38
11.08
D
Capacitance range:
33 pF to 0.033 mF (E12-values on request)
Rated voltages:
63 VDC, 100 VDC, 250 VDC, 400 VDC,
630 VDC, 800 VDC, 1000 VDC
Capacitance tolerances:
±10%, ±5%, ±2.5% (±2%, ±1.5% or ±1%
available as precision capacitors subject
to special enquiry)
Operating temperature range:
–55+ C to +100+ C
Test specifications:
In accordance with IEC 60384-13
and EN 131 800
Climatic test category:
55/100/56 in accordance with IEC
Insulation resistance at +20+ C:
5 x 105 M¸
(mean value: 1 x 106 M¸)
Measuring voltage:
Ur = 63 V: Utest = 50 V/1 min.
Ur 100 V: Utest = 100 V/1 min.
Dissipation factors at +20) C: tan d
at f C 1000 pF 1000 pF < C 4700 pF C > 4700 pF
1 kHz 3 x 10-4 4 x 10-4 4 x 10-4
10 kHz 3 x 10-4 4 x 10-4 4 x 10-4
100 kHz 4 x 10-4 5 x 10-4 –
1 MHz 10 x 10-4 – –
WIMA FKP 2
Polypropylene (PP) Film and Foil
Capacitors for Pulse Applications
in PCM 5 mm
Special Features Electrical Data
˜ Pulse duty construction
˜ Close tolerances up to ±2.5 %
(±1 % on request)
˜ Very low dissipation factor
˜ Negative capacitance change
versus temperature
˜ Very low dielectric absorption
˜ According to RoHS 2002/95/EC
Typical Applications
For high frequency applications e.g.
˜ Sample and hold
˜ Timing
˜ LC-Filtering
˜ Oscillating circuits
˜ Audio equipment
Construction
Dielectric:
Polypropylene (PP) film
Capacitor electrodes:
Metal foil
Internal construction:
Plastic film
Metal foil electrode
Terminating wire
Encapsulation:
Solvent-resistant, flame-retardant plastic
case with epoxy resin seal, UL 94 V-0
Terminations:
Tinned wire.
Marking:
Colour: Red. Marking: Black.
Epoxy resin seal: Yellow
Test voltage: 2 Ur, 2 sec.
Maximum pulse rise time:
1000 V/msec for pulses equal to the
rated voltage
Dielectric absorption:
0.05%
Temperature coefficient:
–200 x 10-6/+ C (typical)
Voltage derating:
A voltage derating factor of 1.35 % per K
must be applied from +85+ C for DC
voltages and from +75+ C for AC
voltages
Reliability:
Operational life 300 000 hours
Failure rate 5 fit (0.5 x Ur and 40+ C)
Mechanical Tests
Pull test on leads:
10 N in direction of leads according to
IEC 60068-2-21
Vibration:
6 hours at 10 ... 2000 Hz and 0.75 mm
displacement amplitude or 10 g in
accordance with IEC 60068-2-6
Low air density:
1kPa = 10 mbar in accordance with
IEC 60068-2-13
Bump test:
4000 bumps at 390 m/sec2 in
accordance with IEC 60068-2-29
Packing
Available taped and reeled.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
39
11.08
D
Capac-
63 VDC/40 VAC* 100 VDC/63 VAC* 250 VDC/160 VAC* 400 VDC/220 VAC* 630 VDC/250 VAC* 800 VDC/250 VAC* 1000 VDC/250 VAC*
itance W H L
PCM
**
W H L
PCM
**
W H L
PCM
**
W H L
PCM
**
W H L
PCM
**
W H L
PCM
**
W H L
PCM
**
33 pF 4.5 6 7.2 5
47 „ 4.5 6 7.2 5
68 „ 4.5 6 7.2 5
100 pF 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5
150 „ 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5
220 „ 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5
330 „ 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5
470 „ 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 5.5 7 7.2 5 5.5 7 7.2 5
680 „ 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 5.5 7 7.2 5 5.5 7 7.2 5
1000 pF 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 5.5 7 7.2 5 6.5 8 7.2 5
