PHG600-3 - Bosch - Datasheet.Live

Parameter Value Units Notes

General

Pressure Ranges –50 to 300 mmHg –0.97 psi to 5.8 psi

Overpressure 125 psi minimum

Electrical @ 72°F (22°C) Unless Otherwise Stated

Input Excitation 1 to 10 VDC Calibrated for 6 VDC

DielectricBreakdown 10,000 VDC 5

Risk Current 2 µA Maximum (per AAMI), 5

Input Impedance 1800 to 3300 Ω

Output Impedance 285 to 315 Ω

Environmental

Temperature

Compensated 15°C to 40°C °C (59° to 104°F)

Operating 15°C to 40°C °C (59° to 104°F)

Storage –25°C to 70°C °C (–13° to 158°F)

Humidity 10 to 90 %

Light Sensitivity 1 mmHg maximum (per AAMI BP22)

Operating Product Life 168 hours

Shelf Life 5 years

Mechanical

Weight <0.0044 lb (<2 g)

Media Interface Medical grade, dielectric gel

Gel Tube Interface

Material

Polycarbonate

Parameter Units Minimum Type Maximum Notes

Performance Parameters*

Offset mmHg –20 0 20

Sensitivity µV/V/mmHg 4.95 5 5.05

Calibration mmHg 97.5 100 102.5 2

Symmetry % — — ±5

Linearity (–30 to 100 mmHg) mmHg — — 1 6

Linearity (100 to 200 mmHg) % output — — 1 6

Linearity (200 to 300 mmHg) % output — — 1.5 6

ThermalCoefcientOffset mmHg/°C — — ±0.3 3

ThermalCoefcientSpan %/°C — — ±0.1 3

Frequency Response Hz 1200 — — 5

Phase Shift degrees — — 5 5

Offset Drift mmHg/8 hrs — — 1 4,5

* 1. All values measured at 6 VDC and 71.6°F (22°C) and after five second warm up unless

otherwise specified.

2. Output of sensor with no pressure applied and a 150 kΩ resistor shorted across +IN to +OUT.

3. Over a temperature range of 59°F to 104°F (15°C to 40°C).

4. Normalized offset/bridge voltage—8 hours after 20 seconds. warm-up.

5. Previously qualified, not tested in production.

6. Deviation from straight line drawn through zero and 100 mmHg data points.

7. These sensors are compatible with ETO (ethylene oxide) sterilization. The user is responsible for

establishing and validating suitable process conditions to prevent damage to the sensor.

NPC-100 and NPC-120

SeriesSpecications

The NovaSensor NPC-100 and NPC-120 Series pressure

sensorarespecicallydesignedforuseindisposable

medical applications. The devices are compensated and

calibrated per the Association for the Advancement of

Medical Instrumentation (AAMI) guidelines for industry

acceptability. The sensors integrate a high-performance,

pressuresensordiewithtemperaturecompensation

circuitryandgelprotectioninasmall,low-costpackage.

The NPC-100 and NPC-120 Series are manufactured

in a class 1000 clean-room to minimize possible

sources of contamination. A specially designed silicon

micromachined sensing element is used to meet or

exceedallindustryrequirementswhileminimizing

assembly and test cost for maximum customer

value.Thick-lmlaser-trimmingisemployedfornal

compensation and calibration. Sensitivity is maintained to

±1% and linearity is better than 1% in the physiological

operating pressure range.

The NPC-100 and NPC-120 Series are batch-

manufactured in ceramic plate form and shipped as

an intact array or in Tape and Reel for easy customer

automation.Thisassemblymethoddrawsfromwell-

established manufacturing techniques used in the

electronics industry in order to produce a quality, high

volume product.

NPC-100 Series pressure sensor port interface

NPC-100 Series package diagram

0.160 in to 0.170 in

(4.06 mm to 4.32 mm)

0.320 in +0.010/-0.002

(8.13 mm +0.25/-0.05)

0.010 in

(0.25 mm)

0.017 in

(0.43 mm)

0.415 in +0.010/-0.002

(10.54 mm +0.25/-0.05)

0.109 in to 0.119 in

(2.77 mm to 3.02 mm)

Gel height

+0.001 in/-0.035 in

(+0.025 mm/-0.89 mm)

Pressure

port Dielectric gel

Vent hole

Polycarbonate

gel tube2

Contact pads

1. Tolerances reflect typical flaring during the singulation process.

NPC-120 Series pressure sensor port interface

–

0.236 in to 0.246 in

(5.99 mm to 6.25 mm)

0.282 in to 0.290 in

(7.16 mm to 7.37 mm)

0.142 in to 0.145 in

(3.61 mm to 3.68 mm)

Radius 0.005 in

(0.13 mm) maximum

0.049 in to 0.052 in

(1.24 mm to 1.32 mm)

0.393 in to 0.397 in

(9.98 mm to 10.08 mm)

0.189 in to 0.192 in

(4.80 mm to 4.88 mm)

Material is clear Polycarbonate.

(2.22 mm to 2.30 mm)

0.0875 in to 0.0905 in

0.049 in to 0.052 in

(1.24 mm to 1.32 mm)

0.392 in to 0.397 in

(9.96 mm to 10.08 mm)

0.124 in to 0.126 in

(3.14 mm to 3.20 mm)

Radius 0.005 in

(0.13 mm) maximum

0.236 in to 0.246 in

(5.99 mm to 6.25 mm)

0.282 in to 0.290 in

(7.16 mm to 7.37 mm)

0.142 in to 0.145 in

(3.61 mm to 3.68 mm)

Material is clear Polycarbonate.

0.0875 in to 0.0905 in

(2.22 mm to 2.30 mm)

NPC-100 Series electrical interface

1. Tolerance on electrical pad location is ±0.010 in (±0.25 mm).

2. Contact pads are suitable for soldering.

3. Split pads on +Out and –Out must be connected for proper operation.

4. All dimensions assume a nominal 0.01 in (0.25 mm) distance between the

edge of the solder pads to the edge of the ceramic. This distance will vary

slightly from part to part.

Pinout

1 +In

2 +Out

3 -Out

4 -In

0.000 in (0 mm)

0.058 in (1.47 mm)

0.097 in (2.46 mm)

0.119 in (3.02 mm)

0.262 in (6.65 mm)

.069 in (1.75 mm)

0.000 in (0 mm)

4.35 in (110.5 mm)

0 in (0 mm)

4.35 in (110.5 mm)

1. Sensors are shipped as 120 UP snapstrates that must be singulated by

the customer.

2. Each reel or plate may include units that have failed visual or electrical

parameters as well as good units. Bad units are identified with a dot on the

backside of the cell location.

3. Reels and plates are shipped in dust free anti-static containers to

prevent contamination of the gel surface.

NPC-100 Series shipping

Configuration

Ordering Information

The code number to be ordered may be specified as follows:

NPC-100

NPC-120

Code Blank: Sold in 120-Up Snapstrate

T Tape and reel

NPC-1 0 - ___ Typical model number

NPC-100 Series schematic diagram

-Out

+Out

+In

-In

1 2 3 4

0.152 in (3.86 mm)

0.168 in (4.27 mm)

0.201 in (5.10 mm)

0.223 in (5.66 mm)