ZS-2141 - HONEYWELL - Datasheet.Live

C400 2.5-Inch SATA NAND Flash SED SSD

MTFDDAC128MAM-1Jx2, MTFDDAC256MAM-1Kx2,

MTFDDAC512MAM-1Kx2, MTFDDAK128MAM-1Jx2,

MTFDDAK256MAM-1Kx2, MTFDDAK512MAM-1Kx2

Features

• Micron® 25nm MLC NAND Flash

• RoHS-compliant package

• SATA 6 Gb/s interface

• TCG/Opal-compliant self-encrypting drive (SED)

• FIPS-certified, hardware-based AES-256 encryption

engine

• ATA modes supported

– PIO mode 3, 4

– Multiword DMA mode 0, 1, 2

– Ultra DMA mode 0, 1, 2, 3, 4, 5

• Industry-standard, 512-byte sector size support

• Hot-plug capable

• Native command queuing support with 32-com-

mand slot support

• ATA-8 ACS2 command set compliant

• ATA security feature command set and password

• Secure erase (data page) command set: fast and se-

cure erase

• TCG/Opal cryptographic erase, complete and se-

cure in under 4 seconds

• Self-monitoring, analysis, and reporting technology

(SMART) command set

• Performance1, 2

– Sequential 128k READ: up to 500 MB/s

– Sequential 128k WRITE: up to 260 MB/s

– Random 4k READ: up to 45,000 IOPS

– Random 4k WRITE: up to 50,000 IOPS

– PCMark® Vantage (HDD test suite score): up to

75,000

– READ/WRITE latency: 55µs (TYP)

• Reliability

– MTBF: 1.2 million device hours3

– Static and dynamic wear leveling

– Uncorrectable bit error rate (UBER): <1 sector

per 1015 bits read

• Low power consumption

– <280mW TYP4

• Endurance: Total bytes written (TBW) – 72TB

• Capacity5 (unformatted): 128GB, 256GB, 512GB

• Mechanical – 9.5mm height

– SATA connector: 5V ±10%

– 2.5-inch drive: 100.5mm x 69.85mm x 9.5mm

– Weight: 75g (MAX)

• Mechanical – 7.0mm height

– SATA connector: 5V ±10%

– 2.5-inch drive: 100.5mm x 69.85mm x 7.0mm

– Weight: 73g (MAX)

• Field-updateable firmware

• Operating temperature

– Commercial (0°C to +70°C)6

Notes: 1. Typical I/O performance numbers as meas-

ured using Iometer with a queue depth of

32 and write cache enabled.

2. 4K transfers used for READ/WRITE latency

values.

3. The product achieves a mean time between

failure (MTBF) based on population statis-

tics not relevant to individual units.

4. Active power measured during execution of

MobileMark® 2007 with DIPM (device-initi-

ated power management) enabled.

5. 1GB = 1 billion bytes; formatted capacity is

less.

6. Drive case temperature.

Warranty: Contact your Micron sales representative

for further information regarding the product,

including product warranties.

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Features

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Part Numbering Information

Micron’s RealSSD™ C400 SSD is available in different configurations and densities. Visit www.micron.com for a

list of valid part numbers.

Figure 1: Part Number Chart

MT FD D AC xxx M AM - 1 K 1 ES

Micron Technology

Product Family

FD = Flash drive

Drive Interface

D = SATA 6.0 Gb/s

Drive Form Factor

AC = 2.5-inch (9.5mm)

AK = 2.5-inch (7mm)

Drive Density

128 = 128GB

256 = 256GB

512 = 512GB

NAND Flash Type

M = MLC

Product Family

AM = C400

Production Status

Blank = Production

ES = Engineering sample

Operating Temperature Range

Blank = Commercial (0°C to +70°C)

Hardware Feature Set

Blank = Null

AA = Contact factory

AB = Contact factory

AC = Contact factory

Security Feature Set

Blank = Null

2 = Self-encrypting drive

BOM Revision

1 = 1st generation

NAND Flash Component

J = 32Gb, MLC, x8, 3.3V (25nm)

K = 64Gb, MLC, x8, 3.3V (25nm)

Sector Size

1 = 512-byte

x xx

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Features

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.

General Description

Micron’s RealSSD solid state drive (SSD) uses a single-chip controller with a SATA inter-

face on the system side and n-channels of Micron NAND Flash internally. Packaged in

an HDD replacement enclosure, the SSD integrates easily in existing storage infrastruc-

tures.

The SSD is designed to use the SATA interface efficiently during both READs and

WRITEs while delivering bandwidth-focused performance. SSD technology enables en-

hanced boot times, faster application load times, reduced power consumption, and ex-

tended reliability.

The RealSSD self-encypting drive (SED) features a FIPS-compliant AES-256 encryption

engine, providing hardware-based, secure data encryption, with no loss of SSD per-

formance. This SED follows the TCG/Opal specification for trusted peripherals.

Figure 2: Functional Block Diagram

NAND

SATA

NAND

SSD

controller

DRAM

buffer

NAND

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

General Description

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.

Logical Block Address Configuration

The drive is set to report the number of logical block addresses (LBA) that will ensure

sufficient storage space for the specified density. Standard LBA settings, based on the

IDEMA standard (LBA1-02), are shown below.

Table 1: Standard LBA Settings

Drive Size

Total LBA Max LBA

User Available

Bytes

Decimal Hexadecimal Decimal Hexadecimal (Unformatted)

128GB 250,069,680 EE7C2B0 250,069,679 EE7C2AF 128,035,676,160

256GB 500,118,192 1DCF32B0 500,118,191 1DCF32AF 256,186,209,271

512GB 1,000,215,216 3B9E12B0 1,000,215,215 3B9E12AF 512,110,190,592

Physical Configuration

Table 2: 2.5-Inch Dimensions and Weight

Value

UnitHeight: 9.5mm Height: 7mm

Width 69.85 69.85 mm (NOM)

Length 100.50 100.50 mm (NOM)

Unit weight 75 73 g (MAX)

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Logical Block Address Configuration

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.

