V23809-C8-T11 - Infineon Technologies

Fiber Optics JULY 1999

11 dB V23809-C8-T10

Multimode 1300 nm LED Fast Ethernet/FDDI/ATM

170 MBd 1x9 Transceiver with ST Connector

FEATURES

• Compliant with Fast Ethernet, FDDI, Fibre Channel,

ATM/SONET/SDH standards

• Meets mezzanine standard height of 9.8 mm

• Compact integrated transceiver unit with duplex SC

receptacle

• Single power supply with 3.0 V to 5.5 V range

• Extremely low power consumption < 0.7 W at 3.3 V

• PECL differential inputs and outputs

• System optimized for 62.5/50 µm graded index fiber

• Industry standard multisource footprint

• Testboard available

• UL-94 V-0 certified

• ESD Class 2 per MIL-STD 883 Method 3015

• Compliant with FCC (Class B) and EN 55022

• For distances of up to 2 km on multimode fiber

APPLICATIONS

• ATM switches/bridges/routers

• Fast Ethernet, FDDI

• High speed computer links

• Local area networks

• Switching systems

Absolute Maximum Ratings

Exceeding any one of these values may destroy the device

immediately.

Supply Voltage (VCC–VEE)....................................... –0.5 V to 7 V

Data Input Levels (PECL) (VIN)..................................... VEE–VCC

Differential Data Input Voltage ............................................... 3 V

Operating Ambient Temperature (TAMB) ............ 0°C to 85°C

Storage Ambient Temperature ............................ –40°C to 85°C

Soldering Conditions, Temp/Time (TSOLD/tSOLD)

(MIL-STD 883C, Method 2003) .............................. 270°C/10s

ESD Resistance (all pins to VEE, human body) ..................1.5 kV

Output Current (IO)........................................................... 50 mA

*Available also as 8 dB V23809-C8-T11 on request

ST is a registered trademark of AT&T

(0.46) .02 x 9

(14.4) .567

(9.8) max.

.39 max.

(41.2) 1.622

(3.8) .15 max.

(2.8)

max.

.11

max.

(18.47) .727 (20.32) .8

(5.27) .207

(1) .039

(0.6)

.024

(3–0.2)

.118–.008

∅(1.4)

∅.055

2x ∅(0.1) MA M

bottom

view

∅(0.3) MA M

(1.4)

(25.4) max.

1 max.

(20.32)

(2.54)

(12.7)

Dimensions in (mm) inches

Fiber Optics V23809-C8–T10, MM 1300 nm LED Fast Ethernet/FDDI/ATM Transceiver (ST)

DESCRIPTION

This data sheet describes the Infineon Fast Ethernet/FDDI/ATM

transceiver—part of Infineon Multistandard Transceiver Family.

It is fully compliant with the Asynchronous Transfer Mode

(ATM) OC-3 standard, the Fiber Distributed Data Interface

(FDDI) Low Cost Fiber Physical Layer Medium Dependent (LCF-

PMD) draft standard(1)

, and the FDDI PMD standard(2).

ATM was developed because of the need for multimedia appli-

cations, including real time transmission. The data rate is scal-

able and the ATM protocol is the basis of the broadband public

networks being standardized in the International Telegraph and

Telephone Consultative Committee (CCITT). ATM can also be

used in local private applications.

FDDI is a Dual Token Ring standard developed in the U.S. by the

Accredited National Standards Committee (ANSC) X3T9, within

the Technical Committee X3T9.5. It is applied to the local area

networks of stations, transferring data at 100 Mbits/s with a

125 MBaud transmission rate. LCF FDDI is specially developed

for short distance applications of up to 500 m (fiber-to-the-desk)

as compared to 2 km for backbone applications.

Fast Ethernet was developed because of the higher bandwidth

requirement in local area networking. It is based on the proven

effectiveness of millions of installed Ethernet systems.

The Infineon multimode transceiver is a single unit comprised

of a transmitter, a receiver, and an ST receptacle. This design

frees the customer from many alignment and PC board layout

concerns. The modules are designed for low cost applications.

The inputs/outputs are PECL compatible and the unit operates

from a 3.0 V to 5.5 V power supply. As an option, the data out-

put stages can be switched to static levels during absence of

light, as indicated by the Signal Detect function. It can be

directly interfaced with available chipsets.

Notes

1. FDDI Token Ring, Low Cost Fiber Physical Layer Medium Depen-

dent (LCF-PMD) ANSI X3T9.5 / 92 LCF-PMD / Proposed Rev. 1.3,

September 1, 1992. American National Standard.

2. FDDI Token Ring, Physical Layer Medium Dependent (PMD) ANSI

X3.166-1990 American National Standard. ISO/IEC 9314-3: 1990.

Regulatory Compliance

TECHNICAL DATA

The electro-optical characteristics described in the following

tables are valid only for use under the recommended operating

conditions.

Recommended Operating Conditions

Notes

1. For VCC–VEE (min., max.). 50% duty cycle. The supply current

(ICC2+ICC3) does not include the load drive current (Icc1). Add max.

