T106D1 - Teccor Electronics, Inc.

Thyristor Product Catalog +1 972-580-7777

Selected Packages*

U.L. RECOGNIZED

File #E71639

(0.8 A to 10 A)

General Description

The Teccor line of sensitive SCR semiconductors are half-wave

unidirectional, gate-controlled rectifiers (SCR-thyristor) which

complement Teccor's line of power SCRs. This group of

packages offers ratings of 0.8 A to 10 A, and 200 V to 600 V with

gate sensitivities of 12 µA to 500 µA. For gate currents in the

10 mA to 50 mA ranges, see “SCRs” section of this catalog.

The TO-220 and TO-92 are electrically isolated where the case

or tab is internally isolated to allow the use of low-cost assembly

and convenient packaging techniques.

Teccor's line of SCRs features glass-passivated junctions to

ensure long-term device reliability and parameter stability.

Teccor's glass offers a rugged, reliable barrier against junction

contamination.

Tape-and-reel packaging is available for the TO-92 package.

Consult the factory for more information.

Variations of devices covered in this data sheet are available for

custom design applications. Consult the factory for more

information.

Features

• Electrically-isolated TO-220 package

• High voltage capability — up to 600 V

• High surge capability — up to 100 A

• Glass-passivated chip

Compak Features

• Surface mount package — 0.8 A series

• New small-profile three-leaded Compak package

• Four gate sensitivities available

• Packaged in embossed carrier tape with 2,500

devices per reel

• Can replace SOT-223

TO-202

TO-92

3-lead

Compak

*TO-220

Isolated

TO-252

D-Pak

TO-251

V-Pak

Sensitive SCRs Data Sheets

+1 972-580-7777 Thyristor Product Catalog

See “General Notes” on page E5 - 4 and “Electrical Specifications Notes” on page E5 - 5

TYPE

Part Number

VDRM &

VRRM IGT

IDRM &

IRRM VTM

Non-isolated

TO-92 TO-202

TO-251

V-Pak Compak

TO-252

D-Pak

(1)

Amps

Volts

(2) (12)

(14) (18)

µAmps

(20) (21)

µAmps

(3) (10)

Volts

See “Package Dimensions” section for variations. (11)

IT(RMS) IT(AV)

