WXP-104K - World Products Inc.

THIS PAGE WAS INTENTIONALLY LEFT BLANK.

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

RFI Supprssors | 1

World Products’ Metallized Polypropylene and Polyester RFI Suppressors are intended for use on line-to-line (X2) and line-to-ground

(Y2) AC Mains. Our proprietary construction method allows these devices to withstand the stresses of high voltage transient pulses

and remain safe according to international safety standards without degradation of performance. They are constructed of the nest

materials available for the purpose of providing maximum reliability and long life. Stringent quality controls are used throughout

production.

These suppressors are designed to suppress radio interference, conducted on the AC mains, generated from household appliances,

computers, switch mode power supplies, and other electronic equipment. They are available in a wide range of capacitance values

and industry standard case sizes.

Featuring...

• International Safety Approvals

• Excellent Self Healing Properties

• High Dv/Dt Ratings

• Flame Retardant Encapsulation

• 100% Production Lot Testing

• Standard Electrical AQL - 0.065

• RoHS Compliance commenced July 2005

General Information

RFI suppressors are a special class of capacitors for use on the AC power line inputs to electronic or electrical equipment. Their

purpose is to eliminate or attenuate radio frequency interference voltages originated in the units connected to the same AC power

branch and prevent them from mutually disturbing their operations.

They must endure very harsh conditions existing on the 60/50Hz AC power lines — including voltage surges and transients.

Therefore, they must meet the requirements of EN 60384-14 and IEC 384-14, 2nd edition 1993 standards enforced by international

safety certication bodies, as well as UL-1414 and UL-1283 in USA.

Our RFI capacitors are made with metallized polypropylene or polyester lms of the highest quality and have self healing properties.

There are two classes of these capacitors: Line-to-Line X2 Class, and Line-to-Ground Y2 Class. We have two series of X2 — WXP

and WXPC series rated at 300VAC and 275VAC(2.2-6.8μF rated at 300VAC (600VDC).) — and two series of Y2 — WYP and WYE

rated at 275VAC and 250 VAC. WXP, WXPC (smaller dimensions) and WYP series are made with polypropylene lm. WYE series is

made with polyester lm.

While polypropylene and polyester series are compatible, polypropylene dielectrics are more popular worldwide and have smaller

dissipation factor (DF) improving operation at higher frequencies. Also, due to larger production volumes polypropylene capacitors

are less expensive.

Our manufacturing plant has received the Certicate of Quality Assurance System according to the ISO9001 standard.

Please contact World Products, LLC for more information about RFI suppressors.

Table of Contents

General Information ........................................................................... 1

RoHS Compliance ............................................................................ 2

Denition of Terms ............................................................................ 2

Mechanical Specications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Marking and Safety Approvals .................................................................. 3

WXP & WXPC Series .......................................................................... 4

WYP Series ................................................................................. 8

WYE Series ................................................................................. 10

Taping Specications ......................................................................... 12

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

2 | RFI Suppressors

RoHS Compliance

WXPC 0.010 to 1.5μF/275VAC class X2 This is to certify that the referenced RFI suppressors purchased

from World Products, LLC comply to a maximum concentration

value of 0.1% by weight in homogeneous materials for lead (Pb),

mercury, hexavalent chromium, polybrominated biphenyls (PBB)

and polybrominated diphenyl ethers (PBDE) and of 0.01% weight

in homogeneous materials for cadmium and are in compliance with

Directive 2002/95/EC of the European Parliament and of the Council

of 27 January 2003 on the restriction of the use of certain hazardous

substances in electrical and electronic equipment (RoHS Directive)

as of July 2005 (date code marking starting 0527). Additionally “R”

marking (per marking specication) is initiated starting with date

code 0544 to further identify RoHS compliant products.

