Transient Voltage Suppression Diodes Axial Leaded - 30000W > 30KPA series 30KPA Series RoHS Description Uni-directional The 30KPA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features * Typical maximum temperature coefficient VBR = 0.1% x VBR@25C x T Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25C unless otherwise noted) Parameter * Glass passivated chip junction in P600 package * 30000W peak pulse capability at 10x1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0 Volts to BV min * Excellent clamping capability * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) * EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) * Low incremental surge resistance * Typical IR less than 2A above 73V * High temperature soldering guaranteed: 260C/40 seconds / 0.375",(9.5mm) lead length, 5 lbs., (2.3kg) tension * Plastic package has underwriters laboratory flammability classification 94V-O * Matte tin lead-free plated * Halogen free and RoHS compliant Symbol Value Unit PPPM 30000 W Steady State Power Dissipation on Inifinite Heat Sink at TL=75C (Fig. 5) PD 8.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 400 A TJ , TSTG -55 to 175 C Typical Thermal Resistance Junction to Lead RuJL 8.0 C/W Applications Typical Thermal Resistance Junction to Ambient RuJA 40 C/W TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Peak Pulse Power Dissipation by 10x1000s Test Waveform (Fig.1) (Note 1) Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25C per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. Functional Diagram Bi-directional Cathode Anode Uni-directional (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 30KPA Series Bi-directional Transient Voltage Suppression Diodes Axial Leaded - 30000W > 30KPA series Electrical Characteristics.(TA=25C unless otherwise noted) MIN Test Current IT (mA) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @VR ( A) Maximum Clamping Voltage VC @ IPP (V) 31.28 33.51 36.90 40.20 43.60 46.90 48.00 50.30 53.60 57.00 60.30 64.80 67.00 71.50 73.70 78.20 79.30 80.40 83.80 87.10 93.80 100.50 107.20 113.90 120.60 134.00 147.40 160.80 167.60 174.30 178.70 187.70 189.90 201.10 221.20 50 50 50 50 20 10 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 606.0 548.9 517.9 490.3 450.9 420.8 415.1 391.5 371.3 350.7 331.5 327.9 297.1 291.3 283.2 278.0 271.7 265.8 253.8 234.9 217.7 207.0 194.2 183.0 172.9 155.9 142.3 135.8 129.8 123.7 120.0 111.2 110.2 104.3 94.7 5000 5000 5000 5000 2000 1000 1000 250 150 50 20 20 15 10 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 50.0 55.2 58.5 61.8 67.2 72.0 73.0 77.4 81.6 86.4 91.4 92.4 102.0 104.0 107.0 109.0 111.5 114.0 119.4 129.0 139.2 146.4 156.0 165.6 175.2 194.4 213.0 223.2 233.4 245.0 252.6 272.4 275.0 290.4 319.8 241.30 268.10 288.20 290.40 301.60 312.80 321.70 334.00 5 5 5 5 5 5 5 5 86.9 78.3 72.8 72.8 69.5 65.3 64.5 62.0 2 2 2 2 2 2 2 2 348.6 387.0 416.4 416.0 436.2 464.0 469.9 484.0 Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT 30KPA28A 30KPA30A 30KPA33A 30KPA36A 30KPA39A 30KPA42A 30KPA43A 30KPA45A 30KPA48A 30KPA51A 30KPA54A 30KPA58A 30KPA60A 30KPA64A 30KPA66A 30KPA70A 30KPA71A 30KPA72A 30KPA75A 30KPA78A 30KPA84A 30KPA90A 30KPA96A 30KPA102A 30KPA108A 30KPA120A 30KPA132A 30KPA144A 30KPA150A 30KPA156A 30KPA160A 30KPA168A 30KPA170A 30KPA180A 30KPA198A 30KPA216A 30KPA240A 30KPA258A 30KPA260A 30KPA270A 30KPA280A 30KPA288A 30KPA300A 30KPA28CA 30KPA30CA 30KPA33CA 30KPA36CA 30KPA39CA 30KPA42CA 30KPA43CA 30KPA45CA 30KPA48CA 30KPA51CA 30KPA54CA 30KPA58CA 30KPA60CA 30KPA64CA 30KPA66CA 30KPA70CA 30KPA71CA 30KPA72CA 30KPA75CA 30KPA78CA 30KPA84CA 30KPA90CA 30KPA96CA 30KPA102CA 30KPA108CA 30KPA120CA 30KPA132CA 30KPA144CA 30KPA150CA 30KPA156CA 30KPA160CA 30KPA168CA 30KPA170CA 30KPA180CA 30KPA198CA 28 30 33 36 39 42 43 45 48 51 54 58 60 64 66 70 71 72 75 78 84 90 96 102 108 120 132 144 150 156 160 168 170 180 198 30KPA216CA 30KPA240CA 30KPA258CA 30KPA260CA 30KPA270CA 30KPA280CA 30KPA288CA 30KPA300CA 216 240 258 260 270 280 288 300 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For bidirectional type having VRWM of 60 volts and less, the IR limit is double. For parts without A , the VBR is + 10% and Vc is 5% higher than with A