1716704-1 - KEMET ELECTRONICS

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63004

MULTILAYER CERAMIC CAPACITORS/AXIAL

&RADIAL LEADED

Multilayer ceramic capacitors are available in a

variety of physical sizes and configurations, including

leaded devices and surface mounted chips. Leaded

styles include molded and conformally coated parts

with axial and radial leads. However, the basic

capacitor element is similar for all styles. It is called a

chip and consists of formulated dielectric materials

which have been cast into thin layers, interspersed

with metal electrodes alternately exposed on opposite

edges of the laminated structure.

The entire structure is

fired at high temperature to produce a monolithic

block

which provides high capacitance values in a

small physical volume. After firing, conductive

terminations are applied to opposite ends of the chip to

make contact with the exposed electrodes.

Termination materials and methods vary depending on

the intended use.

TEMPERATURE CHARACTERISTICS

Ceramic dielectric materials can be formulated with

awide range of characteristics. The EIA standard for

ceramic dielectric capacitors (RS-198) divides ceramic

dielectrics into the following classes:

Class I: Temperature compensating capacitors,

suitable for resonant circuit application or other appli-

cations where high Q and stability of capacitance char-

acteristics are required. Class I capacitors have

predictable temperature coefficients and are not

affected by voltage, frequency or time. They are made

from materials which are not ferro-electric, yielding

superior stability but low volumetric efficiency.Class I

capacitors are the most stable type available, but have

the lowest volumetric efficiency.

Class II: Stable capacitors, suitable for bypass

or coupling applications or frequency discriminating

circuits where Q and stability of capacitance char-

acteristics arenot of major importance. Class II

capacitors have temperature characteristics of ± 15%

or less. They aremade from materials which are

ferro-electric, yielding higher volumetric efficiency but

less stability. Class II capacitors are affected by

temperature, voltage, frequency and time.

Class III: General purpose capacitors, suitable

for by-pass coupling or other applications in which

dielectric losses, high insulation resistance and

stability of capacitance characteristics are of little or

no importance. Class III capacitors are similar to Class

II capacitors except for temperature characteristics,

which are greater than ± 15%. Class III capacitors

have the highest vol

umetric efficiency and poorest

stability of any type.

KEMET leaded ceramic capacitors are offered in

the three most popular temperature characteristics:

C0G: Class I, with a temperature coefficient of 0 ±

30 ppm per degree C over an operating

temperature range of - 55°C to + 125°C (Also

known as “NP0”).

X7R: Class II, with a maximum capacitance

change of ± 15% over an operating temperature

range of - 55°Cto + 125°C.

Z5U: Class III, with a maximum capacitance

change of + 22% - 56% over an operating tem-

peraturerange of + 10°Cto + 85°C.

Specified electrical limits for these three temperature

characteristics areshown in Table 1.

SPECIFIED ELECTRICAL LIMITS

Table I

C0G X7R Z5U

Dissipation Factor: Measured at following conditions.

C0G – 1 kHz and 1 vrms if capacitance >1000pF

1 MHz and 1 vrms if capacitance 1000 pF

X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms

Z5U – 1 kHz and 0.5 vrms

0.10%

2.5%

(3.5% @ 25V)

4.0%

Dielectric Stength: 2.5 times rated DC voltage.

Insulation Resistance (IR): At rated DC voltage,

whichever of the two is smaller

1,000 M F

or 100 G

1,000 M F

or 100 G

1,000 M F

or 10 G

Temperature Characteristics: Range, °C

Capacitance Change without

DC voltage

-55 to +125

0 ± 30 ppm/°C

-55 to +125

± 15%

+ 10 to +85

+22%,-56%

* MHz and 1 vrms if capacitance 100 pF on military product.

Parameter

Temperature Characteristics

Pass Subsequent IR Test

ELECTRICAL CHARACTERISTICS

The fundamental electrical properties of multilayer

ceramic capacitors are as follows:

Polarity: Multilayer ceramic capacitors are not polar,

and may be used with DC voltage applied in either direction.

Rated Voltage: This term refers to the maximum con-

tinuous DC working voltage permissible across the entire

operating temperature range. Multilayer ceramic capacitors

are not extremely sensitive to voltage, and brief applications

of voltage above rated will not result in immediate failure.

However, reliability will be reduced by exposure to sustained

voltages above rated.

Capacitance:

The standard unit of capacitance is the

farad. For practical capacitors, it is usually expressed in

microfarads (10-6 farad), nanofarads (10-9 farad), or picofarads

(10-12 farad). Standard measurement conditions are as

follows:

Class I (up to 1,000 pF): 1MHz and 1.2 VRMS

maximum.

Class I (over 1,000 pF): 1kHz and 1.2 VRMS

maximum.

Class II: 1 kHz and 1.0 ± 0.2 VRMS.

Class III: 1 kHz and 0.5 ± 0.1 VRMS.

Like all other practical capacitors, multilayer ceramic

capacitors also have resistance and inductance. A simplified

schematic for the equivalent circuit is shown in Figure 1.

Other significant electrical characteristics resulting from

these additional properties are as follows:

Impedance: Since the parallel resistance (Rp) is nor-

mally very high, the total impedance of the capacitor is:

Figure 1

C = Capacitance

L = Inductance

RS=Equivalent Series Resistance (ESR)

RP=Insulation Resistance (IR)

Z =

Where Z = Total Impedance

RS = Equivalent Series Resistance

=Capacitive Reactance =

2ππfC

=Inductive Reactance = 2ππfL

+(X

- X

)

DF = ESR

Xc2πfC

Figure 2

ESR

The variation of a capacitor’s impedance with frequency

determines its effectiveness in many applications.

Dissipation Factor: Dissipation Factor (DF) is a mea-

sure of the losses in a capacitor under AC application. It is the

ratio of the equivalent series resistance to the capacitive reac-

tance

,and is usually expressed in percent. It is usually mea-

sured simultaneously with capacitance, and under the same

conditions. The vector diagram in Figure 2 illustrates the rela-

tionship between DF, ESR, and impedance. The reciprocal of

the dissipation factor is called the “Q”, or quality factor. For

convenience, the “Q” factor is often used for very low values

of dissipation factor. DF is sometimes called the “loss tangent”

or “tangent d”, as derived from this diagram.

Insulation Resistance: Insulation Resistance (IR) is the

DC resistance measured across the terminals of a capacitor,

represented by the parallel resistance (Rp) shown in Figure 1.

For a given dielectric type, electrode area increases with

capacitance, resulting in a decrease in the insulation resis-

tance. Consequently, insulation resistance is usually specified

as the “RC” (IR x C) product, in terms of ohm-farads or

megohm-microfarads. The insulation resistance for a specific

capacitance value is determined by dividing this product by

the capacitance. However, as the nominal capacitance values

become small, the insulation resistance calculated from the

RC product reaches values which are impractical.

Consequently, IR specifications usually include both a mini-

mum RC product and a maximum limit on the IR calculated

from that value. For example, a typical IR specification might

read “1,000 megohm-microfarads or 100 gigohms, whichever

is less.”

Insulation Resistance is the measure of a capacitor to

resist the flow of DC leakage current. It is sometimes referred

to as “leakage resistance.” The DC leakage current may be

calculated by dividing the applied voltage by the insulation

resistance (Ohm’s Law).

Dielectric Withstanding Voltage: Dielectric withstand-

ing voltage (DWV) is the peak voltage which a capacitor is

designed to withstand for short periods of time without dam-

age. All KEMET multilayer ceramic capacitors will withstand a

test voltage of 2.5 x the rated voltage for 60 seconds.

KEMET specification limits for these characteristics at

standard measurement conditions are shown in Table 1 on

page 4. Variations in these properties caused by changing

conditions of temperature, voltage, frequency, and time are

covered in the following sections.

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 5

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

Application Notes

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63006

TABLE 1

EIA TEMPERATURE CHARACTERISTIC CODES

FOR CLASS I DIELECTRICS

Significant Figure Multiplier Applied Tolerance of

of Temperature to Temperature Temperature

Coefficient Coefficient Coefficient *

PPM per Letter Multi- Number PPM per Letter

Degree C Symbol plier Symbol Degree C Symbol

0.0 C -1 0 ±30 G

0.3 B -10 1 ±60 H

0.9 A -100 2 ±120 J

1.0 M -1000 3 ±250 K

1.5 P -100000 4 ±500 L

2.2 R +1 5 ±1000 M

3.3 S +10 6 ±2500 N

4.7 T +100 7

7.5 U +1000 8

+10000 9

*These symetrical tolerances apply to a two-point measurement of

temperature coefficient: one at 25°C and one at 85°C. Some deviation

is permitted at lower temperatures. For example, the PPM tolerance

for C0G at -55°C is +30 / -72 PPM.