Interface Connectors

The SATA signal segment interface cable has four conductors and three ground connec-

tions. As shown in Package Dimensions, the cable includes a 7-pin signal segment and a

15-pin power segment arranged in a single row with a 1.27mm (0.050in) pitch.

Table 3: SATA Signal Segment Pin Assignments

Signal Name Type Description

S1 GND Ground

S2 A Differential signal pair A and A#

S3 A#

S4 GND Ground

S5 B# Differential signal pair B and B#

S6 B

S7 GND Ground

Table 4: 2.5-Inch SATA Power Segment Pin Assignments

Pin# Signal Name Description

P1 V33 No connect

P2 V33 No connect

P3 V33 No connect

P4 GND Ground

P5 GND Ground

P6 GND Ground

P7 V5 5V power, precharge

P8 V5 5V power

P9 V5 5V power

P10 GND Ground

P11 DAS Device activity signal

P12 GND Ground

P13 V12 No connect

P14 V12 No connect

P15 V12 No connect

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Interface Connectors

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 3: SSD Interface Connections

Power

segment

P1 S1

Signal

segment

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Interface Connectors

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.

Performance

Measured performance can vary for a number of reasons. The major factors affecting

drive performance are the density of the drive and the interface of the host. Additional-

ly, overall system performance can affect the measured drive performance. When com-

paring drives, it is recommended that all system variables are the same, and only the

drive being tested varies.

Performance numbers will vary depending on the host system configuration.

Table 5: Drive Performance

Density 128GB 256GB 512GB

UnitInterface Speed 6 Gb/s 6 Gb/s 6 Gb/s

Sequential read (128k transfer) 500 500 500 MB/s

Sequential write (128k transfer) 175 260 260 MB/s

Random read (4k transfer) 45K 45K 45K IOPs

Random write (4k transfer) 35K 50K 50K IOPs

Read latency 55 55 55 µs

Write latency 55 55 55 µs

PCMark vantage 65K 75K 75K HDD score

Notes: 1. Typical I/O performance numbers as measured using IOMeter with a queue depth of 32

and write cache enabled.

2. IOMeter measurements are performed on an 8GB span.

3. 4k transfers used for READ/WRITE latency values.

4. System variations may affect measured results.

5. Performance numbers are indicative of C400 firmware version 0009 and newer.

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Performance

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.

Reliability

Micron’s SSDs incorporate advanced technology for defect and error management.

They use various combinations of hardware-based error correction algorithms and

firmware-based static and dynamic wear-leveling algorithms.

Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is de-

fined as data that is reported as successfully programmed to the SSD but when it is read

out of the SSD, the data differs from what was programmed.

Table 6: Uncorrectable Bit Error Rate

Uncorrectable Bit Error Rate Operation

<1 sector per 1015 bits read READ

Mean Time To Failure

Mean time to failure (MTTF) for the SSD can be predicted based on the component reli-

ability data using the methods referenced in the Telcordia SR-332 reliability prediction

procedures for electronic equipment.

Table 7: MTTF

Density MTTF (Operating Hours)1

128GB 1.2 million

256GB 1.2 million

512GB 1.2 million

Note: 1. The product achieves a mean time to failure (MTTF) of 1.2 million hours, based on popu-

lation statistics not relevant to individual units.

Endurance

Endurance for the SSD can be predicted based on the usage conditions applied to the

device, the internal NAND component cycles, the write amplification factor, and the

wear-leveling efficiency of the drive. The table below shows the drive lifetime for each

SSD density based on predefined usage conditions.

Table 8: Drive Lifetime

Density Drive Lifetime (Total Bytes Written)

128GB 72TB

256GB 72TB

512GB 72TB

Notes: 1. Total bytes written calculated with the drive 90% full.

2. Access patterns are 50% sequential and 50% random and consist of the following: 5%

are 4k; 5% are 8k; 10% are 16k; 10% are 32k; 35% are 64K; and 35% are 128k.

3. GB/day can be calculated by dividing the total bytes written value by (365 × number of

years). For example: 72TB/5 years/365 days = 40 GB/day for 5 years.

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Reliability

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.

Electrical Characteristics

Stresses greater than those listed may cause permanent damage to the device. This is a

stress rating only, and functional operation of the device at these or any other condi-

tions above those indicated in the operational sections of this specification is not im-

plied. Exposure to absolute maximum rating conditions for extended periods may affect

reliability.

Table 9: SATA Power Consumption

Density Idle Average Active Average

Sequential Write/Read Maximum

(128k transfer) Unit

128GB <85 150 3500 2000 mW

256GB <85 160 4000 2200 mW

512GB <100 280 5500 2500 mW

Notes: 1. Data taken at 25°C using a 6 Gb/s SATA interface.

2. Active average power measured while running MobileMark® 2007 Productivity Suite.

3. DIPM (device-initiated power management) enabled.

4. Sequential power measured in IOMETER MAX with 128KB transfer size.

Table 10: Maximum Ratings

Parameter/Condition Symbol Min Max Unit

Voltage input V5 4.5 5.5 V

Operating temperature TC0 70 °C

Non-operating temperature –40 85 °C

Rate of temperature change – 20 °C/hour

Relative humidity (non-condensing) 5 95 %

Note: 1. Temperature is best measured with a thermocouple attached to the center point of the

exterior of the case on the cast side (side where the SATA connector is visible). Contact

with the drive label is acceptable.