1500 „ 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 5.5 7 7.2 5 7.2 8.5 7.2 5
2200 „ 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 4.5 6 7.2 5 5.5 7 7.2 5 6.5 8 7.2 5 8.5 10 7.2 5
3300 „ 4.5 6 7.2 5 5.5 7 7.2 5 5.5 7 7.2 5 5.5 7 7.2 5 6.5 8 7.2 5 7.2 8.5 7.2 5
4700 „ 4.5 6 7.2 5 5.5 7 7.2 5 6.5 8 7.2 5 6.5 8 7.2 5 6.5 8 7.2 5 8.5 10 7.2 5
6800 „ 4.5 6 7.2 5 5.5 7 7.2 5 6.5 8 7.2 5 7.2 8.5 7.2 5 7.2 8.5 7.2 5
0.01 mF 5.5 7 7.2 5 6.5 8 7.2 5 7.2 8.5 7.2 5 8.5 10 7.2 5 8.5 10 7.2 5
0.015 „ 6.5 8 7.2 5 7.2 8.5 7.2 5 8.5 10 7.2 5
0.022 „ 7.2 8.5 7.2 5 8.5 10 7.2 5
0.033 „ 8.5 10 7.2 5
* AC voltage: f 1000 Hz; 1.4 x Urms + UDC Ur
** PCM = Printed circuit module = lead spacing.
E12 values and individual values available
from 27 pF up on request.
Dims. in mm.
Taped version see page 121. d = 0.5 P
Rights reserved to amend design data without prior notification.
Continuation
General Data
Permissible AC voltage
in relation to frequency
at 10) C internal temperature rise
(general guide).
WIMA FKP 2
1 10 100 1000
f/MHz
3 5 7 3 5 7
7
5
3
7
5
3
10
1
0.1
0.01
Z
-- 33 pF
-- 47 pF
-- 100 pF
-- 220 pF
-- 470 pF
-- 1000 pF
-- 2200 pF
-- 4700 pF
-- 0.01 µF
-- 0.022 µF
-- 0.033 µF
Impedance change with frequency
(general guide).
5
PCM
at the lead exit points
( 0.5)
L
W
H
d
6-2
630 VDC
800 VDC
1000 VDC
f
Hz
10 2 5 10 2 5 10 2 5 10
4 5 6 7
5
2
10
5
2
10
250
2
1
U
V
rms
470 pF
220 pF
2200 pF
4700 pF
1000 pF
0.01 µF
100 pF
33 pF
47 pF
16
11.08
D
Recommendation for Processing
and Application of
Through-Hole Capacitors
Soldering Process
A preheating of through-hole WIMA
capacitors is allowed for temperatures
Tmax 100 ° C.
In practice a preheating duration of
t 5 min. has been proven to be best.
Single wave soldering
Soldering bath temperature: T 260 ° C
Immersion time: t 5 sec
Double wave soldering
Soldering bath temperature: T 260 ° C
Immersion time: 2 x t 3 sec
Due to different soldering processes and
heat requirements the graphs are to be
regarded as a recommendation only.
2 s 3 s
30 60 90 120 150 180 210 240 sec][
t
T
260
240
220
200
180
160
140
120
100
80
60
40
20
[°C] 10 s
see detail-
enlargement
Wave soldering
Typical temperature/time graph for double wave soldering
WIMA Quality and Environmental Philosophy
ISO 9001:2000 Certification
ISO 9001:2000 is an international basic
standard of quality assurance systems for
all branches of industry. The approval
according to ISO 9001:2000 of our
factories by the VDE inspectorate certifies
that organisation, equipment and moni-
toring of quality assurance in our factories
correspond to internationally recognized
standards.
WIMA WPCS
The WIMA Process Control System (WPCS)
is a quality surveillance and optimization
system developed by WIMA. WPCS is a
major part of the quality-oriented WIMA
production. Points of application of WPCS
during production process:
” incoming material inspection
” metallization
” film inspection
” schoopage
” pre-healing
” lead attachment
” cast resin preparation/
encapsulation
” 100% final inspection
” AQL check
WIMA Environmental Policy
All WIMA capacitors, irrespective of
whether through-hole devices or SMD,
are made of environmentally friendly
materials. Neither during manufacture
nor in the product itself any toxic
substances are used, e.g.