TABLE 2

EIA TEMPERATURE CHARACTERISTIC CODES

FOR CLASS II & III DIELECTRICS

Low Temperature High Temperature Maximum Capacitance

Rating Rating Shift

Degree Letter Degree Number Letter

Celcius Symbol Celcius Symbol Percent Symbol

+10C Z +45C 2 ±1.0% A

-30C Y +65C 4 ±1.5% B

-55C X +85C 5 ±2.2% C

+105C 6 ±3.3% D

+125C 7 ±4.7% E

+150C 8 ±7.5% F

+200C 9 ±10.0% P

±15.0% R

±22.0% S

+22/-33% T

+22/-56% U

+22/-82% V

+10 +20 +30 +40 +50 +60 +70 +80

Effect of Temperature: Both capacitance and dissipa-

tion factor are affected by variations in temperature. The max-

imum capacitance change with temperatureis defined by the

temperaturecharacteristic. However,this only defines a “box”

bounded by the upper and lower operating temperatures and

the minimum and maximum capacitance values. Within this

“box”, the variation with temperature depends upon the spe-

cific dielectric formulation. Typical curves for KEMET capaci-

tors are shown in Figures 3, 4, and 5. These figures also

include the typical change in dissipation factor for KEMET

capacitors.

Insulation resistance decreases with temperature.

Typically, the insulation resistance at maximum rated temper-

atureis 10% of the 25°Cvalue.

Effect of Voltage: Class I ceramic capacitors arenot

affected by variations in applied AC or DC voltages. For Class

II and III ceramic capacitors, variations in voltage affect only

the capacitance and dissipation factor.The application of DC

voltage higher than 5 vdc reduces both the capacitance and

dissipation factor. The application of AC voltages up to 10-20

Vac tends to increase both capacitance and dissipation factor.

At higher AC voltages, both capacitance and dissipation factor

begin to decrease.

Typical curves showing the effect of applied AC and DC

voltage are shown in Figure 6 for KEMET X7R capacitors and

Figure 7 for KEMET Z5U capacitors.

Effect of Frequency: Frequency affects both capaci-

tance and dissipation factor. Typical curves for KEMET multi-

layer ceramic capacitors are shown in Figures 8 and 9.

he variation of impedance with frequency is an impor-

tant consideration in the application of multilayer ceramic

capacitors. Total impedance of the capacitor is the vector of the

capacitive reactance, the inductive reactance, and the ESR, as

illustrated in Figure 2. As frequency increases, the capacitive

reactance decreases. However, the series inductance (L)

shown in Figure 1 produces inductive reactance, which

increases with frequency. At some frequency, the impedance

ceases to be capacitive and becomes inductive. This point, at

the bottom of the V-shaped impedance versus frequency

curves, is the self-resonant frequency. At the self-resonant fre-

quency, the reactance is zero, and the impedance consists of

the ESR only.

Typical impedance versus frequency curves for KEMET

multilayer ceramic capacitors areshown in Figures 10, 11, and

12. These curves apply to KEMET capacitors in chip form, with-

out leads. Lead configuration and lead length have a significant

impact on the series inductance. The lead inductance is

approximately 10nH/inch, which is large compared to the

inductance of the chip. The effect of this additional inductance

is a decrease in the self-resonant frequency,and an increase

in impedance in the inductive region above the self-resonant

frequency.

Effect of Time: The capacitance of Class II and III

dielectrics change with time as well as with temperature, volt-

age and frequency. This change with time is known as “aging.”

It is caused by gradual realignment of the crystalline structure

of the ceramic dielectric material as it is cooled below its Curie

temperature, which produces a loss of capacitance with time.

The aging process is predictable and follows a logarithmic

decay.Typical aging rates for C0G, X7R, and Z5U dielectrics

areas follows:

C0G None

X7R 2.0% per decade of time

Z5U 5.0% per decade of time

Typical aging curves for X7R and Z5U dielectrics are

shown in Figure 13.

The aging process is reversible. If the capacitor is heat-

ed to a temperature above its Curie point for some period of

time, de-aging will occur and the capacitor will regain the

capacitance lost during the aging process. The amount of de-

aging depends on both the elevated temperatureand the

length of time at that temperature. Exposure to 150°C for one-

half hour or 125°C for two hours is usually sufficient to return

the capacitor to its initial value.

Because the capacitance changes rapidly immediately

after de-aging, capacitance measurements are usually delayed

for at least 10 hours after the de-aging process, which is often

referred to as the “last heat.” In addition, manufacturers utilize

the aging rates to set factory test limits which will bring the

capacitance within the specified tolerance at some futuretime,

to allow for customer receipt and use. Typically, the test limits

areadjusted so that the capacitance will be within the specified

tolerance after either 1,000 hours or 100 days, depending on

the manufacturer and the product type.

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 7

Application Notes

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63008

POWER DISSIPATION

Power dissipation has been empirically determined for

two representative KEMET series: C052 and C062. Power dis-

sipation capability for various mounting configurations is shown

in Table 3. This table was extracted from Engineering Bulletin

F-2013, which provides a more detailed treatment of this sub-

ject.

Note that no significant difference was detected between

the two sizes in spite of a 2 to 1 surface area ratio. Due to the

materials used in the construction of multilayer ceramic capac-

itors, the power dissipation capability does not depend greatly

on the surface area of the capacitor body, but rather on how

well heat is conducted out of the capacitor lead wires.

Consequently, this power dissipation capability is applicable to

other leaded multilayer styles and sizes.

TABLE 3

POWER DISSIPATION CAPABILITY

(Rise in Celsius degrees per Watt)

Power

Mounting Configuration Dissipation

of C052 & C062

1.00" leadwires attached to binding post 90 Celsius degrees

of GR-1615 bridge (excellent heat sink) rise per Watt ±10%

0.25" leadwires attached to binding post 55 Celsius degrees

of GR-1615 bridge rise per Watt ±10%

Capacitor mounted flush to 0.062" glass- 77 Celsius degrees

epoxy circuit board with small copper traces rise per Watt ±10%

Capacitor mounted flush to 0.062" glass- 53 Celsius degrees

epoxy circuit board with four square inches rise per Watt ±10%

of copper land area as a heat sink

As shown in Table 3, the power dissipation capability of

the capacitor is very sensitive to the details of its use environ-

ment. The temperature rise due to power dissipation should not

exceed 20°C. Using that constraint, the maximum permissible

power dissipation may be calculated from the data provided in

Table 3.

It is often convenient to translate power dissipation capa-

bility into a permissible AC voltage rating. Assuming a sinu-

soidal wave form, the RMS “ripple voltage” may be calculated

The data necessary to make this calculation is included in

Engineering Bulletin F-2013. However,the following criteria

must be observed:

1. The temperature rise due to power dissipation

should be limited to 20°C.

2. The peak AC voltage plus the DC voltage must not

exceed the maximum working voltage of the

capacitor.

Provided that these criteria aremet, multilayer ceramic

E=Zx

Where E = RMS Ripple Voltage (volts)

P = Power Dissipation (watts)

Z = Impedance

R = ESR

MAX

capacitors may be operated with AC voltage applied without

need for DC bias.

RELIABILITY

Awell constructed multilayer ceramic capacitor is

extremely reliable and, for all practical purposes, has an infi-

nite life span when used within the maximum voltage and

temperature ratings. Capacitor failure may be induced by sus-

tained operation at voltages that exceed the rated DC voltage,

voltage spikes or transients that exceed the dielectric with-

standing voltage, sustained operation at temperatures above

the maximum rated temperature, or the excessive tempera-

ture rise due to power dissipation.

Failure rate is usually expressed in terms of percent per

1,000 hours or in FITS (failure per billion hours). Some

KEMET series are qualified under U.S. military established

reliability specifications MIL-PRF-20, MIL-PRF-123, MIL-

PRF-39014, and MIL-PRF-55681. Failure rates as low as

0.001% per 1,000 hours are available for all capacitance /

voltage ratings covered by these specifications. These spec-

ifications and

accompanying Qualified Products List should

be consulted for details.

For series not covered by these military specifications,

an internal testing program is maintained by KEMET Quality

Assurance. Samples from each week’s production are sub-

jected to a 2,000 hour accelerated life test at 2 x rated voltage

and maximum rated temperature. Based on the results of

these tests, the average failure rate for all non-military series

covered by this test program is currently 0.06% per 1,000

hours at maximum rated conditions. The failure rate would be

much lower at typical use conditions. For example, using MIL-

HDBK-217D this failure rate translates to 0.9 FITS at 50%

rated voltage and 50°C.

Current failure rate details for specific KEMET multilay-

er ceramic capacitor series areavailable on request.

MISAPPLICATION

Ceramic capacitors, like any other capacitors, may fail

if they aremisapplied. Typical misapplications include expo-

sure to excessive voltage, current or temperature. If the

dielectric layer of the capacitor is damaged by misapplication

the electrical energy of the circuit can be released as heat,

which may damage the circuit board and other components

as well.

If potential for misapplication exists, it is recommended

that precautions be taken to protect personnel and equipment

during initial application of voltage. Commonly used precau-

tions include shielding of personnel and sensing for excessive

power drain during board testing.