Table 11: Shock and Vibration

Parameter/Condition Specification

Operating shock 1500 G/1.0ms

Operating vibration 2–500Hz at 3.1G

Table 12: TCG/Opal Support Parameters

TCG Property Requirement

Min

Requirement

in TCG/Opal

Micron C400

Implementa-

tion Remarks

COM ID manage-

ment support

Vendor

decision

Not supported Dynamic COM ID allocation and management

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Electrical Characteristics

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 12: TCG/Opal Support Parameters (Continued)

TCG Property Requirement

Min

Requirement

in TCG/Opal

Micron C400

Implementa-

tion Remarks

Base COM ID Vendor

decision

0x1000 0x1000-0xFFFF defined for COM ID management

Number of COM IDs 1 1

Buffer management

support

Vendor

decision

No Flow control

ACK/NACK support Vendor

decision

No Session reliability

Async support Vendor

decision

No Asynchronous protocol support with multiple

commands per session

Range crossing Vendor

decision

0 If the drive receives a READ or WRITE command

that spans multiple LBA ranges and the LBA

ranges are not locked then:

1. Process the data transfer if range crossing = 0

2. Terminate the command with "Other Invalid

Command Parameter" if range crossing = 1

Protocol stack reset Optional Yes

MaxComPacketSize 2048 16,384 Host value accepted is VU for maximum

MaxResponseCom-

PacketSize

2048 16,384

MaxPacketSize 2028 16,064 Host value accepted is VU for maximum

MaxIndTokenSize 1992 15,488 Host value accepted is VU for maximum

MaxPackets 1 1 Host value accepted is VU for maximum

MaxSubPackets 1 1 Host value accepted is VU for maximum

MaxSessions 1 1 Each session requires a set of buffers and varia-

bles

MaxTransactionLimit 1 1 Transaction are inside sessions

MaxMethods 1 1 Methods are contained in a transaction

MaxAuthentications 2 2

DefSessionTimeout Vendor

decision

Yes

Close session Optional Yes Enables the trusted device to notify the host

that it has aborted a session

Interface control

template (restricted

commands table)

Optional No The interface control template enables trusted

device control over selected interface com-

mands. The benefit is the reduction of unde-

sired side effects.

Type table Not required No

AES key size 128/256 bits 256 bits AES key is generated by using the CTR DRBG al-

gorithm (FIPS-compliant)

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Electrical Characteristics

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 12: TCG/Opal Support Parameters (Continued)

TCG Property Requirement

Min

Requirement

in TCG/Opal

Micron C400

Implementa-

tion Remarks

# LBA ranges 4 16 Supports up to 16 LBA ranges and the same AES

key is used for all ranges. Cross-range READ and

WRITE operations are supported if LBA ranges

are unlocked.

# Admins 1 16

# Users 4 16

MBR table 128MB 128MB

Datastore table 1KB 10MB

Re-encryption No

Secure firmware

download

Secure firmware download feature is optional.

The firmware image is validated by using the

SHA256 and RSA2048 alogrithms (FIPS-compli-

ant)

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Electrical Characteristics

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Device ID

Table 13: Identity Device

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

0 General configuration bit-significant information

15 F 0b 0 = ATA device

14–8 X 0000100b Retired

7 F 0b 1 = removable media device

6 F 1b Obsolete

5–3 X 000b Retired

2 V 0b Response incomplete

1 X 0b Retired

0 F 0b Reserved

1 3FFFh Obsolete

2 F C837h Specific configuration

3 F 0010h Obsolete

4 F 0000h 0000h Retired

6 F 003Fh Obsolete

7 (O)V 0000h 0000h Reserved for assignment by the CompactFlash™ Association

9 ( )X 0000h Retired

10 (M)F varies Serial number (20 ASCII characters)

20 ( )X 0000h 0000h

0000h

Retired/Obsolete

23 (M)F varies Firmware revision (8 ASCII characters)

27 (M)F varies Model number (40 ASCII characters)

47 15–8 F 80h 80h

7–0 F 10h 00h = Reserved

01h-FFh = Maximum number of logical sectors that shall be

transferred per DRQ data block on READ/WRITE MULTIPLE

commands

48 Trusted Computing feature set options

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13–1 F 0000000000000b Reserved for the Trusted Computing Group

0 F 1b 1=Trusted Computing feature set is support

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

49 Capabilities

15–14 F 00b Reserved for the IDENTIFY PACKET DEVICE command.

13 F 1b 1 = Standby timer values as specified in this standard are

supported

0 = Standby timer values shall be managed by the device

12 F 0b Reserved for the IDENTIFY PACKET DEVICE command.

11 F 1b 1= IORDY supported

0 = IORDY may be supported

10 F 1b 1 = IORDY may be disabled

9 1b 1 = LBA supported

8 F 1b 1 = DMA supported.

7–0 F 00000000b Retired

50 Capabilities

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13–2 F 000000000000b Reserved

1 X 0b Obsolete

0 F 1b Shall be set to one to indicate a vendor specific standby tim-

er value minimum.

