5WG1242-2AB01 - SIEMENS - Datasheet.Live

DELTA profil Pushbutton single UP 241 5WG1 241-2AB_1

UP 242 5WG1 242-2AB_1

Pushbutton

double UP 243 5WG1 243-2AB_1

UP 244 5WG1 244-2AB_1

Pushbutton

quadruple UP 245 5WG1 245-2AB_1

UP 246 5WG1 246-2AB_1

DELTA style Pushbutton single UP 285 5WG1 285-2AB_1

Pushbutton

double UP 286 5WG1 286-2AB_1

Pushbutton

quadruple UP 287 5WG1 287-2AB_1

As at: March 2008

Operating and mounting instructions

Products

Pushbutton single

Pushbutton double

Pushbutton quadruple

DELTA profil: cut-out frames ordered separately from the DELTA ranges

Frame

DELTA style: frames ordered separately from the DELTA ranges

Bus coupling unit bus coupling unit UP 110 or UP 114 ordered separately

Diagram 1: Mounting the pushbutton

C1 Bus coupling unit

C2 Frame

C3 Fixing screws *)

C4 Basic pushbutton module *)

C5 Rockers *)

C6 Mounting rack *)

C7 Recess *)

*) Scope of supply

Product and functional description

There is an upper and a lower operating field on the push-

buttons. In the middle of the pushbutton there is a note

panel in which pictograms can be inserted. This panel also

contains display elements (LEDs) for orientation lighting and

also for status indication. Opposing rockers are combined to

form a pair e.g. for defined switching, dimming, controlling

shutters and blinds.

It is also possible to carry out the switching functions ON and

OFF e.g. via a pushbutton “UP”.

Using an application program, the flush-mounted pushbut-

tons give commands via the flush-mounted bus coupler for

example to actuators for defined switching on/off, for dim-

ming lamps, raising/lowering shutters or for louvre adjust-

ment or other parameterisable functional units.

The device pushbutton is placed together with the relevant

DELTA frame on the flush-mounted bus coupler and can only

function in combination with the bus coupler UP and an ap-

propriate application program, i.e. the pushbutton (with bus

coupler UP) consist of the device (hardware) and the applica-

tion program (software).

The bus coupler UP and the relevant frame are not supplied

with the device but must be ordered separately.

Using the ETS program the application programs can be se-

lected and the specific parameters and addresses can be as-

signed.

Additional Informations

http://www.siemens.com/gamma

Technical data

Power supply

• via the flush-mounted bus coupler

Operating elements

• 1, 2 or 4 pairs of rockers, idle in the middle position

Display elements

• per pair of pushbuttons 1 LED red for status indication

e.g. quadruple pushbutton = 4 LEDs red

• 1 LED red for orientation light

Connections

• 10-pole plug connector (PEI): for connection to the flush-

mounted bus coupler

Mechanical data

• Dimensions:

- DELTA profil (L x W x D ): 65 x 65 x 11 mm

- DELTA style (L x W x D ): 68 x 68 x 14 mm

• Weight: approx. 40 g

Electrical safety

• Type of protection (according to EN 60529): IP 20

Environmental conditions

• Ambient operating temperature: - 5 ... + 45 °C

• Storage temperature: - 25 ... + 70 °C

• Relative humidity (not condensing): 5 % to 93 %

Markings

• KNX / EIB

Please turn over !

Location and function of the operating and display

elements

Pushbutton single

Pushbutton double

Pushbutton quadruple

Diagram 2: Location of display and operating elements

A1 Upper operating field

A2 LEDs for status indication

A3 LED as an orientation light

A4 Lower operating field

A5 Cover for pictograms

Mounting

• The device can be used for permanent interior installa-

tions, in dry rooms and for insertion in flush-type boxes.

V DANGER

JJJJJJJJJJJJJJJJJJJJJJJJJJ

• The device may only be installed and commissioned by an

authorised electrician.

• The device may not be inserted in the same box as 230 V

devices.

• The device may be used in switch sockets, if VDE

approved devices have been used.

• The prevailing safety and accident regulations must be

observed.

• The device may not be opened.

• For planning and construction of electric installations, the

relevant guidelines, regulations and standards of the re-

spective country are to be considered.

General description

The pushbutton is placed together with the relevant frame

on the flush-mounted bus coupler.

The flush-mounted bus coupler (C1) is connected in the

flush-type box and fixed in position (refer to the installation

instructions for the bus coupler).

Mounting sequence

• Place the basic pushbutton module (C4, diagram 3) with

the relevant frame (C2) on the flush-mounted bus coupler

(C1) and press the one strongly upon the other.

Using fixing screws:

• If the fixing screws (C3) are used first of all the rockers

(C5) have to be lifted out altogether. This can be achieved

by inserting the screwdriver between the frame in the re-

cess (C7) and applying leverage (diagram 4).

Important: The pushbutton module (C4, diagram 3) and

the rockers (C5) together with the frame (C2)

must be held down / pressed down.

• Screw down the fixing screws (C3).

• The rockers (C5) have to be orientated properly and

clicked upon the mounting rack (C6).

Diagram 3: mounting sequence

Drawing for mounting the fixing screws (C3)

Pushbutton single

Pushbutton double / pushbutton quadruple

Holding down as shown with pushbutton single

Diagram 4: Lifting out the rockers

Inserting pictograms

• Lift out the pictogram cover (A5) with the screwdriver by

applying leverage, during this hold down the pushbutton

module (C4).

DELTA profil

• Insert the screwdriver into the slot (A2) until it reaches

the stop and then wiggle it.

Diagram 5: Lifting out the pictogram cover

• Lay the pictograms onto the foundation.

• Snap on the pictogram cover (A5) again.

DELTA style

1) Insert the screwdriver between the frame and the

pushbutton module

2) Swivel the screwdriver towards the wall.

Diagram 6: Lifting out the pictogram cover

retaining tongue

pictogram

pictogram X)

foundation

Diagram 7: inserting the pictograms

• Snap on the pictogram cover (A5) again.

Dismantling

Without fixing screws

• Remove the pushbutton (C4) completely together with

the frame (C2) from the flush-mounted bus coupler (C1):

a) with the mere hand

b) with a screwdriver beneath the frame / wall

a) b)

Diagram 8: Dismantling

With fixing screws

• Remove the rockers as described at „Mounting / Using

fixing screws“.

• Screw out the fixing screws (C3).

• Snap on the rockers (C5) again.

• Remove the whole pushbutton module (C4) as described

at „ Without fixing screws “.

General Notes

• The operating instructions must be handed over

to the client.

• Any faulty device should be returned to the local

Siemens office.

• If you have further questions concerning the product

please contact our technical support:

! +49 (180) 5050-222

! +49 (180) 5050-223

" www.siemens.com/automation/support-request

251523.41.11

DS04

1) 2)