STORAGE AND HANDLING

Ceramic chip capacitors should be stored in normal

working environments. While the chips themselves are quite

robust in other environments, solderability will be degraded

by exposureto high temperatures, high humidity, corrosive

atmospheres, and long term storage. In addition, packaging

materials will be degraded by high temperature–reels may

soften or warp, and tape peel force may increase. KEMET

recommends that maximum storage temperature not exceed

40˚ C, and maximum storage humidity not exceed 70% rela-

tive humidity. In addition, temperature fluctuations should be

minimized to avoid condensation on the parts, and atmos-

pheres should be free of chlorine and sulfur bearing com-

pounds. For optimized solderability, chip stock should be

used promptly, preferably within 1.5 years of receipt.

from the following formula:

IMPEDANCE VS FREQUENCY

Impedance (Ohms)

110100 1,000

0.001

0.01

100

0.1

Frequency - MHz

Impedance vs Frequency for C0G Dielectric

Figure 10.

EFFECT OF FREQUENCY

-0.1

+0.2

-0.2

+0.1

0.10

0.20

0.0

Frequency - Hertz

Capacitance & DF vs Frequency - C0G

Figure 8.

%DF

Typical Aging Rates for X7R & Z5UFigure 13.

74%

76%

78%

80%

82%

84%

86%

88%

90%

92%

94%

96%

98%

100%

Capacitance

110100 1000 10K 100K

EFFECT OF TIME

%DF

-10

-5

-15

5.0

10.0

0.0

2.5

7.5

Frequency - Hertz

Capacitance & DF vs Frequency - X7R & Z5U

Figure 9.

.01μF.001μF

%ΔC

1001K 10K 100K1M 10M

%ΔC

%DF

Z5U

X7R

%DF

%ΔC

Impedance (Ohms)

110100 1,000

0.001

0.01

100

0.1

Frequency - MHz

Impedance vs Frequency for Z5U Dielectric

Figure 12.

Impedance (Ohms)

110100 1,000

0.001

0.01

100

0.1

Frequency - MHz

Impedance vs Frequency for X7R Dielectric

Figure 11.

0.1μF

1.0 μF

0.1μF.01μF

1.0 μF

Impedance vs. Frequency

Leaded Ceramic C0G

0.01

0.1

100

0.1 1 1 0100 1000

Frequency - MHz

Impedance (Ohms)

0.01µF

0.001µF

Leaded X7R

0.01

0.1

100

0.1 1 1 0100 1000

Frequency - MHz

Impedance (Ohms)

0.01µF

0.1µF

Impedance vs. Frequency

1.0µF

Impedance vs. Frequency

Leaded Z5U

0.01

0.1

100

0.1 1 1 0100 1000

Frequency - MHz

Impedance (Ohms)

0.1µF

1.0µF

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Capacitance

100%

74%

76%

78%

80%

82%

84%

86%

88%

90%

92%

94%

96%

98%

X7R

Z5U

1 10 100 1000 10K 100K

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 9

Application Notes

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

(hours)

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630034

CERAMIC MOLDED/AXIAL

&RADIAL — MIL-PRF-20

Lead Dia.

.025

(+.004

-.002)

.026

MIN.

.045

MAX.

1.25

MIN.

1.25

MIN.

Center Line of leads within .030" of Center Line of case.

1.25

MIN.

.026

MIN.

C052 (CC05, CCR05) C056 (CCR05)

C062 (CC06, CCR06), C512 (CC07, CCR07),

C522 (CC08, CCR08) C066 (CCR06)

Lead Dia.

.025

(+.004

-.002)

Lead Dia.

.025

(+.004

-.002)

Lead Dia.

.025

(+.004

-.002)

1.25

MIN.

DIMENSIONS — INCHES (MILLIMETERS)

1.50 Min.

(38.10)

1.50 Min.

(38.10)

CAPACITOR OUTLINE DRAWINGS - (AXIAL LEADS)

CAPACITOR OUTLINE DRAWINGS (AXIAL LEADS)

CAPACITOR OUTLINE DRAWINGS (RADIAL LEADS)

DIMENSIONS — INCHES (MILLIMETERS)

For packaging information, see pages 46, 47, and 48.

Note: Leads are .625 minimum when tape and reel packaged

*0.200 (5.08) maximum for 100,000 pF only.

Case

Size

Military

Equivalent Styles

Height

Length

Width

Lead

Spacing

C052/

C056 CC05, CCR05 .190 ± .010 (4.83 ± .25) .190 ± .010 (4.83 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)

C062/

C066 CC06, CCR06 .290 ± .010 (7.37 ± .25) .290 ± .010 (7.37 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)

C512 CC07, CCR07 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) *.140 ± .010 (3.56 ± .25) .400 ± .020 (10.16 ± .51)

C522 CC08, CCR08 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) .240 ± .010 (6.10 ± .25) .400 ± .020 (10.16 ± .51)

Case

Size

Military

Equivalent Styles

Length

Body Diameter

Lead Diameter

C114

CC75, CCR75 .160 ± .010 (4.06 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)

C124

CC76, CCR76 .250 ± .010 (6.35 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)

C192

CC77, CCR77 .390 ± .010 (9.91 ± .25) .140 ± .010 (3.56 ± .25) .025, +.004, -.001 (.64, +.10, -.025)

C202

CC78, CCR78 .500 ± .020 (12.70 ± .51) .250 ± .015 (6.35 ± .38) .025, +.004, -.001 (.64, +.10, -.025)

C222

CC79, CCR79 .690 ± .020 (17.53 ± .51) .350 ± .015 (8.89 ± .38) .025, +.004, -.001 (.64, +.10, -.025)

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 35

CC(R) 75, 76

ORDERING INFORMATION

CAPACITOR MARKING

JCK

2R2

CM5

11AK

“J” Brand (CCR only), Temperature Characteristic

Capacitance

Capacitance Tolerance, Failure Rate (CCR only),

Year Code

Lot Code, Trademark (K)

CCR0

5CH1

00FR

FRONT CC(R) 05

Military Designation (Type, Temperature Characteristic,

Capacitance, Tolerance, Failure Rate)

** For the standoff style, a “V” is added after the

failure rate, or last character.

0804

AJ3

1433

REAR

Date Code

Lot Code, “J” Brand (CCR only),

FSCM (Federal Source Code)

CCR77C

G102JM

J31433

0804A

Military Designation (Type, Temperature Characteristic,

Capacitance, Tolerance, Failure Rate)

“J” Brand (CCR only), FSCM (Federal Source Code)

Date/Lot Code

CC(R) 77

CCR78CG

103FR

JAN K

31433

100V

0804A

Military Designation (Type, Temperature Characteristic,

Capacitance, Tolerance, Failure Rate)

“JAN” Brand (CCR only), Trademark (K)

FSCM (Federal Source Code)

Voltage

Date/Lot Code

CC(R) 78

CCR79CG

103KM

JAN K

31433

200V

0804A

Military Designation (Type, Temperature Characteristic,

Capacitance, Tolerance, Failure Rate)

“JAN” Brand (CCR only), Trademark

FSCM (Federal Source Code)

Voltage

Date/Lot Code

CC(R) 79

CCR06

CG102

FRONT CC(R) 06

Military Designation (Type, Temperature Characteristic,

Capacitance, Tolerance, Failure Rate)

** For the standoff style, a “V” is added after the

failure rate, or last character.

0804A

J100V

31433

REAR

Date/LotCode

“J” Brand (CCR only), Voltage

FSCM (Federal Source Code)

CCR07CG

472KM

JAN KEMET

31433

200V 0804A

Military Designation (Type, Temperature Characteristic,

Capacitance, Tolerance, Failure Rate)

“JAN” Brand, Trademark

FSCM (Federal Source Code)

Voltage, Date/Lot Code

CC(R) 07

CCR08CG

472KM

JAN KEMET

31433

200V 0809A

Military Designation (Type, Temperature Characteristic,

Capacitance, Tolerance, Failure Rate)

“JAN” Brand, Trademark

FSCM (Federal Source Code)

Voltage, Date/Lot Code

CC(R) 08

MIL-PRF-20

CERAMIC MOLDED/AXIAL

&RADIAL — MIL-PRF-20

C052 G 102 J 1 G 5 C R

CERAMIC

CASE SIZE

See Table Below

SPECIFICATION

G – MIL-PRF-20

CAPACITANCE PICOFARAD CODE

Expressed in picofarads (pF). First two digits represent

significant figures. Third digit specifies number of zeros

following except 9 indicates division by 10). Examples:

0.1 µF = 100,000 pF = 104 and 9.1 pF = 919. See

tables for standard values.

CAPACITANCE TOLERANCE

Standard Others

K – ±10% G – ±2% C – ±0.25pF

J – ±5% F – ±1% D – ±0.5pF

B–±0.1pF

WORKING VOLTAGE DC

2–200V; 1 – 100V; 5 – 50V

FAILURE RATE

A – Not Applicable

M–1.0%

P– 0.1%

R–0.01%

S – 0.001%

LEAD MATERIAL

C–60/40 Tin/Lead (SnPb)

INTERNAL CONSTRUCTION

5 – Multilayer

TEMPERATURE CHARACTERISTIC

KEMET

Designator

Military

Equivalent

EIA

Equivalent

Capacitance Change with Temp.