51 ( )X 0000h 0000h Obsolete

53 15–3 F 0000000000000b Reserved

2 F 1b 1 = the fields reported in word 88 are valid

0 = the fields reported in word 88 are not valid

1 F 1b 1 = the fields reported in words (70:64) are valid

0 = the fields reported in words (70:64) are not valid

0 X 1b Obsolete

54 ()X 3FFFh 0010h

003Fh FC10h

00FBh

Obsolete

59 15 F 0b 1 = The BLOCK ERASE EXT command is supported

14 F 0b 1 = The OVERWRITE EXT command is supported

13 F 0b 1 = The CRYPTO SCRAMBLE EXT command is supported

12 F 0b 1 = The Sanitize feature set is supported

11–9 F 000b Reserved

8 V 1b 1 = Multiple sector setting is valid

7–0 V 00000001b xxh = Current setting for number of logical sectors that shall

be transferred per DRQ data block on READ/WRITE MULTI-

PLE commands

60 M(F) Varies by capacity Total number of user addressable logical sectors

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

62 ()X 0000h Obsolete

63 15–11 F 00000b Reserved

10 V 0b 1 = Multiword DMA mode 2 is selected

0 = Multiword DMA mode 2 is not selected

9 V 0b 1 = Multiword DMA mode 1 is selected

0 = Multiword DMA mode 1 is not selected

8 V 0b 1 = Multiword DMA mode 0 is selected

0 = Multiword DMA mode 0 is not selected

7–3 F 0000b Reserved

2 F 1b 1 = Multiword DMA mode 2 and below are supported

1 F 1b 1 = Multiword DMA mode 1 and below are supported

0 F 1b 1 = Multiword DMA mode 0 is supported

64 15–8 F 0 Reserved

7–0 F 03h PIO modes supported

65 F 0078h Minimum Multiword DMA transfer cycle time per word

Cycle time in nanoseconds

66 F 0078h Manufacturer's recommended Multiword DMA transfer cy-

cle time

Cycle time in nanoseconds

67 F 0078h Minimum PIO transfer cycle time without flow control

Cycle time in nanoseconds

68 F 0078h Minimum PIO transfer cycle time with IORDY flow control

Cycle time in nanoseconds

69 F Additional Supported

15 F 0b 1 = CFast Specification Support

14 F 1b 1 = Deterministic read after Trim is supported

13 F 0b 1 = Long Physical Sector Alignment Error Reporting Control

is supported

12 F 0b 1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE

CONFIGURATION SET DMA are supported

11 F 0b 1 = READ BUFFER DMA is supported

10 F 0b 1 = WRITE BUFFER DMA is supported

9 F 0b 1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA

are supported

8 F 0b 1 = DOWNLOAD MICROCODE DMA is supported

7 F 0b Reserved for IEEE-1667

6 F 0b 1 = Optional ATA device 28-bit commands supported

5 F 0b 1 = Read zero after Trim is supported

4–0 F 00000b Reserved

70 F 0000h Reserved

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

71 F 0000h 0000h

0000h 0000h

Reserved for the IDENTIFY PACKET DEVICE command

75 Queue depth

15–5 F 00000000000b Reserved

4–0 F 11111b Maximum queue depth - 1

76 Serial ATA Capabilities

15–13 F 000b Reserved

12 F 1b Supports Native Command Queuing priority information

11 F 0b Supports Unload while NCQ commands outstanding

10 F 1b Supports Phy event counters

9 F 1b Supports receipt of host initiated interface power manage-

ment requests

8 F 1b Supports native Command Queueing

7–4 F 0000b Reserved for future Serial ATA signaling speed grades

3 F 1b 1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s)

2 F 1b 1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s)

1 F 1b 1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s)

0 F 0b Reserved (set to 0)

77 Serial ATA Additional capabilities

15–6 F 0000000000b Reserved for future Serial ATA definition

5 F 0b Supports NCQ Queue Management Command

4 F 0b Supports NCQ Streaming

3–1 V 010b Coded value indicating current negotiated Serial ATA signal

speed

0 F 0b Shall be cleared to zero

78 Serial ATA features Supported

15–7 F 000000000b Reserved

6 F 1b 1 = supports software settings preservation

5 F 0b Reserved

4 F 0b 1 = supports in-order data delivery

3 F 1b 1 = supports dev initiate interface power management

2 F 1b 1 = supports DMA Setup Auto-Activate optimization

1 F 0b 1 = supports non-zero buffer offsets in DMA Setup FIS

0 F 0b Reserved (set to 0)

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

79 Serial ATA features Enabled

15–7 V 000000000b Reserved

6 V 1b 1 = software settings preservation enabled

5 V 0b 1 = Asynchronous notification enabled

4 V 0b 1 = in-order data delivery enabled

3 V 0b 1 = device initiating interface power management enabled

2 V 0b 1 = DMA Setup Auto-Activate optimization enabled

1 V 0b 1 = non-zero buffer offsets in DMA Setup FIS enabled

0 V 0b Reserved (set to 0)

80 Major revision number

15–10 F 000000b Reserved

9 F 1b 1 = supports ATA8-ACS2

8 F 1b 1 = supports ATA8-ACS

7 F 1b 1 = supports ATA/ATAPI-7

6 F 1b 1 = supports ATA/ATAPI-6

5 F 1b 1 = supports ATA/ATAPI-5

4 F 1b 1 = supports ATA/ATAPI-4

3 F 1b Obsolete

2 S 0b Obsolete

1 S 0b Obsolete

0 F 0b Reserved

81 F 0028h Minor revision number

0028h = ATA8-ACS version 6

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

82 Command set supported

15 X 0b Obsolete

14 F 1b 1 = NOP command supported

13 F 1b 1 = READ BUFFER command supported

12 F 1b 1 = WRITE BUFFER command supported

11 X 0b Obsolete

10 F 1b 1 = Host Protected Area feature set supported

9 F 0b 1 = DEVICE RESET command supported

8 F 0b 1 = SERVICE interrupt supported

7 F 0b 1 = release interrupt supported

6 F 1b 1 = read look-ahead supported

5 F 1b 1 = write cache supported

4 F 0b Shall be cleared to zero to indicate that the PACKET feature

set is not supported.