TC or TL =

25 °C

TC or TL =

100 °C

TC or TL =

110 °C

MAX MIN MAX MAX MAX

0.8 A

S2S1 0.8 0.51 200 12 2100 1.7

S4S1 0.8 0.51 400 12 2100 1.7

S6S1 0.8 0.51 600 12 2100 1.7

S2S2 0.8 0.51 200 50 2100 1.7

S4S2 0.8 0.51 400 50 2100 1.7

S6S2 0.8 0.51 600 50 2100 1.7

S2S 0.8 0.51 200 200 2100 1.7

S4S 0.8 0.51 400 200 2100 1.7

S6S 0.8 0.51 600 200 2100 1.7

S2S3 0.8 0.51 200 500 2100 1.7

S4S3 0.8 0.51 400 500 2100 1.7

S6S3 0.8 0.51 600 500 2100 1.7

EC103B 0.8 0.51 200 200 150 1.7

EC103D 0.8 0.51 400 200 150 1.7

EC103M 0.8 0.51 600 200 2100 1.7

EC103B1 0.8 0.51 200 12 150 1.7

EC103D1 0.8 0.51 400 12 150 1.7

EC103M1 0.8 0.51 600 12 2100 1.7

EC103B2 0.8 0.51 200 50 150 1.7

EC103D2 0.8 0.51 400 50 150 1.7

EC103M2 0.8 0.51 600 50 2100 1.7

EC103B3 0.8 0.51 200 500 150 1.7

EC103D3 0.8 0.51 400 500 150 1.7

EC103M3 0.8 0.51 600 500 2100 1.7

2N5064 0.8 0.51 200 200 150 1.7

2N6565 0.8 0.51 400 200 1100 1.7

1.5 A

TCR22-4 1.5 0.95 200 200 1 100 1.5

TCR22-6 1.5 0.95 400 200 1 100 1.5

TCR22-8 1.5 0.95 600 200 2 100 1.5

T106B1 42.5 200 200 2100 2.2

T106D1 42.5 400 200 2100 2.2

T106M1 42.5 600 200 2100 2.2

T107B1 42.5 200 500 2100 2.5

T107D1 42.5 400 500 2100 2.5

T107M1 42.5 600 500 2100 2.5

S2004VS1 S2004DS1 42.5 200 50 2100 1.6

S4004VS1 S4004DS1 42.5 400 50 2100 1.6

S6004VS1 S6004DS1 42.5 600 50 2100 1.6

S2004VS2 S2004DS2 42.5 200 200 2100 1.6

S4004VS2 S4004DS2 42.5 400 200 2100 1.6

S6004VS2 S6004DS2 42.5 600 200 2100 1.6

Data Sheets Sensitive SCRs

Thyristor Product Catalog +1 972-580-7777

See “General Notes” on page E5 - 4 and “Electrical Specifications Notes” on page E5 - 5

VGT IHIGM VGRM PGM PG(AV) ITSM dv/dt di/dt tgt tql2t

(4) (12) (22)

Volts

(5) (15)

(16) (19)

mAmps

(17)

Amps Volts

(17)

Watts Watts

(6) (7) (13)

Amps

Volts/µSec Amps/µSec

(8)

µSec

(9)