WXPC 2.2 to 6.8μF/300VAC class X2

WXP 0.010 to 2.2μF/300VAC class X2

WYP 0.010 to 0.1μF/275VAC class Y2

WYE 0.001 to 0.0068μF/250VAC class Y2

Note

All our capacitors listed above have Climatic Category: IEC 40/100/56 C,and Operating Temperature Range: -40 to +100°C.

Deﬁnition of Terms

Capacitance

Capacitance values are measured and specied for 1KHz at 25°C

Dissipation Factor (DF)

The measure of the suppressor’s dielectric loss at 1KHz also called tangent of loss angle. It is the ratio of loss power to the reactive power across

capacitor that is customarily expressed in % (Ratio = tanF = .01 —> DF = 1%). At large DF and operation above specied limits loss power may cause

signicant internal heating leading to destructive breakdown. All of our suppressors are designed and made with top quality materials to minimize DF.

Insulation Resistance (IR)

Measurement of the specied IR is made after applying 100 VDC for one minute at 25°C. The proprietary multiple dielectric design of our suppressors

provides higher insulation resistance than single dielectric suppressors.

Climatic Category

According to international safety standards, IEC 60384-14, and IEC 60068-2, suppressors must be categorized according to the rated lowest

temperature / the rated highest temperature / the number of days samples are subjected to damp humidity test — in our case: 56 days — which is the

absolute maximum rating category.

Rated Voltage

The rated voltage is the maximum RMS AC voltage which can be applied continuously within the specied Rated Temperature range.

Rated Temperature Range

The maximum low and high ambient temperature at which the rated voltage can be continuously applied.

Endurance Life Test

Production samples are subjected to a periodic life endurance testing to comply with international safety approval standards. These tests specify

that the suppressor shall have 1.25 x rated voltage (X2) and 1.7 x rated voltage (Y2) applied for a period of 1,008 hours at an elevated temperature

of 100°C. We test our WYE suppressors with the above endurance voltages, not only at the time of type approval, but also at 6 month intervals. In

addition to the above voltages applied constantly, 1000 VAC is applied once each hour for 0.1 second. Both the steady state and momentary (0.1

sec) 1000 VAC voltage is applied through a 47 ohm ± 5% resistor simulating the high frequency impedance of AC mains. After the endurance life test,

capacitance shall not deviate more than 5% of the initial value, IR shall not be less than 50% of the initial value and DF shall not be greater than the

specied. The combined stress of both voltages applied is proof that these suppressors are capable of withstanding high line conditions that are often

present on the AC mains.

dv/dt

The maximum acceptable voltage rate of change per μsec of rise or fall time as dened below:

dv/dt =

VR = Rated DC Voltage

R = Discharge Resistor

C = Capacitance Tested

————

R x C

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

RFI Supprssors | 3

Mechanical Speciﬁcations

Vibration IEC 68 - 2 - 6, test FC 3 directions at 2 hours each

10-500 Hz at 98 m/s2

Bump IEC 68 - 2 - 29, test Eb 4000 Bumps at 390 m/s2

Solderability IEC 60068-2-20 (Method 2)

Fire Hazard UL1414

IEC 695 - 2 - 2

According to Section 18 in this Standard

P > = 15mm, 120 seconds

P < = 15mm, 60 seconds.

Humidity IEC 68 - 2 - 3, test Ca X Class 56 days.

Y Class 56 days.

Plastic Case UL 94V - 0 Flame Retardant, Molded Plastic,

Epoxy Resin Sealed.

Operating

Temperature -40ºC to +100ºC

Storage

Temperature +5ºC to +35ºC RH ≤ 80% (area should be free from bases, acids, salts,

mold & fungi).