45 mA for the three outputs. Load is 50 Ω into VCC –2V.

2. To maintain good LED reliability, the device should not be held in the

ON state for more than the specified time. Normal operation should

be done with 50% duty cycle.

3. To achieve proper PECL output levels the 50 Ω termination should be

done to VCC –2 V. For correct termination see the application notes.

Feature Standard Comments

Electromagnetic

Interference (EMI)

FCC Class B

EN 55022 Class B

CISPR 22

Noise frequency

range:30 MHz to

1 GHz

Immunity:

Electrostatic

Discharge

EN 61000-4-2

IEC 1000-4-2

Discharges of

± 15kV with an air

discharge probe on

the receptacle cause

no damage.

Immunity:

Radio Frequency

Electromagnetic

Field

EN 61000-4-3

IEC 1000-4-3

With a field strength

of 10 V/m rms, noise

frequency ranges

from 10 MHz to

1 GHz

Eye Safety IEC 825-1 Class 1

Parameter Symbol Min. Typ. Max. Units

Ambient Temperature TAMB 070°C

Power Supply Voltage VCC–VEE 35.5V

Supply Current 3.3 V ICC 230 mA

Supply Current 5 V(1) 260

Transmitter

Data Input

High Voltage

VIH–VCC –1165 –880 mV

Data Input

Low Voltage

VIL–VCC –1810 –1475

Threshold Voltage VBB–VCC –1380 –1260

Input Data Rise/Fall,

20%–80%

tR, tF0.4 1.3 ns

Data High Time(2) ton 1000

Receiver

Output Current lO25 mA

Input Duty Cycle

Distortion

tDCD 1.0 ns

Input Data

Dependent Jitter

tDDj

Input Random Jitter tRJ 0.76

Input Center

Wavelength

lC1260 1380 nm

Electrical Output

Load(3)

RL50 Ω

Fiber Optics V23809-C8–T10, MM 1300 nm LED Fast Ethernet/FDDI/ATM Transceiver (ST)

Transmitter Electro-Optical Characteristics

Notes

1. Measured at the end of 5 meters of 62.5/125/0.275 graded index

fiber using calibrated power meter and a precision test ferrule.

Cladding modes are removed. Values valid for EOL and worst-case

temperature.

2. The input data pattern is a 12.5 MHz square wave pattern.

3. Center wavelength is defined as the midpoint between the two

50% levels of the optical spectrum of the LED.

4. Spectral width (full width, half max) is defined as the difference

between 50% levels of the optical spectrum of the LED.

5. 10% to 90% levels. Measured using the 12.5 MHz square wave

pattern with an optoelectronic measurement system (detector

and oscilloscope) having 3 dB bandwidth ranging from less than

0.1 MHz to more than 750 MHz.

6. Extinction Ratio is defined as PL/PH x 100%. Measurement system

as in Note 5.

7. Optical Power Low is the output power level when a steady state

low data pattern (FDDI Quiet Line state) is used to drive the trans-

mitter. Value valid <1 ms after input low.

8. Test method as for FDDI-PMD. Jitter values are peak-to-peak.

9. Duty Cycle Distortion is defined as 0.5 [(width of wider state) minus

(width of narrower state)]. It is measured with stream of Idle

Symbols (62.5 MHz square wave).

10.Measured with the same pattern as for FDDI-PMD.

11. Measured with the Halt Line state (12.5 MHz square wave).

Receiver Electro-Optical Characteristics

Notes

1. Pattern: Manchester coding / NRZI (no scrambling)

2. For a bit error rate (BER) of less than 1x10E–12 over a receiver eye

opening of least 1.5 ns. Measured with a 223–1 PRBS at 155 MBd.

3. For a BER of less than 1x10E-12. Measured in the center of the eye

opening with a 223-1 PRBS at 155 MBd.

4. Measured at an average optical power level of –20 dBm with a 62.5

MHz square wave.

5. All jitter values are peak-to-peak. RX output jitter requirements are

not considered in the ATM standard draft. In general the same

requirements as for FDDI are met.

6. Measured at an average optical power level of –20 dBm.

7. Measured at –33 dBm average power.

8. An increase in optical power through the specified level will

cause the SIGNAL detect output to switch from a Low state to

a High state.

9. A decrease in optical power through the specified level will

cause the SIGNAL detect output to switch from a High state to

aLow state.

10. PECL compatible. Load is 50 Ω into VCC –2 V. Measured under DC

conditions. For dynamic measurements a tolerance of 50 mV should

be added for VCC=5 V.