µSec Amps2/Sec

TC or TL =

-40 °C

TC or TL =

25 °C

TC or TL =

110 °C 60/50 Hz

MAX MAX MIN MIN TYP (23) TYP MAX

1.2 0.8 0.2 51510.1 20/16 20 50 260 1.6

1.2 0.8 0.2 51510.1 20/16 10 50 260 1.6

1.2 0.8 0.25 51510.1 20/16 25 50 360 1.6

1.2 0.8 0.25 51510.1 20/16 10 50 360 1.6

1.2 0.8 0.25 51510.1 20/16 30 50 450 1.6

1.2 0.8 0.25 51510.1 20/16 15 50 450 1.6

1.2 0.8 0.25 81510.1 20/16 40 50 545 1.6

1.2 0.8 0.25 81510.1 20/16 20 50 545 1.6

1.2 0.8 0.25 51510.1 20/16 30 50 3.5 50 1.6

1.2 0.8 0.25 51510.1 20/16 15 50 3.5 50 1.6

1.2 0.8 0.2 51510.1 20/16 20 50 260 1.6

1.2 0.8 0.2 51510.1 20/16 10 50 260 1.6

1.2 0.8 0.25 51510.1 20/16 25 50 360 1.6

1.2 0.8 0.25 51510.1 20/16 10 50 360 1.6

1.2 0.8 0.25 81510.1 20/16 40 50 545 1.6

1.2 0.8 0.25 81510.1 20/16 20 50 545 1.6

1.2 0.8 0.25 51510.1 20/16 25 50 2.2 60 1.6

1.2 0.8 0.25 51610.1 20/16 25 50 2.2 60 1.6

1 0.80.2551610.120/1660 50 3.550 1.6

1 0.80.2551610.120/1640 50 3.550 1.6

1 0.80.2551610.120/1630 50 3.550 1.6

10.8 0.2 51610.1 20/16 850 450 1.6

10.8 0.2 61610.1 20/16 850 545 1.6

10.8 0.2 41610.1 30/25 850 350 3.7

10.8 0.2 61610.1 30/25 850 450 3.7

Sensitive SCRs Data Sheets

+1 972-580-7777 Thyristor Product Catalog

Specific Test Conditions

di/dt — Maximum rate-of-change of on-state current; IGT = 50 mA pulse

width ³15 µsec with £0.1 µs rise time

dv/dt — Critical rate-of-rise of forward off-state voltage

I2t — RMS surge (non-repetitive) on-state current for period of 8.3 ms

for fusing

IDRM and IRRM — Peak off-state current at VDRM and VRRM

IGT — DC gate trigger current VD = 6 V dc; RL = 100 W

IGM — Peak gate current

IH — DC holding current; initial on-state current = 20 mA

IT — Maximum on-state current

ITSM — Peak one-cycle forward surge current

PG(AV) — Average gate power dissipation

PGM — Peak gate power dissipation

tgt — Gate controlled turn-on time gate pulse = 10 mA; minimum

width = 15 µS with rise time £0.1 µs

tq — Circuit commutated turn-off time

VDRM and VRRM — Repetitive peak off-state forward and reverse voltage

VGRM — Peak reverse gate voltage

VGT — DC gate trigger voltage; VD = 6 V dc; RL = 100 W

VTM — Peak on-state voltage

General Notes

• Teccor 2N5064 and 2N6565 Series devices conform to all JEDEC

registered data. See specifications table on pages E5 - 2 and

E5 - 3.

• The case lead temperature (TC or TL) is measured as shown on

dimensional outline drawings in the “Package Dimensions” section

of this catalog.

• All measurements (except IGT) are made with an external resistor

RGK = 1 kW unless otherwise noted.

• All measurements are made at 60 Hz with a resistive load at an

ambient temperature of +25 °C unless otherwise specified.

• Operating temperature (TJ) is -65 °C to +110 °C for EC Series

devices, -65 °C to +125 °C for 2N Series devices, -40 °C to

+125 °C for “TCR” Series, and -40 °C to +110 °C for all others.

• Storage temperature range (TS) is -65 °C to +150 °C for TO-92

devices, -40 °C to +150 °C for TO-202 and Compak devices, and

-40 °C to +125 °C for all others.

• Lead solder temperature is a maximum of +230 °C for 10 seconds

maximum ³1/16" (1.59 mm) from case.

TYPE

Part Number

VDRM &

VRRM IGT

IDRM &

IRRM VTM

Isolated Non-isolated

TO-220 TO-202

TO-251

V-Pak

TO-252

D-Pak

(1)

Amps

Volts

(2) (12)

µAmps

(20) (21)

µAmps

(3) (10)

Volts

See “Package Dimensions” section for variations. (11)

IT(RMS) IT(AV)