Marking and Safety Approvals

Marking

• World Products, LLC Logo

• Part Number & Film Symbol (MKP or MKT)

• Capacitance

• Rated Voltage

• Climatic Category

• Class (X2 or Y2)

• Safety Approval Marking

• EIA Date Code (YYWW) Year & Week #

• “R” (optional) for RoHS Compliant type

Safety Approval References

Symbol Country Reference WYE File WXP File WXPC File WYP File

UL USA UL 1283 E119899 E119899 E119899 E119899

UL and C-UL USA **UL 1414 E71602 E71602 E71602 E71602

CSA Canada **22.2 No.1 LR86091

CSA Canada E384-14-95 ***LR86091

VDE Germany * 87425 94633 94633 132747

* Approval test standards: EN 60384-14, 1994/IEC 384-14, 2nd Edition, 1993

** UL1414, C-UL, and CSA 22.2 No. 1 approvals apply only up to 1μF.

*** For WXP capacitance values 1.5uF and 2.2uF only.

NOTE: Approvals only apply to solid uninsulated leads (standard lead type) with the exception of UL1414/C-UL where approvals additionally extend to

stranded cu wire, 0.5mm 2, PCV insulated with 7.0 striped end.

WXPC-335K R

3.3µF K MKP

40/100/56/C

300V~

0544

Year Week

EN 60384-14

1283

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

4 | RFI Suppressors

WXP & WXPC Series

Part Numbering System

Metallized Polypropylene Film Capacitors

Example:

WXP - 103 K L04 02 (51)

(1) (2) (3) (4) (5) (6)

(1) Metallized Polypropylene Film Suppressors(X2)

WXP = WXP Series

WXPC = WXPC Series

(2) Capacitance

Example: 103 = 0.010μF

WXP Series available in 0.01-2.2μF

WXPC Series available in 0.01-6.8μF

(3) Tolerance

K = ±10%

M = ±20%

J = ±5% (Only available for WXPC 2.2 - 6.8µF)

(4) Lead Lengths

Nil = 30mm min

L04 = 4 ± 1mm

L05 = 5 ± 1mm

L06 = 6 ± 1mm

(5) Lead Type

Nil = Solid uninsultated wire ø = 0.8mm diameter

02 = Solid cu wire, 0.8mm diameter, PCV insulated*

03 = Stranded cu wire, 0.5mm2 PCV insulated*

(6) Custom Lead Length sufﬁx

Example: (45) = 45mm lead length**

* All insulated leads have 7.0mm striped and tinned ends. These options are only available for types with 15mm or larger lead spacing (P).

** If longer lead length other than standard 30mm min is required that lead length is noted after the appropriate sufx 02 or 03 for insulated leads (i.e.:

for 45mm lead length 02(45), 03(45) or in the case of uninsulated leads (45).)

30 mm

min.

Center to Center

7 ± 2mm

See Lead

Notes

Insulated Leads Versions

Only WX

P and WXPC

Uninsulated Leads Versions

30 mm

min.

Center to Center

See Lead

Notes

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

RFI Supprssors | 5

WXP & WXPC Series (continued)