3 F 1b 1 = mandatory Power Management feature set supported

2 F 0b Obsolete

1 F 1b 1 = Security feature set supported

0 F 1b 1 = SMART feature set supported

83 Command set supported

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13 F 1b 1 = FLUSH CACHE EXT command supported

12 F 1b 1 = mandatory FLUSH CACHE command supported

11 F 1b 1 = Device Configuration Overlay feature set supported

10 F 1b 1 = 48-bit Address feature set supported

9 F 0b 1 = Automatic Acoustic Management feature set supported

8 F 1b 1 = SET MAX security extension supported

7 F 0b See Address Offset Reserved Area Boot INCITS TR27:2001

6 F 0b 1 = SET FEATURES subcommand required to spin-up after

power-up

5 F 0b 1 = Power-Up In Standby feature set supported

4 F 0b Obsolete

3 F 1b 1 = Advanced Power Management feature set supported

2 F 0b 1 = CFA feature set supported

1 F 0b 1 = READ/WRITE DMA QUEUED supported

0 F 1b 1 = DOWNLOAD MICROCODE command supported

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

84 Command set/feature supported extension

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported

12 F 0b Reserved for technical report INCITS TR-37-2004 (TLC)

11 F 0b Reserved for technical report INCITS TR-37-2004 (TLC)

10–9 F 00b Obsolete

8 F 1b 1 = 64-bit Word wide name supported

7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported

6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT

commands supported

5 F 1b 1 = General Purpose Logging feature set supported

4 F 0b 1 = Streaming feature set supported

3 F 0b 1 = Media Card Pass Through Command feature set suppor-

ted

2 F 0b 1 = Media serial number supported

1 F 1b 1 = SMART self-test supported

0 F 1b 1 = SMART error logging supported

85 Command set/feature enabled.

15 X 0b Obsolete

14 F 1b 1 = NOP command supported

13 F 1b 1 = READ BUFFER command supported

12 F 1b 1 = WRITE BUFFER command supported

11 X 0b Obsolete

10 V 1b 1 = Host Protected Area feature set enabled

9 F 0b 1 = DEVICE RESET command supported

8 V 0b 1 = SERVICE interrupt enabled

7 V 0b 1 = release interrupt enabled

6 V 1b 1 = look-ahead enabled

5 V 1b 1 = write cache enabled

4 F 0b Shall be cleared to zero to indicate that the PACKET feature

set is not supported.

3 F 1b Power Management feature set is enabled

2 F 0b Obsolete

1 V 0b 1 = Security Mode feature set enabled

0 V 1b 1 = SMART feature set enabled

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

86 Command set/feature enabled.

15 1b 1 = Words 120-119 are valid

14 F 0b 1 = Reserved

13 F 1b 1 = FLUSH CACHE EXT command supported

12 F 1b 1 = FLUSH CACHE command supported

11 F 1b 1 = Device Configuration Overlay supported

10 F 1b 1 = 48-bit Address features set supported

9 V 0b 1 = Automatic Acoustic Management feature set enabled

8 F 0b 1 = SET MAX security enabled by SET MAX SET PASSWORD

7 F 0b Reserved for address Offset Reserved Area Boot, INCITS

TR27:2001

6 F 0b 1 = SET FEATURES subcommand required to spin-up after

power-up

5 V 0b 1 = Power-Up In Standby feature set enabled

4 V 0b Obsolete

3 V 1b 1 = Advanced Power Management feature set enabled

2 F 0b 1 = CFA feature set supported

1 F 0b 1 = READ/WRITE DMA QUEUED command supported

0 F 1b 1 = DOWNLOAD MICROCODE command supported

87 Command set/feature enabled/supported

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported

12 V 0b Reserved for technical report- INCITS tr-37-2004 (TLC)

11 V 0b Reserved for technical report- INCITS TR-37-2004 (TLC)

10–9 F 00b Obsolete

8 F 1b 1 = 64-bit Word wide name supported

7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported

6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT

commands supported

5 F 1b 1 = General Purpose Logging feature set supported

4 V 0b Obsolete

3 V 0b 1 = Media Card Pass Through Command feature set suppor-

ted

2 V 0b 1 = Media serial number is valid

1 F 1b 1 = SMART self-test supported

0 F 1b 1 = SMART error logging supported

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

88 0b Ultra DMA modes

15 0b Reserved

14 0b 1 = Ultra DMA mode 6 is selected

0 = Ultra DMA mode 6 is not selected

13 0b 1 = Ultra DMA mode 5 is selected

0 = Ultra DMA mode 5 is not selected

12 0b 1 = Ultra DMA mode 4 is selected

0 = Ultra DMA mode 4 is not selected

11 0b 1 = Ultra DMA mode 3 is selected

0 = Ultra DMA mode 3 is not selected

10 0b 1 = Ultra DMA mode 2 is selected

0 = Ultra DMA mode 2 is not selected

9 0b 1 = Ultra DMA mode 1 is selected

0 = Ultra DMA mode 1 is not selected

8 0b 1 = Ultra DMA mode 0 is selected

0 = Ultra DMA mode 0 is not selected

7 0b Reserved

6 0b 1 = Ultra DMA mode 6 and below are supported

5 1b 1 = Ultra DMA mode 5 and below are supported

4 1b 1 = Ultra DMA mode 4 and below are supported

3 1b 1 = Ultra DMA mode 3 and below are supported

2 1b 1 = Ultra DMA mode 2 and below are supported

1 1b 1 = Ultra DMA mode 1 and below are supported

0 1b 1 = Ultra DMA mode 0 IS supported

89 (O)F 0001h Time required for security erase unit completion

90 (O)F 0001h Time required for Enhanced security erase completion

91 (O)V 00FEh Current advanced power management value

92 (O)V FFFEh Master Password Revision Code

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

93 Shall be 0000h for SATA devices

15 0b Shall be cleared to zero

14 0b Shall be set to one

13 0b 1 = device detected CBLID-above VIH

0 = device detected CBLID-below VIL

Device 1 hardware reset result

Device 0 shall clear these bits to zero

Device 1 shall set these bits as follows:

12 0b Reserved

11 0b 0 = Device 1 did not assert PDIAG-

1 = Device 1 asserted PDIAG-

10–9 These bits indicate how Device 1 determined the device

number:

00 = Reserved

01 = a jumper was used

10 = the CSEL signal was used

11 = some other method was used or the method is un-

known

8 0b Shall be set to one

Device 0 hardware reset result. Device 1 shall clear these

bits to zero.