TC =

25 °C

TC =

110 °C

MAX MAX MIN MAX MAX MAX MAX

S2006LS2 S2006FS21 S2006VS2 S2006DS2 63.8 200 200 5250 1.6

S4006LS2 S4006FS21 S4006VS2 S4006DS2 63.8 400 200 5250 1.6

S6006LS2 S6006FS21 S6006VS2 S6006DS2 63.8 600 200 5250 1.6

S2006LS3 S2006FS31 S2006VS3 S2006DS3 63.8 200 500 5250 1.6

S4006LS3 S4006FS31 S4006VS3 S4006DS3 63.8 400 500 5250 1.6

S6006LS3 S6006FS31 S6006VS3 S6006DS3 63.8 600 500 5250 1.6

S2008LS2 S2008FS21 S2008VS2 S2008DS2 8 5.1 200 200 5 250 1.6

S4008LS2 S4008FS21 S4008VS2 S4008DS2 8 5.1 400 200 5 250 1.6

S6008LS2 S6008FS21 S6008VS2 S6008DS2 8 5.1 600 200 5 250 1.6

S2008LS3 S2008FS31 S2008VS3 S2008DS3 8 5.1 200 500 5 250 1.6

S4008LS3 S4008FS31 S4008VS3 S4008DS3 8 5.1 400 500 5 250 1.6

S6008LS3 S6008FS31 S6008VS3 S6008DS3 8 5.1 600 500 5 250 1.6

10 A

S2010LS2 S2010FS21 S2010VS2 S2010DS2 10 6.4 200 200 5250 1.6

S4010LS2 S4010FS21 S4010VS2 S4010DS2 10 6.4 400 200 5250 1.6

S6010LS2 S6010FS21 S6010VS2 S6010DS2 10 6.4 600 200 5250 1.6

S2010LS3 S2010FS31 S2010VS3 S2010DS3 10 6.4 200 500 5250 1.6

S4010LS3 S4010FS31 S4010VS3 S4010DS3 10 6.4 400 500 5250 1.6

S6010LS3 S6010FS31 S6010VS3 S6010DS3 10 6.4 600 500 5250 1.6

Data Sheets Sensitive SCRs

Thyristor Product Catalog +1 972-580-7777

Electrical Specifications Notes

(1) See Figure E5.1 through Figure E5.9 for current ratings at

specified operating temperatures.

(2) See Figure E5.10 for IGT versus TC or TL.

(3) See Figure E5.11 for instantaneous on-state current (iT) versus on-

state voltage (vT) TYP.

(4) See Figure E5.12 for VGT versus TC or TL.

(5) See Figure E5.13 for IH versus TC or TL.

(6) For more than one full cycle, see Figure E5.14.

(7) 0.8 A to 4 A devices also have a pulse peak forward current on-

state rating (repetitive) of 75 A. This rating applies for operation at

60 Hz, 75 °C maximum tab (or anode) lead temperature, switching

from 80 V peak, sinusoidal current pulse width of 10 µs minimum,

15 µs maximum. See Figure E5.20 and Figure E5.21.

(8) See Figure E5.15 for tgt versus IGT.

(9) Test conditions as follows:

– TC or TL £80 °C, rectangular current waveform

– Rate-of-rise of current £10 A/µs

– Rate-of-reversal of current £5A/µs

– ITM = 1 A (50 µs pulse), Repetition Rate = 60 pps

– VRRM = Rated

– VR = 15 V minimum, VDRM = Rated

– Rate-of-rise reapplied forward blocking voltage = 5 V/µs

– Gate Bias = 0 V, 100 W (during turn-off time interval)

(10) Test condition is maximum rated RMS current except TO-92

devices are 1.2 APK; T106/T107 devices are 4 APK.

(11) See package outlines for lead form configurations. When ordering

special lead forming, add type number as suffix to part number.

(12) VD = 6 V dc, RL = 100 W (See Figure E5.19 for simple test circuit

for measuring gate trigger voltage and gate trigger current.)

(13) See Figure E5.1 through Figure E5.9 for maximum allowable case

temperature at maximum rated current.

(14) IGT = 500 µA maximum at TC = -40 °C for T106 devices

(15) IH = 10 mA maximum at TC = -65 °C for 2N5064 Series and

2N6565 Series devices

(16) IH = 6 mA maximum at TC = -40 °C for T106 devices

(17) Pulse Width £10 µs

(18) IGT = 350 µA maximum at TC = -65 °C for 2N5064 Series and

2N6565 Series devices

(19) Latching current can be higher than 20 mA for higher IGT types.

Also, latching current can be much higher at -40 °C. See Figure

E5.18.

(20) TC or TL = TJ for test conditions in off state

(21) IDRM and IRRM = 50 µA for 2N5064 and 100 µA for 2N6565 at

125 °C

(22) TO-92 devices specified at -65 °C instead of -40 °C

(23) TC = 110 °C

VGT IHIGM VGRM PGM PG(AV) ITSM dv/dt di/dt tgt tql2t

(4) (12) (22)

Volts

(5) (19)

mAmps

(17)

Amps Volts

(17)

Watts Watts

(6) (13)

Amps

Volts/µSec

Amps/µSec

(8)

µSec

(9)