WXP Dimensions

Part

Number

± 0.3 mm

Quantity Per Box

Long Lead 30-35mm Short Lead 4, 5, 6mm

WXP-103K 18.0 10.5 5.5 15.0±0.5 500 1300

WXP-153K 18.0 10.5 5.5 15.0±0.5 500 1300

WXP-223K 18.0 10.5 5.5 15.0±0.5 500 1300

WXP-333K 18.0 10.5 5.5 15.0±0.5 500 1300

WXP-473K 18.0 12.5 6.5 15.0±0.5 400 950

WXP-683K 18.0 13.5 7.5 15.0±0.5 400 750

WXP-104K 18.0 14.5 8.5 15.0±0.5 400 624

WXP-154K 26.5 15.5 7.5 22.5±0.5 200 498

WXP-224K 26.5 16.5 8.5 22.5±0.5 200 438

WXP-334K 26.5 18.5 10.5 22.5±0.5 150 330

WXP-474K 31.5 20.5 11.5 27.5±0.7 100 220

WXP-684K 31.5 23.5 13.5 27.5±0.7 100 150

WXP-105K 31.5 24.5 15.0 27.5±0.7 80 140

WXP-155K 41.5 28.5 16.0 37.5±0.7 40 80

WXP-225K 41.5 33.0 18.0 37.5±0.7 40 80

WXPC Dimensions

Part

Number

± 0.3 mm

Quantity Per Box

Long Lead 30-35mm Short Lead 4, 5, 6mm

WXPC-103K 13.0 10.5 4.5 10.0±0.5 1000 2200

WXPC-153K 13.0 10.5 4.5 10.0±0.5 1000 2200

WXPC-223K 13.0 10.5 5.5 10.0±0.5 1000 1800

WXPC-333K 13.0 12.5 5.5 10.0±0.5 800 1500

WXPC-473K1 18.0 10.5 5.5 15.0±0.5 500 1300

WXPC-683M 18.0 10.5 5.5 15.0±0.5 500 1300

WXPC-104K 18.0 12.5 6.5 15.0±0.5 500 950

WXPC-154K 18.0 14.5 8.5 15.0±0.5 400 650

WXPC-224K 18.0 17.0 8.5 15.0±0.5 300 550

WXPC-224K1 26.5 15.5 7.5 22.5±0.7 200 498

WXPC-274K 26.5 15.5 7.5 22.5±0.7 200 498

WXPC-334K 26.5 16.5 8.5 22.5±0.7 200 438

WXPC-474K 26.5 18.5 10.5 22.5±0.7 150 330

WXPC-684K 31.5 20.5 11.5 27.5±0.7 100 220

WXPC-105K 31.5 23.5 13.5 27.5±0.7 100 150

WXPC-155M 31.5 24.5 15.0 27.5±0.7 80 140

L ± 0.5 mm H ± 0.5 mm W ± 0.5 mm

WXPC-225K 41.5 28.5 16.0 37.5±0.7 40 80

WXPC-335K 41.5 33.0 18.0 37.5±0.7 40 80

WXPC-475K 42.0 38.0 21.0 37.5±0.7 40 45

WXPC-685M 42.0 38.0 21.0 37.5±0.7 40 45

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

6 | RFI Suppressors

WXP & WXPC Series (continued)

WXP Speciﬁcations

Part

Number

Tolerance dv/dt Dissipation Factor

(DF)

Insulation

Resistance (IR)

Test Voltage

for 1 second

Rated Voltage

50/60Hz to

440Hz

Typical

Resonant

Frequencies

μF % v/μs % Note 4 VDC VAC fo - MHz

WXP-103K 0.010 ±10 500 <0.10% at 10kHz >30000MΩ 2150 300 13.0

WXP-153K 0.015 ±10 500 <0.10% at 10kHz >30000MΩ 2150 300 10.4

WXP-223K 0.022 ±10 500 <0.10% at 10kHz >30000MΩ 2150 300 8.5

WXP-333K 0.033 ±10 500 <0.10% at 10kHz >30000MΩ 2150 300 6.9

WXP-473K 0.047 ±10 500 <0.10% at 10kHz >30000MΩ 2150 300 6.0

WXP-683K 0.068 ±10 500 <0.10% at 10kHz >30000MΩ 2150 300 4.7

WXP-104K 0.100 ±10 500 <0.10% at 10kHz >30000MΩ 2150 300 4.0

WXP-154K 0.150 ±10 300 <0.50% at 10kHz >30000MΩ 2150 300 3.4

WXP-224K 0.220 ±10 300 <0.50% at 10kHz >30000MΩ 2150 300 2.7

WXP-334K 0.330 ±10 300 <0.50% at 10kHz >30000MΩ 2150 300 2.3

WXP-474K 0.470 ±10 300 <0.50% at 10kHz >10000ΩF 2150 300 1.9

WXP-684K 0.680 ±10 300 <0.50% at 10kHz >10000ΩF 2150 300 1.6

WXP-105K 1.00 ±10 200 <0.50% at 10kHz >10000ΩF 2150 300 1.3

WXP-155K 1.50 ±10 200 <0.10% at 1kHz >10000ΩF 2150 300 1.0

WXP-225K 2.20 ±10 200 <0.10% at 1kHz >10000ΩF 2150 300 0.85

1. All measurements are based on 5mm lead lengths at nominal C values.

2. Actual resonant frequencies will depend also on the total length of the circuit connections to the capacitor terminals and capacitor’s actual C value.