Temp

Range,

°C

Measured with-

out DC Bias

Voltage

Measured

with Bias

(Rated Voltage)

(Ultra Stable)

*CG

(See below)

C0G

(NP0)

-55 to

+125°

±30

ppm/°C

±30

ppm/°C

Standard tolerances for each Series

are shown in the repetitive parts lists.

Case Sizes

Radial Axial

C052 C114

C056 C124

C062 C192

C066 C202

C512 C222

C522 Part Number Example: C052G102J1G5CR (14 digits – no spaces)

*CH – ±60 ppm/°C 8.2 pF-18.0 pF

*CJ – ±120 ppm/°C 4.3 pF-7.5 pF

*CK – ±250 ppm/°C 2.2 pF-3.9 pF

*CX – not measurable 0.1 pF-2.0 pF

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630036

CERAMIC MOLDED/AXIAL — MIL-PRF-20

ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)

RATINGS & PART NUMBER REFERENCE

CAP.

KEMET

PART NUMBER

MILITARY

STYLE CC

MILITARY

STYLE CCR

1.0 C114G109(2)2G5C(1) CC75CX1R0(2) CCR75CX1R0(2)(1)

1.1 C114G119(2)2G5C(1) CC75CX1R1(2) CCR75CX1R1(2)(1)

1.2 C114G129(2)2G5C(1) CC75CX1R2(2) CCR75CX1R2(2)(1)

1.3 C114G139(2)2G5C(1) CC75CX1R3(2) CCR75CX1R3(2)(1)

1.5 C114G159(2)2G5C(1) CC75CX1R5(2) CCR75CX1R5(2)(1)

1.6 C114G169(2)2G5C(1) CC75CX1R6(2) CCR75CX1R6(2)(1)

1.8 C114G189(2)2G5C(1) CC75CX1R8(2) CCR75CX1R8(2)(1)

2.0 C114G209(2)2G5C(1) CC75CX2R0(2) CCR75CX2R0(2)(1)

2.2 C114G229(2)2G5C(1) CC75CK2R2(2) CCR75CK2R2(2)(1)

2.4 C114G249(2)2G5C(1) CC75CK2R4(2) CCR75CK2R4(2)(1)

2.7 C114G279(3)2G5C(1) CC75CK2R7(3) CCR75CK2R7(3)(1)

3.0 C114G309(3)2G5C(1) CC75CK3R0(3) CCR75CK3R0(3)(1)

3.3 C114G339(3)2G5C(1) CC75CK3R3(3) CCR75CK2R3(3)(1)

3.6 C114G369(3)2G5C(1) CC75CK3R6(3) CCR75CK3R6(3)(1)

3.9 C114G399(3)2G5C(1) CC75CK3R9(3) CCR75CK3R9(3)(1)

4.3 C114G439(3)2G5C(1) CC75CJ4R3(3) CCR75CJ4R3(3)(1)

4.7 C114G479(3)2G5C(1) CC75CJ4R7(3) CCR75CJ4R7(3)(1)

5.1 C114G519(3)2G5C(1) CC75CJ5R1(3) CCR75CJ5R1(3)(1)

5.6 C114G569(3)2G5C(1) CC75CJ5R6(3) CCR75CJ5R6(3)(1)

6.2 C114G629(3)2G5C(1) CC75CJ6R2(3) CCR75CJ6R2(3)(1)

6.8 C114G689(3)2G5C(1) CC75CJ6R8(3) CCR75CJ6R8(3)(1)

7.5 C114G759(3)2G5C(1) CC75CJ7R5(3) CCR75CJ7R5(3)(1)

8.2 C114G829(3)2G5C(1) CC75CH8R2(3) CCR75CH8R2(3)(1)

9.1 C114G919(3)2G5C(1) CC75CH9R1(3) CCR75CH9R1(3)(1)

10.0 C114G100(4)2G5C(1) CC75CH100(4) CCR75CH100(4)(1)

11.0 C114G110(4)2G5C(1) CC75CH110(4) CCR75CH110(4)(1)

12.0 C114G120(4)2G5C(1) CC75CH120(4) CCR75CH120(4)(1)

13.0 C114G130(4)2G5C(1) CC75CH130(4) CCR75CH130(4)(1)

15.0 C114G140(4)2G5C(1) CC75CH140(4) CCR75CH140(4)(1)

16.0 C114G160(4)2G5C(1) CC75CH160(4) CCR75CH160(4)(1)

18.0 C114G180(4)2G5C(1) CC75CH180(4) CCR75CH180(4)(1)

20.0 C114G200(4)2G5C(1) CC75CG200(4) CCR75CG200(4)(1)

22.0 C114G220(4)2G5C(1) CC75CG220(4) CCR75CG220(4)(1)

24.0 C114G240(4)2G5C(1) CC75CG240(4) CCR75CG240(4)(1)

27.0 C114G270(4)2G5C(1) CC75CG270(4) CCR75CG270(4)(1)

30.0 C114G300(4)2G5C(1) CC75CG300(4) CCR75CG300(4)(1)

33.0 C114G330(4)2G5C(1) CC75CG330(4) CCR75CG330(4)(1)

36.0 C114G360(4)2G5C(1) CC75CG360(4) CCR75CG360(4)(1)

39.0 C114G390(4)2G5C(1) CC75CG390(4) CCR75CG390(4)(1)

43.0 C114G430(4)2G5C(1) CC75CG430(4) CCR75CG430(4)(1)

47.0 C114G470(4)2G5C(1) CC75CG470(4) CCR75CG470(4)(1)

51.0 C114G510(4)2G5C(1) CC75CG510(4) CCR75CG510(4)(1)

56.0 C114G560(4)2G5C(1) CC75CG560(4) CCR75CG560(4)(1)

62.0 C114G620(4)2G5C(1) CC75CG620(4) CCR75CG620(4)(1)

68.0 C114G680(4)2G5C(1) CC75CG680(4) CCR75CG680(4)(1)

75.0 C114G750(4)2G5C(1) CC75CG750(4) CCR75CG750(4)(1)

200 VOLT – C114 (CC(R)75 PER MIL-PRF-20/27)

CAP.