µSec Amps2Sec

TC =

-40 °C

TC =

25 °C

TC =

110 °C TC = 110 °C

MAX MAX MIN 60/50 Hz TYP TYP MAX

10.8 0.25 6 1 6 1 0.1 100/83 10 100 450 41

10.8 0.25 6 1 6 1 0.1 100/83 8100 450 41

10.8 0.25 8 1 6 1 0.1 100/83 10 100 545 41

10.8 0.25 8 1 6 1 0.1 100/83 8100 545 41

1 0.8 0.25 6 1 6 1 0.1 100/83 10 100 4 50 41

1 0.8 0.25 6 1 6 1 0.1 100/83 8 100 4 50 41

1 0.8 0.25 8 1 6 1 0.1 100/83 10 100 5 45 41

1 0.8 0.25 8 1 6 1 0.1 100/83 8 100 5 45 41

10.8 0.25 6 1 6 1 0.1 100/83 10 100 450 41

10.8 0.25 6 1 6 1 0.1 100/83 8100 450 41

10.8 0.25 8 1 6 1 0.1 100/83 10 100 545 41

10.8 0.25 8 1 6 1 0.1 100/83 8100 545 41

Sensitive SCRs Data Sheets

+1 972-580-7777 Thyristor Product Catalog

*Mounted on 1 cm2 copper foil surface; two-ounce copper foil

Electrical Isolation

Teccor’s isolated sensitive SCRs will withstand a minimum high

potential test of 2500 V ac rms from leads to mounting tab over

the device's operating temperature range. The following table

shows other standard and optional isolation ratings.

*UL Recognized File #E71639

**For 4000 V isolation, use “V” suffix in part number.

Figure E5.1 Maximum Allowable Case Temperature versus

RMS On-state Current

Figure E5.2 Maximum Allowable Case Temperature versus

RMS On-state Current

Figure E5.3 Maximum Allowable Case Temperature versus

Average On-state Current

Thermal Resistance (Steady State)

RqJC [Rq JA] °C/W (TYPICAL)

Package Code ELF2FCDV

Type

TO-92 TO-220 TO-202

Type 2, 4, & 41

TO-202

Type 1 & 3

Compak TO-252

D-Pak

TO-251

V-Pak

0.8 A 75 [160] 60*

1.5 A 50 [160]

4.0 A 10 [100] 6.2 [80] 3.0 3.8 [85]

6.0 A 4.0 [65] 4.3 1.8 2.4

8.0 A 3.4 3.9 1.5 2.1

10.0 A 3.0 3.4 1.45 1.72

Electrical Isolation *

from Leads to Mounting Tab

V AC RMS TO-220

2500 Standard

4000 Optional **

100

110

120

130

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measured

as Shown on Dimensional Drawing

RMS On-State Current [I

T(RMS)

] – Amps

Maximum Allowable

Case Temperature (T

– ˚C

Compak

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

EC Series

JEDEC 2N Series

0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0

100

110

120

130

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measured

as Shown on Dimensional Drawing

RMS On-state Current [IT(RMS)] – Amps

Maximum Allowable Case Temperature (TC) – ˚C

2.6

4 A TO-251

and TO-252

T106 and T107

Type 1 and 3

T106 and T107

Type 2 and 4

TCR22 Devices

0 0.1 0.2 0.3 0.4 0.5 0.6

100

110

120

130

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measured

as Shown on Dimensional Drawing

Average On-state Current [I

T(AV)

