TECHNICAL DATA KK74AC175 Quad D Flip-Flop with Common Clock and Reset High-Speed Silicon-Gate CMOS The KK74AC175 is identical in pinout to the LS/ALS175, HC/HCT175. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALS outputs. This device consists of four D flip-flops with common Reset and Clock inputs, and separate D inputs. Reset (active-low) is asynchronous and occurs when a low level is applied to the Reset input. Information at a D input is transferred to the corresponding Q output on the next positivegoing edge of the Clock input. * Outputs Directly Interface to CMOS, NMOS, and TTL * Operating Voltage Range: 2.0 to 6.0 V * Low Input Current: 1.0 A; 0.1 A @ 25C * High Noise Immunity Characteristic of CMOS Devices * Outputs Source/Sink 24 mA ORDERING INFORMATION KK74AC175N Plastic KK74AC175D SOIC TA = -40 to 85 C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs PIN 16=VCC PIN 8 = GND Outputs Reset Clock D Q Q L X X L H H H H L H L L H H L X no change X = Don't care 1 KK74AC175 MAXIMUM RATINGS* Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin 20 mA IOUT DC Output Sink/Source Current, per Pin 50 mA ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 C 260 C VOUT IIN Tstg TL Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/C from 65 to 125C SOIC Package: : - 7 mW/C from 65 to 125C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) TJ Junction Temperature (PDIP) TA Operating Temperature, All Package Types IOH Output Current - High IOL Output Current - Low tr, tf * Parameter Input Rise and Fall Time (except Schmitt Inputs) * Min Max Unit 2.0 6.0 V 0 VCC V 140 C +85 C -24 mA 24 mA 150 40 25 ns/V -40 VCC =3.0 V VCC =4.5 V VCC =5.5 V 0 0 0 VIN from 30% to 70% VCC This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 KK74AC175 DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions Guaranteed Limits V 25 C -40C to 85C Unit VIH Minimum HighLevel Input Voltage VOUT=0.1 V or VCC-0.1 V 3.0 4.5 5.5 2.1 3.15 3.85 2.1 3.15 3.85 V VIL Maximum Low Level Input Voltage VOUT=0.1 V or VCC-0.1 V 3.0 4.5 5.5 0.9 1.35 1.65 0.9 1.35 1.65 V VOH Minimum HighLevel Output Voltage IOUT -50 A 3.0 4.5 5.5 2.9 4.4 5.4 2.9 4.4 5.4 V 3.0 4.5 5.5 2.56 3.86 4.86 2.46 3.76 4.76 3.0 4.5 5.5 0.1 0.1 0.1 0.1 0.1 0.1 VIN=VIH or VIL IOL=12 mA IOL=24 mA IOL=24 mA 3.0 4.5 5.5 0.36 0.36 0.36 0.44 0.44 0.44 Maximum Input Leakage Current VIN=VCC or GND 5.5 0.1 1.0 A IOLD +Minimum Dynamic Output Current VOLD=1.65 V Max 5.5 75 mA IOHD +Minimum Dynamic Output Current VOHD=3.85 V Min 5.5 -75 mA ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND 5.5 80 A * VIN=VIH or VIL IOH=-12 mA IOH=-24 mA IOH=-24 mA VOL Maximum LowLevel Output Voltage IOUT 50 A V * IIN 8.0 * All outputs loaded; thresholds on input associated with output under test. +Maximum test duration 2.0 ms, one output loaded at a time. Note: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC 3 KK74AC175 AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input tr=tf=3.0 ns) VCC* Symbol Parameter Guaranteed Limits 25 C V Min -40C to 85C Max Min Unit Max fmax Maximum Clock Frequency (Figure 1) 3.3 5.0 149 187 139 187 tPLH Propagation Delay, Clock to Q or Q (Figure 1) 3.3 5.0 2.0 1.5 12.0 9.0 2.0 1.0 13.5 9.5 ns tPHL Propagation Delay, Clock to Q or Q (Figure 1) 3.3 5.0 2.5 1.5 13.0 9.5 2.0 1.5 14.5 10.5 ns tPLH Propagation Delay, Reset to Q (Figure 2) 3.3 5.0 3.0 2.0 12.5 9.0 2.5 1.5 13.5 10.0 ns tPHL Propagation Delay, Reset to Q (Figure 2) 3.3 5.0 3.0 2.0 11.0 8.5 2.5 1.5 12.5 9.0 ns CIN Maximum Input Capacitance 5.0 4.5 MHz 4.5 pF Typical @25C,VCC=5.0 V CPD Power Dissipation Capacitance 45 pF Voltage Range 3.3 V is 3.3 V 0.3 V Voltage Range 5.0 V is 5.0 V 0.5 V * TIMING REQUIREMENTS (CL=50pF,Input tr=tf=3.0 ns) VCC* Symbol Parameter Guaranteed Limits V 25 C -40C to 85C Unit tsu Minimum Setup Time, Data to Clock (Figure 3) 3.3 5.0 4.5 3.0 4.5 3.0 ns th Minimum Hold Time, Clock to Data (Figure 3) 3.3 5.0 1.0 1.0 1.0 1.0 ns tw Minimum Pulse Width, Reset (Figure 2) 3.3 5.0 4.5 3.5 4.5 3.5 ns tw Minimum Pulse Width, Clock (Figure 1) 3.3 5.0 4.5 3.5 5.0 3.5 ns trec Minimum Recovery Time, Reset to Clock (Figure 2) 3.3 5.0 0 0 0 0 ns Voltage Range 3.3 V is 3.3 V 0.3 V Voltage Range 5.0 V is 5.0 V 0.5 V * 4 KK74AC175 Figure 1. Switching Waveforms Figure 2. Switching Waveforms Figure 3. Switching Waveforms EXPANDED LOGIC DIAGRAM 5 KK74AC175 N SUFFIX PLASTIC DIP (MS - 001BB) A Dimension, mm 9 16 Symbol MIN MAX A 18.67 19.69 B 6.1 7.11 B 1 8 5.33 C F L C D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 -T- SEATING PLANE N G K M H D J 0.25 (0.010) M T NOTES: 1. Dimensions "A", "B" do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. J 0 10 K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AC) Dimension, mm A 16 9 H B 1 G P 8 R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B 0.25 mm (0.010) per side. F M Symbol MIN MAX A 9.8 10 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G 1.27 H 5.72 J 0 8 K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 6