KEMET

PART NUMBER

MILITARY

STYLE CC

MILITARY STYLE

CCR

82.0 C114G820(4)1G5C(1) CC75CG820(4) CCR75CG820(4)(1)

91.0 C114G910(4)1G5C(1) CC75CG910(4) CCR75CG910(4)(1)

100.0 C114G101(4)1G5C(1) CC75CG101(4) CCR75CG101(4)(1)

110.0 C114G111(4)1G5C(1) CC75CG111(4) CCR75CG111(4)(1)

120.0 C114G121(4)1G5C(1) CC75CG121(4) CCR75CG121(4)(1)

130.0 C114G131(4)1G5C(1) CC75CG131(4) CCR75CG131(4)(1)

150.0 C114G151(4)1G5C(1) CC75CG151(4) CCR75CG151(4)(1)

160.0 C114G161(4)1G5C(1) CC75CG161(4) CCR75CG161(4)(1)

180.0 C114G181(4)1G5C(1) CC75CG181(4) CCR75CG181(4)(1)

200.0 C114G201(4)1G5C(1) CC75CG201(4) CCR75CG201(4)(1)

220.0 C114G221(4)1G5C(1) CC75CG221(4) CCR75CG221(4)(1)

240.0 C114G241(4)1G5C(1) CC75CG241(4) CCR75CG241(4)(1)

270.0 C114G271(4)5G5C(1) CC75CG271(4) CCR75CG271(4)(1)

300.0 C114G301(4)5G5C(1) CC75CG301(4) CCR75CG301(4)(1)

330.0 C114G331(4)5G5C(1) CC75CG331(4) CCR75CG331(4)(1)

360.0 C114G361(4)5G5C(1) CC75CG361(4) CCR75CG361(4)(1)

390.0 C114G391(4)5G5C(1) CC75CG391(4) CCR75CG391(4)(1)

430.0 C114G431(4)5G5C(1) CC75CG431(4) CCR75CG431(4)(1)

470.0 C114G471(4)5G5C(1) CC75CG471(4) CCR75CG471(4)(1)

510.0 C114G511(4)5G5C(1) CC75CG511(4) CCR75CG511(4)(1)

560.0 C114G561(4)5G5C(1) CC75CG561(4) CCR75CG561(4)(1)

620.0 C114G621(4)5G5C(1) CC75CG621(4) CCR75CG621(4)(1)

680.0 C114G681(4)5G5C(1) CC75CG681(4) CCR75CG681(4)(1)

82.0 C124G820(4)2G5C(1) CC76CG820(4) CCR76CG820(4)(1)

91.0 C124G910(4)2G5C(1) CC76CG910(4) CCR76CG910(4)(1)

100.0 C124G101(4)2G5C(1) CC76CG101(4) CCR76CG101(4)(1)

110.0 C124G111(4)2G5C(1) CC76CG111(4) CCR76CG111(4)(1)

120.0 C124G121(4)2G5C(1) CC76CG121(4) CCR76CG121(4)(1)

130.0 C124G131(4)2G5C(1) CC76CG131(4) CCR76CG131(4)(1)

270.0 C124G271(4)1G5C(1) CC76CG271(4) CCR76CG271(4)(1)

300.0 C124G301(4)1G5C(1) CC76CG301(4) CCR76CG301(4)(1)

330.0 C124G331(4)1G5C(1) CC76CG331(4) CCR76CG331(4)(1)

360.0 C124G361(4)1G5C(1) CC76CG361(4) CCR76CG361(4)(1)

390.0 C124G391(4)1G5C(1) CC76CG391(4) CCR76CG391(4)(1)

430.0 C124G431(4)1G5C(1) CC76CG431(4) CCR76CG431(4)(1)

470.0 C124G471(4)1G5C(1) CC76CG471(4) CCR76CG471(4)(1)

510.0 C124G511(4)1G5C(1) CC76CG511(4) CCR76CG511(4)(1)

560.0 C124G561(4)1G5C(1) CC76CG561(4) CCR76CG561(4)(1)

620.0 C124G621(4)1G5C(1) CC76CG621(4) CCR76CG621(4)(1)

680.0 C124G681(4)1G5C(1) CC76CG681(4) CCR76CG681(4)(1)

750.0 C124G751(4)5G5C(1) CC76CG751(4) CCR76CG751(4)(1)

820.0 C124G821(4)5G5C(1) CC76CG821(4) CCR76CG821(4)(1)

910.0 C124G911(4)5G5C(1) CC76CG911(4) CCR76CG911(4)(1)

1,000.0 C124G102(4)5G5C(1) CC76CG102(4) CCR76CG102(4)(1)

150.0 C192G151(4)2G5C(1) CC77CG151(4) CCR77CG151(4)(1)

160.0 C192G161(4)2G5C(1) CC77CG161(4) CCR77CG161(4)(1)

180.0 C192G181(4)2G5C(1) CC77CG181(4) CCR77CG181(4)(1)

200.0 C192G201(4)2G5C(1) CC77CG201(4) CCR77CG201(4)(1)

220.0 C192G221(4)2G5C(1) CC77CG221(4) CCR77CG221(4)(1)

240.0 C192G241(4)2G5C(1) CC77CG241(4) CCR77CG241(4)(1)

270.0 C192G271(4)2G5C(1) CC77CG271(4) CCR77CG271(4)(1)

300.0 C192G301(4)2G5C(1) CC77CG301(4) CCR77CG301(4)(1)

330.0 C192G331(4)2G5C(1) CC77CG331(4) CCR77CG331(4)(1)

360.0 C192G361(4)2G5C(1) CC77CG361(4) CCR77CG361(4)(1)

390.0 C192G391(4)2G5C(1) CC77CG391(4) CCR77CG391(4)(1)

430.0 C192G431(4)2G5C(1) CC77CG431(4) CCR77CG431(4)(1)

470.0 C192G471(4)2G5C(1) CC77CG471(4) CCR77CG471(4)(1)

510.0 C192G511(4)2G5C(1) CC77CG511(4) CCR77CG511(4)(1)

560.0 C192G561(4)2G5C(1) CC77CG561(4) CCR77CG561(4)(1)

620.0 C192G621(4)2G5C(1) CC77CG621(4) CCR77CG621(4)(1)

680.0 C192G681(4)2G5C(1) CC77CG681(4) CCR77CG681(4)(1)

200 VOLT – C192 (CC(R)77 PER MIL-PRF-20/29)

200 VOLT – C124 (CC(R)76 PER MIL-PRF-20/28)

100 VOLT – C124 (CC(R)76 PER MIL-PRF-20/28)

100 VOLT – C114 (CC(R)75 PER MIL-PRF-20/27)

50 VOLT – C114 (CC(R)75 PER MIL-PRF-20/27)

50 VOLT – C124 (CC(R)76 PER MIL-PRF-20/28)

To complete Part Number, insert the following letters:

(1) Available FailureRates: A (CC styles only); M, P, R & S (CCR styles only).

(2) Available Capacitance Tolerances: B, C.

(3) Available Capacitance Tolerances: B, C, D.

(4) Available Capacitance Tolerances: F, G, J.

RATINGS & PART NUMBER REFERENCE

To complete Part Number, insert the following letters:

(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).

(2) Available Capacitance Tolerances: B, C.

(3) Available Capacitance Tolerances: B, C, D.

(4) Available Capacitance Tolerances: F, G, J.

(5) Available Capacitance Tolerances: F, G, J, K.

MIL-PRF-20

CERAMIC MOLDED/AXIAL — MIL-PRF-20

ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)

CAP.

KEMET

PART NUMBER

MILITARY

STYLE CC

MILITARY

STYLE CCR

750.0 C192G751(4)1G5C(1) CC77CG751(4) CCR77CG751(4)(1)

820.0 C192G821(4)1G5C(1) CC77CG821(4) CCR77CG821(4)(1)

910.0 C192G911(4)1G5C(1) CC77CG911(4) CCR77CG911(4)(1)

1,000.0 C192G102(4)1G5C(1) CC77CG102(4) CCR77CG102(4)(1)

1,100.0 C192G112(4)1G5C(1) CC77CG112(4) CCR77CG112(4)(1)

1,200.0 C192G122(4)1G5C(1) CC77CG122(4) CCR77CG122(4)(1)

1,300.0 C192G132(4)1G5C(1) CC77CG132(4) CCR77CG132(4)(1)

1,500.0 C192G152(4)1G5C(1) CC77CG152(4) CCR77CG152(4)(1)

1,600.0 C192G162(4)1G5C(1) CC77CG162(4) CCR77CG162(4)(1)

1,800.0 C192G182(4)1G5C(1) CC77CG182(4) CCR77CG182(4)(1)

2,000.0 C192G202(4)1G5C(1) CC77CG202(4) CCR77CG202(4)(1)

2,200.0 C192G222(4)1G5C(1) CC77CG222(4) CCR77CG222(4)(1)

2,400.0 C192G242(4)5G5C(1) CC77CG242(4) CCR77CG242(4)(1)

2,700.0 C192G272(4)5G5C(1) CC77CG272(4) CCR77CG272(4)(1)

3,000.0 C192G302(4)5G5C(1) CC77CG302(4) CCR77CG302(4)(1)

3,300.0 C192G332(4)5G5C(1) CC77CG332(4) CCR77CG332(4)(1)

3,600.0 C192G362(4)5G5C(1) CC77CG362(4) CCR77CG362(4)(1)

3,900.0 C192G392(4)5G5C(1) CC77CG392(4) CCR77CG392(4)(1)

4,300.0 C192G432(4)5G5C(1) CC77CG432(4) CCR77CG432(4)(1)

4,700.0 C192G472(4)5G5C(1) CC77CG472(4) CCR77CG472(4)(1)

5,100.0 C192G512(5)5G5C(1) CC77CG512(5) CCR77CG512(5)(1)

5,600.0 C192G562(5)5G5C(1) CC77CG562(5) CCR77CG562(5)(1)

820.0 C202G821(5)2G5C(1) CC78CG821(5) CCR78CG821(5)(1)

1,000.0 C202G102(5)2G5C(1) CC78CG102(5) CCR78CG102(5)(1)

1,200.0 C202G122(5)2G5C(1) CC78CG122(5) CCR78CG122(5)(1)

1,500.0 C202G152(5)2G5C(1) CC78CG152(5) CCR78CG152(5)(1)

1,800.0 C202G182(5)2G5C(1) CC78CG182(5) CCR78CG182(5)(1)

2,200.0 C202G222(5)2G5C(1) CC78CG222(5) CCR78CG222(5)(1)

2,700.0 C202G272(5)2G5C(1) CC78CG272(5) CCR78CG272(5)(1)

3,300.0 C202G332(5)2G5C(1) CC78CG332(5) CCR78CG332(5)(1)

100 VOLT – C192 (CC(R)77 PER MIL-PRF-20/29)

50 VOLT – C192 (CC(R)77 PER MIL-PRF-20/29)

200 VOLT – C202 (CC(R)78 PER MIL-PRF-20/30)

CAP.