] – Amps

Maximum Allowable Case Temperature (T

) – ˚C

0.51

Compak

EC Series

JEDEC 2N Series

Data Sheets Sensitive SCRs

Thyristor Product Catalog +1 972-580-7777

Figure E5.4 Maximum Allowable Case Temperature versus

Average On-state Current

Figure E5.5 Maximum Allowable Ambient Temperature versus

On-state Current

Figure E5.6 Maximum Allowable Ambient Temperature versus

RMS On-state Current

Figure E5.7 Maximum Allowable Ambient Temperature versus

Average On-state Current

Figure E5.8 Maximum Allowable Case Temperature versus

RMS On-state Current

Figure E5.9 Maximum Allowable Case Temperature versus

Average On-state Current

0 0.5 1.0 1.5 2.0 2.5 3.0

100

110

120

130

Average On-state Current [IT(AV)] – Amps

Maximum Allowable

Case Temperature (TC) – ˚C

0.95

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180

CASE TEMPERATURE: Measured

as Shown on Dimensional Drawing

1.65 1.9 2.54

T106 and T107

Type 1 and 3

T106 and T107

Type 2 and 4

TCR22

Devices

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9

140

120

100

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

FREE AIR RATING

1.5 A and JEDEC

2N Series I

T(AV)

and EC Series I

T(AV)

On-state Current – Amps

Maximum Allowable Ambient Temperature (T

) – ˚C

1.5 A Devices

and JEDEC

2N Series I

T(RMS)

EC Series I

T(RMS)

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

140

120

100

RMS On-state Current [IT(RMS)] – Amps

Maximum Allowable

Ambient Temperature (TA) – ˚C

2.0

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

FREE AIR RATING

TO-220

T106/T107 TO-202

Type 1 and 3

T106/T107 TO-202

Type 2 and 4

and TO-251

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4

100

120

140

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180

FREE AIR RATING

Average On-state Current [IT(AV)] – Amps

Maximum Allowable

Ambient Temperature (TA) – ˚C

TO-220

T106/T107 TO-202

Type 1 and 3

T106/T107 TO-202

Type 2 and 4

and TO-251

246 8100

100

105

110

115

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

TEMPERATURE: Measured as

Shown on Dimensional Drawings

RMS On-state Current [IT(RMS)] – Amps

Maximum Allowable

Case Temperature (TC) – ˚C

6 A TO-220

and TO-202

8 A TO-220

and TO-202

10 A TO-220

and TO-202

6 A TO-251

and TO-252

8 A TO-251

and TO-252

10 A TO-251

and TO-252

134560

100

105

110

Average On-state Current [IT(AV)] – Amps

Maximum Allowable

Case Temperature (TC) – ˚C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measured

as Shown on Dimensional Drawings

6 A TO-220

and TO-202

8 A TO-220

and TO-202

10 A TO-220

and TO-202

6 A TO-251

and TO-252

8 A TO-251

and TO-252

10 A TO-251

and TO-252

Sensitive SCRs Data Sheets

+1 972-580-7777 Thyristor Product Catalog

Figure E5.10 Normalized DC Gate-Trigger Current versus

Case Temperature

Figure E5.11 Instantaneous On-state Current versus

On-state Voltage (Typical)

Figure E5.12 Normalized DC Gate-Trigger Voltage versus

Case Temperature

Figure E5.13 Normalized DC Holding Current versus Case Temperature

-65 -15 +25 +65 +110 +125-40

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

Case Temperature (TC) – ˚C

Ratio of IGT

IGT (TC = 25 ˚C)

See General Notes for specific device

operating temperature range.

0 .6 .8 1.0 1.2 1.4 1.6

TC = 25˚C

6 A to 10 A Devices

0.8 A to 1.5 A TO-92,

T106/T107, and

Compak

Instantaneous On-state Voltage (vT) – Volts

Instantaneous On-state Current (iT) – Amps

4 A TO-251 and TO-252

-65 -15 +25 +65 +110 +125-40

0.5

1.0

1.5

2.0

Case Temperature (TC) – ˚C

Ratio of VGT

VGT (TC = 25 ˚C)

See General Notes for specific

operating temperature range

-65 -40 -15 +25 +65 +110 +125

1.0

2.0

3.0

4.0

See General Notes for specific

operating temperature range.