– Lead – PBB/PBDE
– PCB – Arsenic
– CFC – Cadmium
– Hydrocarbon chloride – Mercury
– Chromium 6+ – etc.
We merely use pure, recyclable materials
for packing our components, such as:
” carton
” cardboard
” adhesive tape made of paper
” polystyrene
We almost completely refrain from using
packing materials such as:
” foamed polystyrene (Styropor®)
” adhesive tapes made of plastic
” metal clips
RoHS Compliance
According to the RoHS Directive 2002/95/EC
certain hazardous substances like e.g. lead,
cadmium, mercury must not be used any
longer in electronic equipment as of July 1st,
2006. For the sake of the environment WIMA
has refraind from using such substances since
years already.
Tape for lead-free WIMA capacitors
DIN EN ISO 14001:2005
WIMA’s environmental management has
been established in accordance with the
guidelines of DIN EN ISO 14001:2005.
The certification has been granted in
June 2006.
121
11.08
D
P
P1
P0
P2
F
d
P
P1
H1
H
P0
d
P2
F
t
D0
W2
Vh
W0
P1
P2
P0
P
H1
H
W
1
W
d
F
Diagram 1:
PCM 2.5/5/7.5mm
Diagram 3: PCM 22.5 and 27.5*mm
*PCM 27.5 taping possible with two feed holes between components
Diagram 2: PCM 10/15 mm
Dimensions for Radial Taping
Designation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping
Carrier tape width W 18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
Hold-down tape width W
0
6.0 for hot-sealing 6.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing
adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape
Hole position W
1
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
Hold-down tape position W
2
0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max.
Feed hole diameter D
0
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
Pitch of component P 12.7
p1.0
12.7
p1.0
12.7
p1.0
25.4
p1.0
25.4
p1.0
38.1
p1.5
3
*8.1
p1.5
or 50.8
p1.5
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
Feed hole pitch P
0
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
Feed hole centre P
1
5.1
p0.5
3.85
p0.7
2.6
p0.7
7.7
p0.7
5.2
p0.7
7.8
p0.7
5.3
p0.7
to lead
Hole centre to P
2
6.35
p1.3
6.35
p1.3
6.35
p1.3
12.7
p1.3
12.7
p1.3
19.05
p1.3
19.05
p1.3
component centre
Feed hole centre to bottom H
v
16.5
p0.3
16.5
p0.3
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
edge of the component 18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
Feed hole centre to top H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
edge of the component 32.25 max. 32.25 max. 24.5 to 31.5 25.0 to 31.5 26.0 to 37.0 30.0 to 43.0 35.0 to 45.0
Lead spacing at F 2.5
p0.5
5.0
+0.8
7.5
p0.8
10.0
p0.8
15
p0.8
22.5
p0.8
27.5
p0.8
upper edge of carrier tape
–0.2
Lead diameter d 0.4
p0.05
0.5
p0.05
„
0.5
p0.05
or
0.6
–0.05
„
0.5
p0.05
or
0.6
–0.05
0.8
–0.05
0.8
–0.05
0.8
–0.05
Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max.
Total tape thickness t 0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
ROLL/AMMO AMMO
Package
v
(see also page 122)
Unit see details page 124.
v
Please give „H“ dimensions and desired packaging type when ordering. Dims in mm.
„ Diameter of leads see General Data. Please clarify customer-specific deviations with the manufacturer.
* PCM 10 and PCM 15 can be crimped to PCM 7.5.
Position of components according to PCM 7.5 (sketch 1). P0 = 12.7 or 15.0 is possible
REEL
P 360 max.
B
52 p2 depending on
P 30 p1 58 p2 comp. dimensions
52 p2 54 p2 depending
REEL
P 360 max. B 58 p2
or
REEL
P 500 max. B 60 p2 on PCM and
P 30 p1 66 p2 P 25 p1 68 p2 component dimensions
+0.06 +0,06 +0,08 +0,08 +0.08
Typical Dimensions for
Taping Configuration