KEMET

PART NUMBER

MILITARY STYLE

CCR

3,900.0 C202G392(5)1G5C(1) CC78CG392(5) CCR78CG392(5)(1)

4,700.0 C202G472(5)1G5C(1) CC78CG472(5) CCR78CG472(5)(1)

5,600.0 C202G562(5)1G5C(1) CC78CG562(5) CCR78CG562(5)(1)

6,800.0 C202G682(5)1G5C(1) CC78CG682(5) CCR78CG682(5)(1)

8,200.0 C202G822(5)1G5C(1) CC78CG822(5) CCR78CG822(5)(1)

10,000.0 C202G103(5)1G5C(1) CC78CG103(5) CCR78CG103(5)(1)

12,000.0 C202G123(5)1G5C(1) CC78CG123(5) CCR78CG123(5)(1)

15,000.0 C202G153(5)5G5C(1) CC78CG153(5) CCR78CG153(5)(1)

18,000.0 C202G183(5)5G5C(1) CC78CG183(5) CCR78CG183(5)(1)

22,000.0 C202G223(5)5G5C(1) CC78CG223(5) CCR78CG223(5)(1)

27,000.0 C202G273(5)5G5C(1) CC78CG273(5) CCR78CG273(5)(1)

3,900.0 C222G392(5)2G5C(1) CC79CG392(5) CCR79CG392(5)(1)

4,700.0 C222G472(5)2G5C(1) CC79CG472(5) CCR79CG472(5)(1)

5,600.0 C222G562(5)2G5C(1) CC79CG562(5) CCR79CG562(5)(1)

6,800.0 C222G682(5)2G5C(1) CC79CG682(5) CCR79CG682(5)(1)

8,200.0 C222G822(5)2G5C(1) CC79CG822(5) CCR79CG822(5)(1)

10,000.0 C222G103(5)2G5C(1) CC79CG103(5) CCR79CG103(5)(1)

15,000.0 C222G153(5)1G5C(1) CC79CG153(5) CCR79CG153(5)(1)

18,000.0 C222G183(5)1G5C(1) CC79CG183(5) CCR79CG183(5)(1)

22,000.0 C222G223(5)1G5C(1) CC79CG223(5) CCR79CG223(5)(1)

27,000.0 C222G273(5)1G5C(1) CC79CG273(5) CCR79CG273(5)(1)

33,000.0 C222G333(5)1G5C(1) CC79CG333(5) CCR79CG333(5)(1)

39,000.0 C222G393(5)1G5C(1) CC79CG393(5) CCR79CG393(5)(1)

47,000.0 C222G473(5)5G5C(1) CC79CG473(5) CCR79CG473(5)(1)

56,000.0 C222G563(5)5G5C(1) CC79CG563(5) CCR79CG563(5)(1)

68,000.0 C222G683(5)5G5C(1) CC79CG683(5) CCR79CG683(5)(1)

82,000.0 C222G823(5)5G5C(1) CC79CG823(5) CCR79CG823(5)(1)

100 VOLT – C222 (CC(R)79 PER MIL-PRF-20/31)

50 VOLT – C222 (CC(R)79 PER MIL-PRF-20/31)

100 VOLT – C202 (CC(R)78 PER MIL-PRF-20/30)

200 VOLT – C222 (CC(R)79 PER MIL-PRF-20/31)

50 VOLT – C202 (CC(R)78 PER MIL-PRF-20/30)

CERAMIC MOLDED/RADIAL — MIL-PRF-20

ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)

RATINGS & PART NUMBER REFERENCE

Tocomplete Part Number, insert the following letters:

(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).

(2) Available Capacitance Tolerances: B, C.

(3) Available Capacitance Tolerances: B, C, D.

(4) Available Capacitance Tolerances: F, G, J.

(5) Available Capacitance Tolerances: F,G, J, K.

(6) Insert “2” for standard design, Style C052G Stand-offs are available

Insert “6” for stand-offdesign, Style C056G only as CCR’s, not available as CC.

(7) Add “V” for stand-offdesign, Style C056G

And leave blank for the flat bottom design (C052G)

}

CAP.

KEMET

PART NUMBER

MILITARY

STYLE CC

MILITARY

STYLE CCR

1.0 C05(6)G109(2)2G5C(1) CC05CX1R0(2) CCR05CX1R0(2)(1)(7)

1.1 C05(6)G119(2)2G5C(1) CC05CX1R1(2) CCR05CX1R1(2)(1)(7)

1.2 C05(6)G129(2)2G5C(1) CC05CX1R2(2) CCR05CX1R2(2)(1)(7)

1.3 C05(6)G139(2)2G5C(1) CC05CX1R3(2) CCR05CX1R3(2)(1)(7)

1.5 C05(6)G159(2)2G5C(1) CC05CX1R5(2) CCR05CX1R5(2)(1)(7)

1.6 C05(6)G169(2)2G5C(1) CC05CX1R6(2) CCR05CX1R6(2)(1)(7)

1.8 C05(6)G189(2)2G5C(1) CC05CX1R8(2) CCR05CX1R8(2)(1)(7)

2.0 C05(6)G209(2)2G5C(1) CC05CX2R0(2) CCR05CX2R0(2)(1)(7)

2.2 C05(6)G229(2)2G5C(1) CC05CK2R2(2) CCR05CK2R2(2)(1)(7)

2.4 C05(6)G249(2)2G5C(1) CC05CK2R4(2) CCR05CK2R4(2)(1)(7)

2.7 C05(6)G279(3)2G5C(1) CC05CK2R7(3) CCR05CK2R7(3)(1)(7)

3.0 C05(6)G309(3)2G5C(1) CC05CK3R0(3) CCR05CK3R0(3)(1)(7)

3.3 C05(6)G339(3)2G5C(1) CC05CK3R3(3) CCR05CK3R3(3)(1)(7)

3.6 C05(6)G369(3)2G5C(1) CC05CK3R6(3) CCR05CK3R6(3)(1)(7)

3.9 C05(6)G399(3)2G5C(1) CC05CK3R9(3) CCR05CK3R9(3)(1)(7)

4.3 C05(6)G439(3)2G5C(1) CC05CJ4R3(3) CCR05CJ4R3(3)(1)(7)

4.7 C05(6)G479(3)2G5C(1) CC05CJ4R7(3) CCR05CJ4R7(3)(1)(7)

5.1 C05(6)G519(3)2G5C(1) CC05CJ5R1(3) CCR05CJ5R1(3)(1)(7)

5.6 C05(6)G569(3)2G5C(1) CC05CJ5R6(3) CCR05CJ5R6(3)(1)(7)

6.2 C05(6)G629(3)2G5C(1) CC05CJ6R2(3) CCR05CJ6R2(3)(1)(7)

6.8 C05(6)G689(3)2G5C(1) CC05CJ6R8(3) CCR05CJ6R8(3)(1)(7)

7.5 C05(6)G759(3)2G5C(1) CC05CJ7R5(3) CCR05CJ7R5(3)(1)(7)

8.2 C05(6)G829(3)2G5C(1) CC05CH8R2(3) CCR05CH8R2(3)(1)(7)

9.1 C05(6)G919(3)2G5C(1) CC05CH9R1(3) CCR05CH9R1(3)(1)(7)

10.0 C05(6)G100(4)2G5C(1) CC05CH100(4) CCR05CH100(4)(1)(7)

11.0 C05(6)G110(4)2G5C(1) CC05CH110(4) CCR05CH110(4)(1)(7)

12.0 C05(6)G120(4)2G5C(1) CC05CH120(4) CCR05CH120(4)(1)(7)

13.0 C05(6)G130(4)2G5C(1) CC05CH130(4) CCR05CH130(4)(1)(7)

15.0 C05(6)G150(4)2G5C(1) CC05CH150(4) CCR05CH150(4)(1)(7)

16.0 C05(6)G160(4)2G5C(1) CC05CH160(4) CCR05CH160(4)(1)(7)

18.0 C05(6)G180(4)2G5C(1) CC05CH180(4) CCR05CH180(4)(1)(7)

20.0 C05(6)G200(4)2G5C(1) CC05CG200(4) CCR05CG200(4)(1)(7)

22.0 C05(6)G220(4)2G5C(1) CC05CG220(4) CCR05CG220(4)(1)(7)

24.0 C05(6)G240(4)2G5C(1) CC05CG240(4) CCR05CG240(4)(1)(7)

27.0 C05(6)G270(4)2G5C(1) CC05CG270(4) CCR05CG270(4)(1)(7)

30.0 C05(6)G300(4)2G5C(1) CC05CG300(4) CCR05CG300(4)(1)(7)

33.0 C05(6)G330(4)2G5C(1) CC05CG330(4) CCR05CG330(4)(1)(7)

36.0 C05(6)G360(4)2G5C(1) CC05CG360(4) CCR05CG360(4)(1)(7)

39.0 C05(6)G390(4)2G5C(1) CC05CG390(4) CCR05CG390(4)(1)(7)

43.0 C05(6)G430(4)2G5C(1) CC05CG430(4) CCR05CG430(4)(1)(7)

47.0 C05(6)G470(4)2G5C(1) CC05CG470(4) CCR05CG470(4)(1)(7)

51.0 C05(6)G510(4)2G5C(1) CC05CG510(4) CCR05CG510(4)(1)(7)

200 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)

CAP.