3. Our factory tests each production lot for 100% to the test voltages listed above. After the test voltage has been applied, 100% of all production is

tested for DF, IR and capacitance to insure all suppressors comply with electrical specications.

4. Insulation Resistance (IR) is measured at 100VDC after 60 seconds at +25°C.

5. These specications are for both ±10% and ±20% tolerance parts.

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

RFI Supprssors | 7

WXP & WXPC Series (continued)

WXPC Speciﬁcations

Part

Number

Tolerance dv/dt Dissipation Factor

(DF)

Insulation

Resistance(IR)

Test Voltage

for 1 second

Rated Voltage

50/60Hz to

440Hz

Typical

Resonant

Frequencies

μF % v/μs % Note 4 VDC VAC fo - MHz

WXPC-473K1 0.047 ±10 500 <0.10% at 10kHz >30000MΩ 2150 275 6.0

WXPC-683M 0.068 ±20 500 <0.10% at 10kHz >30000MΩ 2150 275 4.7

WXPC-104K 0.100 ±10 500 <0.10% at 10kHz >30000MΩ 2150 275 4.0

WXPC-154K 0.150 ±10 300 <0.50% at 10kHz >30000MΩ 2150 275 3.4

WXPC-224K 0.22 ±10 300 <0.50% at 10kHz >30000MΩ 2150 275 2.7

WXPC-224K1 0.22 ±10 300 <0.50% at 10kHz >30000MΩ 2150 275 2.7

WXPC-274K 0.27 ±10 300 <0.50% at 10kHz >30000MΩ 2150 275 2.5

WXPC-334K 0.33 ±10 300 <0.50% at 10kHz >30000MΩ 2150 275 2.3

WXPC-474K 0.47 ±10 300 <0.50% at 10kHz >10000ΩF 2150 275 1.9

WXPC-684K 0.68 ±10 300 <0.50% at 10kHz >10000ΩF 2150 275 1.6

WXPC-105K 1.0 ±10 200 <0.50% at 10kHz >10000ΩF 2150 275 1.3

WXPC-155M 1.5 ±20 200 <0.10% at 1kHz >10000ΩF 2150 275 1.0

WXPC-225K 2.2 ±10 100 <0.10% at 1kHz >10000ΩF 2150 300 0.85

WXPC-335K 3.3 ±10 100 <0.10% at 1kHz >10000ΩF 2150 300 -

WXPC-475K 4.7 ±10 100 <0.10% at 1kHz >10000ΩF 2150 300 -

WXPC-685M 6.8 ±20 100 <0.10% at 1kHz >10000ΩF 2150 300 -

1. All measurements are based on 5mm lead lengths at nominal C values.

2. Actual resonant frequencies will depend also on the total length of the circuit connections to the capacitor terminals and capacitor’s actual C value.

3. Our factory tests each production lot for 100% to the test voltages listed above. After the test voltage has been applied, 100% of all production is

tested for DF, IR and capacitance to insure all suppressors comply with electrical specications.

4. Insulation Resistance (IR) is measured at 100VDC after 60 seconds at +25°C.

5. These specications are for 0.01 - 1.5µF for ±10% and ±20% tolerance and 2.2 - 6.8µF for ±5%, ±10%, and ±20% tolerance parts.