Device 0 shall set these bits as follows:

7 0b Reserved

6 0b 0 = Device 0 does not respond when Device 1 is selected.

1 = Device 0 responds when Device 1 is selected.

5 0b 0 = Device 0 did not detect the assertion of DASP-

1 = Device 0 detected the assertion of DASP-

4 0b 0 = Device 0 did not detect the assertion of PDIAG-

1 = Device 0 detected the assertion of PDIAG-

3 0b 0 = Device 0 failed diagnostics.

1 = Device 0 passed diagnostics.

2–1 00b These bits indicate how Device 0 determined the device

number:

00 = Reserved

01 = a jumper was used

10 = the CSEL signal was used

11 = some other method was used or the method is un-

known

0 0b Shall be set to one

94 15–8 F 00h Vendor's recommended acoustic management value

7–0 V 00h Current automatic acoustic management value

95 (O)V 0000h Stream Minimum Request Size

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

96 (O)V 0000h Streaming Transfer Time - DMA

97 (O)V 0000h Streaming Access Latency - DMA and PIO

98 (O)F 0000h 0000h Streaming Performance Granularity(98-99)

100 V Varies by capacity Maximum user LBA for 48-bit Address feature set

104 (O)V 0000h Streaming Transfer Time - PIO

105 ( )F 0008h Maximum number of 512-byte blocks of LBA Range Entries

per DATA SET MANAGEMENT command

106 Physical sector size / Logical Sector Size

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13 F 0b 1 = Device has multiple logical sectors per physical sector

12 F 0b 1 = Device Logical Sector Longer than 256 Words

11–4 F 00000000b Reserved

3–0 F 0000b 2^x logical sectors per physical sector

107 (O)F 0000h Inter-seek delay for ISO-7779 acoustic testing in microsec-

onds

108 15–12 F 0101b NAA (3-0)

11–0 000000001010b IEEE OUI (23-12)

109 15–4 F 000001110101b IEEE OUI (11-0)

3–0 Varies Unique ID (35-32)

110 (M)F Varies 5-0 Unique ID (31-16)

111 (M)F Varies Unique ID (15-0)

112 (O)F 0000h 0000h

0000h 0000h

Reserved for 128 bit world wide name extension to 128 bits

116 (O)V 0000h Reserved for INCITS TR-37-2004

117 (O)F 0000h 0000h Words per Logical Sector

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

119 Commands and feature sets supported (Continued from

words 84-82)

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13–6 F 00000001b Reserved

5 F 0b 1 = Free-fall Control feature set is supported

4 F 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is

supported

3 F 1b 1 = READ LOG DMA EXT and WRITE LOG DMA EXT com-

mands are supported

2 F 1b 1 = The Write-Read-Verify feature set is supported

1 F 1b 1 = Feature set "Disable Data Transfer After Error Detec-

tion" is supported

0 F 0b Reserved for DDT

120 Commands and feature sets supported or enabled (Contin-

ued from words 87-85)

15 0b Shall be cleared to zero

14 1b Shall be set to one

13–6 00000000b Reserved

5 0b 1 = Free-fall Control feature set is enabled

4 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is

supported

3 1b 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT

commands are supported

2 1b 1 = The WRITE UNCORRECTABLE EXT command is supported

1 0b 1 = The Write-Read-Verify feature set is enabled

0 0b 1= Feature set "Disable Data Transfer After Error Detection"

is enabled

0 = Feature set "Disable Data Transfer After Error Detec-

tion" is disabled

121 F 0000h 0000h

0000h 0000h

Reserved for expanded supported and enabled settings

127 (O) 0000h Obsolete

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

128 Security status

15–9 F 0000000b Reserved

8 V 0b Security level 0 = High, 1 = Maximum

7–6 F 00b Reserved

5 F 1b 1 = Enhanced security erase supported

4 V 0b 1 = Security count expired

3 V 0b 1 = Security frozen

2 V 0b 1 = Security locked

1 V 0b 1 = Security enabled

0 F 1b 1 = Security supported

129 ( )X Vendor specific

data

Vendor specific

160 CFA power mode 1

15 F 0b Word 160 supported

14 F 0b Reserved

13 F 0b CFA power mode 1 is required for one or more commands

implemented by the device

12 V 0b CFA power mode 1 disabled

11–0 F 000000000000b Maximum current in ma

161 X 0000h 0000h

0000h 0000h

0000h

Reserved for assignment by the CompactFlash Association

168 15–4 F 000h Reserved

3-0 F 3h Device Nominal Form Factor

169 DATA SET MANAGEMENT command support

15–1 F 000000000000000

Reserved

0 F 1b 1 = the Trim bit in the DATA SET MANAGEMENT command

is supported

170 F 0000h 0000h

0000h 0000h

Additional Product Identifier

174 F 0000h 0000h Reserved

176 (O)V Varies Current media serial number (60 ASCII characters)

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

206 SCT Command Transport

15–12 X 0000b Vendor Specific

11–6 F 000000b Reserved

5 F 1b SCT Command Transport Data Tables supported

4 F 1b CT Command Transport Features Control supported

3 F 1b SCT Command Transport Error Recovery Control supported

2 F 1b SCT Command Transport Write Same supported

1 F 0b SCT Command Transport Long Sector Access supported

0 F 1b SCT Command Transport supported

207 ( )F 0000h 0000h Reserved for CE-ATA

209 (O) Alignment of logical blocks within a larger physical block

15 F 0b Shall be cleared to zero

14 F 1b Shall be set to one

13–0 F 00000000000000b 'Logical sector' offset within the first physical sector where

the first logical

sector is placed.