Case Temperature (TC) – ˚C

Ratio of I

= 25 ˚C)

Data Sheets Sensitive SCRs

Thyristor Product Catalog +1 972-580-7777

Figure E5.14 Peak Surge On-state Current versus Surge Current Duration

Figure E5.15 Typical Turn-on Time versus Gate Trigger Current

Figure E5.16 Power Dissipation (Typical) versus RMS On-state Current

1 2 3 4 5 6 8 10 20 30 40 50 60 80 100 200 300 400 600 100

100

200

SUPPLY FREQUENCY: 60 Hz Sinusoidal

LOAD: Resistive

RMS ON-STATE CURRENT: [IT(RMS)]: Max

Rated Value at Specified Case Temperature

Sur

e Current Duration – Full Cycles

Peak Surge (Non-repetitive)

On-state Current (ITSM) – Amps

Notes:

1) Gate control may be lost during

and immediately following surge

current interval.

2) Overload may not be repeated

until junction temperature has

returned to steady-state rated value.

6 A Devices

8 A Devices

10 A Devices

4 A TO-251 and TO-252

1.5 A Devices

TO-106

and TO-107

0.8 A TO-92

and Compak

0.01 0.1 1 10 100

0.1

1.0

100

= 50 µA MAX

= 200 µA MAX

= 500 µA MAX

= 25 ˚C

= 12 µA MAX

DC Gate Trigger Current (I

) – mA

Turn-on Time (t

) – µs

01234

1.0

2.0

3.0

4.0

5.0

T106 and T107

0.8 A TO-92 and Compak

1.5 A Devices

RMS On-state Current [I

T(RMS)

] – Amps

Average On-state Power Dissipation [P

D(AV)

] – Watts

CURRENT WAVEFORM: Half Sine Wave

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

4 A TO-251 and TO-252

Sensitive SCRs Data Sheets

+1 972-580-7777 Thyristor Product Catalog

Figure E5.17 Power Dissipation (Typical) versus RMS On-state Current

Figure E5.18 Normalized DC Latching Current versus Case Temperature

Figure E5.19 Simple Test Circuit for Gate Trigger Voltage and

Current Measurement

Note: V1 — 0 V to 10 V dc meter

VGT — 0 V to 1 V dc meter

IG — 0 mA to 1 mA dc milliammeter

R1 — 1 k potentiometer

To measure gate trigger voltage and current, raise gate voltage

(VGT) until meter reading V1 drops from 6 V to 1 V. Gate trigger

voltage is the reading on VGT just prior to V1 dropping. Gate trig-

ger current IGT can be computed from the relationship

where IG is reading (in amperes) on meter just prior to V1 drop-

ping.

Note: IGT may turn out to be a negative quantity (trigger current

flows out from gate lead).

024681

RMS On-state Current [IT(RMS)] – Amps

CURRENT WAVEFORM: Half Sine Wave

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

Average On-state

Power Dissipation [PD(AV)] – Watts

6 A to 10 A

TO-220, TO-202,

TO-251, and TO-252

-65 -15 +25 +65 +110 +125-40

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

Case Temperature (TC) – ˚C

Ratio of IL

IL (TC = 25 ˚C)

See General Notes for specific device

operating temperature range.

6 V

–

100

D.U.T.

Reset

Normally-closed

Pushbutton

1 k

(1%)

100

IN4001

IGT IG

VGT

1000

------------- Amps–=

Data Sheets Sensitive SCRs

Thyristor Product Catalog +1 972-580-7777

Figure E5.20 Peak Repetitive Capacitor Discharge Current

Figure E5.21 Peak Repetitive Sinusoidal Curve

180

160

140

120

100

1.0 3.0 5.0 7.0 10 30 50 70 100

Peak Discharge Current (ITM) – Amps

Peak Current Duration (tW) – µs

0.8 A to 4 A

ITM

tW = 5 TIME CONSTANTS

60 Hz

12 Hz

1 Hz

180

160

140

120

100

1.0 3.0 5.0 7.0 10 30 50 70 100

Peak Discharge Current (I

) – Amps

Peak Current Duration (t

) – µs

0.8 A to 4 A

ITM

60 Hz

12 Hz

1 Hz

Notes