.aspx 11. ESD Precautions Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. 3901090224 Rev. 007 Page 8 of 10 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch 12. Package Information VA Package Dimensions 5.33 5.43 5.08 5.24 VA Hall Plate / Chip Location 3.615 2.69 1.765 J Hall Plates 0.25 x 0.25 1.22 1.32 3.76 3.86 4.50 2.700 1.700 A 4.10 0.387 0.289 B 45 o X 1mm C 224XA ZZZZZ 5o 5o (2x) (2x) 2.180 3. 46 3. 30 0.387 0.289 Marked Surface 3 .79 3 .63 D VA F All Dimensions in millimeters G H 1.0 0.22 REF B MAX 1 2 3 A 4 C 1.20 1.10 0.66 0.61 0.29 0.24 15.50 14.50 D E 45 o 0.31 0.18 F 0.45 0.35 G 0.60 0.40 0.35 0.25 H J E 0.15 0.0 45 o Notes: 1. Pinout: Pin 1 Vdd Pin 2 Latch Plate 1/ Speed Pin 3 GND Pin 4 Latch Plate 2 / Direction 2. Controlling dimension: mm . 3. Leads must be free of flash and plating voids. 4. Leads must not arc toward the rear of package. 5. Package dimensions exclude molding flash. 6. Tolerance: +/- 0.254 mm unless otherwise specified. 7. Marking: Line 1: 3 first digits (224) =Part Number MLX90224 4th and 5th digits (XA) = Version A (double latch) (XB) = Version B (Speed-Direction) Line 2: 5 digits (ZZZZZ) =Lot Number Back Side Marking 4 digits (WWYY) =Date Code 3901090224 Rev. 007 Page 9 of 10 Data Sheet Apr/12 MLX90224 Dual Hall Effect Switch 13. Disclaimer Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis' rendering of technical or other services. (c) 2012 Melexis NV. All rights reserved. For the latest version of this document, go to our website at www.melexis.com Or for additional information contact Melexis Direct: Europe, Africa, Asia: Phone: +32 1367 0495 E-mail: sales_europe@melexis.com America: Phone: +1 248 306 5400 E-mail: sales_usa@melexis.com ISO/TS 16949 and ISO14001 Certified 3901090224 Rev. 007 Page 10 of 10 Data Sheet Apr/12