KEMET

PART NUMBER

MILITARY

STYLE CC

MILITARY STYLE

CCR

56.0 C05(6)G560(4)2G5C(1) CC05CG560(4) CCR05CG560(4)(1)(7)

62.0 C05(6)G620(4)2G5C(1) CC05CG620(4) CCR05CG620(4)(1)(7)

68.0 C05(6)G680(4)2G5C(1) CC05CG680(4) CCR05CG680(4)(1)(7)

75.0 C05(6)G750(4)2G5C(1) CC05CG750(4) CCR05CG750(4)(1)(7)

82.0 C05(6)G820(4)2G5C(1) CC05CG820(4) CCR05CG820(4)(1)(7)

91.0 C05(6)G910(4)2G5C(1) CC05CG910(4) CCR05CG910(4)(1)(7)

100.0 C05(6)G101(4)2G5C(1) CC05CG101(4) CCR05CG101(4)(1)(7)

110.0 C05(6)G111(4)2G5C(1) CC05CG111(4) CCR05CG111(4)(1)(7)

120.0 C05(6)G121(4)2G5C(1) CC05CG121(4) CCR05CG121(4)(1)(7)

130.0 C05(6)G131(4)2G5C(1) CC05CG131(4) CCR05CG131(4)(1)(7)

150.0 C05(6)G131(4)2G5C(1) CC05CG131(4) CCR05CG131(4)(1)(7)

160.0 C05(6)G161(4)2G5C(1) CC05CG161(4) CCR05CG161(4)(1)(7)

180.0 C05(6)G181(4)2G5C(1) CC05CG181(4) CCR05CG181(4)(1)(7)

200.0 C05(6)G201(4)2G5C(1) CC05CG201(4) CCR05CG201(4)(1)(7)

220.0 C05(6)G221(4)2G5C(1) CC05C221(4) CCR05CG221(4)(1)(7)

240.0 C05(6)G241(4)2G5C(1) CC05CG241(4) CCR05CG241(4)(1)(7)

270.0 C05(6)G271(4)2G5C(1) CC05CG271(4) CCR05CG271(4)(1)(7)

300.0 C05(6)G301(4)2G5C(1) CC05CG301(4) CCR05CG301(4)(1)(7)

330.0 C05(6)G331(4)2G5C(1) CC05CG331(4) CCR05CG331(4)(1)(7)

360.0 C05(6)G361(4)1G5C(1) CC05CG361(4) CCR05CG361(4)(1)(7)

390.0 C05(6)G391(4)1G5C(1) CC05CG391(4) CCR05CG391(4)(1)(7)

430.0 C05(6)G431(4)1G5C(1) CC05CG431(4) CCR05CG431(4)(1)(7)

470.0 C05(6)G471(4)1G5C(1) CC05CG471(4) CCR05CG471(4)(1)(7)

510.0 C05(6)G511(4)1G5C(1) CC05CG511(4) CCR05CG511(4)(1)(7)

560.0 C05(6)G561(4)1G5C(1) CC05CG561(4) CCR05CG561(4)(1)(7)

620.0 C05(6)G621(4)1G5C(1) CC05CG621(4) CCR05CG621(4)(1)(7)

680.0 C05(6)G681(4)1G5C(1) CC05CG681(4) CCR05CG681(4)(1)(7)

750.0 C05(6)G751(4)1G5C(1) CC05CG751(4) CCR05CG751(4)(1)(7)

820.0 C05(6)G821(4)1G5C(1) CC05CG821(4) CCR05CG821(4)(1)(7)

910.0 C05(6)G911(4)1G5C(1) CC05CG911(4) CCR05CG911(4)(1)(7)

1,000.0 C05(6)G102(4)1G5C(1) CC05CG102(4) CCR05CG102(4)(1)(7)

1,100.0 C05(6)G112(4)1G5C(1) CC05CG112(4) CCR05CG112(4)(1)(7)

1,200.0 C05(6)G122(4)1G5C(1) CC05CG122(4) CCR05CG122(4)(1)(7)

1,300.0 C05(6)G132(4)1G5C(1) CC05CG132(4) CCR05CG132(4)(1)(7)

1,500.0 C05(6)G152(4)1G5C(1) CC05CG152(4) CCR05CG152(4)(1)(7)

1,600.0 C05(6)G162(4)1G5C(1) CC05CG162(4) CCR05CG162(4)(1)(7)

1,800.0 C05(6)G182(4)1G5C(1) CC05CG182(4) CCR05CG182(4)(1)(7)

2,000.0 C05(6)G202(4)5G5C(1) CC05CG202(4) CCR05CG202(4)(1)(7)

2,200.0 C05(6)G222(4)5G5C(1) CC05CG222(4) CCR05CG222(4)(1)(7)

2,400.0 C05(6)G242(4)5G5C(1) CC05CG242(4) CCR05CG242(4)(1)(7)

2,700.0 C05(6)G272(4)5G5C(1) CC05CG272(4) CCR05CG272(4)(1)(7)

3,000.0 C05(6)G302(4)5G5C(1) CC05CG302(4) CCR05CG302(4)(1)(7)

3,300.0 C05(6)G332(4)5G5C(1) CC05CG332(4) CCR05CG332(4)(1)(7)

100 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)

50 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)

200 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)

RATINGS & PART NUMBER REFERENCE

To complete Part Number, insert the following letters:

(1) Available FailureRates: A (CC styles only); M, P, R & S (CCR styles only).

(2) Available Capacitance Tolerances: B, C.

(3) Available Capacitance Tolerances: B, C, D.

(4) Available Capacitance Tolerances: F, G, J.

(5) Available Capacitance Tolerances: F, G, J, K.

(6) Insert “2” for standard design, Style C062G Stand-offs are available

Insert “6” for stand-offdesign, Style C066G only as CCR’s, not available as CC.

(7) Add “V” for stand-off design, Style C066G

And leave blank for the flat bottom design (C062G)

(8) Available Capacitance Tolerances: G, J, K

}

MIL-PRF-20

CERAMIC MOLDED/RADIAL — MIL-PRF-20

ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)

CAP.

KEMET

PART NUMBER

MILITARY

STYLE CC

MILITARY STYLE

CCR

360.0 C06(6)G361(4)2G5C(1) CC06CG361(4) CCR06CG361(4)(1)(7)

390.0 C06(6)G391(4)2G5C(1) CC06CG391(4) CCR06CG391(4)(1)(7)

430.0 C06(6)G431(4)2G5C(1) CC06CG431(4) CCR06CG431(4)(1)(7)

470.0 C06(6)G471(4)2G5C(1) CC06CG471(4) CCR06CG471(4)(1)(7)

510.0 C06(6)G511(4)2G5C(1) CC06CG511(4) CCR06CG511(4)(1)(7)

560.0 C06(6)G561(4)2G5C(1) CC06CG561(4) CCR06CG561(4)(1)(7)

620.0 C06(6)G621(4)2G5C(1) CC06CG621(4) CCR06CG621(4)(1)(7)

680.0 C06(6)G681(4)2G5C(1) CC06CG681(4) CCR06CG681(4)(1)(7)

750.0 C06(6)G751(4)2G5C(1) CC06CG751(4) CCR06CG751(4)(1)(7)

820.0 C06(6)G821(4)2G5C(1) CC06CG821(4) CCR06CG821(4)(1)(7)

910.0 C06(6)G911(4)2G5C(1) CC06CG911(4) CCR06CG911(4)(1)(7)

1,000.0 C06(6)G102(4)2G5C(1) CC06CG102(4) CCR06CG102(4)(1)(7)

1,100.0 C06(6)G112(4)2G5C(1) CC06CG112(4) CCR06CG112(4)(1)(7)

1,200.0 C06(6)G122(4)2G5C(1) CC06CG122(4) CCR06CG122(4)(1)(7)

1,300.0 C06(6)G132(4)2G5C(1) CC06CG132(4) CCR06CG132(4)(1)(7)

1,500.0 C06(6)G152(4)2G5C(1) CC06CG152(4) CCR06CG152(4)(1)(7)

1,600.0 C06(6)G162(4)2G5C(1) CC06CG162(4) CCR06CG162(4)(1)(7)

1,800.0 C06(6)G182(4)2G5C(1) CC06CG182(4) CCR06CG182(4)(1)(7)

2,000.0 C06(6)G202(4)1G5C(1) CC06CG202(4) CCR06CG202(4)(1)(7)

2,200.0 C06(6)G222(4)1G5C(1) CC06CG222(4) CCR06CG222(4)(1)(7)

2,400.0 C06(6)G242(4)1G5C(1) CC06CG242(4) CCR06CG242(4)(1)(7)

2,700.0 C06(6)G272(4)1G5C(1) CC06CG272(4) CCR06CG272(4)(1)(7)

3,000.0 C06(6)G302(4)1G5C(1) CC06CG302(4) CCR06CG302(4)(1)(7)

3,300.0 C06(6)G332(4)1G5C(1) CC06CG332(4) CCR06CG332(4)(1)(7)

3,600.0 C06(6)G362(4)1G5C(1) CC06CG362(4) CCR06CG362(4)(1)(7)

3,900.0 C06(6)G392(4)1G5C(1) CC06CG392(4) CCR06CG392(4)(1)(7)

4,300.0 C06(6)G432(4)1G5C(1) CC06CG432(4) CCR06CG432(4)(1)(7)

4,700.0 C06(6)G472(4)1G5C(1) CC06CG472(4) CCR06CG472(4)(1)(7)

5,100.0 C06(6)G512(5)5G5C(1) CC06CG512(5) CCR06CG512(5)(1)(7)

5,600.0 C06(6)G562(5)5G5C(1) CC06CG562(5) CCR06CG562(5)(1)(7)

6,200.0 C06(6)G622(5)5G5C(1) CC06CG622(5) CCR06CG622(5)(1)(7)

6,800.0 C06(6)G682(5)5G5C(1) CC06CG682(5) CCR06CG682(5)(1)(7)

7,500.0 C06(6)G752(5)5G5C(1) CC06CG752(5) CCR06CG752(5)(1)(7)

50 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)

200 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)

100 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)

CAP.