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

8 | RFI Suppressors

WYP Series

Part Numbering System

Metallized Polypropylene Film Capacitors

Example:

WYP - 103 M L04 (51)

(1) (2) (3) (4) (5)

(1) Metallized Polypropylene Film Suppressors(Y2)

WYP = WYP Series

(2) Capacitance

Example: 103 = 0.010μF

WYP Series available in 0.01-0.1μF

(3) Tolerance

M = ±20%

(4) Lead Lengths

Nil = 30mm min, Solid uninsultated wire ø = 0.8mm diameter

L04 = 4 ± 1mm, Solid uninsultated wire ø = 0.8mm diameter

L05 = 5 ± 1mm, Solid uninsultated wire ø = 0.8mm diameter

L06 = 6 ± 1mm, Solid uninsultated wire ø = 0.8mm diameter

(5) Custom Lead Length sufﬁx

Example: (45) = 45mm lead length*

* If longer lead length other than standard 30mm min is required that lead length is noted after the part number (i.e.: for 45mm lead length (45).)

30 mm

min.

Center to Center

7 ± 2mm

See Lead

Notes

Insulated Leads Versions

Only WXP and WXPC

Uninsulated Leads Versions

30 mm

min.

Center to Center

See Lead

Notes

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

RFI Supprssors | 9

WYP Series (continued)

WYP Dimensions

Part

Number

±0.3 mm

±0.5 mm

Quantity Per Box

Long Lead 30-35mm Short Lead 4, 5, 6mm

WYP-103M 18.0 10.5 5.5 15.0 500 1300

WYP-153M 18.0 12.5 6.5 15.0 400 950

WYP-223M 18.0 13.5 7.5 15.0 400 750

WYP-273M 18.0 14.5 8.5 15.0 400 650

WYP-333M 18.0 17.0 8.5 15.0 300 550

WYP-473M 26.5 15.5 7.5 22.0 200 480

WYP-683M 26.5 16.5 8.5 22.0 200 400

WYP-104M 26.5 18.5 10.5 22.5 150 330

WYP Speciﬁcations

Part

Number

Tolerance dv/dt Dissipation

Factor (DF)

Insulation

Resistance

(IR)

Test Voltage

for 2 seconds

Rated Voltage

50/60Hz to

440Hz

Typical

Resonant

Frequencies

μF % v/μs % at 10kHz MΩ VDC VAC fo - MHz

WYP-103M 0.010 ±20 700 <0.08 >30000 2700 275 15

WYP-153M 0.015 ±20 700 <0.08 >30000 2700 275 12

WYP-223M 0.022 ±20 700 <0.08 >30000 2700 275 10

WYP-273M 0.027 ±20 700 <0.08 >30000 2700 275 8.1

WYP-333M 0.033 ±20 700 <0.08 >30000 2700 275 6.9

WYP-473M 0.047 ±20 500 <0.08 >30000 2700 275 5.5

WYP-683M 0.068 ±20 500 <0.08 >30000 2700 275 4.7

WYP-104M 0.100 ±20 500 <0.08 >30000 2700 275 4.0

1. All measurements are based on 5mm lead lengths at nominal C values.

2. Actual resonant frequencies will depend also on the total length of the circuit connections to the capacitor terminals and capacitor’s actual C value.

3. Our factory tests each production lot for 100% to the test voltages listed above. After the test voltage has been applied, 100% of all production is

tested for DF, IR and capacitance to insure all suppressors comply with electrical specications.

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

10 | RFI Suppressors

Uninsulated Leads

30 mm

min.