210 (O)V 0000h 0000h Write-Read-Verify Sector Count Mode 3 Only

212 (O)F 0000h 0001h Verify Sector Count Mode 2 Only

214 (O) NV Cache Capabilities

15–12 F 0000b NV Cache feature set version

11–8 F 0000b NV Cache Power Mode feature set version

7–5 F 000b Reserved

4 V 0b 1 = NV Cache feature set enabled

3–2 F 00b Reserved

1 V 0b 1 = NV Cache Power Mode feature set enabled

0 F 0b 1 = NV Cache Power Mode feature set supported

215 (O)V 0000h NV Cache Size in Logical Blocks (LSW)

216 (O)V 0000h NV Cache Size in Logical Blocks (MSW)

217 (M)F 0001h Nominal media rotation rate (ATA8-ACS 1699-D Revision 6)

NV Cache Read Transfer Speed in MB/s (ATA8-ACS 1699-D

Revision 3f)

218 (O)V 0000h NV Cache Write Transfer Speed in MB/s

219 NV Cache Options

15–8 F 00h Reserved

7–0 F 00h Device Estimated Time to Spin Up in Seconds

220 15–8 F 00h Reserved

7–0 V 00h Write-Read-Verify feature set current mode

221 0000h Reserved

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 13: Identity Device (Continued)

See Note 1 for setting definitions

Word Bit(s) Setting Default Value Description

222 Transport Major revision number. 0000h or FFFFh = device

does not report version

15–12 0001b Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved

Parallel (Type = 0) Serial (Type = 1)

11–6 000000b Reserved Reserved

5 1b Reserved SATA Rev 3.0

4 1b Reserved SATA Rev 2.6

3 1b Reserved SATA Rev 2.5

2 1b Reserved SATA II: Extensions

1 1b Reserved SATA 1.0a

0 1b ATA8-APT ATA8-AST

223 (M)F 0000h Transport Minor revision number

224 ( )F 0000h 0000h

0000h 0000h

Reserved for CE-ATA

234 (O)F 0001h Minimum number of 512 byte units per DOWNLOAD MI-

CROCODE command for mode 3

235 00FFh Maximum number of 512 byte units per DOWNLOAD MI-

CROCODE command for mode 3

236 0000h 0000h

0000h 0000h

0000h

Reserved

255 (M)F Integrity word

15–8 varies Checksum

7–0 A5h Signature

Note: 1. F = The content of the word is fixed and does not change.

V = The content of the word is variable and may change depending on the state of the

device or the commands executed by the device.

X = The content of the word may be fixed or variable.

R = The content of the word is reserved and will be zero.

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Device ID

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Commands

Table 14: Supported ATA Command Set

See ATA-8 standard for command details

Command Name Command Code (hex)

CHECK POWER MODE 98h or E5h

DEVICE CONFIGURATION RESTORE B1h/C1h

DEVICE CONFIGURATION FREEZE LOCK B1h/C3h

DEVICE CONFIGURATION IDENTIFY B1h/C1h

DEVICE CONFIGURATION SET B1h/C3h

DOWNLOAD MICROCODE 92h

EXECUTE DEVICE DIAGNOSTIC 90h

FLUSH CACHE E7h

FLUSH CACHE EXT EAh

IDENTIFY DEVICE ECh

IDLE E3h or 97h

IDLE IMMEDIATE E1h or 95h

INITIALIZE DEVICE PARAMETERS 91h

NOP 00h

READ BUFFER E4h

READ DMA (with retry) C8h

READ DMA (without retry) C9h

READ DMA EXT 25h

READ FPDMA QUEUED 60h

READ LOG EXT 2Fh

READ MULTIPLE C4h

READ MULTIPLE EXT 29h

READ NATIVE MAX ADDRESS F8h

READ NATIVE MAX ADDRESS EXT 27h

READ SECTOR(S) EXT 24h

READ SECTOR(S) (with retry) 20h

READ SECTOR(S) (without retry) 21h

READ VERIFY SECTOR EXT 42h

READ VERIFY SECTOR(S) (with retry) 40h

SCT WRITE SAME 02h/0001h

02h/0002h

02h/0101h

02h/0102h

SCT RETURN ERROR RECOVERY CONTROL 030h/01h

SCT SET ERROR RECOVERY CONTROL 03h/01h

SCT SET FEATURE CONTROL 04h/01h

SCT RETURN FEATURE CONTROL 04h/02h

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Commands

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 14: Supported ATA Command Set (Continued)

See ATA-8 standard for command details

Command Name Command Code (hex)