KEMET

PART NUMBER

MILITARY

STYLE CC

MILITARY STYLE

CCR

8,200.0 C06(6)G822(5)5G5C(1) CC06CG822(5) CCR06CG822(5)(1)(7)

9,100.0 C06(6)G912(5)5G5C(1) CC06CG912(5) CCR06CG912(5)(1)(7)

10,000.0 C06(6)G103(5)5G5C(1) CC06CG103(5) CCR06CG103(5)(1)(7)

12,000.0 C06(6)G123(5)5G5C(1) CC06CG123(5) CCR06CG123(5)(1)(7)

15,000.0 C06(6)G153(5)5G5C(1) CC06CG153(5) CCR06CG153(5)(1)(7)

18,000.0 C06(6)G183(5)5G5C(1) CC06CG183(5) CCR06CG183(5)(1)(7)

2,200.0 C512G222(5)2G5C(1) CC07CG222(5) CCR07CG222(5)(1)

2,700.0 C512G272(5)2G5C(1) CC07CG272(5) CCR07CG272(5)(1)

3,300.0 C512G332(5)2G5C(1) CC07CG332(5) CCR07CG332(5)(1)

3,900.0 C512G392(5)2G5C(1) CC07CG392(5) CCR07CG392(5)(1)

4,700.0 C512G472(5)2G5C(1) CC07CG472(5) CCR07CG472(5)(1)

5,600.0 C512G562(5)1G5C(1) CC07CG562(5) CCR07CG562(5)(1)

6,800.0 C512G682(5)1G5C(1) CC07CG682(5) CCR07CG682(5)(1)

8,200.0 C512G822(5)1G5C(1) CC07CG822(5) CCR07CG822(5)(1)

10,000.0 C512G103(5)1G5C(1) CC07CG103(5) CCR07CG103(5)(1)

12,000.0 C512G123(5)1G5C(1) CC07CG123(5) CCR07CG123(5)(1)

15,000.0 C512G153(5)5G5C(1) CC07CG153(5) CCR07CG153(5)(1)

18,000.0 C512G183(5)5G5C(1) CC07CG183(5) CCR07CG183(5)(1)

22,000.0 C512G223(5)5G5C(1) CC07CG223(5) CCR07CG223(5)(1)

27,000.0 C512G273(5)5G5C(1) CC07CG273(5) CCR07CG273(5)(1)

33,000.0 C512G333(5)5G5C(1) CC07CG333(5) CCR07CG333(5)(1)

39,000.0 C512G393(5)5G5C(1) CC07CG393(5) CCR07CG393(5)(1)

47,000.0 C512G473(5)5G5C(1) CC07CG473(5) CCR07CG473(5)(1)

56,000.0 C512G563(5)5G5C(1) CC07CG563(5) CCR07CG563(5)(1)

68,000.0 C512G683(5)5G5C(1) CC07CG683(5) CCR07CG683(5)(1)

83,000.0 C512G833(5)5G5C(1) CC07CG833(5) CCR07CG833(5)(1)

100,000.0 C512G104(5)5G5C(1) CC07CG104(5) CCR07CG104(5)(1)

3,900.0 C522G392(8)2G5C(1) CC08CG392(8) CCR08CG392(8)(1)

4,700.0 C522G472(8)2G5C(1) CC08CG472(8) CCR08CG472(8)(1)

15,000.0 C522G153(8)1G5C(1) CC08CG153(8) CCR08CG153(8)(1)

18,000.0 C522G183(8)1G5C(1) CC08CG183(8) CCR08CG183(8)(1)

56,000.0 C522G563(8)5G5C(1) CC08CG563(8) CCR08CG563(8)(1)

68,000.0 C522G683(8)5G5C(1) CC08CG683(8) CCR08CG683(8)(1)

200 VOLT – C522 SIZE (CC(R)08 PER MIL-PRF-20/38)

100 VOLT – C522 SIZE (CC(R)08 PER MIL-PRF-20/38)

50 VOLT – C522 SIZE (CC(R)08 PER MIL-PRF-20/38)

50 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)

50 VOLT – C512 SIZE (CC(R)07 PER MIL-PRF-20/37)

200 VOLT – C512 SIZE (CC(R)07 PER MIL-PRF-20/37)

100 VOLT – C512 SIZE (CC(R)07 PER MIL-PRF-20/37)

Digitally signed by Marcy Brand

DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corporation, ou=Marketing Communications, cn=Marcy Brand, email=marcybrand@kemet.com

Date: 2013.03.18 12:24:02 -04'00'

CERAMIC LEADED

PACKAGING INFORMATION

Ceramic Axial

Lead Tape and Reel Packaging

KEMET offers standard reeling of Molded and Conformally

Coated Axial Leaded Ceramic Capacitors for automatic insertion

or lead forming machines per EIA specification RS-296. KEMET’s

internal specification four-digit suffix, 7200, is placed at the end of

the part number to designate tape and reel packaging, ie:

C410C104Z5U5CA7200.

Paper (50 lb.) test minimum is inserted between the layers of

capacitors wound on reels for component pitch ≤0.400”.

Capacitor lead length may extend only a maximum of .0625”

(1.59mm) beyond the tapes’ edges. Capacitors are centered in a

row between the two tapes and will deviate only ± 0.031

(0.79mm) from the row center. A minimum of 36” (91.5 cm) leader

tape is provided at each end of the reel capacitors. Universal

splicing clips are used to connect the tape. Standard reel

quantities are shown on page 48.

Tape and Reel Packaging

CERAMIC LEADED

PACKAGING INFORMATION

CERAMIC LEADED

PACKAGING INFORMATION

KEMET

Series

Military

Style

Military

Specification

Standard (1)

Bulk

Quantity

Ammo Pack

Quantity

Maximum

Reel

Quantity

Reel

Size

C114C-K-G CK12, CC75 MIL-C-11015/ 200/Box 5000 12"

C124C-K-G CK13, CC76 MIL-PRF-20 200/Box 5000 12"

C192C-K-G CK14, CC77 100/Box 3000 12"

C202C-K CK15 25/Box 500 12"

C222C-K CK16 10/Tray 300 12"

CK05, CC05 100/Bag 2000 2000 12"

C062C-K-G CK06, CC06 100/Bag 1500 1500 12"

C114G CCR75 MIL-PRF-20 200/Box 5000 12"

C124G CCR76 200/Box 5000 12"

C192G CCR77 100/Box 3000 12"

C202G CC78-CCR78 25/Box 500 12"

C222G CC79-CCR79 10/Tray 300 12"

C052/56G CCR05 100/Bag 1700 12"

C062/66G CCR06 100/Bag 1500 12"

C512G CC07-CCR07 Footnote (2) N/A N/A

C522G CC08-CCR08 Footnote (2) N/A N/A

C114T CKR11 MIL-PRF-39014 200/Box 5000 12"

C124T CKR12 200/Box 5000 12"

C192T CKR14 100/Box 3000 12"

C202T CKR15 25/Box 500 12"

C222T CKR16 10/Tray 300 12"

C052/56T CKR05 100/Bag 1700 12"

C062/66T CKR06 100/Bag 1500 12"

C31X 500/Bag 2500 2500 12"

C32X 500/Bag 2500 2500 12"

C33X 250/Bag 1500 1500 12"

C340 100/Bag 1000 1000 12"

C350 50/Bag N/A 500 12"

C410 300/Box 4000 5000 12"

C412 200/Box 4000 5000 12"

C420 300/Box 4000 5000 12"

C430 200/Box 2000 2500 12"

C440 200/Box 2000 2500 12"

C512 N/A N/A Footnote (2) N/A N/A

C522 N/A N/A Footnote (2) N/A N/A

C617 250/Bag 1000 12"

C622/C623 100/Bag 500 12"

C627/C628 100/Bag 500 12"

C630/C631 100/Bag 500 12"

C637/C638 50/Bag 500 12"

C640/C641 50/Bag 500 12"

C642/C643 50/Bag 500 12"

C647/C648 50/Bag 500 12"

C657/C658 50/Bag 500 12"

C667/C668 50/Bag 500 12"

CERAMIC PACKAGING

NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.

(2) Quantity varies. For further details, please consult the factory.

C052C-K