Center to Center

See Lead

Notes

WYE Series

Part Numbering System

Metallized Polyester Film Capacitors

Example:

WYE - 102 M L04 (51)

(1) (2) (3) (4) (5)

(1) Metallized Polyester Film Capacitors(Y2)

WYE = WYE Series

(2) Capacitance

Example: 103 = 0.010μF

WYE Series available in 0.001-0.0068μF

(3) Tolerance

M = ±20%

(4) Lead Lengths

Nil = 30mm min, Solid uninsultated wire ø = 0.8mm diameter

L04 = 4 ± 1mm, Solid uninsultated wire ø = 0.8mm diameter

L05 = 5 ± 1mm, Solid uninsultated wire ø = 0.8mm diameter

L06 = 6 ± 1mm, Solid uninsultated wire ø = 0.8mm diameter

(5) Custom Lead Length sufﬁx

Example: (45) = 45mm lead length*

* If longer lead length other than standard 30mm min is required that lead length is noted after the part number (i.e.: for 45mm lead length (45).)

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

RFI Supprssors | 11

WYE Series (continued)

WYE Dimensions

Part

Number

max

±0.5 mm

Quantity Per Box

Long Lead

30-35mm

Short Lead

4, 5, 6mm

WYE-102M 13.0 10.5 4.5 10.0 1000 2200

WYE-152M 13.0 10.5 4.5 10.0 1000 2200

WYE-222M 13.0 10.5 5.8 10.0 1000 1800

WYE-252M 13.0 10.5 5.8 10.0 1000 1800

WYE-332M 13.0 12.5 5.8 10.0 800 1500

WYE-392M 13.0 12.5 5.8 10.0 800 1500

WYE-472M 13.0 13.5 5.8 10.0 800 1400

WYE-682M 18.0 14.0 5.8 15.0 500 1000

WYE Speciﬁcations

Part

Number

Capacitance Tolerance dv/dt

Dissipation

Factor (DF)

Insulation

Resistance

(IR)

Test Voltage

for 2 seconds

Rated Voltage

50/60Hz

Typical

Resonant

Frequencies

μF % v/μs % at 1KHz MΩ VDC VAC fo - MHz

WYE-102M 0.0010 ±20 1000 <0.8 >30000 3000 250 53

WYE-152M 0.0015 ±20 1000 <0.8 >30000 3000 250 42

WYE-222M 0.0022 ±20 1000 <0.8 >30000 3000 250 35

WYE-252M 0.0025 ±20 1000 <0.8 >30000 3000 250 33

WYE-332M 0.0033 ±20 1000 <0.8 >30000 3000 250 29

WYE-392M 0.0039 ±20 1000 <0.8 >30000 3000 250 25

WYE-472M 0.0047 ±20 1000 <0.8 >30000 3000 250 21

WYE-682M 0.0068 ±20 600 <0.8 >30000 2700 250 19

1. All measurements are based on 5mm lead lengths at nominal C values.

2. Actual resonant frequencies will depend also on the total length of the circuit connections to the capacitor terminals and capacitor’s actual C value.

3. Our factory tests each production lot for 100% to the test voltages listed above. After the test voltage has been applied, 100% of all production is

tested for DF, IR and capacitance to insure all suppressors comply with electrical specications.

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

12 | RFI Suppressors

Taping Speciﬁcations

Taping of Capacitors

The original lead spacing of 10.0 mm (sufﬁx code — T1)

(the pitch of holes on carrier tape = 12.7 mm) (All dimensions in mm)

The original lead spacing of 15.0 mm (sufﬁx code — T2)

(the pitch of holes on carrier tape = 12.7 mm) (All dimensions in mm)

±0.5

18.0

±0.1

12.0

±0.4

12.7

(25.4)

±0.2

4.0

(7.7)

±0.2

12.7

max 1.3 max 1.3

0.5

9.0 ±

max 11

±0.5

18.5

max 33

max 2 max 2

0.5 +1.5

- 0.0

10.0+0.5

- 0.1

direction of unreeling

detail A

max 0.9

max 1.5

min 0.35

±0.5

18.0

±0.1

12.0

±0.4

12.7

(25.4)

±0.2

4.0

(5.2)