SCT RETURN FEATURE OPTION FLAG 04h/03h

SCT RETURN SCT DATA TABLE 05h/01h

SECURITY DISABLE PASSWORD F6h

SECURITY ERASE PREPARE F3h

SECURITY ERASE UNIT F4h

SECURITY FREEZE LOCK F5h

SECURITY SET PASSWORD F1h

SECURITY UNLOCK F2h

SEEK 7xh

SET FEATURES EFh

SET MAX ADDRESS F9h

SET MAX – FREEZE LOCK F9h/04h

SET MAX – LOCK F9h/02h

SET MAX ADDRESS EXT 37h

SET MULTIPLE MODE C6h

SET MAX – SET PASSWORD F9h/01h

SET MAX – UNLOCK F9h/03h

SLEEP E6h or 99h

SMART DISABLE OPERATIONS B0h/D9h

SMART ENABLE OPERATIONS B0h/D8h

SMART ENABLE/DISABLE AUTOSAVE B0h/D2h

SMART EXECUTE OFF-LINE IMMEDIATE B0h/D4h

SMART READ DATA B0h/D0h

SMART READ LOG SECTOR B0h/D5h

SMART RETURN STATUS B0h/DAh

SMART WRITE LOG B0h/D6h

STANDBY E2h or 96h

STANDBY IMMEDIATE E0h or 94h

TRUSTED NON-DATA 5Bh

TRUSTED RECEIVE 5Ch

TRUSTED RECEIVE DMA 5Dh

TRUSTED SEND 5Eh

TRUSTED SEND DMA 5Fh

WRITE BUFFER E8h

WRITE DMA (with retry) CAh

WRITE DMA (without retry) CBh

WRITE DMA EXT 35h

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Commands

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 14: Supported ATA Command Set (Continued)

See ATA-8 standard for command details

Command Name Command Code (hex)

WRITE DMA FUA EXT 3Dh

WRITE FPDMA QUEUED 61h

WRITE LOG EXT 3Fh

WRITE MULTIPLE C5h

WRITE MULTIPLE EXT 39h

WRITE MULTIPLE FUA EXT CEh

WRITE SECTOR(S) (with retry) 30h

WRITE SECTOR(S) EXT 34h

WRITE UNCORRECTABLE EXT 45h

Compliance

Micron self-encrypting SSDs comply with the following:

• RoHS “green”

• CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003

• FCC: CFR Title 47, Part 15, ICES-003, all Class B

• UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Ed-

ition

• BSMI (Taiwan): approval to CNS 13438

• C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22

• KCC RRL (Korea): approval to KCC MU2-C30025, KCC MU2-C30018 Class B

• W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations

may apply to customers who place these products in the markets where WEEE is en-

forced.

• TUV (Germany): approval to IEC60950/EN60950

• VCCI

• IC (Canada):

- This Class B digital apparatus complies with Canadian ICES-003.

- Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

• Micron encryption algorithms have received the following NIST certifications:

– Micron AES Module Cert. #1704

– Micron DRBG Module Cert. #105

– Micron RSA Module Cert. #833

– Micron SHA 256 Module Cert. #1487

• Trusted Computing Group Storage Security Subsystem Class: Opal

FCC Rules

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference in a residential installation. This equip-

ment generates, uses, and can radiate radio frequency energy and, if not installed and

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Compliance

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice.

used in accordance with the instructions, may cause harmful interference to radio com-

munications. However, there is no guarantee that interference will not occur in a partic-

ular installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Compliance

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Package Dimensions

Figure 4: 2.5-Inch Package – 9.5mm

100.50mm/3.957in

for reference only

0.30mm

0.012in

for reference only

14.00mm

0.551in

90.60mm

3.567in

100.20mm ±0.25

3.945in ±0.010

4.07mm

0.160in

61.71mm

2.430in

D&T M3 x 0.5mm

(4 PLCS)

69.85mm ±0.25

2.750in ±0.010

14.00mm

0.551in

(bothsides)

90.60mm

3.567in

(bothsides)

3.00mm

0.118in

(2 PLCS)

(bothsides)

D&T M3 x 0.5mm

(2 PLCS)(bothsides)

3.50mm ±0.38

0.138in ±0.015

13.43mm/0.529in

for reference only 9.50mm ±0.20

0.374in ±0.008

9.40mm

0.370in 3.0mm RAD

0.12in

(4 PLCS)

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Package Dimensions

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 5: 2.5-Inch Package – 7mm

100.50mm/3.957in

for reference only

0.30mm/0.012in

for reference only

14.00mm

0.551in

90.60mm

3.567in

100.20mm ±0.25

3.957in ±0.010

4.07mm

0.160in

61.71mm

2.430in

3.0mm RAD

0.12in

(4 PLCS)

D&TM3 x 0.5mm

(4 PLCS)

14.00mm

0.551in

(both sides)

90.60mm

3.567in

(both sides)

3.00mm

0.118in

(2 PLCS)

(both sides)

D&TM3 x 0.5mm

(2 PLCS)(both sides)

3.50mm ±0.38

0.138in ±0.015

13.43mm/0.529in

for reference only 7.00mm+0.00

-0.20

0.276in+0.000

-0.008

9.40mm

0.370in

69.85mm ±0.25

2.750in±0.010

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Package Dimensions

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 32 Micron Technology, Inc. reserves the right to change products or specifications without notice.

References

• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available

at www.sata-io.org

• SATA 3.0 GOLD

• ATA-8 ACS2

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

References

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Revision History

Rev. A, Preliminary – 09/11

• Initial release

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900

www.micron.com/productsupport Customer Comment Line: 800-932-4992

Micron and the Micron logo are trademarks of Micron Technology, Inc.

All other trademarks are the property of their respective owners.

This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.

Although considered final, these specifications are subject to change, as further product development and data characterization some-

times occur.

C400 2.5-Inch NAND Flash Self-Encrypting Drive SSD

Revision History

PDF: 09005aef848722e9

realssd_c400_2_5_sed.pdf - Rev. A 09/11 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice.