Compact Chip Resistor Networks MNR14 (06034 size) Features 1) Convex electrodes Easy to check the fillet after soldering is finished. 2) Small, light, rectangular 4-chip network Area ratio is 65% smaller than that of MNR34, while weight ratio has been cut 75%. 3) High-density mounting Can be mounted even more densely than four 0603 chips (MCR03), and mounting costs are lower. 4) Compatible with a wide range of mounting equipment. Squared coners make it excellent for mounting using image recognition machines. 5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Ratings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70C. 0.063W (1 / 16W) at 70C POWER LOAD (%) 100 80 60 40 20 0 -55 0 70 100 125 AMBIENT TEMPERATURE (C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= PxR P: Rated power (W) Limiting element voltage R: Nominal resistance () Nominal resistance See Table 1. Operating temperature -55C to +155C Jumper type Resistance Rated current 50V Table 1 Max. 50m Resistance tolerance 1A Operating temperature -55C to +155C J (5%) F (1%) Resistance range () 2.2 to 9.1 (E6) Resistance temperature coefficient (ppm / C) 500 10 to 1M (E24) 200 10 to 1M (E24) 100 Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 1/3 2011.12 - Rev.H Data Sheet MNR14 (06034 size) Characteristics Guaranteed value Resistor type Jumper type Item J : 5% F : 1% Resistance Test conditions (JIS C 5201-1) Max. 50m Variation of resistance with temperature JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : -55 / +25 / +125C See Table.1 (2.0%+0.1) Overload JIS C 5201-1 4.13 Rated voltage (current) x2.5, 2s. Maximum Overload Voltage : 100V Max. 50m JIS C 5201-1 4.17 Rosin*Ethanol (25%WT) Soldering condition : 2355C Duration of immersion : 2.00.5s. A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability Resistance to soldering heat Rapid change of temperature (1.0%+0.05) Max. 50m No remarkable abnormality on the appearance. JIS C 5201-1 4.18 Soldering condition : 2605C Duration of immersion : 101s. (1.0%+0.05) Max. 50m JIS C 5201-1 4.19 Test temp. : -55C to +125C 5cyc (3.0%+0.1) Max. 100m JIS C 5201-1 4.24 40C, 93%RH Test time : 1,000h to 1,048h (3.0%+0.1) Max. 100m JIS C 5201-1 4.25.1 Rated voltage (current), 70C 1.5h : ON - 0.5h : OFF Test time : 1,000h to 1,048h (3.0%+0.1) Max. 100m JIS C 5201-1 4.25.3 125C Test time : 1,000h to 1,048h (1.0%+0.05) Max. 50m JIS C 5201-1 4.29 235C, Immersion cleaning, 50.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70C Endurance Resistance to solvent (1.0%+0.05) Max. 50m Without mechanical damage such as breaks. Bend strength of the end face plating JIS C 5201-1 4.33 Dimensions (Unit : mm) 0.40.15 0.30.2 0.8 3.20.1 3 4 1 Resistive element (Oxide metal thick film) 2 Silver thick film electrode 3 Nickel electrode 4 Sn electrode 5 Alumina substrate 6 Overcoating (Resin) 0.50.1 2 1.60.1 0.30.2 103 0.250.15 Material 0.30.2 0.60.15 6 Cross section A-A' 1 Marking may change to the one-character type. Pitch of the upper electrode. 5 6 1 Cross section B-B' 5 Equivalent circuit R1 R2 R3 R4 R1=R2=R3=R4 www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 2/3 2011.12 - Rev.H Data Sheet MNR14 (06034 size) Packaging Reel 02 04 06 08 08 06 D 04 B 02 A Taping P0 P2 D0 P1 E F W B0 C Label EIAJ ET-7200B (RRM) compliant A0 Heat crimp cover / Tape Chip network resistors Square punchout hole Thick paper (Underside paper tape) mount T2 (Unit : mm) A W F E A0 B0 8.00.3 3.50.05 1.750.1 1.80.1 3.40.1 D0 P0 P1 P2 T2 1.5 +0.1 0 4.00.1 4.00.1 2.00.05 Max. 1.1 B D Label C EIAJ ET-7200B (RRV) compliant (Unit : mm) A B C D 0 180 -3 60 +1 0 9 +1.0 0 130.2 Part No. Explanation M N R 1 4 E 0 A P Part No. J Resistance tolerance F J 1% 5% Nominal resistance Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance Resistance tolerance code J is also used for jumper F J : : 4 digits 3 digits Packaging Specifications Code Part No. Code MNR14 E0AP Resistance tolerance F(1%) J(5%) Packaging specifications Paper tape (4mm Pitch) Reel Basic ordering unit (pcs) 180mm (7in.) 5,000 Reel (180) : JEITA ET-7200B : Standard product www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 3/3 2011.12 - Rev.H Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. R1120A