±0.2

12.7

max 1.3 max 1.3

±0.5

9.0

max 11

±0.5

18.5

max 35

15.0+0.5

- 0.1

0.5 +1.5

- 0.0

max 2 max 2

max 0.9

max 1.5

min 0.35

direction of unreeling

detail A

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

RFI Supprssors | 13

Taping Speciﬁcations (continued)

Taping of Capacitors

The original lead spacing of 10.0 mm crimped to the lead spacing of 7.5 mm (sufﬁx code — T3)

(the pitch of holes on carrier tape = 15.0 mm) (All dimensions in mm)

The original lead spacing of 15.0 mm crimped to the lead spacing of 7.5 mm (sufﬁx code — T4)

(the pitch of holes on carrier tape = 15.0 mm) (All dimensions in mm)

±0.5

18.0

±0.1

12.0

(15)

±0.2

4.0

(3.75)

±0.2

15.0

max 1.3 max 1.3

±0.5

9.0

max 11

max 38

0.5 +1.5

- 0.0

±0.4

7.5

10.0

15.5

F = 7.5 +0.6

- 0.1

(F - F1) < 0.3

16.0 (*)

+2.0

- 0.0

(*) The distance between reference plane and hole symmetry axis.

max 2 max 2

max 0.9

max 1.5

max 2 max 2

max 0 9

max 1 5

min 0.35

direction of unreeling detail A

±0.5

18.0

±0.1

12.0

(30)

±0.2

4.0

(3.75)

±0.2

15.0

max 1.3 max 1.3

±0.5

9.0

max 11

max 38

0.5 +1.5

- 0.0

±0.4

7.5

10.0

15.5

16.0 (*)

+2.0

- 0.0

max 2 max 2

max 0.9

max 1.5

min 0.35

detail A

F = 7.5 +0.6

- 0.1

(F - F1) < 0.3

(*) The distance between reference plane and hole symmetry axis.

direction of unreeling

RFI SuppReSSoRS

World Products, LLC 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com Rev. 4.9 (05.06.10)

14 | RFI Suppressors

Taping Speciﬁcations (continued)

Packaging of Capacitors

AMMO Packing

Capacitor case dimension

(W x H x L)

Lead

spacing

Number of taped

capacitors per box

mm mm pcs

4.5 x 10.5 x 13.0 10.0 516

5.5 x 10.5 x 13.0 10.0 420

5.5 x 12.5 x 13.0 10.0 420

5.5 x 13.5 x 13.0 10.0 420

5.5 x 10.5 x 18.0 15.0 420

5.5 x 14.0 x 18.0 15.0 420

6.5 x 12.5 x 18.0 15.0 360

7.5 x 13.5 x 18.0 15.0 312

8.5 x 14.5 x 18.0 15.0 276

8.5 x 17.0 x 18.0 15.0 276*

4.5 x 10.5 x 13.0 10.0 / 7.5 860

5.5 x 10.5 x 13.0 10.0 / 7.5 700

5.5 x 12.5 x 13.0 10.0 / 7.5 700

5.5 x 13.5 x 13.0 10.0 / 7.5 700

5.5 x 10.5 x 18.0 15.0 / 7.5 350

5.5 x 14.0 x 18.0 15.0 / 7.5 350

6.5 x 12.5 x 18.0 15.0 / 7.5 300

7.5 x 13.5 x 18.0 15.0 / 7.5 260

8.5 x 14.5 x 18.0 15.0 / 7.5 230

8.5 x 17.0 x 18.0 15.0 / 7.5 230*

Requirements

1. A maximum of 2 consecutive capacitors may be missing provided this gap is followed by 6 consecutive capacitors.

2. The maximum number of empty places per reel shall not exceed 0.5% of the total number of the capacitors per reel.

3. Cummulative pitch error over 20 pitches: ± 1.0 mm.

4. The other taping requirements: acc. to EN/IEC 60286-2 & EIA-468-B.

*52mm for .22uF.

3 43

7*4

237

Unit: mm

THIS PAGE WAS INTENTIONALLY LEFT BLANK.