parts. (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Axial Leaded - 30000W > 30KPA series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT Vc VBR VR V IT IR IR IT VR VBR Vc V Ipp Ipp PPPM Peak Pulse Power Dissipation -- Max power dissipation VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation VBR Breakdown Voltage -- Maximum current that flows though the TVS at a specified test current (IT) VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) IR Reverse Leakage Current -- Current measured at VR VF Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (TA=25C unless otherwise noted) Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve PPPM-Peak Pulse Power (kW) Voltage or Current Voltage Across TVS Current Through TVS 30KPA Series 1000 Voltage Transients 100 10 1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time continues on next page. (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Axial Leaded - 30000W > 30KPA series Ratings and Characteristic Curves (TA=25C unless otherwise noted) (Continued) Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 175 tr=10sec Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 10/1000sec. Waveform as defined by R.E.A td 0 200 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 1.0 0 TA-Ambient temperature (C) 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Derating Curve Cj, Junction Capacitance (pf) 10000 Uni-directional V= OV Uni-directional @ VR 100 Bi-directional @ VR Tj=25C f=1.0MHz Vsig=50mVp-p 1 0 50 100 150 200 250 VBR - Reverse Breakdown Voltage (V) 300 Steady State Power Dissipation (W) 9 Bi-directional V= OV 8 7 6 5 4 3 L = 0.375" (9.5mm) Lead Lengths 2 1 0 0 25 50 75 100 125 150 175 200 TL- Lead Temperature (C) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current IFSM, Peak Forward Surge Current (A) 450 400 350 300 250 200 150 100 50 0 1 10 100 Number of Cycles at 60 Hz (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Axial Leaded - 30000W > 30KPA series Soldering Parameters Lead-free assembly 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TL) to peak TL 3C/second max tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 3C/second max TS(max) to TL - Ramp-up Rate Reflow Ramp-up - Temperature Min (Ts(min)) 25C - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds t 25C to Peak Time (t) Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Flow/Wave Soldering (Solder Dipping) Ramp-down Rate 6C/second max Peak Temperature : 265C Time 25C to peak Temperature (TP) 8 minutes Max. Dipping Time : 10 seconds Do not exceed 280C Soldering : 1 time Physical Specifications Environmental Specifications Weight 0.07oz., 2.5g Temperature Cycle JESD22-A104 Case P600 molded plastic body over passivated junction. Pressure Cooker JESD 22-A102 Polarity Color band denotes the cathode except Bipolar. High Temp. Storage JESD22-A103 HTRB JESD22-A108 Terminal Matte Tin axial leads, solderable per JESD22-B102D. Thermal Shock JESD22-A106 Dimensions D Dimensions C A B P600 (DO-15) DO-204AC (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 A Inches Min Millimeters Max Min Max A 1.000 - 25.40 - B 0.340 0.360 8.60 9.10 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 30KPA Series Pre Heat tp TP Temperature (T) Reflow Condition Transient Voltage Suppression Diodes Axial Leaded - 30000W > 30KPA series Part Numbering System Part Marking System OPTION CODE: BLANK Reel Tape -B Bulk Packaging Cathode Band TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) F 30KPA xxx XX X YYWW Littelfuse Logo Trace Code Marking YY:Year Code WW: Week Code VR VOLTAGE 30KPAXXX SERIES CODE Product Type Packing Options Component Package Quantity Packaging Option 30KPAxxxXX P600 800 Tape & Reel 30KPAxxxXX-B P600 100 Bulk Part Number Packaging Specification EIA STD RS-296E Littelfuse Concord Packing Spec. DM-0016 Tape and Reel Specification Direction of Feed Top View Anode Lead White Type 2.75 (69.85) Front View Off Center 2.56 either side 2.062 (52.37) (65.00) 0.039(1.0) Negative Cathod Lead Red Type 0.40 (10.16) 0.048 (1.22) Recess Depth Max. 0.75 (19.05) 0.25 (6.35) 3.0 (76.2) 13.0 330.2 Dimensions are in inches/mm 0.68 (17.27) Label (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13