Transmitter Symbol Min. Typ. Max. Units

Data Rate DR 170 MBaud

Launched Power

(Average) into 62.5 µm

Fiber for –C8–C10(1, 2)

PO–20 –16 –14 dBm

Launched Power

(Average) into 62.5 µm

Fiber for –C8–C11(1, 2)

–22 –17

Center Wavelength(2, 3) λC1270 1360 nm

Spectral Width

(FWHM)(2, 4)

Dl170

Output Rise/Fall Time,

10%–90%(2, 5)

tR, tF0.6 2.5 ns

Temperature

Coefficient of Optical

Output Power

TCp 0.03 dB/°C

Extinction Ratio

(Dynamic)(2, 6)

ER 10 %

Optical Power Low(7) PTD –45 dBm

Overshoot OS 10 %

Duty Cycle

Distortion(8, 9)

tDCD 0.6 ns

Data Dependent

Jitter(8, 10)

tDDJ 0.3

Random Jitter(8, 11) tRJ 0.6

Receiver Symbol Min. Typ. Max. Units

Data Rate DR 5(1) 170 MBaud

Sensitivity

Average Power)(2)

PIN –33 –31 dBm

Sensitivity (Average

Power) Center(3)

–35.5

Saturation (Average

Power)(3)

PSAT –14 –11

Duty Cycle

Distortion(4, 5)

tDCD 1ns

Deterministic

Jitter(5, 6)

tDJ 1

Random Jitter(5, 7) tRJ

Signal Detect

Assert Level(8)

PSDA –42.5 –30 dBm

Signal Detect

Deassert Level(9)

PSDD –45 –31.5

Signal Detect

Hysteresis

PSDA–

PSDD

1.0 dB

Output Low

Voltage(10)

VOL–VCC –1810 –1620 mV

Output High

Voltage(10)

VOH–VCC –1025 –880

Output Data

Rise/Fall Time,

20%–80%

tR, tF1.3 ns

Output SD

Rise/Fall Time,

20%–80%

Fiber Optics V23809-C8–T10, MM 1300 nm LED Fast Ethernet/FDDI/ATM Transceiver (ST)

Pin Description

APPLICATION NOTE

Multimode 1300 nm 1x9 Transceiver

The power supply filtering is required for good EMI perfor-

mance. Use short tracks from the inductor L1/L2 to the module

VCC-Rx/VCC-Tx.

A GND plane under the module is recommended for good EMI

and sensitivity performance.

Pin Name Level/Logic Pin# Description

RxVEE Rx Ground Power Supply 1 Negative power supply, normally ground

RD Rx Output Data PECL Output 2 Receiver output data

RDn 3 Inverted receiver output data

RxSD RX Signal Detect PECL Output active high 4 High level on this output shows there is an optical signal.

RxVCC Rx +3.3 V...5 V Power Supply 5 Positive power supply, +3.3 V...5 V

TxVCC Tx +3.3 V...5 V 6

TxDn Tx Input Data PECL Input 7 Inverted transmitter input data

TxD 8 Transmitter input data

TxVEE Tx Ground Power Supply 9 Negative power supply, normally ground

Case Support Not Connected S1/S2 Support stud, not connected

GND

VCC

GND

VCC–RX

GND

VCC–TX

GND GND

VCC-TX

VCC-RX

Transceiver

82R

130R

GNDGND

VCC–TX

82R

130R

GNDGND

VCC–RX

200R

GND

R9 R8

RDN

TXD

TXDN

R2 R4

C1/3=4700 nF (optional)

C2/4=4700 nF

L1/2=15000 nH (L2 is optional)

R9=200 Ohm

R in Ohm 5 V 4 V 3.3 V

R1/3 82 100 127

R2/4 130 100 83

R5/7 82 100 127

R6/8 130 100 83

DC coupling between ECL gates.

Infineon Technologies AG • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany

Infineon Technologies, Corp. • Fiber Optics • 19000 Homestead Road • Cupertino, CA 95014 USA

Siemens K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku • Tokyo 141, Japan

www.infineon.com/fiberoptics

APPLICATION NOTE FOR MULTIMODE 1300 NM LED TRANSCEIVER

Solutions for connecting a Infineon 3.3 V Fiber Optic Transceiver to a 5.0 V Framer-/Phy-Device.

Figur 1. Common GND

Figure 2. Common VCC

Framer/Phy

Clock

Recovery

Infineon

Fiber

Optic

Transceiver

VCC VCC

Data

Out

500

127

180

VCC 5.0 V

VCC 3.3 V

100 nF

Framer/Phy

Clock

Recovery

Infineon

Fiber

Optic 3.3 V

Transceiver

VCC VCC

510

18K

VCC 5.0 V

VCC 3.3 V

Out

1.8 V

Zener-Diode 1.8 V

Framer/Phy

Clock

Recovery

Infineon

Fiber

Optic 3.3 V

Transceiver

VCC VCC

39K

127

26K

VCC 5.0 V VCC 3.3 V

Inputs and outputs are differential and should be

doubled. Signal Detect (SD) is single ended (if used).

Figure 1a. Circuitry for SD (Differential) and

Common GND

Figure 1b. Circuitry for SD (Single Ended)

and Common GND

Framer/Phy

Clock

Recovery

Infineon

Fiber

Optic

Transceiver

VCC VCC

Data

Out

VCC

GND 5.0 V

GND 3.3 V

200

83 127

130

Inputs and outputs are differential

and should be doubled. Signal

Detect (SD) is single ended.